Condition: used, Manufacturer: Hylatechnik Paul Chrubasik GmbH Type: HSSP 300-3-XA4 Machine type: Hydraulic press Year of manufacture: 2000 Condition: used Press force: 3,000 kN Press force: 300 t Stroke: 300 mm Maximum installation height: 800 mm Table area: 2,000 × 1,550 mm Njdpfozrz D Ssx Alfsda Ram area: 2,000 × 1,540 mm Front opening: 2,000 mm Side opening: 1,050 mm Table height: 800 mm Rapid traverse: 340 mm/s Working speed 1: 32.5 mm/s Working speed 2: 19.5 mm/s Retraction: 340 mm/s Maximum working pressure: 280 bar Drive power: 75 kW Power supply: 400 V Frequency: 50 Hz Machine weight: approx. 38,500 kg Hydraulic oil tank: approx. 2,000 l Pulling cushion: no Equipment: Complete DREHER strip system DREHER strip unwinder DREHER strip feeder DREHER strip conveyor system Hydraulic die cushion with parallel movement Hydraulic roll blocks Tool changing consoles Siemens SIMATIC control panel Note: The system is currently running at a slow speed but has no significant damage. We will gladly send you videos of the machine in operation upon request.

Condition: used, Year of construction: 2003, Manufacturer: Haulick + Roos GmbH Type: RVD 3000-2500 Machine Type: High-performance stamping press Year of manufacture: 2003 Condition: used Rated pressing force: 3,000 kN Pressing force: 300 t Stroke frequency: 20–180 strokes/min Drive power: 80 kW Ram stroke: 20–160 mm Ram adjustment: 150 mm Tool installation height: max. 450 mm Maximum tool length: 2,500 mm Maximum tool width: 1,000 mm Table area: 2,450 × 1,000 mm Ram area: 2,500 × 950 mm Clamp plate opening: 2,250 × 350 mm Machine weight: approx. 46,000 kg Strip feed direction: right to left Power supply: 400 V Frequency: 50 Hz Maximum connected load: 80 kVA Maximum fuse rating: 250 A Draw cushion: not available Components of the system: Haulick + Roos high-performance stamping press RVD 3000-2500 DIMECO coil unwinder, type 23S1/D/VV Year of manufacture: 2003 Weight: 1,450 kg Maximum load capacity: 4,000 kg DIMECO roller feed, type 1681/17/BVV Year of manufacture: 2003 Weight: 540 kg ARKU straightening machine Technical data for roller feed: Strip width: 5–420 mm Strip thickness: 0.1–5 mm Maximum strip cross-section: 1,000 mm² Strip speed: up to 125 m/min Feed length: 0.1–999.9 mm Feed accuracy: ±0.1 mm Ndsdpfxozrz Dxo Alfoa Roller diameter: 100 mm Strip height adjustment: 100 mm, manual mechanical Note: The ram guide should be replaced. The system is currently still in operation and functional. A quote from the manufacturer for complete disassembly and installation of new guides is available for approximately €200,000. We will gladly provide videos of the system in operation upon request.

Condition: used, Year of construction: 1987, functionality: fully functional, power: 1.1 kW (1.50 HP), overall weight: 1,500 kg, Eccentric press EBU H16 Year of manufacture: 1987, 1500 kg, 1.1 kW Location: Bad Tölz Ndedpfezv Sl Iex Alfoa Inspection is welcome. We have other used machines available. Please contact us.

Condition: used, Year of construction: 1977, pressing force: 75 t, Eccentric press EBU SK75 U Year of manufacture: 1977 Location: Bad Tölz Ndodpozv Skdsfx Alfsa Inspection is welcome. We have other used machines available. Please feel free to contact us.

Condition: good (used), Year of construction: 1985, power: 1.5 kW (2.04 HP), overall weight: 1,700 kg, Eccentric press EBU H25 Ndedpezv Sitofx Alfoa Year of manufacture: 1985 Location: Bad Tölz Inspection is welcome. We have other used machines available. Please feel free to contact us.

Condition: used, Year of construction: 2005, Pressure 800 t distance between columns 2560 mm stroke 1050 mm Distance table/ram, stroke up 1870 mm Table surface area 2500 x 1730 mm pressure of drawing cushion in table 300 t Die cushion stroke in table 395 mm Njdpjzrpt Isfx Alfsda Die cushion area in table 2300 x 1300 mm Ram surface 2500 x 1730 mm Die cushion pressure in ram 63 t Die cushion stroke in ram 150 mm Side window 1000 mm Oil volume 4300 l Power capacity 200,0 kW Dimensions (WxDxH) 4,1 x 2,8 x 10,0 m Height above floor 7,0 m year of manufacture 1974 overhaul 2005: formerly type BZE 800, converted to ZE 800 by manufacturer with new ram and new cylinder mit ölhydraulischem Antrieb, hydraulischem gesteuertem Ziehkissen im Tisch und Stößel stored in dismantled condition - Video at seller’s site before dismantling available

Condition: used, Year of construction: 2005, Pressure 600 t distance between columns 2600 mm stroke 900 mm Distance table/ram, max. stroke up, adjustment up 1600 mm Table surface area 2500 x 1730 mm pressure of drawing cushion in table 250 t Die cushion stroke in table 400 mm Die cushion area in table 2300 x 1300 mm Die cushion pressure in ram 63 t Die cushion stroke in ram 160 mm Die cushion area in ram 1900 x 1300 mm Nedpfezrptzox Alfoda Ram surface 2500 x 1730 mm Side window 1100 mm Oil volume 3500 l Power capacity 200,0 kW Dimensions (WxDxH) 4,1 x 2,8 x 9,6 m Height above floor 6,4 m year of manufacture 1974 - overhaul 2005: complete new electrical cabinet with control Siemens S7 and safety control Pilz with oil-hydraulic drive, hydraulic controlled drawing cushion in table and ram, hydraulic cutting impact cushioning stored in dismantled condition - Video at seller’s site before dismantling available

Condition: used, Year of construction: 1998, Pressure 800 t distance between columns 3550 mm stroke 1100 mm Distance table/ram, max. stroke up, adjustment up 1900 mm Table surface area 3500 x 1800 mm pressure of drawing cushion in table 350 t Die cushion stroke in table 280 mm Die cushion pressure in ram 80 t Die cushion stroke in ram 160 mm Ram surface 3500 x 1800 mm Side window 1900 mm Weight 100,0 t Floor Space (WxD) 5,3 x 4,3 m Height above floor 7,3 m Height below floor 5,0 - 6,0 m Ndsdpfx Ajzrptnjlfea year of manufacture 1970 - overhaul 1998 with oil-hydraulic drive, hydraulic controllable drawing cushion in table and ram, hydraulic cutting impact cushioning, moving table (without rails for the moving table) Height beneath floor approx. 5 - 6 m stored in dismantled condition - Video at seller’s site before dismantling available

Condition: new, neu ca. 12 Wochen ab Auftrags Türkei Ndodpfx Aleynm Nmefsa 17850 € 342.72 € 100 to fix 1020 mm 300 mm 1020 mm 680 mm 9 mm/s 5 mm/s 10 mm/s 6 mm 500x1020 mm 100 mm 190 mm 2110 mm 1000 mm 2275 mm 2082 kg 2 guidings big upper tool holder and table with t-slots upper and lower pressbrake tool manometer rapid down move with automtic change to working speed piston stops in every position 2 hand panel AND FOOT PEDAL Tisch höhenverstellbar according to CE regulations user manual in GERMAN and ENGLISH

Condition: used, Two eccentric presses are offered. 1) ETH 3 eccentric press, pressing capacity: 30000kg, cutting area for material with 45kg strength: 665mm², ball screw adjustment: 40mm. Including protective cover and separate control cabinet. 2) An eccentric press with C-frame design, design: C-frame with flywheel, die clamping: hydraulic clamping device on the table. Including safety enclosure. An on-site inspection is possible. Nedpfx Aszvy Hajlfoda

Condition: used, Year of construction: 1998, machine/vehicle number: 1 / 2000, Pressure total: 2000 ton Ram stroke: 900 mm Slide adjustment: 800 mm Shut height (stroke down, adjustment up): 1800 mm Free frontal opening L-R: 5040 mm Distance between oil tray: 4840 mm Distance between the columns F - B: 2600 x 2400 mm Table surface area : 5000 x 2700 mm Slide area: 5000 x 2700 mm Die cushion capacity in table: 400 ton Die cushion stroke: 350 mm Die cushion pad area: 4200 x 2100 mm Cushion pressure in ram: 200 ton Ejector stroke in ram: 200 mm Number of strokes: 8 - 14 s.p.m. Required power: 350 kW Height over floor approx.: 11350 mm Die weight at the ram max.: 40000 kg Die Weight total: 80000 kg Weight of machine approx.: 580 ton Standard configuration Moving bolster front sidePin diameter 52 mmForce in microinches = 400 tA SIEMENS control system is installed Nsdpeyvz U Iefx Alfjda The documentation is available.A packing list would be available, as an identical press has already been dismantled.

Condition: used, Year of construction: 1998, machine/vehicle number: 2 / 2000, Pressure total: 2000 ton Ram stroke: 900 mm Slide adjustment: 800 mm Shut height (stroke down, adjustment up): 1800 mm Free frontal opening L-R: 5040 mm Distance between oil tray: 4840 mm Distance between the columns F - B: 2600 x 2400 mm Table surface area : 5000 x 2700 mm Slide area: 5000 x 2700 mm Die cushion capacity in table: 400 ton Ndjdpfoyvz Stjx Alfsa Die cushion stroke: 350 mm Die cushion pad area: 4200 x 2100 mm Cushion pressure in ram: 200 ton Ejector stroke in ram: 200 mm Number of strokes: 8 - 14 s.p.m. Required power: 350 kW Height over floor approx.: 11350 mm Die weight at the ram max.: 40000 kg Die Weight total: 80000 kg Weight of machine approx.: 580 ton Standard configuration Moving bolster front sidePin diameter 52 mmForce in microinches = 400 tA SIEMENS control system is installed The documentation is available.A packing list would be available, as an identical press has already been dismantled.

Condition: used, Year of construction: 1983, nominal force 2500 t stroke 600 mm cycle time 13 - 18 s distance between columns 1720 mm Distance table/ram, max. stroke up, adjustment up 2600 mm table surface area 1720 x 1800 mm allowed max. force 4000 t blow die to die 5000 t ram surface 2100 x 1320 mm capacity of ejector in table 40 t ejector stroke in table 250 mm ejector surface area in table 900 x 820 mm capacity of ejector in ram 6 t ejector stroke in ram 40 mm Ndjdpezrpuljfx Alfsa spindle diameter 425 mm power requirement 900,0 kW weight 335,0 t Dimensions (WxDxH) 3,4 x 4,6 x 9,7 m height over floor 8,3 m fully automated forging line / spindle press with automation for the production of flanged shafts for hot forming only with reversible AC motor, pneumatic brake, plate ejector in table (40 t / 250 mm), ejector in ram (6 t / 40 mm), lifting device for repositioning, marking, tool change, insertion device, tilting device, loading and unloading arm, rotary table, circular oil lubrication, centralised grease lubrication cycle time approx. 13 - 18 s as is where is, WITHOUT putting into operation

Condition: used, Year of construction: 1987, pressure 2000 t Nedpfxezrpr Re Alfsda distance between columns 975 mm stroke 400 mm distance table/ram, max. stroke up, adjustment up 1000 mm table surface area 1015 x 1050 mm table height over floor 800 mm capacity of ejector in table 6,3 t ejector stroke in table 100 mm capacity of ejector in ram 65 t ejector stroke in ram 100 mm ram surface 975 x 1050 mm return capacity 150 t speed down 235 mm/s speed up 250 mm/s working speed 5 - 20 mm/s oil volume 4000 l height over floor 3,65 m height beneath floor 3,75 m power requirement 194,0 kW weight 105,0 t dimensions (WxDxH) 5,0 x 6,5 x 7,4 m Calibrating press with oil-hydraulic drive, hydraulic ejector in table and ram

Condition: new, pressure 100 kN stroke 0-200 mm table-size 450 x 1000 mm working speed: 6-10 mm/ sec. return speed 20 mm/sec work height max. 900 mm toolpiece height max. 200 mm total power requirement 1,5 kW bending capacity max. - round 42x3,2 mm Ndsdszr Rp Djpfx Alfja 150x10 mm weight 320 kg dimensions 1010x480x1120 mm

Condition: ready for operation (used), Year of construction: 1987, functionality: fully functional, pressing force: 200 t, Hans Schoen NH/LF 200 (UVV) – Powerful & Robust 🔧 Model: Hans Schoen NH/LF 200 📍 Type: Hydraulic Double-Column Press (UVV-certified) 📅 Year of manufacture: approx. 1988 (depending on the specific machine) 📦 Condition: used, fully functional ⸻ 💪 Technical Highlights • Pressing force: approx. 200 t – suitable for demanding forming and drawing applications • Hydraulic drive for precise force and stroke control • Column clearance: approx. 1,050 mm – generous working area • Stroke: approx. 150 mm – efficient travel distance • Table size: approx. 1,000 × 1,200 mm – large clamping area • Table height above floor: approx. 850 mm – ergonomic working height • Hydraulic control (often with PLC/Siemens control) possible • Safety and UVV certification for manual loading – increased operational safety 💡 Thanks to its robust construction, this press is ideally suited for series production, drawing and forming processes as well as machining and assembly tasks in metalworking operations. ⸻ 📌 Features & Equipment • Two-hand operation / safety control • Adjustable mechanical stop • Pressure cut-off • Pressure switch • UVV-compliant safety features → all for efficient and safe operation on the shop floor Currently UVV-certified. ⸻ 🛠️ Applications This press offers versatile usage, such as for: • Metal forming / drawing work • Assembly and joining part production • Testing and quality control processes • Series and small batch production Ndsdjx Ry Nyepfx Alfja ⸻ 📦 Size & Weight • Dimensions (approx.): Width × Depth × Height ≈ 4.0 × 3.6 × 3.4 m • Weight: approx. 16 t – robust industrial construction

Condition: used, Year of construction: 1992, functionality: fully functional, stroke length: 300 mm, table width: 1,400 mm, installation height: 500 mm, • Type of machine: Hydraulic press / C-frame press • Manufacturer: Müller Weingarten (historic German engineering company) • Model designation: CKD 100 4.1 • Applications: • Forming, punching, pressing of metal or plastic components • Small and medium batch production • Tool and die making • Design: Robust H-frame or single-column construction, suitable for precise pressing and forming operations • Capacity: Typically around 100 t pressing force (number indicates approx. 100 metric tons nominal force—common for CKD models) 📐 Typical Features • Hydraulic drive: Precise control of force and stroke • Stroke range: Sufficient for versatile applications (e.g. drawing, bending, punching) Ndjdjx Ry Hrepfx Alfja • Stable construction: Designed for continuous industrial operation • Tool integration: Mounting options for custom tools and dies • Operation: Usually manual or semi-automatic, depending on year of manufacture 🧱 Typical Uses Hydraulic presses like the CKD series are used in production for: • Metal forming (e.g. bending, deep-drawing) • Assembling components by pressing • Assembly processes with defined force • Quality assurance and test pressing Complete circuit diagrams and documentation available! Inspection under power possible at any time.

Condition: used, Eccentric Press, C-Frame Press, Helmerding EH 35 B, Used Machine Manufacturer: Helmerding Type: EH 35 B Year of Manufacture: 1985 Weight: 2500 kg Technical Specifications: Press Capacity: 35 tons Stroke Length: 70 mm Table Dimensions: 600 x 450 mm Operating Modes: Continuous / Single stroke (Inching) Safety: Two-hand safety start control Ndjdpjy D Uhdefx Alfja Dimensions: Overall Dimensions: 1020 x 1600 x 2400 mm Additional Information: Note: The base plate (bed plate) is not included with the machine.

Condition: used, Year of construction: 2010, pressure 600 t distance between columns 3640 mm stroke fix 350 mm no. of strokes 11 - 44 /min dayligth (stroke and adjustment up) 1550 mm column travel -side 2200 mm table surface area 3600 x 2500 mm ram surface 3600 x 2500 mm ram adjustment 400 mm band width 2000 mm material thickness 0,6 - 2,5 mm material cross-cut 1600 x 2,5 mm² coil weight 35,0 t Number of Straightening rolls 13 0 straightening roll diameter 50 mm Ndjdpfx Aszrppcolfoa Blanking Line (press, coil line, blank stacking system) yom 1993 - 2010: new control Siemens S 7 - press Schuler type EBS 4-600 with infinitely variable drive, fly-wheel brake, pneumatic clutch/brake combination, hydraulic overload protection in ram, pneumatic counterbalance in ram, motoric ram adjustment, ram interlocking moving tables (2x) without rails for the moving tables - decoiler make Schleicher, type HE - 355 - 2100, yom 1994 with auxiliary drive, snubber roll - coil lifting device - extractor device make Schleicher - shear - straightening machine make Schnutz, type RME 18/50/13-2000 TZ, yom 1994 with infinitely variable drive, 30 intermediate rolls, 117 supporting rolls - coil loop bridge - roll feed make Schleicher, type WV-SYS-A 160-2000, yom 1994 - blank stacker NSM-Magnettechnik stored in dismantled condition - Video before dismantling available

Condition: good (used), Table press Storage number: Year of manufacture: 1986 Machine number: 599 Manufacturer: Robotron Dresden Press type: PETSe 0.5 Type: 2-column table press Ndjdpszvw R Asfx Alfea Table area: 280 x 280 mm Overhang: 55 mm Pressing force: 0.5 t Distance table – ram: 60 to 220 mm Stroke: approx. 10 to 20 mm Column passage: 90 mm Dimensions: 340 x 500 x 600 mm Features: Single and continuous stroke, 2-hand operation Condition: good, ready for use Weight: 69 kg

Condition: used, Year of construction: 1995, pressure 100 t stroke 20 - 120 mm no. of strokes 40 - 240 /min distance between columns 1300 mm dayligth (stroke and adjustment up) 670 mm column travel -side 400 mm table surface area 1200 x 800 mm hole in the table 900 x 200 mm table height over floor 1150 mm ram surface 1130 x 650 mm ram adjustment 80 mm material width 250 mm material thickness 0,3 - 3,0 mm material cross-cut 750 mm² Ndodezrpvcopfx Alfsa feed length 1 - 9999,9 mm power requirement 22,0 kW Weight 16,0 t dimensions (WxDxH) 3,7 x 2,5 x 3,7 m height over floor 3,7 m with infinitely variable PIV-drive, pneumatic clutch/brake combination (make Ortlinghaus), electronic press force monitoring (two channel), automatic stroke adjustment, motoric ram adjustment, pneumatic counterbalance in ram, motorised circular oil lubrication electronic roll feed (make Kaiser, type KWV 250)

Condition: used, Year of construction: 1977, pressure 250 t distance between columns 1110 mm stroke 250 mm Distance table/ram, max. stroke up, adjustment up 500 mm Table surface area 1100 x 900 mm Table height above floor 950 mm Ndjdpfx Aozrpthslfoa Side window 690 mm Ram surface 1100 x 900 mm Oil volume 730 l Power capacity 56,0 kW Dimensions (WxDxH) 2,3 x 1,55 x 3,96 m with oil-hydraulic drive, controllable dependent on pressure/time and way, cutting impact cushioning, depth stop No foundation pit necessary

Condition: used, Year of construction: 1985, pressure 40 t distance between columns 495 mm stroke 150 mm distance table/ram, max. stroke up, adjustment up 300 mm table surface area 490 x 400 mm hole in the table 50 mm table height over floor 950 mm side window 155 mm ram surface 150 mm speed down 200 mm/s speed up 200 mm/s working speed 20 mm/s oil volume 115 l power requirement 5,5 kW weight 2,2 t dimensions (WxDxH) 1,35 x 1,1 x 2,2 m Ndedpfszrptbox Alfsa with oil-hydraulic drive, upper and lower stroke limitation, mechanical depth stop, two-hand and foot operation

Condition: used, Year of construction: 1962, pressure 025 t Nodezrprqjpfx Alfjda throat 200 mm stroke 8 - 80 mm no. of strokes 180 /min distance table/ram, max. stroke up, adjustment up 330 mm table surface area 550 x 400 mm hole in the table 60 mm table height over floor 800 mm passage to the back 200 mm ram surface 355 x 220 mm ram adjustment 50 mm power requirement 2,7 kW weight 2,5 t dimensions (WxDxH) 1,2 x 1,8 x 2,4 m

Condition: used, Year of construction: 1982, pressure 150 t throat 520 mm stroke 30 - 200 mm no. of strokes 15 - 60 /min distance table/ram, max. stroke up, adjustment up 650 mm table surface area 1600 x 1000 mm hole in the table 1040 x 140 mm table height over floor 1000 mm passage to the back 1000 mm ram surface 1400 x 800 mm ram adjustment 120 mm power requirement 20,0 kW weight 27,5 t dimensions (WxDxH) 2,3 x 2,75 x 4,5 m with infinitely variable drive, pneumatic clutch/brake combination (make Ortlinghaus), hydraulic overload protection in ram, pneumatic counterbalance in ram, semi-automatic ram adjustment Nodpfezrprkox Alfeda