Condition: used, Year of construction: 2001, Continuous press Manufacturer: Ligmatech Type: Optimat MDE 10 Year of manufacture: 2001 Technical data Body dimensions - Length: 300 - 2500 mm - Height: 300 - 1300 mm - Depth: 120 - 600/800 mm - Pressing forces are generated electrically, both horizontally and vertically, and can be varied independently - Pressing forces are applied vertically via a pressure plate and horizontally via 3 pressure jaws each - Pressing takes place centered and on a zero line on the operator side Iedpfxszuzxbj Ah Ujtl Positioning of the pressure jaws: - Top pressure jaw with forced guidance on the top press, optionally lowerable via cylinder - Middle pressure jaw freely programmable and motor-driven - Bottom pressure jaw freely programmable and movable via a common drive with the middle pressure jaw Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2017, Automatic cold press Manufacturer: CMB Type: PFR-CCL Year of manufacture: 2017 Technical data: Motorized loading table 3,500 x 1,600 mm for manual assembly of the plates and automatic loading into the press on the 1,600 mm side. Structure made of welded steel profiles. Devices for adjusting the working height to compensate for unevenness in the floor. Steel rollers. Foot switch. PRESS Plate size: 5,500 x 1,600 mm Loading side: 1,700 mm Stroke: from top to bottom Opening: 450 mm Cold press The plates are made of steel sheet and attached to a steel frame structure. Maximum pressing force: 160 tons. Specific pressure (on 100% of the area): 1.82 kg/cm2 Specific pressure (on 80% of the area): 2.27 kg/cm2 Pressure cylinder: 12 x 80 mm Auxiliary cylinders: 6 x 50/30 mm Power supply: 400 Volt EU/50 Hz/3 PH. + G AUTOMATIC LOADING and UNLOADING of the plates on the lower plate, on the 3,500 mm side. The transport is carried out via a motorized MYLAR belt. The belt is activated by 2 rollers, one of which is located at the entrance and one at the exit of the press. The rollers are driven by a motor with a chain that slides on special guides. The Mylar belt rotates around the lower plate, which rests on special side supports. The belt rotates on 2 rollers, which are located at the entrance and exit of the press. Itodpfxszuzw De Ah Uel The ends of the MYLAR belt are attached to special rods with devices for tensioning the MYLAR. The upper plate is covered with a Mylar film. The press plates consist of thick steel sheets that are welded to the frame structure. HYDRAULIC UNIT with pump, oil tank and valves for operating the pressure cylinders and auxiliary cylinders that move the upper plate. The hydraulic control unit is located in the upper part of the press to facilitate maintenance. CONTROL PANEL with buttons and switches. Pressure control manometer on the front of the press. UNLOADING MOTORIZED ROLLER TABLE 2,000 x 1,600 mm The unloading table is located at the exit of the press for manual unloading of the pressed plates. Exit side from the press: 1,600 mm. Note: The loading table of the press with the dimensions 3,500 x 1,600 and the unloading table with the dimensions 2,000 x 1,600 are shorter than the press table with the dimensions 5,500 x 1,600, as the press was installed in a line. Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1996, Continuous press Manufacturer: OTT Type: 300-K-D0 Itedpfx Ahozuzwwj Uel Year of manufacture: 1996 Technical data Plate dimensions: 2550 x 1350 mm Hot water heating 6 pressure cylinders Total pressing force: 135 t Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 2007, Lamination press Manufacturer: Dimter Type: PROFIPRESS L2500 Year of manufacture: 2007 Technical data Wood dimensions to be processed Wood width, panels: 30 - 150 mm Wood thickness: 11 - 60 mm Wood inlet length: 800 - 2500 mm Panel widths, variable: max. 1300 mm Specific pressing pressure for cross-sections of 2500 x 60 mm: up to 1.6 N/mm2 The pressing surface per press cycle must not be smaller than 100 cm2 Filling width of the press per cycle: min. 650 mm / max. 1300 mm Max. filling area of the press per cycle: 3.25 m2 (The max. usable press width depends on the widths of the individual lamellas.) Wood type Softwood/hardwood Press without options Electrical connection, press: 7 kW Electrical connection, 40 kW generator: 56 kW Operating voltage: approx. 400 Volt / 50 Hz (C/s) Collection table extended to 3700 x 1300 mm, with stainless steel wood support Motor-driven multi-function slider Lamination press Profipress L 2500 Press bed area approx. 2500 x 1300 mm Sturdy base frame with lower press table made of stainless steel as a grounding electrode Quick-change stop guide sets for panel thicknesses of 19 - 40 mm, which can be hydraulically adjusted to the current filling width Hydraulic special pressure elements ensure uniform pressure distribution over the entire joint length and compensate for tolerances In multi-lane operation, filling widths may vary by a maximum of 15 mm Upper pressure plate with hydraulic drive generates high vertical pressing pressure for minimal displacement Integrated hydraulic unit for generating pressing force and driving the hydraulic motors Control cabinet and control panel Protective cladding Additional individual pressure elements from above Automatic gluing station with precision gluing head Infeed for different widths Camera Washing and rinsing device for gluing head Modem incl. software for online connection Note: The technical data and descriptions are copies of the order confirmation from that time. The information is provided for informational purposes only and is non-binding. Itodozuzwqjpfx Ah Uel

Condition: used, Year of construction: 2019, Corpus press Manufacturer: LINYI JIANZHONG WOOD MACHINERY Type: JJZ-CP Year of manufacture: 2019 The JJZ-CP press is suitable for the production of plywood, doors, and MDF panel joints. The feeding and removal of the glued elements are carried out automatically via powered roller conveyors. Technical data - Max. pressure 500 t (adjustable) - Max. filling height 1300 mm - Min. filling height 900 mm - Max. filling size 1300 x 2500 mm - Press dimensions 3600 x 1370 x 4500 mm - Press placement approx. 500 mm below floor level - Feeding table 2000 x 1960 mm - Receiving table 2350 x 2500 mm Itsdpfozuzwksx Ah Uol - Max. power 13.2 kW - Weight 12000 kg - CE marking - Capacity: 6 batches per hour 2 corpus presses are available for sale. Note: The technical data and descriptions are transcriptions from the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2000, Corrugated board press Manufacturer: Hüttenhölscher Year of manufacture: 2000 Technical data Voltage: 400 V Current: 32 A Frequency: 50 Hz Compressed air: 6 bar Note: Itodpfx Ajzuzvmsh Usl The technical data and descriptions are a transcript of the order confirmation from that time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2001, Thermo-lamination system Manufacturer: BÜRKLE Type: FFAII 1300 Year of manufacture: 2001 Itodpfozuzt Sjx Ah Uel Technical data: Working width: 1300 mm Panel dimensions Width: 200 - 1300 mm Length: 400 - 3000 mm Thickness: 8 - 40 +/- 0.2 mm Film dimensions Width max. 1320 mm (lateral overhang up to 20 mm) Roll diameter 76 or 152 mm (3" or 6") Working height above floor: 940 mm System speed: 15 - 45 m/min Three-phase drive with vector control Operating side: right Panel feed: centered System configuration FFAII 1300 - Brush machine DBM (chain brushes) - Preheating and smoothing calender GKL, D = 500 mm - Thermo-oiler heater 36 kW - Hardener application machine DAH + complete hardener circulation system with monitoring - Transport section + IR zones with temperature sensors - Adhesive application machine DAK + automatic level sensing - Cooling unit for DOW cooling - Adhesive supply - Conical transport section TKE - Lamination calender EKM, D = 500 mm + film unwinding station + separating station + belt transport section with operator platform for FVE - Expansion shafts - Smoothing calender GKL, D = 500 mm at the inlet of the conveyor belt - Thermo-oiler heater 96 kW for lamination calender and smoothing calender - Central control cabinet - I.S.E. Optimat ISL 111 (year of manufacture 2004) Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2016, Laminate Coating System Manufacturer: Type: Master PUR-1400 Year of manufacture: 2016 Technical data Professional PUR hot-melt laminating system for acrylic, PET, PVC, HPL, and CPL sheets General description The MASTER PUR-1400 is a professional, high-performance laminating system designed for single-sided lamination of sheets with PUR hot-melt adhesive. The system is suitable for continuous industrial production and offers excellent surface quality with low adhesive consumption. It is designed for the production of high-quality furniture panels, interior design components, wall panels, and decorative panels. Suitable substrates The machine is suitable for laminating: MDF Chipboard Plywood PVC sheets Gypsum boards Other wood-based panels Compatible surface materials The system is designed for processing the following materials: Acrylic sheets (high gloss & super matte) PET film PVC film HPL laminate CPL laminate Decorative paper Technical data Working width: 1,400 mm Maximum sheet size: 2,800 x 1,300 mm Sheet thickness: 2-40 mm Production speed: 5-17 m/min Throughput: 3-5 sheets/min Maximum productivity: up to approx. 1,200 sheets per 8-hour shift Installed motor power: 21.49 kW Heating power: 51.7 kW Overall dimensions of the machine: approx. 16 x 2.5 x 2 m Required installation area: at least 6 x 22 m System configuration The production line includes: Automatic feeding system with roller conveyor Brush cleaning system for sheets Infrared preheating oven (IR) 3-roller PUR adhesive application system Feeding station for decorative material Laminating press with pressure rollers Take-away conveyor Itsdpfxozuzkqo Ah Uol 208-liter melting tank for PUR hot-melt adhesive Advantages Excellent laminating quality Uniform PUR adhesive application Suitable for high-gloss and super-matte acrylic surfaces Low adhesive consumption Stable and reliable operation in industrial series production High production efficiency Easy operation and maintenance Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2001, Short-cycle pressing line Manufacturer: Wemhöner Type: KT-F-1E Year of manufacture: 2001 Technical data - Pressing area: 5,750 mm x 2,200 mm - Operating side: left - Plate dimensions: Length: 2 x 2,600 mm - 2 x 2,620 mm Width: 2,070 mm Thickness: 6 mm - 40 mm - Pressing pressure: approx. 40 kg/cm² Note: Upon request, the complete layout plan of the system can be sent. Iodezuzi Tjpfx Ah Ujtl Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 1994, operating hours: 392 h, functionality: limited functionality, machine/vehicle number: 1115, type of input current: three-phase, total height: 150 mm, total length: 2,200 mm, total width: 900 mm, overall weight: 1,800 kg, power: 11 kW (14.96 HP), input voltage: 380 V, Equipment: documentation/manual, Brand: Pawert Isdpfxozyau Eo Ah Uotl Type: I-40/85 Year of construction: 1994 Capacity: 150 kg/hour Briquette dimensions: Ø 40 mm Motor: 11 kW Weight: 1800 Including feed screw and discharge chute.

Condition: new, functionality: fully functional, Equipment: documentation/manual, | price list | prices | prices | prices | prices | prices | prices | prices | > > > > > ecomas.pl/price-list < < < < < You can view the prices at the very bottom of the listing: Documents / 20215835-01.pdf Itsdjxk Ta Nopfx Ah Ujl We offer a high-quality, low-speed pellet granulator. The pellet mill is 100% manufactured in our plant at ECOMAS Polska Czernikowo. We guarantee equipment designed to operate continuously in a 24/7 system. Our machines produce pellets that meet EU standards – properly compacted, free of harmful additives, with a calorific value of at least 4.6 kWh/kg. The main advantage lies in modern, hardened dies and rollers (60HRC+), manufactured with CNC technology. Our dies ensure high efficiency, low power consumption, and long service life of both dies and rollers. Another benefit is the lubrication of the main shaft with oil and oversized bearings, which significantly slows down wear! Are you struggling with your current granulator – bearing failures, low efficiency, clogged die, high power consumption, rapid wear of parts, etc.? With our machines, these problems disappear. We approach each customer individually! See how our machines produce, type in YouTube: ecomas_polskie_peleciarki Available power options: 7.5kW, 11kW, 15kW, 18.5kW, 22kW, 30kW, 37kW, 45kW up to 55kW. Composition: - complete head with 2/3/4/5 rollers on cylindrical bearings - welded body – fully filled with Orlen Oil Transol VG 320 - cylindrical-bevel gearbox (efficiency 98%) - base frame - bolted dies fi 230, fi 260, fi 285, fi 310, fi 400, fi 520; hole diameters 3, 4, 5, 6, 8, 10mm (100% stability, easy disassembly, and temperature control) - standard oil tank or optional tank with pump and oil installation (oil lubrication, easy oil replacement) - user manual - 12-month warranty The buyer receives a detailed operating manual and a one-year warranty. We provide full warranty and post-warranty service.

Year of construction: 1999, condition: used, Colour: Grey Membrane press Orma PM/AIR Year of construction 1999 Serial number 52850199 Dimensions 2300*900mm Max panel size 2200x800mm Max panel thickness 40mm 8 cylinders diameter 100mm Stroke 150mm Pressure 160T Pressure pressure 6 kg/cm² Heating 13kW Total power 17.3kW 380V, 35Amp Dimensions: 3900x1800xH2100mm, weight 5900kg - Year: 1999 - Documentation available: No Itodpfx Aswnhiceh Ujl - CE certificate present: No - Serial number: 52850199 - Main motor power [kW]: 17.3 - Max. workpiece length [mm]: 2200 - Max. workpiece width [mm]: 800 - Max. workpiece height [mm]: 40 - Number of cylinders [pcs.]: 8 - Cylinder diameter [mm]: 100 - Total working pressure [Ton]: 160 - Working pressure [kg/cm²]: 6 - Heating boiler present: Yes Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, total length: 11,500 mm, total width: 2,450 mm, total height: 2,600 mm, Colour: Green Empty weight: 16.500 kg Veneer press Feed-through press HOT Colombo Machine dimensions: 4400x1400 Oil heated input/output is included 8 cylinders Complete with glue roller etc. - Documentation available: No - CE certificate present: No - Press drive: Hydraulic - Max. workpiece length [mm]: 4500 - Max. workpiece width [mm]: 1400 - Max. workpiece height [mm]: 140 - Total stroke [mm]: 140 - Number of stages [pcs]: 1 Itodpfxownhvve Ah Ujl - Material of press plates: Steel - Number of cylinders [pcs]: 8 - Cylinder diameter [mm]: 85 - Working pressure [kg/cm²]: 4 - Heating type: Oil heated - Voltage [V]: 400 - Transport dimensions: 11500mm x 2450mm x 2600mm (l x w x h) - Transport weight [kg]: 16500kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: excellent (used), Year of construction: 1995, functionality: fully functional, Hydraulic Frame Press HESS LUX 2000 The machine is fully operational and in good condition Itodpfx Aexl Dv Deh Usl Maximum working dimensions: 4300 x 2600 mm 3 top and 3 side cylinders Electric dimension adjustment from the control panel.

Condition: reconditioned (used), functionality: fully functional, Veneering press line for wood, consisting of the following machines: - OSAMA S2R adhesive applicator - 1300 mm - NEW MACHINE - Feeder from the adhesive applicator to the conveyor - Infeed conveyor, 6000 mm long x 950 mm wide, with drive - ORMA 5100x1400 mm surface hydraulic press - 12 pistons, hot water plates, refurbished - Outfeed conveyor, 6000 mm long x 950 mm wide, with drive This press requires medium to high pressure for operation to ensure that the boards are 100% flat. Iodpfxsvva Sye Ah Uetl Dimensions of veneering boards: 5100 x 1400 mm (solid, drilled steel boards) Board opening: 180 mm Pressure at full surface: up to 10 kg/cm2 Number of hydraulic pistons: 12 pcs - piston diameter 140 mm Teflon MYLAR film on the boards Preparation for heating the boards with hot water - without a boiler Machine dimensions: 2300 x 5100 mm x height 2500 mm The machine has been completely refurbished, adjusted, and tested. Price: EUR 49,000,- excluding VAT, without the OSAMA adhesive applicator Price: EUR 58,000,- excluding VAT, including the OSAMA adhesive applicator

Condition: excellent (used), Year of construction: 2007, Catalog number: 7809 TECHNICAL DATA - Pressing force: hydraulic - Briquette shape: round - Briquette diameter: 70mm - Hopper diameter: 900mm - Automatic machine operation Iodpfx Ahszu Sxxo Uetl - Inspection window in the machine hopper - Equipped with an additional oil heater - Motor: 5.5kW - Dimensions (L/W/H): 1600x1200x1500mm - Weight: 685kg ADVANTAGES - Unpainted - Made in Italy - Equipped with an additional oil heater - Used briquetting machine - Very good condition Net price: 36,900 PLN Net price: 8,786 EUR, depending on the exchange rate of 4.20 EUR (Prices may vary due to exchange rate fluctuations)

Year of construction: 2021, condition: excellent (used), Insert nut (insert sleeve) machine, Stafast HFM-CF. The machine is configured for M8 nuts with a large flange. The machine is in very good condition. Iedsy Ui Tiepfx Ah Uotl Ready for use.

Condition: used, Year of construction: 2008, functionality: fully functional, For sale: a window and door pressing machine, model Junior, manufactured by the Italian company Casolin. Bale pressing machine. Itjdpfjzzn Dwex Ah Ujl Working area: 3000 mm (width) x 2500 mm (height). The machine is in good working order. We have the instruction manual in English. Export price – domestic price + VAT. Transportation is the responsibility of the buyer; loading is the responsibility of the seller.

Condition: like new (used), Year of construction: 2023, operating hours: 200 h, functionality: fully functional, Complete pellet production line, consisting of: Wood chip feed hopper 8m³ Hammer mill 22 kW Chip bunker with 3 discharge openings Screw conveyor with dosing unit (binder) Walw pellet press Conveyor belt Pellet cooling bunker with packaging unit and fine particle screening Iedpfxjy Ayiwe Ah Ustl

Condition: like new (used), Year of construction: 2009, functionality: fully functional, operating hours: 4,000 h, input voltage: 380 V, input current: 80 A, input frequency: 50 Hz, type of input current: DC, pressing force: 160 t, stroke length: 150 mm, operating speed: 50 mm/s, reverse speed: 10 mm/s, table width: 1,300 mm, table length: 2,500 mm, table height: 150 mm, throat depth: 1,300 mm, ram plate width: 1,300 mm, ram plate length: 2,500 mm, distance table to ram: 200 mm, clearance between the columns: 2,500 mm, retraction force: 100 t, oil tank capacity: 50 l, total length: 3,500 mm, total width: 4,500 mm, total height: 2,300 mm, overall weight: 6,000 kg, year of last overhaul: 2024, Equipment: CE marking, documentation/manual, We offer this Dimter Profitest 2500 gluing press in like-new condition, manufactured in 2009. Manufacturer: Dimter Model: Profitest 2500 Itedpozin Aiefx Ah Ujl Year of manufacture: 2009 Condition: like new Type: gluing press If you have any questions or require additional information, please send us a message or contact us by phone.

Year of construction: 2014, condition: used, functionality: fully functional, Equipment: CE marking, We offer this used Vechiatto PRESSA 1900*820 10V R4000 press for the production of spring strips, manufactured in 2014. Manufacturer: Vechiatto Model: PRESSA 1900*820 10V R4000 Year of manufacture: 2014 Ijdpjztdbvefx Ah Uetl Condition: used Machine type: Press for the production of spring strips If you have any questions or require additional information, please send us a message or contact us by phone.

Condition: used, Year of construction: 2022, total width: 1,800 mm, total height: 1,900 mm, total length: 1,800 mm, overall weight: 3,000 kg, Hydraulic briquette press Itjdpfjzxlznjx Ah Ujl Manufacturer: Winter Type: BP 450 Year of manufacture according to nameplate: 2022 Technical data: Capacity max. 450 kg/h Motor 35 kW / 400 V, 50 Hz Chip compression min. 1,000 kg/cm² max. 1,500 kg/cm³ Wood moisture < 14 % Briquette dimensions: Length 150 mm, Width 60 mm Dimensions L x W x H: 1,800 x 1,800 x 1,900 mm Weight 3,000 kg Purchase price net € plus applicable VAT. VAT will be shown separately on our invoice. Subject to changes, errors and prior sale. Sale is made without warranty and guarantee, and only to business customers. Inquiries will be processed from Monday to Friday between 8 a.m. and 4 p.m.

Condition: new, Year of construction: 2025, Dimensions: length 1800 mm, width 1800 mm, height 1900 mm . Weight netto 3000 kg. Eletric power of the press: 380 V 50 Hz 33 kW 70-100 A Capacity of the press: 450-500 kg/h Pressure: minimum 1000 kg/cm², maximum 1700 kg/cm2 Dimensions of the briquette: length 150 mm Ijdsc Nb Rfepfx Ah Uetl width 60 mm height 40 – 105 mm

Condition: refurbished (used), functionality: fully functional, briquette diameter: 70 mm, DIN 140 N briquetting machine, capacity 140 kg/h, briquette diameter 70 mm Year of manufacture: 2022 Completely overhauled In perfect working order Itedpfx Ahozy R Nms Ujl Used for demonstration purposes

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: HaRo2020, total width: 800 mm, total height: 1,100 mm, total length: 1,200 mm, briquette diameter: 60 mm, overall weight: 300 kg, warranty duration: 12 months, type of input current: AC, input voltage: 400 V, power: 3 kW (4.08 HP), Equipment: emergency stop, Our new HaRo2020 briquetting press, with a capacity of up to 40 kg/h, automatic tongs, and pre-compactor, is manufactured by ourselves. You can only purchase this machine directly from us, as we do not use intermediaries. The briquetting presses are CE-compliant and manufactured according to the latest standards. Since we produce most of the components in-house, we can offer the machine at a particularly competitive price. Price is exclusive of VAT. The new hydraulic unit is equipped with a SILENCE-PUMP, making the machine extremely quiet in operation. Another benefit of the helical gearing in the pump is increased durability. Iedpfx Asw A Hvdjh Ustl Everything is made in Germany! You are welcome to visit us and test the machine with your own material. When purchasing our briquetting press, you will receive a detailed and comprehensive German (PDF) operating manual for this machine. The input material must have a moisture content below 15%—ideally 10 to 12%—for sawdust and planer shavings. Technical Data – Hydraulic unit: 3.0 kW (connected load) – Power consumption per hour: approx. 1.8–2.0 kWh – Throughput: approx. 15–40 kg/h – Voltage: 400 V – Frequency: 50 Hz – Circuit protection: 16 A plug – Power cable length: 3 m – Hydraulic control with Bosch Rexroth valves – Briquette diameter: 60 mm (length varies according to material) – Motor equipped with motor protection switch and emergency stop—for operator and machine safety, including motor protection – No electronic components prone to failure such as controllers, sensors, or complicated electronics – Pressing without additives – Counter-pressure adapts fully automatically to your material – Thanks to the pre-compactor, bulky shavings are no problem – No adjustments or monitoring of the pressure required – Fully automatic operation Spare parts supply is guaranteed, as we manufacture the machines in small series in our facility in Germany. The large oil tank ensures that the oil will not overheat during continuous operation. Machine dimensions: Length: 1.25 m Width: 0.82 m Height: 1.11 m Feed hopper: Diameter approx. 80 cm x height 60 cm Weight: 300 kg The briquetting press is immediately operational and does not require installation—just plug it in and start working. The machine can be viewed and tested on-site. You are welcome to send us a sample of your material for testing; we find this is the most effective method.