Used straightening-, and bending machines for sale (54)

Condition: used, Technical details: Pressure: 2,5 t throat: 155 mm max. ram stroke: 280 mm Dcelhceu Nfv Uocqlec distance table/ram: 450 mm clamping plate on table: 260 x 1000 mm ram speed - forward: 0,08 m/s ram speed - reverse: 0,32 m/s mortise hole in ram: Ø 20 x 45 mm height over floor: 930 mm total power requirement: 1,1 kW weight of the machine ca.: 500 kg dimension machine xH: 0,85 x 1,0 x 17 m The machine is equipped for straightening work. *

Condition: good (used), Year of construction: 1991, Hydr.horizontal straightening and bending press Pressure capacity max.160 t Dcslhcecffzaecqljc MAE Type:HY RI 160 RH Year.1991. For more data see data sheet.

Condition: used, Hydraulic Horizontal Straightening Press, Horizontal Press STENHOJ Type 40 Horizontal hydraulic press for straightening work on steel beams or welded structures Serial no. 42615 Year of manufacture: 1984 Refurbished in 2025 Pressing force: 40 tons Ram stroke: 300 mm Piston rod diameter: 80 mm Working height: 780 mm (floor to center of piston rod) Table size without pressure pads: approx. 1000 x 290 mm Installation dimension, ram + press block to counter bearing: 260 mm (with pressure pads on ram and counter bearing) Installation dimension, ram without press block to counter bearing: 440 mm (without pressure pads on counter bearing) Height of the two adjustable pressure pads: 130 mm Pressure pad width: 220 mm Advance speed: 10 mm/s Return speed: 20 mm/s Hydraulic tank capacity: approx. 60 liters Motor power: 3 kW Power supply: 400 Volt, 50 Hz - Cylinder stroke operated manually via an actuation lever, sensitive control via mechanical control valve - Pressing force readable via pressure gauge - Ram stroke position with actual value display, digitally readable, ideal for precise repeatability of pressure points during straightening - 2 adjustable counter bearings via threaded spindle (centric parallel adjustment from 290 to 890 mm) Djlhcoydqd Hjcqlscc - Straightening tools with rounded pressure faces - Infeed rollers for material support, centrally height-adjustable via handwheel (roller width = 250 mm) Required space (L x W x H): 170 x 140 x 100 cm Weight: 1250 kg In excellent condition

Condition: new, pressure 20 t stroke max. 200 mm Djlhcetq Du Recqlocc bending capacity max. - flat 200 x 10 mm working feed 10 mm/sec Control NC Height of Toolings 150 mm total power requirement 2,2 kW weight of the machine ca. 640 kg required space 600 x 1100 x 1220 mm The Gerd Wolff HP 20 is a hydraulic horizontal press machine with many many possible combinations. Whether it is the bending of tubes, the punching of profiles or the cutting of sheet metal - with the right accessories, the HP 20 is a multifunctional machine among the presses. Standard accessories - ergonomic tool clamping table - easy tool change - hydraulic speed and pressure adjustment - easily adjustable back gauge - induction hardened support pins - NC control Highlights - control panel with digital display - Easy tool change - hardened support pins - hydraulic speed regulation The HP 20 is manufactured for our sales brand "GERD WOLLF Maschinenfabrik", by a renowned manufacturer from Türkiye.

Condition: new, pressure 40 t stroke max. 300 mm bending capacity max. - flat 250 x 16 mm working feed 10 mm/sec Control NC Height of Toolings 250 mm total power requirement 4 kW weight of the machine ca. 1190 kg required space 650 x 1250 x 1300 mm The Gerd Wolff HP 40 is a hydraulic horizontal press machine with many many possible combinations. Dcsljuddfbshccqljc Whether it is the bending of tubes, the punching of profiles or the cutting of sheet metal - with the right accessories, the HP 40 is a multifunctional machine among the presses. Standard accessories - ergonomic tool clamping table - easy tool change - hydraulic speed and pressure adjustment - easily adjustable back gauge - induction hardened support pins - NC control Highlights - control panel with digital display - Easy tool change - hardened support pins - hydraulic speed regulation The HP 40 is manufactured for our sales brand "GERD WOLLF Maschinenfabrik", by a renowned manufacturer from Türkiye. The pictures are for orientation only and are not true-to-scale representations of the machine.

Condition: new, pressure 60 t stroke max. 300 mm bending capacity max. - flat 300 x 16 mm working feed 10 mm/sec Control NC Height of Toolings 300 mm total power requirement 5,5 kW weight of the machine ca. 1530 kg The Gerd Wolff HP 60 is a hydraulic horizontal press machine with many many possible combinations. Whether it is the bending of tubes, the punching of profiles or the cutting of sheet metal - with the right accessories, the HP 60 is a multifunctional machine among all presses. Standard accessories - ergonomic tool clamping table - easy tool change - hydraulic speed and pressure adjustment - easily adjustable back gauge - induction hardened support pins - NC control Dcslhexfb Ikjccqloc Highlights - control panel with digital display - Easy tool change - hardened support pins - hydraulic speed regulation The HP 60 is manufactured for our sales brand "GERD WOLLF Maschinenfabrik", by a renowned manufacturer from Türkiye. The pictures are for orientation only and are not true-to-scale representations of the machine.

Condition: excellent (used), Year of construction: 2010, functionality: fully functional, Used straightening press in very good condition for sale. This universal and robust Stierli straightening press has a 5m straightening beam. It can process beams up to HEA-600 and HEB-600 (with S-235). The machine is operated with the proven Stierli stroke fine adjustment control. It is therefore very easy to operate and allows fast, precise straightening and bending. Additional options can also be added on request, e.g. driven roller conveyor, NC control, laser measurement etc... Deleufhzvehccqlscc (Note: The photo does not correspond to the original image)

Condition: new, Year of construction: 2025, pressing force: 20 t, 20 T Single-Column Straightening Press (DCS-20) TECHNICAL DATA (MODEL – DCS-20) DESIGN Pressing capacity – 5–20 t (adjustable) Maximum installation height – 700 mm Table usable surface – 500 x 600 mm Ram usable surface – 500 x 600 mm Frame type – C-frame Table height from floor – 800 mm Overall dimensions approx. (W x D x H) – 1,150 x 1,250 x 2,469 mm Total weight approx. – 1,900 kg T-slots – according to DIN 650 (18 mm) or machined to customer specification HYDRAULIC CYLINDER Piston stroke – 0–500 mm (adjustable) Cylinder diameter – Ø 100 mm (1 unit) Piston rod diameter – Ø 60 mm (1 unit) Max. working pressure – 250 bar Return speed – 50 mm/s Idle speed – 25 mm/s Pressure build-up time with closed tool – max. 2 s (steel on steel) HYDRAULIC UNIT Hydraulic pump – REXROTH, 11 l/min (1 unit) Motor power – 4 kW (1 unit) Pressure accuracy during pressing stroke – ±5 bar Oil tank capacity – 150 l Mounting – Hydraulic unit installed at the top rear of the press Hydraulic manifold and valves – HYDROPACK Air filter and oil filter – FILTREC Oil level – electronic oil level switch ELECTRICAL CONNECTION Main supply – 400 V AC Control voltage – 24 V DC Dcelhcceyghvfeqloc Frequency – 50 Hz Hydraulic main motor connection – 4 kW Total connected load approx. – 4 kW

Condition: good (used), Year of construction: 2011, Pressure 160 t Total power requirement 18.5 kW Dcjlhceyg E Sqecqloc Machine weight approx. 13.5 t

Year of construction: 1984, condition: used, Printing machine, embossing machine, stamping machine -without function, control: defective Dcolhccqjd Hp Tzsloc -pneumatic-hydraulic press - Stroke: 50mm - clearance between columns: 850 mm -Table surface: 400 x 370 mm -Dimensions: 1285/590/H1820 mm -Weight: 416 kg

Condition: good (used), Profile bending machine, bending machine, flat bar bender, horizontal bending/straightening press -Flat bar bender: hydraulic profile bending machine -Base: on casters, table folds on both sides -Operating mode: Manual and automatic operation -Accessories: see photos Dcjlhjh Tk Dasccqloc -Overall dimensions: 2155/1320/H1070 mm -Transport dimensions: 1320/840/H1245 mm -Weight: 404 kg

Condition: good (used), Hydraulic press, bending machine, straightening machine, profile straightening system, strip straightening machine, strip straightening device, shaft straightening system, combined bending machine-straightening press, profile bending machine, bending machine, flat iron bender, horizontal bending/straightening press, horizontal bending machine Doljvgu Haohccqlocc -Hydraulic press: Straightening system Straightening machine Profile straightening system with roller conveyor -Pressure force: 10 ton -Pressure: max 100 bar -Roller conveyors: 2x 1000/170/H1110 mm / rollers Ø 56 x 140 mm -Transport dimensions: 1335/1220//H1470 mm -Weight: 807 kg

Year of construction: 2006, condition: used, Printing machine, embossing machine, stamping machine, rail stamping machine, embossing press, die cutter, pneumatic die cutter -Manufacturer: Stommel 6 Voos, embossing press, rail stamping machine on a solid base -Type: SV700/6/PE/EF -Band width: 13 mm, convertible -Individual components: see photos -Accessories: without other accessories -Dimensions: 820/520/H1680 mm -Weight: approx. 154 kg Dolhcekyy Ufocqlocc

Condition: new, bending radius min. 190 mm Dcelhccqjxcuyheloc square edge steel 20 x 20 mm flat steel 100 x 7 mm round bar steel 22,0 mm L-beam 100 x 10 mm range L-W-H 900 x 430 x 310 mm weight of the machine ca. 33.0 kg. properties - For precise cold and hot bending of flat, round and square steels - Stable construction for screwing onto the workbench - Infinitely adjustable bending stop - With eccentric quick release for efficient work - Readable bending angle up to 120 ° - High repeat accuracy thanks to the bending angle stop - Ideal for repair shops and locksmiths scope of delivery - Bending plate - Stepless angle stop - Terminal block with eccentric clamp - Material stop

Condition: new, square edge steel 16 x 16 mm flat steel 100 x 5 mm L-beam 60 x 8 mm bending radius min. 190 mm round bar steel 18,0 mm weight of the machine ca. 33,0 kg. Dceloxcux Rshccqlec Characteristics : - For precise cold and hot bending of flat, round and square steel - Stable design for screwing on the workbench - Infinitely adjustable bending stop with locking pin - With eccentric quick clamping for efficient work - Readable bending angle up to 120° - High repetition accuracy thanks to the bending angle stop - Ideal for repair shops and locksmiths Scope of delivery: - Bending plate sharp / round - Radius bending plate R 20 / R 25 - offset block - Bending plate for round bar - offset plate - Radius bending plate R 10 / R 15 - angle stop - Clamping block with eccentric clamp - Material stop

Condition: excellent (used), Year of construction: 1970, pressure 6 t throat 250 mm Dolhccqovpaadslscc stroke 550 mm table surface area 650 x 500 mm weight of the machine ca. 3,5 t dimensions of the machine ca. 1,2 x 1,0 x 2,8 m

Condition: good (used), Profile bending machine, bending machine, flat iron bender, horizontal bending/straightening press Dcslhccot Hmhljqlec -Bending/straightening press: hydraulic profile bending machine -Base: solid construction, mobile -Hydraulic unit: unfortunately without type designation -Piston rod: Ø 55 mm / stroke: 200 mm -Individual components: see photos -Total dimensions: 1180/1060/H1000 mm -Weight: 445 kg

Condition: like new (used), functionality: fully functional, total height: 2,900 mm, table length: 10,000 mm, total width: 3,660 mm, total length: 10,200 mm, table height: 900 mm, table width: 2,545 mm, pressing force: 100 t, overall weight: 26,000 kg, operating speed: 9 mm/s, reverse speed: 14 mm/s, pressure: 320 bar, power: 4 kW (5.44 HP), MOBILE HYDRAULIC GANTRY PRESS WITH MOVABLE HEAD AND 10-METER LONG TABLE FOR STRAIGHTENING WELDED STRUCTURES AND CUT PLATES TECHNICAL DATA Force T 100 Motor power kW 4 Motor ventilation switch power kW 0.37 Bridge travel motor power kW 0.75 Working speed mm/s 3 Approach speed mm/s 9.2 Return speed mm/s 14.4 Max. pressure Bar 320 Working area mm 10,000 x 2,545 Djlhcjwkvmnjcqlecc Ram stroke max. mm 450 Maximum open height mm 600 Lateral travel mm 2,120 Gantry travel mm 9,140 Working height mm 900 Total length mm 10,200 Total width mm 3,660 Height mm 2,900 Weight kg 26,000 The hydraulic press TL-100/10000E belongs to the T/NC series and has been specially developed for straightening welded structures and cut plates. As with all hydraulic presses in this series, its design facilitates the loading and unloading of large workpieces. Thanks to the lateral movement of the cylinder and the longitudinal travel of the bridge, access to various pressing points is possible without having to reposition the workpiece. The machine complies with all essential safety and health requirements in accordance with CE regulations. STRUCTURE AND TABLE • Electrically welded structure made exclusively from S355JR steel. • Stabilized and machined after welding to ensure perfect parallelism and precision. • Calculated and designed using finite element software. • Longitudinal bridge travel achieved by frequency inverter and toothed belt. • Motorized lateral head movement. CYLINDER AND HYDRAULIC UNIT • Double-acting cylinder with lapped sleeve, chrome-plated piston, and maintenance-free wear-resistant guides. • Fitted with a removable and exchangeable pad to prevent piston wear and machined at the end to match the tool. • Includes standard anti-rotation device for the cylinder and a calibrated front end with limit switches for stroke adjustment. • Motorized hydraulic unit with two speeds and automatic cut-off for rapid speed. • Cylinder decompression valve. • Pressure regulator. • Glycerin pressure gauge with tonnage indicator. ELECTRICAL INSTALLATION AND SAFETY • The control panel includes a selector switch for manual or semi-automatic operation. • Selector switch for choosing between rapid approach speed and slow working speed. • Operation via pendant control with emergency stop and low-voltage control. • Includes button to confirm a cycle.

Condition: new, Year of construction: 2025, functionality: fully functional, machine/vehicle number: SH-250, total height: 1,700 mm, total width: 2,000 mm, total length: 3,000 mm, pressing force: 250 t, operating speed: 4 mm/s, reverse speed: 8 mm/s, stroke length: 450 mm, Equipment: documentation/manual, MODEL: SH-250 Djljwk Hkqehccqlocc STANDARD DESCRIPTION: Our SH series horizontal hydraulic ram press is engineered with a range of three different capacities, from 100 to 250 tons. These horizontal hydraulic presses are specifically designed for straightening and bending profiles, bars, and beams. The horizontal configuration enables easy handling of large-size beams and profiles. The latest-generation HS series offers versatile utility, with the possibility to fit a wide variety of tooling. They operate at a hydraulic pressure below 350 BAR to ensure greater durability of the entire hydraulic system. STRUCTURE AND TABLES The SH series horizontal straightening hydraulic presses feature an electro-welded "C"-frame structure made exclusively from S355JR steel. The frame is stabilized and machined after welding to ensure perfect parallelism and precision. Design and calculation are carried out using finite element software, thus maintaining our high standards of robustness, accuracy, and quality. They come equipped with a main anti-rotation push cylinder and a rear support table, both made from high-strength steel and machined with DIN 650 T-slots. Standard equipment includes C45E steel support blocks. Two adjustable side rollers are also included as standard, one on each side. CYLINDER AND HYDRAULIC UNIT Double-acting cylinder with honed sleeve, chrome-plated piston, and maintenance-free anti-wear guides. Cylinder is operated by a lever hydraulic distributor. It is fitted with a removable block to prevent piston damage. Single speed motor-driven hydraulic power unit. ELECTRICAL INSTALLATION AND SAFETY Electrical system includes a motor protection switch and emergency stop. Supplied with a glycerine-filled pressure gauge (tonnage readout) and hydraulic oil. Fully complies with all essential CE safety and health regulations. Supplied with an operation manual. OPTIONAL ACCESSORIES • Basic feed rails from 3,000 mm up to 12,000 mm, height adjustable. • Motorized feed rails from 3,000 mm up to 12,000 mm. • Hydraulic elevation and tilting of feed rails. • 415 mm folding device. PROMECAM clamping system. • Additional single-speed manual pump, allowing both manual and powered operation. • Low-voltage electric foot pedal control. • Precision limit switches with cylinder anti-rotation system and low-voltage electric foot pedal control. • Two-speed hydraulic power unit. • Geometry customized to your requirements.

Condition: good (used), Year of construction: 2007, Marca: SCHIAVI Modelo: HFBs 100/ 3 Nominal capacity: 100 tons Table length: 3110 mm Work table width: 90 mm Working height without rise: 910 mm Maximum distance between tables: 450 mm Maximum nominal stroke: 250 mm Gooseneck depth: 405 mm Distance between uprights: 2700 mm Maximum pressure: 303 MPa Djlhjxaz Igsccqlocc Oil capacity: 126 dm³ Maximum length (footprint): 4000 mm Motor power: 7.5 kW

Condition: used, Technical details: Dcelhceu Nfrpecqloc pressure: 200 t stroke: ca. 200mm mm table surface area: L:1200xH:450 mm jaw width: 1000x200 mm total power requirement: 18 kW weight of the machine ca.: 15 t dimension machine xH: 4,5x1,5x2,2 m Beam - Straight Bending Machine - electric box (LxWxH:0,85x0,8x2,7m) - chuck intake: LxW 1200x220mm - chuck adjustment 200mm moveable - opening width of chucks 300mm - manual control accessories: - div. limit stops, tools, try square and marking gauges i.D. *

Condition: used, Year of construction: 2008, Technical details: Dcolsw Ng D Tshccqloc pressure: 6 t stroke: 1020 mm total power requirement: 3,5 kW Can only adjust between tips *

Condition: used, Year of construction: 1991, weight of the machine ca. 1,5 t Delhjx Ni E Ijccqlscc ja

Condition: used, Year of construction: 2005, pressing force: 1,600 t, workpiece weight (max.): 25 kg, We offer directly on behalf of the owner : Djlhex Tvcneccqljcc Make : Graebener Maschinentechnik Type : GRNM Year of construction : 2005 Bending force max.: 16.000 kN ( 1.600 t ) Tool length : 1.600 mm Data at 520 N/mm2 Tube diameter max.: 1,524 mm Tube diameter min.: 457 mm Sheet thickness max.: 40 mm Tube length max.: 13.2 m Tube length min.: 6 m Max. pipe weight: 25 t Total power req. approx.: 245 kW / 400 V / 50 Hz Space requirement approx.: 27 x 3 m Further technical data and photos available on request or see at pictures / PDF The machine was built in 2005, worked until 2021 and was professionally dismantled and packed for transport.

Condition: used, Used Mario Riboldi Press Brake Model: HL 150/80 Description: • Mario Riboldi hydraulic press brake, ideal for medium to heavy metal fabrication work. Technical Data: Delhccex Sxymoqlecc • Bending force: 150 tons • Useful working length: 8,050 mm