Used Gear honing machines for sale (3)

Condition: used, Year of construction: 2005, Technical details: workpiece diameter: 63,5 mm centre distance: 350 mm honing length max.: mm total power requirement: kW weight of the machine ca.: 6 t dimensions of the machine ca.: 2,70x2,30x2,60 m Technical data G0504 working space Length of the clamping surface mm 1550 Number of T-slots mm 2 Width of the T-slots mm 18 Distance between T-slots mm 180 Center height (tailstocks) mm 350 Swivel range of the fine wheel head (U-axis) degrees + 30 / -30 Center distance - tailstock / fine wheel min./max. mm 120/225 Input resolution (all NC axes) mm / degrees 0.001 Delivery slide Movement range (= Z-axis travel) mm 105 Input resolution mm 0.001 tool Outside diameter min./max. mm 225/275 Hole diameter mm 160 Width mm 60 workpiece Outside diameter min./max. mm 40-150 Module min./max. mm 1.25-4.0 Tooth width max. Mm 45 weight Weight of the machine approx. Kg 5500 Operating fluid requirements Cooling lubricant recommendation, see chap. 8th Hydraulic fluid HLP D 46 approx. Itr 100 Kljlevnmn Sehcdw Dep Speeds and feeds Tool speed (continuously adjustable) max. 1 / min 2000 Feed rates Rapid traverse / feed Z direction up to m / min 2 X direction up to m / min 2 U-direction up to m / min 2 V-direction up to m / min 2 C3 direction ree / sec 12 Electrical equipment Operating voltage V 400 Control voltage / lighting voltage V DC / AC 24/230 Frequency Hz 50 Power requirement approx. KVA 27 If the electrical installation has to be carried out according to customer specifications, only the information in the electrical documentation applies. Motor data Servo drives: Nm 1 / min Tool drive C1 27.0 3000 Workpiece drive C2 27.0 3000 X-axis 20.0 3000 Z-axis 20.0 3000 U-axis 6.0 3000 Vertical portal (V1 axis) 6.0 3000 Portal horizontal (U1 axis) Gripper axis of rotation C3 5.0 3000 Loading slide (X1 axis) 5.0 3000 Three-phase motors: KW 1 / min Hydraulic motor 1.5 1410 Central lubrication 0.07 2700 Coolant pump 4 2840 Hydraulic equipment Delivery rate Itr / min 21 System pressure bar 50 Clamping pressure for: headstock max. Bar 35 Clamping tailstock min./max. bar 20 Only available if required. Not all limit values ??can necessarily be reached at the same time. If several maximum values ??come together in a processing task, performance restrictions must be expected! We reserve the right to make changes to the specified constructions, dimensions and weights *

Condition: used, Year of construction: 1983, workpiece diameter 250 mm centre distance 0 mm honing length max. mm max. module 5 Gear Ø, min./max. 10 / 250 mm Module range 1 - 5 Length of teeth / max. table stroke 500 mm Height of centres of tailstocks 220 mm Max. weight of workpiece 50 / 100 kg Kelet Hwzpohcdw Djlp Honing head swivelling +/- 35 ° Speeds of honing tool 20 - 500 rpm Size of honing tool, Ø x width 300 x 40 mm Workpiece speeds 500 - 3,000 rpm Total adjustment of cross slide 270 mm Rapid traverse of cross slide 50 mm Infeed travel of cross slide, mechanical 1 - 8 mm/Ø Roughing / finishing infeed 1 - 29 / 0.2 - 2.8 mm/sec Table speeds, hydraulic 0 - 6 m/min Total electrical load 5.5 kW - 380 V - 50 Hz Weight 3,200 kg Accessories / Special Features * Working parameters can be preset using counters and control units. Automatic working process with workpiece counter. * All roughing and finishing infeeds can be adjusted by a decade switch; as well as by table reverse times and fast infeeds with preset times (1sec = Ø 0.04 mm), set on a potentiometer. Ampere display, etc. * Convex honing and conical honing are possible via templates. Asymmetric honing is also possible if the workpiece is prepared appropriately (i.e. pre-shaped). * Separate honing oil unit with magnetic separator and fine filter. * Mechanical tailstocks for manual loading. * Oil mist separator. * Sliding doors with foot switch. * Separate hydraulic unit. Condition : Good. Machine can be inspected under power. Delivery : Ex stock, as inspected. Payment : Net, after conclusion of contract. We have a large selection of gear machines available. Please let us know your requirements.

Condition: used, Year of construction: 1996, workpiece diameter 240 mm centre distance 0 mm honing length max. 500 mm max. module 5 total power requirement 12 kW weight of the machine ca. 5000 kg Klelhot Hwvmjcdw Dop dimensions of the machine ca. m