Condition: ready for operation (used), functionality: fully functional, Year of construction: 2011, operating hours: 35,623 h, machine/vehicle number: A1225A0041 / L20, controller model: SINUMERIK 840D SL, laser power: 3,200 W, sheet thickness (max.): 20 mm, working length: 3,000 mm, working width: 1,500 mm, The machine was exclusively serviced by Trumpf until 2023 as part of a maintenance contract. TECHNICAL DETAILS Working length: 3,000 mm Working width: 1,500 mm Working height: 115 mm Travel range X-axis: 3,000 mm Travel range Y-axis: 1,500 mm Travel range Z-axis: 115 mm Maximum workpiece weight: 900 kg Sheet thickness steel max.: 20 mm Sheet thickness stainless steel max.: 12 mm Sheet thickness aluminum max.: 8 mm Sheet thickness max.: 20 mm Feed rate X-axis: 100 m/min Feed rate Y-axis: 200 m/min Feed rate Z-axis: 80 m/min Cutting speed: 140 mm/min Positioning speed X/Y-axis: 140 m/min Repeat accuracy: 0.05 mm Smallest programmable step: 0.001 mm MACHINE DETAILS Laser type: CO₂ laser Laser source manufacturer: Trumpf Laser source model: TruFlow 3200 Laser power: 3,200 W Dkolhezyakgjcdw Est Laser wavelength: 10,600 nm Cooling type: Water Control type: CNC control Control manufacturer: Siemens Control model: SINUMERIK 840D SL Automation level: Semi-automatic Operating type: Electric Input voltage: 400 V Input current: 100 A Input frequency: 50 Hz Dimensions & Weight Dimensions (L x W x H): 6,500 x 7,600 x 2,200 mm Total weight: 12,000 kg Laser hours NC control: 35,623 h Laser hours resonator / pump 1: 34,258 h Laser hours beam on / pump 2: 10,155 h EQUIPMENT CE marking Central lubrication system Cooling unit Documentation / manual Dust extraction Emergency stop switch Safety light curtain

Condition: ready for operation (used), Year of construction: 2000, functionality: fully functional, sheet thickness (max.): 3 mm, working length: 2,500 mm, TECHNICAL DETAILS Sheet thickness with tensile strength of 410 N/mm² max.: 2.00 mm Sheet thickness with tensile strength of 600 N/mm² max.: 1.25 mm Delhcozv Rc Ssdw Eokt Sheet thickness with tensile strength of 265 N/mm² max.: 3.00 mm Minimum sheet thickness: 0.50 mm Length of the notched plate at the inlet max.: 2,700 mm Width of the notched plate at the inlet max.: 1,500 mm Rotatable diagonal of the notched plate max.: 2,700 mm Bending length max.: 2,500 mm Clearance for bending above the work table max.: 127 mm MACHINE DETAILS Processor: Intel Pentium III, 500 MHz RAM: 128 MB SDRAM Graphics memory: 4 MB SGRAM Hard disk capacity: 9.1 GB CD-ROM drive: 600 MB Floppy disk drive: 3.5 inch, 1.44 MB Network cards: 2 Screen diagonal: 17 inches Voltage: 400 V Frequency: 50 Hz Number of phases: 3 Rated power: 38 kW Rated current: 64 A Switching capacity of the main switch: 40 kA Further technical details can be found in the attached documents.

Condition: excellent (used), Year of construction: 1988, total width: 810 mm, total length: 1,700 mm, total height: 1,700 mm, overall weight: 1,250 kg, Eckold Kraftformer; motorised machine for Shrinking, Stretching, Doming, Planishing, Reforming, Flattening, Straightening Machine equipped for tooling: FWR1307 FWA 1306 FWA 802T FWA 1002T LFA 120S LFA155T Number of strokes: 300 / 600Min. Maximum sheet thickness:4.0mm Horizontal troath: 460mm Vertical troath: 475mm Max. thickness Stainles:2.0mm Max. thickness Aluminium:5.0mm Motorised ram adjustment:0 - 60 Power: 3.0kW Length: 1700mm Width: 810mm Height: 1700mm Weight: 1250kg Dkslszzmtkehcdw Ejt Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: like new (used), Year of construction: 2002, machine/vehicle number: 54, functionality: fully functional, pressing force: 60 t, table width: 1,100 mm, table length: 3,000 mm, The machine is in like-new condition! Submitting a bid obligates you to pick up the machine on the following dates: Monday, October 5, 2026, Tuesday, October 6, 2026, Wednesday, October 7, 2026, and Thursday, October 8, 2026, until 12:00 PM. The machine is already in storage. Dkjlhcdozzny Sew Est TECHNICAL DETAILS Punching force: 60 t Table size: 1,100 × 3,000 mm EQUIPMENT Setup operation Automatic operation Continuous operation Wiring diagrams Operating manual

Condition: excellent (used), functionality: fully functional, Year of construction: 2012, Used 3-meter CNC plate shear from ERMAK Type: CNC HVR 3106 Delhezzpfcocdw Eekt Cybelec DNC 60 control system Capacity: 3100 x 6 mm Electric back gauge Electric cutting angle adjustment Electric cutting clearance adjustment Year of manufacture: 2012

Condition: excellent (used), Year of construction: 2012, Used 3-meter CNC press brake from Ermaksan Type: Powerbend Pro 30120 Capacity: 3100 x 120 tons Year of manufacture: 2012 Cybelec DNC 660 CNC control (2D graphic) Y1, Y2, X, and R axes CNC controlled CNC crowning Euro-style tool clamping Djlhozzpc Iecdw Ejkt 1 set of tools for 1 to 6 mm

Condition: good (used), functionality: fully functional, Year of construction: 2010, machine/vehicle number: SY 330 -075, control type: CNC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: Akyapak, number of rollers: 4, roller (bottom) diameter: 300 mm, roller (top) diameter: 330 mm, overall weight: 9,100 kg, total length: 4,585 mm, total width: 1,610 mm, total height: 1,840 mm, input voltage: 400 V, input current: 35 A, input frequency: 50 Hz, Equipment: documentation/manual, emergency stop, foot remote control, hardened rollers, The sale includes a 2-meter longitudinal welding station equipped with an Oerlikon MIG 500 A welding unit, with all equipment in full working order. Also included are a lifting table for material handling to the plate rolling machine and a work platform. The plate rolling machine is in good condition and can be put into production immediately. The machine is currently operational, and inspection and test runs can be arranged upon request. Dkjlhcdwozzdaho Est With the inclusion of the longitudinal welding station, this package provides a complete solution for manufacturing tubes and special pipe sections to customer-specified diameters, with lengths of up to 2 meters.

Condition: good (used), Year of construction: 1987, Press force 1250 t Bending length 15000 mm Upright spacing 10160 mm Control system CNC 10 graphics Throat depth 770 mm Table length 15000 mm Machine weight approx. 230 t Required space approx. 17000 x 5400 x 5900 mm Dslozzl T Aehcdw Eokt Additional information: - Press force: 1,250 t - Bending length: 15,000 mm - Control: CNC 10 graphics - Number of controlled axes: at least 10 - Upright spacing: 10,160 mm - Throat depth: 770 mm - Table length: 15,000 mm - Dimensions: 17,000 mm x 5,400 mm x 5,900 mm - Weight: approx. 170 t Equipment: - Crowning device - CNC 10 graphic control - Hydraulic upper tool clamping - Multi-operator functionality - Increased speeds - Automatic, height-adjustable rear sheet gauge - Draw cushion device - Horn length on each side: 2,200 mm

Condition: used, MANFACTURER - PRO-ECO TYPE - PRECISION DOUBLE LOOP SLITTING LINE MATERIAL - GRAIN ORIENTED, NON-GRAIN ORIENTED, SILICON STEEL, COLD ROLLED STEEL SHEAR STRESS - 100,000 PSI - SILICON STEEL | 60,000 COLD ROLLED STEEL MAX YIELD STRESS - 80,000 PSI MIN YIELD STRESS - 30,000 PSI MAX COIL WEIGHT - 50,000 LBS ENTRY/EXIT MAX COIL WIDTH - 48" NOMIMAL (50" MAXIMUM) ENTRY/EXIT MIN COIL WIDTH - 8" ENTRY / 1" EXIT MAX COIL OD - 72" ENTRY / EXIT MIN COIL OD - 36" ENTRY / EXIT MAX STRIP THICKNESS - 0.025" IN - SILICON STEEL / 0.050" CRS MIN STRIP THICKNESS - 0.010" MAX CUTS - 32 LINE SPEED - 1200 FPM ELECTRICAL - 575 V, 3 PH, 60 CYCLE AIR SUPPLY - 80 PSI LINE DIRECTION - LEFT TO RIGHT MODE OF OPERATION - FULL LOOP DRIVE-SLIT, DOUBLE LOOP LINE COMPONENTS: COIL CAR MANDREL UNCOILER PEELER TABLE ENTRY PIT GUIDE TABLES INTERMEDIATE GUIDES FELT STAND BEFORE ENTRY SHEAR ENTRY SHEAR SIDE GUIDES SLITTING HEAD BUTECH SCRAP CHOPPERS EXIT TABLE PRESSURE & TENSION ROLL STAND EXIT SHEAR Dkelhjzk Nitjcdw Ejt RECOILER WITH OVERARM SEPARATOR EXIT COIL CAR ALSO AVAILABLE: INTEGRATED PACKAGAING LINE, INCLUDING: EXIT TURNSTILE DOWNENDER WEIGHT SCALE UNDER SEMI-AUTOMATED BANDING LINE 5/8" STEEL BANDING PICK AND PLACE STACKER MAX CAPACITY 6000 LBS PER SLIT COIL ROTATING CAROUSEL EXIT CONVEYOR SEMI-AUTOMATIC STRETCH WRAPPING MACHINE WEIGHT STATION CONTROLS, HYDRAULICS AND ELECTRICS FOR LINE

Condition: good (used), Year of construction: 1999, power: 16.5 kW (22.43 HP), pressing force: 115 t, stroke length: 250 mm, operating speed: 10 mm/s, table width: 95 mm, table length: 4,100 mm, throat depth: 300 mm, distance table to ram: 350 mm, clearance between the columns: 3,700 mm, total length: 4,800 mm, total width: 2,200 mm, total height: 3,600 mm, overall weight: 18,500 kg, distance between stands: 3,700 mm, Press brake, bending length 4100 mm, capacity 115 to, control DELEM DA 65, gap between column 37000 mm, stroke 250 mm, throat gap 300 mm, motor 16,5 KW, back gauge 800 mm motorized, dimension 4800x2200x3600 mm, weigth ca. 1850,0 kgs, tools Dkelhcdwszzpwlj Ejt

Condition: good (used), Year of construction: 1964, number of straightening rollers: 17, straightening roller diameter: 45 mm, Sheet width: 1650 mm Sheet thickness: 4 mm Straightening roller diameter: 45 mm Support rollers: 140 pieces Dkelozzl H Njhcdw Eet Straightening rollers: 17 pieces

Condition: excellent (used), Year of construction: 1990, functionality: fully functional, power: 5.5 kW (7.48 HP), pressing force: 80 t, stroke length: 150 mm, total length: 3,180 mm, total width: 1,250 mm, total height: 2,450 mm, overall weight: 6,000 kg, Equipment: documentation/manual, Accessories: 3 x bending prism, 3 x top beam, several bending segments, backstop, stroke counter, manual night operation. Technical parameters: Rated force 800 kN, Working table length 2500 mm, Table width 160 mm, Ram speed: downward 50 mm/s, pressing 10 mm/s, upward 100 mm/s, Maximum ram stroke Z 150 mm, Distance between side frames B 2050 mm, Overhang A 250 mm, Maximum opening height H 380 mm, Parallel ram stroke accuracy 0.1/1000 mm, Working fluid pressure 24 MPa, Electric motor power: main 5.5 kW, Machine dimensions: length (with cabinet) 3180 mm, width 1250 mm, height 2450 mm, Machine weight 6000 kg. The machine can be tested in our warehouse in Přerov by arrangement. Dkslhcdozzffrsw Est

Condition: good (used), Year of construction: 1982, Year of construction / YOM: 1982/2024 Sheet width: 2000 mm Sheet thickness - max.: 10 mm Sheet thickness - min.: 3 mm Djlhezzlzaecdw Ejkt Number of straightening rollers: 13 rollers Straightening roller diameter: 145 mm Straightening speed: 16 m/min Bundle length: 2330 mm Center distance between straightening rollers: 150 mm Support roller diameter: 290 mm Main drive motor: 30 kW Weight: 32 t Additional information: - Number of support rollers: 21/24 - Number of supports (top/bottom): 3 /3 - Traverse lift speed: 0.71 mm/sec - Traverse lift stroke: -18 mm to +42 mm - Max. tilting of lower traverse: 8 mm

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1985, machine/vehicle number: 8444-08, workpiece length (max.): 6,000 mm, No minimum price – guaranteed sale to the highest bidder! Dolhcdwjzy Ndcs Eekt TECHNICAL DETAILS Maximum edge length: 6,000 mm Maximum material thickness: 1.25 mm Mechanical cutting device Hydraulic unit Flow rate of gear pump: 14.5 l/min Operating pressure: 140 bar Maximum pressure: 210 bar Electric motor power: 3 kW Motor speed: 1,450 rpm Voltage: 380 V Frequency: 50 Hz Oil tank capacity: 30 l Pressure gauge diameter: 63 mm Pressure gauge display range: 0–250 bar Pressure switch: 90 bar Hydraulic components Gear pump CPL 9 DQ Intermediate flange L25-2/004 Elastic coupling G 228/2P Return filter Fill and vent filter Oil level indicator Drain plug Glycerine pressure gauge Valve block with pressure, flow control, braking, and solenoid valves Hydraulic cylinders Number of hydraulic cylinders: 8 Type: GHZ-50 × 225-S spec. Piston rod with external thread M20 Length: 20 mm Swivel bearing at the rear Hydraulic motors Number of hydraulic motors: 4 Type: OMP 50 MACHINE DETAILS Control system Electrical machine control with operator panel (OP) Adjustable dwell times, angle ranges, and shutdown delays Variant control for different machine functions EPROM-based control Electrical supply Mains voltage: 380 V Frequency: 50 Hz EQUIPMENT Hydraulic unit OP-14 SM 8 hydraulic cylinders GHZ-50 × 225-S spec. 4 hydraulic motors OMP 50 Gear pump CPL 9 DQ Valve block with hydraulic valves Return filter Fill and vent filter Oil level indicator Glycerine pressure gauge Pressure switch Electrical OP control Hydraulic and electrical circuit diagrams

Condition: ready for operation (used), Year of construction: 2007, pressing force: 28 t, stroke length: 200 mm, throat depth: 200 mm, installation height: 325 mm, working length: 835 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Press force: 28 t Bending length: 835 mm Travel range of the back gauge: 0 – 370 mm Stroke: 200 mm Distance between frames: 890 mm Support table: 200 x 275 mm Overhang: 200 mm Installation height: 325 mm Number of cylinders: 1 Dkslhcdjzzkwgjw Eet Working speed Press travel: 8-10 mm/s Retraction: max. 35 mm/s Positioning accuracy: +/- 0.05 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 1,600 x 1,500 x 2,200 mm Total weight: 3,500 kg EQUIPMENT Operating manual Safety device Mechanical tool clamping (top) The height and weight of the asset must be taken into account when selecting the transport vehicle. A forklift is available for loading. If the asset is not collected on time, a storage fee of €20.00 per lot and per day (or part thereof) will be charged. The fee must be paid before collection. The sale is made without any warranty or guarantee. The information on the technical data comes from the original offer. No guarantee is given for typographical or measurement errors. If in doubt, please compare the information with the photos provided or inspect the goods on-site before the end of the auction.

Condition: used, Year of construction: 2000, machine/vehicle number: 40 3000 1027, Item No. 26254 Technical data: - max. working width 1310 mm Delhcdezzprvsw Eskt - max. material thickness 2 mm - bending angle approx. 0 - 135 ° - upper beam is operated with a side hand crank - max. stroke of upper beam 85 mm - max. adjustment of bending beam 80 mm - bending process is supported by an eccentric weight - space requirement approx. W 2250 x H 1250 x D 450 mm - weight approx. 620 kg

Condition: good (used), Year of construction: 1969, max. sheet width: 2500 mm Convexity length of rollers: 2700 mm max. sheet thickness (St 50): 32 mm max. sheet thickness (St 34): 39 mm min. sheet thickness (St 50): 8 mm Dkelhcdwjzzdcco Ejt number of straightening rollers: 7 rollers number of driven straightening rollers: 5 rollers diameter of straightening rollers: 290 mm diameter of input/output straightening rollers: 345 mm number of support rollers: 13 diameter of support rollers: 288 mm stroke of upper beam: 120 mm Straightening speed: 16 m / min Rated power of main drive: 90 kW Total load: 138 kW

Condition: like new (used), functionality: fully functional, Year of construction: 2024, operating hours: 15 h, machine/vehicle number: 121282, BENDMAK PRO 120 – Hydraulic three-roll profile and tube bending machine | 2024 | only 15.5 hours of use We offer a nearly new hydraulic three-roll profile and tube bending machine, BENDMAK PRO 120, manufactured in 2024. The machine has been used only minimally. The control system currently shows only 15 hours and 27 minutes of machine operating time and 31 hours and 14 minutes of hydraulic operating time. Operating times can be verified directly on the machine's display – see photos. The machine is fully functional, in very good technical condition, and ready for immediate use. The sale includes an extensive set of interchangeable rolls/tools for bending various profiles and tubes, as shown in the photos. Dkelhcdezzkvpow Ejt Technical data: Manufacturer: BENDMAK Model: PRO 120 Year of manufacture: 2024 Serial number: 121282 Machine operating hours: 15:27 h Hydraulic operating hours: 31:14 h Type: hydraulic three-roll profile bending machine Shaft diameter: 120 mm Working roll diameter: 390 mm Motor power: 11 kW Power supply: 400 V / 50 Hz Weight: 4,720 kg CE Equipment and accessories: hydraulically controlled lower rolls hydraulic side guide rolls drive for all three rolls separate mobile control panel touchscreen display multiple sets of interchangeable rolls/tools for various profiles and tubes accessories shown in the photos are included in the sale The machine can be inspected and demonstrated in operation on-site.

Condition: repair required (used), Year of construction: 2007, Roller profiling line for manufacturing profiles for dry construction, without a hydraulic unit. Dslhcozy Ekfedw Ejkt Location: In our workshop.

Condition: excellent (used), Year of construction: 2002, machine/vehicle number: B0104A0167, functionality: fully functional, operating hours: 29,966 h, pressing force: 130 t, stroke length: 215 mm, overall weight: 11,250 kg, 6 controlled axes Includes new tools worth €12,000!!! Dslhcdozy Ryxew Eekt Everything is fully functional.

Condition: good (used), Year of construction: 2014, pressing force: 100 t, table length: 3,050 mm, clearance between the columns: 2,550 mm, overall weight: 7,700 kg, Press force: 100 t Bending length: 3050 mm Distance between uprights: 2550 mm Dsloztakgshcdw Ejkt Total power requirement: 20 kW Machine weight approx.: 7,700 kg Accessories/Equipment: - Light curtain in front of the machine - AMADA tool holder with quick-release mechanism - Tools - 2 stop fingers - DELEM DA 60 touch control system - Foot switch - Side protective doors - Operating hours: 2,948 h - 6 axes, Y1, Y2, X, R, Z1, Z2

Condition: like new (used), Year of construction: 2022, controller model: Siemens Touch Panel KTP 600, bending angle (max.): 180 °, bending radius (max.): 200 mm, overall weight: 500 kg, power: 1.5 kW (2.04 HP), No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Bending direction: right Tube diameter steel: 4–28 × 3 mm Tube diameter non-ferrous metals: 4–35 × 2 mm Bending radius: max. 200 mm Bending height: 25 mm Bending speed: up to 45 °/s Effective bending angle: up to 180° + 10° overbending Switch-off accuracy: 0.1° Tube feed length: 1,500 mm MACHINE DETAILS Control: electronic Control model: Siemens Touch Panel KTP 600 Bending axis: electronically controlled Bending angle switching: automatic Program memory: 100 programs with 20 data sets each Target/actual value display for bending angle Tube clamping: hydraulic Clamping pressure: adjustable Slide block positioning: hydraulic Bending mandrel retraction: hydraulic Pump type: HD gear pump Pump capacity: 4.5 l/min Hydraulic pressure: 180 bar Bending head: free-standing Control panel: swiveling Machine design: mobile Maximum sound level: approx. 78 dB(A) Drive type: electro-hydraulic Drive power: 1.5 kW Mains voltage: 400 V Frequency: 50 Hz Phases: 3 Control voltage: 24 V DC Electrical standard: VDE Protection class: IP54 Dimensions & Weight Dimensions (L x W x H): 2,200 x 600 x 1,100 mm Weight: 475 kg EQUIPMENT Siemens Touch Panel KTP 600 Function keys with plain text display for operator guidance Automatic bending angle switching Target/actual value display for bending angle Delhcdwszzlc Ro Eskt Swiveling control panel Free-standing bending head Hydraulic tube clamping with adjustable clamping pressure Hydraulic slide block positioning Hydraulic bending mandrel retraction Mobile machine design The height and weight of the asset must be considered when selecting the transport vehicle. A forklift is available for loading. If the item is not collected on time, a storage fee of €20.00 per lot and commenced day will be charged. The fee must be paid before collection. The sale is made with the exclusion of any warranty or guarantee. The information on the technical data is based on the original offer. No guarantee is given for printing or measurement errors. If in doubt, please compare the information with the provided photos or inspect the goods on site before the end of the auction.

Condition: good (used), Year of construction: 2005, functionality: fully functional, Press force: 400 t Bending length: 4050 mm Distance between uprights: 3550 mm Control system: CYBELEC ModEva 10 S Total power requirement: 47 kW Machine weight: approx. 30,400 kg Space requirement: approx. 6000x3000x3450 mm Accessories/Equipment: - 2 bending aids in front of the machine - 2 controlled stop fingers - 1 manually adjustable stop finger - Light curtain in front of the machine Dkjlsy Ew E Ijhcdw Est - Control system: CYBELEC ModEva 10 S - Parking space on the right for the bending aid - Die shifting - Tool holder on the top and bottom, EHT pneumatic - Crowning - Pneumatic tool shifting - Foot switch - Side protective doors - Controlled axes: Y1 - Y2 - R - Z1 - Z2 - inclination

Condition: ready for operation (used), Year of construction: 2023, machine/vehicle number: 7.376.230.761, functionality: fully functional, operating hours: 2,216 h, pressing force: 400 t, stroke length: 365 mm, throat depth: 630 mm, controller model: Durma DT-15, working width: 4,050 mm, TECHNICAL DETAILS Press force: 400 t Max. working width: 4,050 mm Frame spacing: 3,400 mm Overhang: 630 mm Max. stroke: 365 mm Crowning system: CNC-controlled Delhcdwjzzbafo Eokt Ram holder: Quick-release system Tool holder type: European style MACHINE DETAILS Drive system: CNC Control system: Durma DT-15 Number of axes: 4 (Y1 + Y2 + X + R) Dimensions & Weight Dimensions (L x W x H): 5,750 x 2,110 x 3,640 mm Weight: 27,760 kg Transport packages: 1 Operating hours: 2,216 h EQUIPMENT Tools Finger guard CE marking CE certificate Documentation Tools

Condition: used, Year of construction: 2019, total length: 3,750 mm, total width: 1,900 mm, total height: 2,900 mm, Colour: Cream Weight: 12.620 kg Price: On request - Details: - └ Description: Machine errors. Cannot reference axes. Needs repair. - Year: 2019 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 73431915241 - Drive system: CNC - Control system brand: Delem - Control system type: DA-66T - Power [kW]: 22.0 - Number of axes [pcs]: 6: Y1+Y2+X+R+Z1+Z2 - Press force [ton]: 220 - Max. working width [mm]: 3050 - Column gap [mm]: 2500 - Max. stroke [mm]: 265 - Crowning system: CNC-controlled - Punch holder: Hydraulic - Tool holder type: WILA-standard - Tools included: Yes - Options: Finger safety guard, Angle measuring system - Transport dimensions: 3750mm x 1900mm x 2900mm (l x w x h) - Transport weight [kg]: 12620kg Dkelhcezzb I Aedw Est - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum