Condition: not inspected (used), Year of construction: 2005, functionality: unexamined, workpiece height (max.): 40 mm, edge thickness (max.): 3 mm, feed rate X-axis: 35 m/min, rotational speed (max.): 12,000 rpm, number of slots in tool magazine: 48, TECHNICAL DETAILS Panel height min.: 10 mm Fpodpfeyqybuex Ah Ajd Panel height max.: 40 mm Edge thickness min.: 0.4 mm Edge thickness max.: 3 mm Feed speed max.: 35 m/min PROCESSING UNITS Pre-milling unit Automatic engagement 48 tool positions End trimming unit 2 motors Fine trimming unit 1 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Fine trimming unit 2 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Edge scraping unit Glue scraping unit Polishing unit 2 motors Spraying device MACHINE DETAILS Control system: PC 22 EQUIPMENT Pressure applied with rubber belt Panel guides with NC positioning Glue pot for EVA hot-melt adhesive Pre-melter for EVA hot-melt adhesive Laser system (Model: LaserTec) Roller set for edge pressing with 5 pressure rollers Units mounted on safety guards CE marking The machine is sold and delivered in its actual and legal condition (“as seen and approved”), based on photo documentation and technical/commercial descriptive documentation. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 5321

Condition: not inspected (used), Year of construction: 2007, functionality: unexamined, working width: 1,935 mm, number of spindles: 40, plate height: 350 mm, working length: 6,200 mm, number of axes: 4, TECHNICAL DETAILS Working area X-axis: 6,200 mm Working area Y-axis: 1,935 mm Maximum panel thickness: 350 mm Fjdpfx Aeyqx U Hoh Aspd Number of edge tape magazines: 3 Number of tool positions in tool magazine: 22 (located at the rear of the machine) Drilling spindles Spindles for vertical drilling: 28 Spindles for horizontal drilling in X direction: 4 Spindles for horizontal drilling in Y direction: 8 Total number of vertical + horizontal spindles: 40 Milling spindles Number of controlled axes: 4 Motor power: 10.5 kW Automatic tool changer MACHINE DETAILS Total connected load: 31 kW EQUIPMENT Suction cups for securing the workpiece Safety mats at the front Vacuum pump Waste chip conveyor Fixed groove unit for slotting in X direction The machine is sold and delivered in its actual and legal condition (“as seen and approved”) on the basis of photographic documentation and descriptive technical/commercial documents. The buyer has the right to inspect the item prior to collection and assumes responsibility for installation, securing, and operation of the machine at the place of destination. External reference: 8105

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, workpiece height (max.): 90 mm, workpiece width (max.): 3,200 mm, workpiece length (max.): 3,200 mm, edge thickness (max.): 3 mm, The machine has the following configuration: Number of panel sizing/milling units on the left side: 5 Milling unit (AS10) Double finishing cutter, top and bottom 2 pre-milling units Milling unit Number of edge processing units: 10 End trimming Top and bottom trimming (rough) Fine trimming for chamfering and rounding Corner rounding (AR34, 4 motors) Edge milling (FB40, 1 motor) Edge scraping Belt sanding (1 motor) Glue scraping Polishing (2 motors) Spray device TECHNICAL DETAILS Fpodeyq Avhjpfx Ah Aod Minimum panel height: 10 mm Maximum panel height: 90 mm Maximum panel length: 3,200 mm Maximum panel width: 3,200 mm Minimum edge thickness: 0.4 mm Maximum edge thickness: 3 mm FEATURES Feed chain with carriers Pressure applied via rubber belt Panel guide rails with NC positioning Edge roll magazine with 6 positions Hot melt adhesive system for PUR adhesive NORDSON Roller set for edge pressing 4 pressure rollers with NC positioning Spray device mounted on upper cabinets The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photo documentation and descriptive technical/commercial documents. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and operation of the machine at the destination. External reference: 7685

Condition: used, machine/vehicle number: 006710, Type of edging: Thin edge, Thick edge, Solid wood, Veneer Gluing System: EVA Hotmelt, Hot Air Premilling Unit: yes Corner Rounding Unit: yes Max feed speed: 11 m/min Fpjdpfeqy Em Tox Ah Aed

Condition: used, machine/vehicle number: 008132, Type of edging: Thin edge, Thick edge Gluing System: EVA Hotmelt Fjdpfx Ahew Idc Rj Ajpd Premilling Unit: yes Corner Rounding Unit: yes Max feed speed: 18 m/min Maximum panel thickness: 60 mm Operating Units: 7 nr

Condition: used, machine/vehicle number: 008109, Type of edging: Thin edge, Thick edge, Solid wood Gluing System: EVA Hotmelt Premilling Unit: yes Corner Rounding Unit: yes Fpsdpsw Idc Defx Ah Aod Maximum panel thickness: 12 mm Operating Units: 9 nr

Condition: excellent (used), Year of construction: 2020, Homag Edgeteq S-200 Year: 2020 Specification: Feed Speed 11m/min Machine Length 4605mm Workpiece Thickness max 60mm Edge Material Roll 0-3-3mm Edge Material Strips 0.4-5mm Fedpfx Ahjypm Hhj Aspd Joint trimming / pre-milling (44mm high blocks) Standard EVA glue unit Pressure zone with 1 main pressure roller + 2 idel rollers with pneumatic adjustment for thickness End Trim unit with pneumatic adjustment for chamfer / straight Top and bottom trimming unit with 2mm cutters Contour trimming unit with 2mm cutters Profile scraping with pneumatic adjustment with 2mm blades Additional changeable scraping heads with 1mm blades Glue Joint scraper Buffers LED indoor lighting Control system easy touch Package for construction elements Basic v Package Central Lubrication 400V 50Hz CE

Condition: excellent (used), Year of construction: 2019, Specification Fpedpjypm Dgjfx Ah Aed 2 tanks 1 cleaning station Suitable for right sided machine such as Edgeteq S-240, S-300 and S-380 400V 50Hz

Condition: excellent (used), Year of construction: 2019, Specification: Working height: 950mm Length: 4773mm Workpiece Thickness: 60mm Edge Material Roll: 0.4-3mm Edge Material Strip:0.4-6mm Adjustable Infeed Fence Workpiece Support Feed Speed 11m/min Central Lubrication Roller Top Pressure Manual Top Pressure Adjustment Fpodeypm Avspfx Ah Ajd Separating Agent Spray Device Joint Trimming Unit 2x2.2kw Panel Pre-Heating QA65 Application unit for PUR Pressure Zone End Trim Unit Trimming Unit Counter Trimming unit Radius Scraping Unit with 2 sets of quick change heads Glue Joint Scraping Detergent Spraying Unit Buffers 400V 50Hz CE XES 200 with 2 tanks and 1 cleaning station including collecting tray.

Condition: used, Year of construction: 2012, total height: 1,600 mm, total length: 5,250 mm, total width: 1,440 mm, Weight: 1.550 kg Edgebander HEBROCK AKV 3006 DK FS maximum edge thickness 3/8 mm min/max. workpiece thickness 10/40 mm min. workpiece length approximately 200 mm min. workpiece width approx. 80 mm feed speed about 10 m/Min. ready in about 6 minutes. maximum power consumption 12 kW electrical connection 400 V / 3 Ph / 50 Hz Pre-mill Glue unit Pressure roller Chopping saw Milling unit Milling unit Corner rounder Fpjdpfx Ajwnhb Soh Asd Radius scraper Flat scraper Cleaning unit Dimensions (length x width x height) 5250x1445x1600 mm, weight 1550kg - Year: 2012 - Documentation available: No - CE certificate present: No - Transport dimensions: 5250mm x 1445mm x 1600mm (l x w x h) - Transport weight [kg]: 1550kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: excellent (used), Akzent edge banding machine V31 - Dimensions: 1750 x 530 x 600 mm - Plus additional 600 mm Ø roller table Fpjdpfx Aoytw Ttoh Aed - Milling motor with disc cutter - Workpiece thickness: 10-55 mm - Edge thickness: 0.4-1 mm - 220 Volt - 3.3 kW - Weight: 135 kg

Condition: used, Year of construction: 2013, Used machine Year of manufacture: 2013 Equipment/features: - Machine table with 13 running rollers for improved workpiece guidance - Edge feed, synchronized with the belt feed - Edge thickness adjustable via digital counter - Pneumatic roller separation with cutter (for cuttable edges) - Three pressure rollers - Belt feed motor 0.25 kW; approx. 1250 mm length; feed rate approx. 6.0 m/min; 50 mm wide timing belt with thick, workpiece-friendly rubber coating. Digital counter for height adjustment Fpedpfx Aeytkiujh Aed - Direct glue application to the workpiece: leakproof glue pot with glue supply from below and fast heat-up time after machine stoppage - Flush trimming unit for front and rear workpiece edges, automatic sensing at the workpiece, pneumatic trimming with a cutter for cuttable edges - Flush milling unit with vertical sensing and horizontal guidance, reproducible adjustment via digital counters, 2 high-performance 0.4 kW high-frequency motors, continuously adjustable from 4000 to 18000 rpm, cutter diameter 70 mm, Z4, radius 2 mm/15°; central extraction connection Ø 100 mm, 2 chip extraction hoods with hose Ø 60 mm - Automatic height adjustment of the upper cutter with the belt feed - Continuous workpiece support approx. 1800 mm long, workpiece support rail extendable by approx. 300 mm - Rotatable film disc Ø 800 mm Technical details: - Minimum workpiece width: approx. 80 mm - Workpiece thickness: 10 – 50 mm - Minimum workpiece length: approx. 220 mm - Edge thickness: 0.4 – 2.0 mm - Roller separation max.: 1.0 x 55 mm, 2 x 45 mm - Glue pot heating power: 2.7 kW - Electrical connection: 400V, 50 Hz, 3Ph + N - Total connected load: 3.8 kW - Heat-up time: approx. 10 minutes - Pneumatic connection: 6 bar - Working height: approx. 880 mm - Dimensions: approx. 1800 x 700 x 1300 mm (without film disc Ø 800) - Net weight: approx. 260 kg Availability: short-term Location: Flörsheim

Condition: ready for operation (used), Year of construction: 2006, Edgebander manufactured in 2006. This HOMAG Optimat KAL 330 features a flexible production layout for furniture parts, accommodating workpiece dimensions from 250 to 3000 mm in length and 120 to 1200 mm in width. It includes a single-sided edge banding machine capable of processing various edge materials up to 20 mm thickness. If you are looking to get high-quality edge processing capabilities, consider the HOMAG Optimat KAL 330 edgebander we have for sale. Contact us for further details. • Line workpiece capacity: • Length 250–3000 mm • Width 120–1200 mm • Thickness 8–60 mm • Edge bander (KAL 330) — base and transport • Continuous machine base; workpiece support with roller bar extendable ~800 mm • Transport chain 80 mm wide with rubber surface; precision guidance, hardened surfaces • Top pressure: driven belt • Technical data: • Feed speed 18–25 m/min • Working height 950 mm • Minimum working width: 55 mm at 22 mm thickness; 100 mm at 60 mm thickness (depending on workpiece length) • Workpiece overhang/supernatant 30 mm • Workpiece thickness 12–60 mm • Edge material from strip: 0.4–20 mm (max cross-section 900 mm²) • Edge material from coil: 0.3–3 mm (max cross-section: PVC 135 mm², veneer 100 mm²) • Max coil diameter 830 mm • Pneumatic connection 7–8 bar • Infeed system and controls (integrated with KAL 330) • Flexible workpiece infeed system wz10 for automatic infeed (lengthwise and crosswise); for precisely sized, square parts • Stepless infeed guidance adjustment (axis), speed set at input terminal • Automatic side adjustment of units (workpiece overhang 30–80 mm) for gluing and post-processing • Input terminal; solvent applicator top/bottom • Edge preparation and gluing • Pre-milling unit: 2 motors, each 4 kW, 150 Hz, 9000 rpm; electro-pneumatic control • Stepless vertical axis SF20 for automatic centering to panel thickness • Pre-melting unit with granule storage • Quick-lock system for QA/QE application unit; QA front glue storage for color change • Basic gluing unit A20; magazine height adjustment ±5 mm (manual spindle) • Extended magazine A6/A-E12/A20 for 2 coils (max Ø 830 mm); preheating station for QA/QE • Automatic pressure zone adjustment • Trimming and milling • Trimming unit HL84 with standing trimming stop for sensitive edges • Pneumatic trimming motor adjustment (2 positions: flush/level and with overhang for contour milling) • Pneumatic chamfer/straight changeover; manual side trimming stop adjustment when edge thickness changes • Rough milling unit: 2 motors stacked, each 1.5 kW, 200 Hz, 12,000 rpm; height adjustment via top pressure • Pneumatic 2-position setting: roughing with ~0.2 mm overhang / without overhang • Reserved free space for a fine milling unit • Contour milling unit Servo FK13 automatic: • 2 motors each 0.4 kW, 200 Hz, 12,000 rpm • Servo-controlled movements; automatic 8-fold tool changer • Feed speed max 20 m/min; minimum spacing between workpieces 500 mm • Workpiece thickness 12–60 mm • Automatic FK adjustment for identical radii on different edge thicknesses; auto retract • FK workpiece guidance with additional clamping for min part length 120 mm (single-sided) • Finishing and cleaning • Multi cleaning unit MN21 automatic: Fpjdpjytf Irjfx Ah Asd • Up to 3 profiles; tracing from top/bottom/side for chamfer and rounding on pre-milled PVC edges • Electropneumatic air nozzles; automatic chamfer/radius changeover; auto retract of upper/lower tool • Height adjustment via top pressure • PVC shavings separator top/bottom

Condition: used, Year of construction: 2018, Edge banding machine AKV 3006 DK - F with jointing unit, including DIA tools • Jointing capacity up to 40 mm • Workpiece thickness up to 3 mm • Combination milling station, radius R 2.5 mm Technical Description: - Hot melt adhesive application to the workpiece for edge materials up to 3 mm Fpedpfx Aox S Hmzjh Asd - Workpiece thickness up to 60 mm without jointing unit, up to 40 mm with jointing unit - Maintenance-free, coated gluepot - HF end-trimming unit (16,000 rpm) for front and rear edge overhang - HF milling station (16,000 rpm) with replaceable cutter heads (combination version) and fine adjustment from the operator side - Free spaces for additional processing units (Hebrock system) - Feed speed approx. 10 m/min - Cutting depth adjustment of the end-trimming saw - Signal lamp for workpiece flow - Robust chain feed - Ergonomically arranged control panel - Double roller upper pressure beam - Aggregate windows on machine rear and operator side - PLC control with touchscreen included Technical Data: - Feed rate: 10 m/min - Panel thickness: 8 – 40 mm - Weight: approx. 1550 kg (depending on configuration) - Dimensions (L x W x H): 5250 x 1445 x 1600 mm Airtronic incl. cooling and antistatic spray system (2014) • 1 pc hot air unit for visual zero joint using special edge materials • Including pneumatic gluepot positioning • Including cooling and antistatic spray system • Including 2 additional quick-change edge channels • Including special version corner rounding unit; max. workpiece thickness 60 mm, min. length 200 mm - Exclusively for Hebrock 3000 series edgebanders - Retrofitting possible at extra cost upon request Technical Data (special unit): - Max. panel thickness: 40 mm - Edge thickness: 1.2 – 2.0 mm - Feed speed: 7 – 10 m/min - Air consumption: approx. 280 – 580 l/min (only Airtronic), electronically controlled - Ready for operation after approx. 2 min Upgrade to 8 mm edge thickness possible; max. workpiece thickness 40 mm • Including pneumatic saw adjustment (special version, min. workpiece thickness 8 mm) • 3-point pneumatic milling shift • Selector for radius/chamfer/flush for combination milling stations, eliminating manual changeover (PLC control required) Buffing station (swab): 1 pc Corner rounding unit: 1 pc incl. combination tooling and pneumatic radius/chamfer adjustment, max. 40 mm workpiece thickness, min. 300 mm workpiece length, Radius R 2.0 mm Radius scraper: 1 pc with pneumatic lift, Radius R 2.0 mm Flat scraper: 1 pc with pneumatic actuation Complete chassis: 1 pc Glue station quick-change system incl. glue discharge system (downward outlet in preparation), 1 pc (no second gluepot), machine can process PU adhesive Grooving unit (vertical for panel): 1 pc incl. pneumatic lift, vertical groove, groove width 8.2 mm, groove depth 8.0 mm, distance from panel edge 14.0 mm; special motor version with higher performance Extraction for internal jointing unit: 1 pc connected to machine's extraction manifold Corner rounding cutter ball bearings: 24.1 mm (1 pc), 24.2 mm (1 pc) Edge protection spray system: 1 pc for sensitive edge materials Combined spray system (separating and cleaning agent): 1 pc Location: Supplier stock

Condition: ready for operation (used), Year of construction: 2013, This 5-axis SCM Stefani MD HP edgebander was manufactured in 2013. It features a robust steel construction, high-frequency motors, and a "Startouch" control system with a 12" touchscreen. Capable of handling solid wood edges up to 15 mm and rolls up to 3 mm, it includes a pre-milling unit, interchangeable glue pot, and a feed speed of 25 m/min. Consider the opportunity to buy this SCM Stefani MD HP edgebander. Contact us for more information. Fpjdpjx I S R Dsfx Ah Aed Application Types Edge Banding

Condition: ready for operation (used), Year of construction: 2009, This STEFANI Solutions 86 edgebander was manufactured in 2009. It features Nordson equipment, a maximum glued edge thickness of 25 mm, and a maximum panel thickness of 60 mm. The machine includes electric height adjustment, upper belt pressure, and a preheating zone. It also boasts interchangeable roller storage with 12 positions and a replaceable glue pot. Consider the opportunity to buy this STEFANI Solutions 86 edgebander. Contact us for more information about this machine. Fedpox Nr Raefx Ah Aepd Application Types Edge Banding

Condition: ready for operation (used), Year of construction: 2010, Additional Equipment Fodpfsx R E Nfjx Ah Aspd Feed Speed: 7 m/min / Min. Panel Length: 80 mm / Min. Panel Width: 60 mm/ Max. Panel Height: 40 mm / Edge Thickness: Up to 3 mm / Glue Pot Capacity: 2 liters End Trimming: Dual vertical saws at 12000 rpm / Profile Trimming: Inclined unit at 15° with 12000 rpm This 6-axis Bi Matic CH 2.2 edgebander was manufactured in 2010, featuring a glue pot capacity of 2 liters and dual vertical saws for end trimming at 12,000 rpm. It supports edge thickness up to 3 mm and requires an air pressure of 6 bar. If you are looking to get high-quality edgebanding capabilities, consider the Bi Matic CH 2.2 machine we have for tact us for more information. Application Types Edge Banding

Condition: used, Year of construction: 2013, total height: 2,100 mm, total length: 9,000 mm, total width: 1,050 mm, Weight: 6.000 kg Price: On request - Details: - └ Description: Not working: Several loose sensors and the glue bin has been disassembled, machine has not yet been tested - Year: 2013 - Documentation available: No - CE certificate present: No - Serial number: - Number of units [pcs]: 9 Fsdpsyrp Uaefx Ah Aopd - └ 1st unit type: Pre-milling unit - - Tools available: Yes - └ 2nd unit type: Glue unit - - Type/Brand: Nordson - └ 3rd unit type: Pressure rollers - - Tools available: Yes - └ 4th unit type: Cap unit - - Tools available: No - └ 5th unit type: Rough milling unit - └ 6th unit type: Milling unit - └ 7th unit type: Fine milling unit - └ 8th unit type: Milling unit - └ 9th unit type: Milling unit - - Tools available: Yes - Glue system: Glue pot - Voltage [V]: 400 - Current consumption [A]: 69 - Fuse [A]: 80 - Transport dimensions: 9000mm x 1050mm x 2100mm (l x w x h) - Transport weight [kg]: 6000kg - Transport packages [pcs.]: 4 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2017, total height: 2,100 mm, total length: 6,700 mm, total width: 1,050 mm, Weight: 3.500 kg Price: On request - Details: - └ Description: Includes Nordson unit built in 2017 - Year: 2017 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: - Number of units [pcs]: 6 - └ 1st unit type: Pre-milling unit - - Type/Brand: Nordson - - Tools available: Yes - └ 2nd unit type: Glue unit - └ 3rd unit type: Pressure rollers Fsdoyrpvwjpfx Ah Aepd - - Tools available: Yes - └ 4th unit type: Rough milling unit - └ 5th unit type: Cap unit - └ 6th unit type: Fine milling unit - Voltage [V]: 400 - Current consumption [A]: 41 - Fuse [A]: 50 - Transport dimensions: 6700mm x 1050mm x 2100mm (l x w x h) - Transport weight [kg]: 3500kg - Transport packages [pcs.]: 5 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: excellent (used), SINGLE SIDE EDGE BANDER (Left) Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 Edges thickness in strips / lippings (min/max) mm 0,4 / 20 Panels thickness (min/max) mm 8 / 60 NEW (in 2024) Numerical Control EDGETEQ MOD - Power Touch (WoodCommander) Adjustable Feeding speed up to 25 m/min In-feeding system EZ 14 Spraying unit (Anti-sticking liquid) In-feed fence, adjustable by N.C. Pre-milling Unit (vertical joint trimmers) 2 x Kw 3 Glueing Unit (P.U.R. Glue + Quick Melt system) Fpjdpfeyt Izbjx Ah Ajd Band Pressure zone, adjustable by N.C. Edge coils supporting unit (with No. 2 reels) Snipping (end-cutting) unit HL 84 (2 x Kw 0,5 ca.) Pneumatic swivelling and adjustment Rough Trimming unit BF 20 (2 x Kw 1,5 ca.) Multi Function Unit (Profile contour Trimming) FK 11 (2 x Kw 0,4 ca.) Profile edge scraping unit Finish processing unit (Glue scraper + Buffing unit) FA 11 Panels Return System "LIGMATECH" Mod. ZHR 541/L/095 (with Portal bridge and 360° rotating vacuum head)

Condition: good (used), Year of construction: 1998, 0.4-5 mm Workingpiece thickness from to 10-50 mm Total length 2730 mm Fodpfx Ahsx Tu Rdj Aspd Weight 720 kg

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, edge thickness (max.): 3 mm, feed rate X-axis: 25 m/min, rotational speed (max.): 12,000 rpm, TECHNICAL DETAILS Minimum edge thickness: 0.3 mm Maximum edge thickness: 3 mm Maximum feed speed: 25 m/min MACHINE DETAILS Edge Processing Unit 1 Unit: End Trimming Model: WK13 Fjdsytr Hbspfx Ah Aopd Number of motors: 2 Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 2 Unit: Top Milling Number of motors: 2 Motor power: 0.55 kW Max. speed: 12,000 rpm Edge Processing Unit 3 Unit: Multifunction Model: FK13 Number of motors: 2 automatic tool changer with NC positioning Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 4 Unit: Top Mill Model: UF11 Number of motors: 1 Motor power: 4 kW Max. speed: 9,000 rpm Edge Processing Unit 5 Unit: Edge Scraper Model: MN21 with NC positioning Edge Processing Unit 6 Unit: Glue Scraper Model: FA11 Edge Processing Unit 7 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Edge Processing Unit 8 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Total installed power: 35 kW EQUIPMENT Spray unit PowerControl PC22 machine programming software CE marking The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and descriptive technical/commercial data. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, safeguarding, and use of the machine at the destination. External reference: 6216

Condition: not inspected (used), Year of construction: 2004, functionality: unexamined, workpiece height (max.): 60 mm, workpiece width (max.): 2,800 mm, edge thickness (max.): 20 mm, controller model: IMATRONIC MT, The machine has the following configuration: Unit 1: Milling unit with CNC positioning Unit 2: Milling unit with NC positioning, hot melt adhesive tank, pre-press for hot melt adhesive Edge bonding + edge processing Unit 1: Edge banding machine (2 motors) Unit 2: Overlapping edge trimmer (2 motors) Unit 3: Edge trimmer (2 motors) Unit 4: Milling machine (1 motor) with automatic timer Unit 5: Milling machine (1 motor) with automatic timer Unit 6: Belt sanding machine (1 motor) Unit 7: Belt sanding machine (1 motor) Unit 8: Brushes (1 motor) TECHNICAL DETAILS Panel height min.: 8 mm Panel height max.: 60 mm Panel width min.: 280 mm Panel width max.: 2,800 mm Edge thickness min.: 0.4 mm Edge thickness max.: 20 mm Distance between feed tracks: 1,000 mm MACHINE DETAILS Control system: IMATRONIC MT EQUIPMENT CE marking Fpsdpfxoyttrxj Ah Aed The machine is sold and delivered in its actual and legal condition ('as seen and approved') on the basis of photo documentation and descriptive technical/commercial documents. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination location. External reference: 6561

Condition: not inspected (used), Year of construction: 2014, functionality: unexamined, power: 25 kW (33.99 HP), workpiece height (max.): 60 mm, edge thickness (max.): 12 mm, feed rate X-axis: 18 m/min, Equipment: CE marking, TECHNICAL DETAILS Minimum panel height: 8 mm Maximum panel height: 60 mm Minimum edge thickness: 0.3 mm Maximum edge thickness: 12 mm Maximum feed speed: 18 m/min Sequence of work steps: Section 1 Work step: Positioning Motor power: 2.5 kW Automatic control Edge preheater Glue tank Glue preheater Roll magazine Fpodpfx Ahsytr Rgo Asd Section 2 Work step: Cutting Number of motors: 2 Section 3 Work step: Edge milling Number of motors: 2 Motor power: 0.55 kW NC positioning Section 4 Work step: Corner rounding Number of motors: 2 NC positioning Section 5 Work step: Milling Number of motors: 1 Motor power: 3.5 kW Section 6 Work step: Edge scraping Section 7 Work step: Glue scraping Section 8 Work step: Brushing Number of motors: 2 MACHINE DETAILS Total power: 25 kW EQUIPMENT Panel support guide Spraying unit Control with more than 20 control systems CE marking The machine is sold and delivered in its actual and legal condition ('as seen and agreed'), based on photo documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 6216

Condition: ready for operation (used), Year of construction: 2005, Edgebander manufactured in 2005. This OTT Twister features a hot-cold melt adhesive application process and can handle edge thicknesses from 0.3 to 10 mm. It supports workpiece thicknesses of 8 to 60 mm and has a feed speed of 14-20 m/min. If you are looking to get high-quality edge banding capabilities, consider the OTT Twister edgebander we have for sale. Contact us for further details. • Adhesive application: Hot/cold melt adhesive process; application roller with synchronous and counter-rotation • Edge thickness: 0.3–10 mm • Workpiece thickness: 8–60 mm • Workpiece width: minimum 70 mm • Workpiece length: minimum 150 mm • Operating pressure: 6 bar • Feed power: 3.0 kW • Feed speed: 14–20 m/min • Electrical connection: 3x 400 V, 50 Hz • Extraction requirement: 1x Ø180 mm at 20 m/s = 35 m³/min • Air speed (minimum): 20 m/s • Compressed air consumption: approx. 300 l/minProcessing units / equipment on the machine: • Joining: • 2 x 2.2 kW, n=14,600, 250 Hz; two application-controlled working spindles • Combi-melt gluing unit: • Top-mounted, changeable hopper for EVA, PUR hot melt adhesive or cleaning granulates; hopper volume 2.5 l • AKM (automatic edge magazine): • Automatic edge magazine with optical monitoring for strip edges in fixed lengths Fjdpfx Ahoyn I U Rj Aspd • Capping: • 2 x 0.8 kW, n=12,000, 200 Hz; automatic swivel 0°/5°; 2 HM saw blades Ø140 x 3.2 x 16, z=34 • Flush milling: • 2 x 0.7 kW, n=12,000, 200 Hz; single-sided probing; 2 carbide-tipped indexable knife heads HF70, Ø70 x 20 x 16, z=4 • Fine milling (bevel 15°/30°/45°): • 2 x 0.3 kW, n=12,000, 200 Hz; double-sided probing; 2 carbide indexable insert cutter heads HF70, Ø70 x 20 x 16, z=4 • AWSR (radius R2–R5): • 2 quick-change sets for fine milling cutter, 2 x 0.3 kW; 2 carbide indexable insert cutter heads AR73 x 16 x 16, z=3, R2–R5 • AKF (copy milling): • Automated copy milling with two separate working spindles for end faces and longitudinal radii; 2 x 0.37 kW, 12,000 rpm; tools R1–R3 • Scraper blade: • 2 x carbide scrapers, automatic feed • Surface scraper: • 2 x carbide scrapers, with fine adjustment device • PU set: • 5-way spray device (2 x release agent, 1 x lubricant, 2 x cleaning agent), fine buffing device with cloth disc • Edge cleaning: • 2 x 0.2 kW, n=2,800, 50 Hz, oscillating brushes