Used Hydraulic single column presses 26-50t for sale (34)

Condition: used, Year of construction: 1981, Installation height: 400 mm, Throat depth: 280 mm, Pressing force: 40 t, Hydraulic high-speed single-column drawing press, DUNKES type HZS 40 Machine # H 77-581, year of manufacture 1981 Technical data: Pressing force 40 t Cvpyxv3J9 Operating pressure 270 bar Stroke 150 mm Installation height 400 mm Projection 280 mm Rapid traverse from 400 mm/sec. Rapid traverse to 400 mm/sec. Pressing speed under full load 14 mm/sec. Table height 820 mm Table surface 600 x 515 mm Fold-through hole in table 100 mm diam. Drive power 7.5 kW Weight 3.1 t Oil filling 230 l External dimensions 850 x 1200 x 2390 mm With - cutting impact damping - Safety 2-hand control - self-holding with rapid traverse cut-off - Electric return stroke limiter - set-up tip circuit - Fully automatic work sequence - emergency stop - stepless power preselection - infinitely adjustable mechan. Depth stop - Switchover in the lower stroke range Stroke and time changeover Stroke and pressure changeover - separate hydraulics for die cushion used, in good condition

Condition: used, Year of construction: 1997, pressure 40 t throat 300 mm stroke 630 mm dayligth 900 mm table surface area 620 x 520 mm hole in the table 150 mm table height over floor 600 mm ram surface 150 mm total power requirement 15,0 kW weight of the machine ca. 4,5 t required space 1,0 x 1,9 x 3,0 m Uc0Yd2B0Iz permitted for manual loading according to the CE Regulations with oil-hydraulic drive, controllable dependent on pressure/time and way, two-hand operation press can be inspected in running condition in our warehouse

Condition: good (used), Norton 50T Downstroke Plate Frame Hydraulic Press • Press height 2750mm including pipework • Press Weight 1100Kgs • Max Press Load 50T • Max Hydraulic Pressure 428Kgs/cm2 • Ram Stroke Adjustable 610mm Max • Bed Height 762mm to Face of Bolster • Bed Area 610mm l-r x 406mm b-f • Oil Tank Capacity 70 lt. • Electric Motor Size 7.5Hp • Electrical Supply 415v 3 Phase • Overall Size Of press Unit 740 x 550 x 2750mm (WDH) • Ram End is 105mm Dia Plain End. Supplied with: • Machine Handbooks • *For sale with Jet Machinery Ltd* Jet Machinery Stock No: #78800 Ud7Oig2J7J Machine Serial Number: Not Visible Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Condition: new, Year of construction: 2024, Hydraulic press MECAMAQ / C-frame series / 40 tons / type (PCC40) Technical specifications: - 40T force, activated by 1 double-acting cylinder (Ø130/Ø80). - Dimensions of the lower plate 600x450mm, with "T" slots M12 (DIN650). - End of the piston rod mechanized for the attachment of Ø40x40mm tools. - Maximum opening 500mm. - Stroke of the hydraulic cylinder 250mm. - Outreach 250mm. - Hydraulic system with 2 speeds and automatic change of high speed by pressure activated by gear pumps. - Monitored hydraulic valves and hydraulic components installed on the machine according to hydraulic diagrams EN693 "Hydraulic system self-monitoring for hydraulic presses with downward stroke". - Maximum pressure of the hydraulic unit 300 bar. - Approach speed 28mm/s. - Working speed 7.5mm/s. - Retraction speed 45mm/s. Cyyxh2Xcwc - Motor power 4 HP (3ph. 400v 50Hz). - Stroke regulation by means of limit switches, with automatic retraction movement. - Pressure switch for maximum pressure regulation, with automatic retraction movement. - Activation of the machine by means of two-hand safety activation CAT.4. - LED lighting in the work area - Fixed side guard. - Machine color blue RAL5021 Scope of delivery: - User manual in ENGLISH with technical data for machine maintenance, machine in accordance with CE regulations. - The quoted price does not include any additional protective measures such as safety guards, fences, barriers, etc.; these must be taken into account depending on the location and specific working conditions.

Condition: good (used), Exner hydraulic press EE XSBR 200 Manufacturer: Maschinenfabrik Exner GmbH & Co KG, Germany Model: EE XSBR 200 Year of manufacture: December 1992 Cd9Bdk2U0I Machine number: 10313 Pressing force: 2000 kN Drive power: 63 kW Oil filling: 1850 liters Overtravel: 21 mm Safety distance: [value difficult to read] mm Weight: 27,000 kg Overrun time: 112 ms This robust and reliable hydraulic press from Exner offers a pressing force of 2000 kN and is ideal for demanding industrial applications. The machine has been well maintained and is in good working order. Due to its high performance and reliability, it is perfectly suited for heavy pressing work.

Condition: excellent (used), Year of construction: 1992, Pressing force: 30 t, I sell pneumatic press PRESSOTECHNIK PC 30-58, 30Ton, Perfect condition ! Cqyjlthreu

Condition: used, Installation height: 600 mm, Throat depth: 280 mm, Pressing force: 40 t, Table width: 520 mm, Table length: 620 mm, Hydraulic single-column press, DUNKES type HZ 40 Machine # H79-836 Year of construction 1979 Do3Bir Technical data max. pressing force 40 t stroke 400 mm Installation height 600 mm throat depth 280 mm Table dimensions 620 x 520 mm Table height 820 mm Safety distance 88 mm Oil pressure max. 280 bar Motor power 15 kW Weight approx. 4500 kg Dimensions approx. 1000 x 1500 x 2800 / 3700 mm With - two-hand release used, in good condition

Condition: used, Year of construction: 1996, pressure 40 t throat 330 mm stroke 250 mm dayligth 450 mm table surface area 800 x 500 mm hole in the table 100 mm E2Pmjau table height over floor 900 mm ram surface 100 mm feed down 406 mm/sec feed up 393 mm/sec feed under pressure 14 mm/sec oil volume 350 l total power requirement 7,5 kW weight of the machine ca. 4,6 t required space 1,3 x 2,3 x 3,4 m permitted for manual loading according to the CE Regulations with oil-hydraulic drive, controllable dependent on pressure/time and way, mechanical depth stop, two-hand operation press can be inspected in running condition in our warehouse

Condition: used, Hydraulic press, oil hydraulic press, pressing machine, pressing tool, pressing pliers -Hydraulic press: Hydraulic unit novopress type WK 9483 -Pressure: max. 150 bar / 0.45 l/min -with punch set: 1x Ø 18mm, 2x Ø 14mm, 1x Ø11 mm, 1x Ø 9mm -Operation: foot pedal -Connection hoses: for pressing tongs or similar -Dimensions: 850/550/H1250mm Jaq0Krn0G -Weight: 158 kg

Condition: good (used), Press machine, hydraulic press, used machine Bl2Fp8Cdko Manufacturer: SEJFO Model: 7051-3 Overall dimensions: 800 x 1400 x 2480 mm Weight: 996 kg Stroke length: 300 mm Maximum hydraulic pressure: 140 Bar Year of manufacture: 1997 Hydraulic power supply: 380 V; 50 Hz

Condition: good (used), Year of construction: 2002, Functionality: fully functional, Total height: 3,600 mm, Table height: 850 mm, Installation height: 500 mm, Total width: 1,200 mm, Total length: 1,500 mm, Throat depth: 250 mm, Pressing force: 50 t, Table width: 800 mm, Table length: 500 mm, Overall weight: 4,500 kg, Hydraulic C-frame press, capacity 50 to, table size 800x500 mm, stroke 500 mm, motor 22 kw, dimension 1200x1500x3600 mm, weight ca. 4500 kgs; 2-hand-operation, light-barrier-security B2Pqzpcpg8

Condition: excellent (used), Year of construction: 1975, Functionality: fully functional, Total height: 31,500 mm, Total width: 13,500 mm, Total length: 17,500 mm, Pressing force: 40 t, Table width: 1,000 mm, Table length: 500 mm, Operating speed: 200 mm/s, Overall weight: 3,200 kg, Reverse speed: 450 mm/s, Ram plate width: 450 mm, Ram plate length: 380 mm, Ram stroke: 500 mm, Distance between stands: 800 mm, Power: 15 kW (20.39 HP), PYE 40 SS hydraulic press with ejector. Year of production 1975, manufacturer VEB Wema Zeulenroda (Germany). Machine after general overhaul. Replaced piston seal. Parameters: Maximum pressing force 40 tons. Working pressure 16 MPa. Upper table 380 x 450 mm. Lower table 500 x 1000 mm. Ground clearance 800 mm. Cylinder stroke 500 mm. Down speed 200 mm/sec. Upward speed 450 mm/sec. Power requirement 15 kW. Weight 3200kg. Bhxals8Opm Height 3150mm, Length 1750mm, Width 1150mm. Technical condition of the machine very good. The machine after a general overhaul. It is possible to make a visual inspection and check the machine in motion.

Condition: used, Year of construction: 1977, Installation height: 350 mm, Throat depth: 280 mm, Pressing force: 50 t, SCHÖN hydraulic single-column press type UTE-BC Serial # 1619 Year of manufacture 1977 Technical data max. pressing force 50 t stroke length 150 mm Table size 550 x 750 mm drop opening 80 mm Bear size 500 x 300 mm throat depth 280 mm Installation height 350 mm Passage width to the rear 150 mm Drive power 7.5 HP Dimensions L x W x H 1300 x 1400 x 2400 mm Weight approx. 2000 kg With - adjustable holding time - Blow-out device - Inching operation - light barrier Buolgyet used, from an operational resolution

Condition: used, Year of construction: 1991, pressure 40 t stroke 150 mm throat 420 mm dayligth 450 mm table surface area 700 x 820 mm table height over floor 850 mm ram surface 600 x 600 mm feed down 370 mm/s feed up 370 mm/s working feed 18 - 33 mm/s E2Pmi0M oil volume l power requirement 8,0 kW Weight 5,0 t dimensions of the machine ca. 1,1 x 1,9 x 2,4 m permitted for manual loading according to the German Safety Regulations (UVV) with oil-hydraulic drive, controllable dependent on pressure/time and way, cutting impact cushioning, mechanical depth stop, two-hand operation

Condition: good (used), Brand: LIZUAN Model: 27.5TN Force max. Dimmable 27,5 kn Maximum adjustable stroke: 200 mm Working speed: 80 mm/s Reverse speed : 175 mm/s Light between table and holder : 480 mm Electric motor power: 4 kw B7Moa033J8 Oil tank capacity: 58 l

Condition: used, Year of construction: 2023, Press capacity: 30 ton Stroke: 400 mm Daylight: 500 mm Table surface area : 500 x 500 mm Slide area: 500 x 500 mm Table height over floor: 850 mm Approach speed: 100 mm / sec Working speed: 10 mm / sec Return speed: 150 mm / sec Cjlxlqfo7S Required power: 7,5 kW Dimensions L x W x H: 1500 x 1400 x 2600 mm Weight of machine approx.: 2,5 ton

Year of construction: 1954, Condition: used, Hydraulic press, single-column press, C-column press, oil-hydraulic press, hydraulic single-column press -Manufacturer: Müller, hydraulic single-column press type HEP15 -Pressing force: 15 tons -Clamping table: 900 x 500 mm -Projection: 265 mm -Max. Stroke: 430 mm -Operation: foot pedal Eqw3Dfsau -Motor: Siemens 4.0 kW -Dimensions: 1450/900/H2300 mm -Weight: 1646 kg

Condition: excellent (used), Year of construction: 1990, Functionality: fully functional, Total height: 29,500 mm, Total width: 11,500 mm, Total length: 17,500 mm, Pressing force: 40 t, Table width: 630 mm, Table length: 500 mm, Operating speed: 110 mm/s, Overall weight: 3,000 kg, Reverse speed: 450 mm/s, Ram plate width: 450 mm, Ram plate length: 380 mm, Ram stroke: 500 mm, Distance between stands: 800 mm, Power: 13 kW (17.68 HP), PYE 40 S1/M hydraulic press. Year of manufacture 1989. manufacturer VEB Wema Zeulenroda (Germany). Machine after general overhaul. Replaced piston seal. Parameters: Maximum pressing force 40 tons. Working pressure 16 MPa. Upper table 380 x 450 mm. Lower table 500 x 630 mm. Ground clearance 800 mm. Cylinder stroke 500 mm. Down speed 100 mm/sec. Upward speed 450 mm/sec. Power requirement 13 kW. Weight 3180kg. Height 2950mm, Length 1750mm, Width 1150mm. Technical condition of the machine very good. The machine after a general overhaul. It is possible to make a visual inspection and check the machine in motion. Dpblvl

Condition: used, Year of construction: 1989, Installation height: 500 mm, Pressing force: 44 t, Table width: 600 mm, Table length: 500 mm, Pneumatic single-column press (C-shape) TOX Pressotechnik type S50.4.80.6 / PC 50 Year of manufacture 1989 Technical data: Pressing force 440 kN / 44 t Total stroke 80 mm of which power stroke 6.0 mm Compressed air connection 6.0 bar Table size 596 x 496 mm Installation height 500 mm Fold-through hole 120 mm With - Press frame PC 50 - Power pack S50.4.80.6 - 2-column guided ram plate - Underframe U 50 E2Muxry - Protective cover SH 50 - Press control ST 03 3/4" - Set-up mode = additional equipment used, in very good condition

Condition: used, Year of construction: 1981, pressure: 30 t distance between columns: BxT: 600/450 mm stroke: mm daylight dimension : table/slide up: 650 mm ram stroke: ca. 600 / highspeed strokes mm table surface area: LxB: 500 x 700 x Ø 60 mm surface area of ram: 650 x 800 mm hydraulic-pressure: 170 bar air pressure - required: 4 - 6 bar total power requirement: 11 kW weight of the machine ca.: ca. 2,0 t dimension machine xH: 1,26 x 1,75 x 3,4 m Four-column press, hydraulic Possible applications: can be used as a deburring press Further technical features: - Table aperture 200x250mm - Opening in ram Ø 160mm - Passage in the column width 600 and depth 450mm - Operation via control panel Equipment: - Protective grille - Base plates 7Njvktcdr

Year of construction: 1985, Condition: good (used), Met International Used Hydraulic press Forming press Beedveu 40ton Bed size 600mm X 600mm Four poster hydraulic press. H frame / C frame also available. Many other used presses for sale with cushion, different daylight and stroke. New hydraulic power presses available built to your specification. Cheap hydraulic presses. Large and small bed sizes available. Delivery and installation can be arranged.

Condition: used, Year of construction: 2022, Machine/vehicle number: 3413, Press capacity: 50 ton Throat depth: 265 mm Stroke: 250 mm Daylight: 400 mm Table surface area : 700 x 450 mm Slide area: 550 x 300 mm Table height over floor: 850 mm Approach speed: 32 mm / sec Working speed: 6,3 mm / sec Return speed: 42 mm / sec Cgoanuivo0 Required power: 4 kW Dimensions L x W x H: 1290 x 1160 x 2085 mm Weight of machine approx.: 1,75 ton

Year of construction: 1970, Condition: used, Machine/vehicle number: 12469, Hydraulic press, single-column quick-cycle press, C-column press, oil-hydraulic press Ql8Hk83Se - Press force ram: 40 to -Clamping table: 800 x 560 mm -Insertion height: 750 mm - Projection: 300 mm -Max. Stroke: 350mm -Operation: two-handed -Dimensions: 1700/1350/H3200 mm -Weight: about 5000 kg

Year of construction: 1991, Condition: used, pressure: 40 t distance between columns: mm stroke: mm daylight dimension : table/slide up: 450 mm throat: 375 mm ram stroke: max. 300 mm Table dimensions: 900 x 500 x 85 mm passage inside table: Ø 120 mm height over floor: 900 mm total power requirement: 15,0 kW weight of the machine ca.: 5,8 t dimension machine xH: 2,3 x 1,45 x 2,40 m Yo9I0 further technical data: -size of the ram plate W: 900 x D: 500mm -pivot hole in ram Ø 40 x 75mm -Hydraulics: tank capacity approx. 500Liter; operating pressure 275 bar; pump capacity 22,9 l/min. Two-hand operation and/or control panel

Year of construction: 1960, Condition: used, pressure: 30 t distance between columns: 320 mm stroke: 600 mm throat: 320 mm Table dimensions: 700x500 mm daylight dimension : table/slide up: 600 mm total power requirement: ca. 4 kW weight of the machine ca.: 2,5 t dimension machine xH: 1,5x0,5x2,4 m - Machine control via foot pedal. - Speed adjustable via foot switch. Machine can be demonstrated under power. Duppzq (Accident prevention regulations was valid until 2011)