Year of construction: 1990, condition: ready for operation (used), functionality: fully functional, controller manufacturer: Siemens, The system comes from current production. TECHNICAL DETAILS Screw diameter: 2 × 75.0 mm L/D ratio: 38 D Design: Co-rotating MACHINE DETAILS Control system manufacturer: Siemens Drive power: 180 kW Hjdoztw Agjpfx Aa Dst EQUIPMENT 2 dosing units Water bath Granulator Vacuum degassing Segmented screws and cylinder

Condition: used, Year of construction: 2001, machine/vehicle number: 21012101, functionality: fully functional, operating hours: 49,849 h, input voltage: 415 V, input current: 36 A, input frequency: 50 Hz, type of input current: AC, workpiece length (max.): 2,250 mm, workpiece width (max.): 1,500 mm, workpiece height (max.): 1,000 mm, workpiece weight (max.): 420 kg, number of axes: 5, number of slots in tool magazine: 10, controller manufacturer: Siemens, actuation type: electric, total height: 4,000 mm, total length: 7,300 mm, total width: 7,000 mm, table length: 2,250 mm, table width: 1,500 mm, control voltage: 24 V, 5-axis CNC machining center for wood or plastic. The machine was used for contour milling of plastic components. It is equipped with an HSD spindle, and the tool holder is of the HSK63 type. Hsdpfx Aajzhtpfe Djt The machine can be purchased with or without an extraction system, depending on the intended application. The dimensions specified for the machine include the extraction system. An inspection of the machine is possible at any time; it is currently still in production.

Condition: excellent (used), Year of construction: 1998, functionality: fully functional, clamping force: 500 kN, mold height (min.): 225 mm, ejector force: 300 N, overall weight: 2,450 kg, input voltage: 380 V, Equipment: documentation/manual, ARBURG 320 S in excellent condition, low operating hours, and with a Piovan dryer. Year of manufacture: 1998. Piovan dryer, model TDM604. Year of manufacture: 2005. Hjdozxg Amspfx Aa Djt Includes documentation. The machine is powered on for inspection.

Year of construction: 2013, operating hours: 7,700 h, condition: repair required (used), functionality: limited functionality, machine/vehicle number: 12090, This is a recycling extruder with side feeding for materials (flakes, pellets, etc.). The system is supplied with a control cabinet and a double vacuum system. The pelletizing system is missing at the end of the screw – it is not included in the scope of supply. The cylinder ends at the flange. The extruder is supplied without a screw. The frequency inverter for the main motor was replaced with a new unit 3 years ago. Installed power approx.: 474 kW Cooling water requirement approx.: 190 l/min Fresh water consumption approx.: 110 l/h Feeding system: • Diameter of the feeding screw: 200 mm • Drive for the feeding screw: 45 kW, frequency-controlled • Hopper capacity net 7 m³/250 ft³, • Gear motor 3 × 3 kW • 2 sight glasses in the hopper • 2 level indicators Extruder: • Diameter of the extruder screw: 145 mm • L/D ratio: 24 • Heating power: 50 kW • Extruder drive unit 280 kW Vacuum 1: • Screw length: 16 L/D • Heating power: 40 kW • Vacuum pump power: 11 kW • Vacuum capacity: 225 m³/h • Vacuum pressure: 33 mbar Vacuum 2: • Screw length: 16 L/D • Heating power: 40 kW • Vacuum pump power: 7.5 kW • Vacuum capacity: 190 m³/h • Vacuum pressure: 33 mbar Cylinder: • Cylinder: Bimetal extruder cylinder, • Reinforcement layer 1.8–2.0 mm thick, • Hardness 63–65 HRC Installation conditions: • Voltage: 3 × 400 Volts • Permissible fluctuation max.: +5 % – 5 % • Frequency: 50 Hz Permissible fluctuation max.: +4 % – 4 % • Protective measure: Multiple grounding • Ambient temperature: min. 15 °C, max. 35 °C • Humidity max.: 90 % • Altitude of the installation site: 0 – 1000 m The machine was in operation at an R&D center in Israel. Since the company now operates a production facility in Europe, the R&D center is being closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production facility in Europe. Hsdpfx Asznz Ezsa Dst The details for optimal transport need to be clarified. The machine price is without packaging.

Condition: like new (used), Year of construction: 2006, operating hours: 4,545 h, functionality: fully functional, screw diameter: 114 mm, overall weight: 7,500 kg, A KMD114-32 P in like-new condition is for sale. This extruder comes from a technical institute and is therefore from a single owner. Hedpfx Aezxhfioa Dst The operating hours are original and can be verified. The screw and cylinder are in like-new condition. The gearbox runs very smoothly. Includes adapter, hopper, and loading onto a truck. Technical specifications: - Year of manufacture: 2006 - Screw for profile: 684 2929 / 8880 - Internal screw temperature control, welded tips - Maximum screw speed = 17 min-1 - Maximum dosing speed = 260 min-1 - 5 cylinder zones, 15 tool zones + 4 lip heaters, melt temperature, melt pressure - C5 control system with puller control, language E/D An inspection in 84405 Dorfen is possible at any time. If you have any questions, please do not hesitate to contact us.

Condition: used, Year of construction: 1998, operating hours: 93,000 h, functionality: fully functional, machine/vehicle number: 174380, clamping force: 2,000 kN, screw diameter: 60 mm, clearance between the columns: 560 mm, mold height (min.): 1,050 mm, input frequency: 50 Hz, input voltage: 400 V, input current: 222 A, Equipment: documentation/manual, For sale: 200-ton Krauss Maffei injection molding machine. The machine is currently in production and can be inspected while in operation. Distance between columns (H x V): 560 x 560 mm Platen size: 915 x 915 mm Max. open height: 1050 mm Min. mold height: 350 mm Opening stroke: 700 mm Hjdpfx Aaszwwyaj Dot

Condition: used, Year of construction: 2010, functionality: fully functional, Technical specifications: System output: up to approx. 2,000 cuts per 8 hours, depending on the cross-sections of the reinforcing bars used Feed magazine: 12 positions, automatically timed Discharge magazine: 12 positions, automatically timed Bar length, maximum: 6,000 mm Bar length, minimum: 400 mm Cutting length, maximum: 4,000 mm Cutting length, minimum: 170 mm Remaining piece processing: 350 mm Profile dimensions: 86 × 70 mm Wall thickness, maximum: 3 mm Functionality and features: • Saw unit with spray medium system • Automatic operation • Lateral discharge in the Z-direction • Screen-based dialog system with loading table display • Direction of travel, depending on the model, from left to right or from right to left Control and hardware configuration: • High-quality PC with a 19-inch TFT color monitor • USB ports • DVD drive Hodpfx Aaszm I Dhj Djt • Keyboard • Windows operating system • Remote maintenance via the internet

Year of construction: 1981, condition: used, functionality: fully functional, machine/vehicle number: 8890/81, For sale is a rubber screw extruder from TROESTER. Technical data can be found in the photo. The extruder is in perfect working order and can be put into operation immediately without any problems. A spare spindle is available. Please feel free to contact us if you have any further questions. Transportation must be arranged by the buyer. Hodpfezxa Ehox Aa Dst The location is in 22145 Braak.

Condition: used, Year of construction: 2019, functionality: fully functional, clamping force: 2,500 kN, total width: 12,500 mm, total length: 11,500 mm, total height: 8,600 mm, power: 831 kW (1,129.84 HP), Equipment: documentation/manual, For sale is a highly automated BBM 2500 CoEx3 extrusion blow molding machine, manufactured in 2019. The machine is in very good technical condition, fully functional, and immediately available. An inspection while the machine is running can be arranged by appointment. The machine is designed for the economical production of large-volume HDPE hollow bodies and sophisticated technical blow-molded parts. It is a batch-type 3-layer extrusion blow molding machine with a parison accumulator head. The offered scope of supply includes: - Piovan GMS-160 high-performance plastic granulator, manufactured in 2023 - Piovan VM 500 extraction system - GWK/Technotrans cooling unit The listed peripheral components are included in the offer price. If individual components or the entire range of accessories are not required, they can be removed from the scope of supply, and this will be taken into account when determining the price. Technical key data: Manufacturer/Model: BBM 2500 Year of manufacture: 2019 Process: CoEx3 extrusion blow molding with parison accumulator head Material: HDPE Design: 1 station with 1 CoEx3 blow head 3 extruders: 1 × 130 mm and 2 × 70 mm Total output: up to 1,200 kg/h Accumulator volume: 1 × 20 l and 2 × 7.5 l Electrical wall thickness control Clamping force: 2,500 kN Platen area: 2,160 × 2,400 mm Column spacing: 1,500 × 2,400 mm Opening width: 600–1,500 mm Electrical closing movement Locking via 6 hydraulic power strokes 2 integrated KUKA 6-axis robots for removal and handling Hsdpfx Ajzw D Haea Djt Fully automatic KOCH material feeding system with gravimetric dosing and mixing Beckhoff TwinCAT control with Siemens components and drives Connected power: 831 kW Power supply: 400 V, 3 phases/N/PE, 50 Hz Dimensions: approx. 11,500 × 12,500 × 8,600 mm (L × W × H) CE documentation and machine manuals available The machine is particularly suitable for large-volume hollow bodies, technical molded parts, infrastructure products, sanitary parts and industrial containers. Availability: immediate Inspection and trial run: possible by prior appointment

Condition: like new (used), Year of construction: 2019, operating hours: 11,337 h, functionality: fully functional, machine/vehicle number: 234917, clamping force: 1,600 kN, screw diameter: 30 mm, Equipment: documentation/manual, ENGEL eMotion 160 from a cleanroom injection molding facility, with only 11,300 operating hours and in like-new condition. The machine was used for the production of 64-cavity pipette molds at NYPRO (Jabil) in Knittlingen and is in like-new condition. This is the last available unit from an original total of 90 machines. It was originally intended for another NYPRO plant but has now been released for sale as part of a site relocation. Hodpewb Dl Tsfx Aa Dot • The order confirmation from ENGEL to NYPRO can be found in the documents. The original new price was approximately €330,000. The selling price is €78,500 including crane. I can provide you with the technical data upon request, but it is also available in the documents below. Included in the price: Dismantling the crane onto two Euro pallets, as well as removing the machine from the cleanroom and loading it onto your truck using a 15-ton forklift. If you are interested or have any questions, please do not hesitate to contact me. The machine is located near Karlsruhe and can be inspected there. Delivery is possible within a few days. You can find the order confirmation from ENGEL to NYPRO in the documents below!

Condition: ready for operation (used), Year of construction: 1999, functionality: fully functional, power: 7.5 kW (10.20 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: AC, overall weight: 500 kg, Plastic shredder, motor: 7.5 kW, speed: 1,400 rpm, feed opening: 300 x 260 mm. Hjdpfjzab Tdox Aa Dst

Condition: used, Year of construction: 1998, functionality: fully functional, machine/vehicle number: 173340, clamping force: 2,000 kN, screw diameter: 50 mm, clearance between the columns: 520 mm, plate length: 715 mm, plate height: 715 mm, total length: 5,360 mm, total width: 1,800 mm, total height: 2,200 mm, overall weight: 6,900 kg, Equipment: documentation/manual, ARBURG ALLROUNDER 520 C 2000-675, hydraulic injection molding machine for plastics, year of manufacture 1998. The machine has a clamping force of 2,000 kN (200 tons) and an injection unit with a 50 mm diameter screw. Technical data: Manufacturer: ARBURG Hsdszw Hnyopfx Aa Dst Model: ALLROUNDER 520 C 2000-675 Year of manufacture: 1998 Clamping force: 2,000 kN / 200 tons Injection unit: 675 Screw diameter: 50 mm Distance between columns: 520 × 520 mm Platen size: approximately 715 × 715 mm Opening stroke: approximately 650 mm Control: SELOGICA Condition: The machine was dismantled in perfect working order and is sold in its current condition. Operating hours are not available. The machine is available for viewing/inspection by appointment. Sale includes the injection molding machine only. The Cartesian robot and other components of the cell can be purchased separately.

Condition: used, Year of construction: 2007, functionality: fully functional, SE-HSM-40/26-COMPACT-PLUS Horizontal four-head welding machine 2MC Horizontal CNC corner edging machine, motion control WST-30 Horizontal turning station Minimum element size 320 × 320 mm Hedpfx Aezm N Nroa Det Maximum element size 4,000 × 2,600 mm Maximum element weight 80 kg Minimum working area 320 × 320 mm Maximum working area 4,000 × 2,600 mm

Condition: like new (used), Year of construction: 2012, functionality: fully functional, machine/vehicle number: 105-337, Machine for cleaning the corners of PVC profiles. Hodpfxozdqago Aa Dot

Condition: excellent (used), Year of construction: 2009, clamping force: 3,000 kN, screw diameter: 65 mm, clearance between the columns: 710 mm, injection pressure: 2,070 bar, injection weight: 981 g, mold height (min.): 225 mm, Clamping Unit • Clamping force: 3000 kN (300 t) • Distance between columns: 710 x 710 mm – special design, increased distance compared to the standard version • Mold height: min. 225 mm / max. 1125 mm • Opening stroke: 900 mm • Maximum distance between mounting plates: 1125 mm • Mounting plate size: 1030 x 1020 mm (920 mm) • Special hole pattern in the clamping plate and nozzle plate – made to order • Manual device for removing the upper column, with a removable cover in the front guard and a wrench for the column nut Injection Unit • Injection unit 2250 • Screw diameter: 65 mm, L/D ratio 22.0 • Shot volume: 1078 cm3 • Maximum injection weight (PS): 981 g • Specific injection pressure: 2070 bar • Equipment package: wear and corrosion-resistant plasticizing unit, adapted for processing PP and PPSU, diameter 65 mm • Hart-PVC package: without internal screw cooling, with external cylinder cooling instead of standard design • High-temperature heating bands for a working temperature of 450 °C • 8 standard open nozzles, plus: 4 for the PVC cylinder and 4 for the PP cylinder, through holes 4, 8, 10, and 12 mm • Wrench for screw tip for a 65 mm diameter UNILOG B6S Control System - Upgrade package • Controller with increased computing power • APS and cycle time analysis • Four freely configurable network connections Hedjzxfg Rjpfx Aa Det • Userpage and notepad • Real-value graphics with 16 curves • Event log depth: 10,000 events • Quality table memory depth: 10,000 events • Four envelope curves, foil function keys • SPC evaluation and trend charts • Injection, holding, and back pressure controlled by a servo valve Hydraulics and Hydraulic Cores • Core movement and parallel ejection are performed by an additional DFEE pump, size 71, flow rate 95 l/min • 4 x hydraulic core for the clamping plate NW 10 (on/off valve), interfaces according to EUROMAP 13, with active ejector plate protection • Cores mounted on the upper side of the clamping plates, each with connections for two consumers • 2 x core junction box in a special design: 25 3-pole Amphenol plugs, mounted on the clamping plate on the operator side and the rear side, connected in series • 4 x core pressure relief upon emergency shutdown, engine stop, and after pressing the button in setting mode – relief occurs simultaneously for cores on the clamping side and the nozzle side • 4 x twin check valve for NW 10 core • 2 x pneumatic valve for controlling one closing nozzle in the mold or several in parallel (1000 l/min), mounted in the center console at the rear of the machine Mold Heating, Electrical System, and Connections • 12 x temperature control circuit for hot runner or mold heating, power 2.3 kW, 10 A, interface according to HASCO standard (1 x HASCO 24-pole for max. 6 zones) • Mounting location for heating circuits: center console at the rear, near the control cabinet • 2 x Schuko 16 A socket: under the control system and on the clamping side from the rear, under a cover • 2 x CEE 16 A socket: on the injection side from the front and on the clamping side • Dual power supply: 1. power supply 3P+N, 400 V, rated current 140 A, preliminary protection gL-gG 160 A • 2. power supply 3P, 400 V, rated current 98 A, preliminary protection gL-gG 100 A

Condition: excellent (used), Year of construction: 2010, clamping force: 1,000 kN, screw diameter: 45 mm, clearance between the columns: 470 mm, injection pressure: 1,580 bar, injection weight: 232 g, mold height (min.): 250 mm, Clamping unit • Clamping force 1000 kN (100 t) • Set of mounting plates, central mounting, 125 mm bore • Electromechanical ejector • Quick-release coupling for the ejector • Connection safeguard for the ejector plates • Programmable mold height adjustment from the operator panel • Top-open guard with a drop-down window for the parts removal device Injection unit • Complete 45 mm screw with high wear resistance • Open nozzle 45 mm, nozzle tip with a 15 mm radius, heating band for open nozzle • Nozzle clamping force adjustable and programmable • AED - electromechanical dosing drive • aXw Control ScrewPilot Drive system - HIDRIVE hybrid • H series: hybrid concept combining electric drives with accumulator hydraulics • Drive unit with 11 kW motor, 21.4 l/min charging capacity • Technology level: accumulator drive – fast movements with low power consumption • Continuous oil cooling and filtration • Hydraulic accumulator tested during start-up Control system • Selogica direct with touchscreen • Complete set of six software packages: extended monitoring, extended movements, production control, optimization and operator assistance, quality assurance, documentation • Printer interface, serial USB • CompactFlash interface for saving data sets • Operator authorization via chip card according to EUROMAP 65 Hjdpfozxg Txsx Aa Djt Hydraulic cores • Core 1 – simultaneous movement, P/Q regulation, programmable • Core 2 – simultaneous movement, P/Q regulation, programmable • Both circuits are fully integrated with the Selogica cycle sequence and controlled directly from the panel • Note regarding connections: the machine was delivered from the factory without standard quick-release couplings for the core circuits. Stäubli SBA 08.7103/JV/PA couplings/nipples with a G1/2 connection thread are required.

Year of construction: 2022, condition: like new (used), year 2022 Robot ABB type IRB 120, variant IRB 120/3/0,6 Weight of robot 25 kg payload 3 kg Hodpfx Aszw D Ausa Dot 6 axis robot box IRC 5 Compact, version 58A 262V, weight 30 kg

Condition: good (used), Year of construction: 2008, machine/vehicle number: 3514, functionality: fully functional, power: 25 kW (33.99 HP), input voltage: 400 V, total length: 5,000 mm, total width: 2,000 mm, total height: 2,500 mm, overall weight: 3,000 kg, KOCH CKT-300 Granulate Drying System - including piping and 6 associated containers Note: The item must be picked up on a fixed date between September 1st and September 3rd, 2026; the exact date will be confirmed. Hedpfszvl H Sex Aa Djt FCA D-58507 Lüdenscheid - loaded onto a truck.

Condition: used, Year of construction: 2016, Manufacturer: KRAUSS MAFFEI, Type: KM 850-6100/1400 MXZ Blue Power, Year of manufacture: 2016, Serial number: 61024868, Control system: Krauss Maffei MC5, Clamping force: 850 t, 2 injection units, Rotary table, Installation height min./max. 500/960 mm, Daylight opening 1,120 mm, 48 hot runner nozzles, hydraulic core pull systems 2 (DS) 3 (AS), Screw diameter 95/60 mm, Shot weight 3,200/500 g, Parts removal robot, Manufacturer: Krauss Maffei, Type LRX350, Year of manufacture: 2016, Serial number: 2114889, Conveyor belt, 3,000 x 800 mm Hedpfx Aajzn Ap Ie Det 37,544 hours (25,846 net production hours) Note: Machine is part of an online auction!

Condition: used, Year of construction: 2005, Manufacturer: KRAUSS MAFFEI, Type: 1600-8100-1400MX, Year of manufacture: 2005, Serial No. 61007140, Control system: Krauss Maffei MC5, Clamping force: 1,600 t, 2 injection units, Minimum/maximum mold height: 700/1,600 mm, Platen spacing: 3,400 mm, Clear opening horizontal/vertical: 1,850/1,400 mm, 12 cascades, 48 hot runner nozzles, Core pulls hydr. 5 (DS) 5 (AS), Screw diameter: 105/60 mm, Injection weight: 4,100/600 g, Part removal robot, Manufacturer: Krauss Maffei, Belt conveyor, approx. 5,000 x 1,400 mm Hjdpfx Aaozn Aqfs Det +++ Attention: Machine is part of an online auction! +++

Year of construction: 2020, condition: excellent (used), Fine impact mill, hammer mill, pin mill, pulverizer, side mill, granulator, shredder, powder mill, granulate mill, granulator, rotor mill, recycling technology, agglomerator -Condition: The machine was a demonstration unit, equipped without a control system. -Manufacturer: WIPA, Hammer mill -Type: WPZ 750-45 -Drive motor: 45 kW -Number of mallets: 4 pieces -Number of counter blades: 6 pieces -Ejection: Height adjustable Quantity: 1 piece available -Dimensions: 1730/220/H3200 mm Hedpfx Ajzbk Iysa Det -Transport dimensions: 1370/220/H1730, 1400/800/H1470 mm -Weight: 1900 kg

Condition: used, Year of construction: 2010, machine/vehicle number: 2067, functionality: fully functional, power: 6.5 kW (8.84 HP), input voltage: 400 V, input current: 20 A, input frequency: 50 Hz, type of input current: AC, total height: 2,000 mm, total length: 1,500 mm, total width: 2,000 mm, overall weight: 750 kg, Equipment: CE marking, documentation/manual, TARTLER NODOPUR VS-AR-2K – 2-Component Metering and Mixing System – Year of Manufacture 2010 – For sale is a used 2-component metering and mixing system, TARTLER NODOPUR VS-AR-2K. It was used in an industrial setting and shows corresponding signs of wear. Technical data: • Manufacturer: Ing. Büro Tartler GmbH / TARTLER • Type: NODOPUR VS-AR-2K • Machine No.: 2067 • Year of Manufacture: 2010 • Operating Voltage: 400 V AC • Frequency / Current Consumption: 50 Hz / 20 A • Power according to nameplate: 6.5 kW • Operating Pressure according to nameplate: 6–8 • Dimensions: approx. 1,500 × 2,000 × 2,000 mm incl. refill system • Weight: approx. 750 kg, depending on the equipment Control / Drive • Siemens PLC / SIMATIC Panel MP377 • Frequency Inverter A/B: Lenze, 1.50 kW • Drive Motor A/B: 1.50 kW • Mixing Head Type: LC 6/3 • Electric Motor Mixing Head: Emod, 1.1 kW Metering Technology Component A • Metering Pump: KTS 32 • Delivery Volume: 32 cm³ / 30 ccm/stroke • Volumetric Meter: VSI 0.1/16 EPC S4V Component B • Metering Pump: FPN 16.0 • Delivery Volume: 16 cm³ / 16 ccm/stroke • Volumetric Meter: VSI 0.2/16 EPO 12 V Containers / Material Supply • 1 × Stainless Steel Container A, approx. 60 liters • 1 × Stainless Steel Container B, approx. 60 liters • Containers with Mini-/Maxi-Level Monitoring • Container Pre-Pressurization • Silica Gel Filter • Container Agitator • Automatic Refill from 200-Liter Containers • Diaphragm Pumps for Component A and B Hose Assembly • Component A: approx. 6.12 m / DN 16 • Component B: approx. 6.42 m / DN 10 Equipment: The equipment includes, among other things: • Metering and mixing system for two components • Mixing head • Siemens control panel • Metering pumps A and B • Volume flow measurement • Stainless steel material containers • Agitators • Automatic refill system • Diaphragm pumps • Hose package • Signal light / Traffic light • Control cabinet • Various sensors and pressure regulators Condition: The system is in used condition. Age- and use-related signs of wear as well as material residues are present. The optical condition can be clearly seen in the current photos. Hedpfezvmihjx Aa Djt An inspection of the system is possible after prior appointment. A function test can also be carried out after consultation. Sale: Price: €17,500 (negotiable) plus VAT. Inspection and collection by appointment. Sale preferably to commercial businesses. If you are interested or have technical questions, we will be happy to send you further pictures and information.

Condition: excellent (used), Year of construction: 2021, operating hours: 3,500 h, functionality: fully functional, machine/vehicle number: 2021-1504-QN, High-end metal separator for inspecting bulk materials in free fall Material: stainless steel 304 Surface: sandblasted Sensing tube material: PE, anti-static, food grade Rejector: single flap type RH Protection rating: IP66 Electronics assembly: detached Control electronics cable length: 3 m Nominal width: 150 mm Orientation: vertical, top to bottom Power supply: 100-240VAC 50-60Hz LNPE - Without power cable Pressurized air supply: 6-10 bar Expected sensitivity: FE: 0.4 mm NE / Al: approx. 0.4 to 0.56 mm Hsdpfx Aaszvwlme Dst Stainless steel: approx. 0.4 to 0.72 mm Electronics outside ATEX Zone Inside: Zone 20 within metal separator (pipe) = II 1 D Ex h IIIC T135°C Da Outside: Zone 22 surrounding metal separator = II 3 D Ex tc IIIC T135°C Dc IP65 QUICKTRON 07 RH metal separators are used for inspecting powders and granules in free-fall lines. They are available in nominal widths up to 300 mm and can therefore cover all application areas, from the laboratory to truck loading. Their hygienic design and easy cleaning prevent cross-contamination between product batches. Depending on the requirements, they can increase process safety or fulfill the task of outgoing goods inspection. Mesutronic metal detectors use state-of-the-art technology to protect your production, your reputation, and your customers from damage caused by metallic foreign objects. Digital signal processing, combined with innovative evaluation methods, comprehensive self-monitoring, and ease of operation, ensure the optimal function of the system and the successful completion of all types of audits. The devices are complemented by an extensive range of accessories and variants, from multi-frequency technologies to test bodies and material certificates. The machine was in operation at an R&D center in Israel. As the company now operates a production facility in Europe, the R&D center will be closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or in the production plant in Europe. The details for optimal transport need to be clarified. The machine price does not include packaging.

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, machine/vehicle number: 8Q00001264, For sale is a powerful and precise Wittmann linear robot W822-1264 for injection molding applications and automation tasks. The unit is packaged and secured on a Euro pallet and comes with the matching handheld device (teach pendant), emergency stop buttons, cabling, and the original technical documentation. The unit is in good condition and fully functional after disassembly. Technical data (according to the nameplate): Manufacturer: Wittmann Kunststoffgeräte GmbH (Vienna, Austria) Model / Type: W822-1264 Article number: 8Q00001264 Year of manufacture: 2015 Payload: 15 kg Travel distances / stroke (X / Y / Z): X-axis (ejection stroke): 550 mm Y-axis (vertical stroke): 1200 mm Z-axis (lateral stroke / main axis): 2500 mm Supply voltage: 360V – 400V (50/60 Hz, 3PH/N/PE) Connected load: 1.9 kVA Weight: 275 kg Scope of supply & components: - Main unit / linear robot Wittmann W822-1264 - Pneumatic / gripper head with C-axis / swivel function and pneumatic valve blocks (SMC). - Including energy chains / drag chains for organized cable and hose routing. - Control system & operating unit - Original Wittmann Teachbox R8 / touch-screen handheld device with protective housing. - Additional handheld unit with emergency stop switch and function buttons. Hsdpozu Rzfjfx Aa Det - External button boxes / control elements (including EMERGENCY STOP, quality control part, etc.). - Complete cabling, oil cooler control lines, Harting multi-pin connectors, and pneumatic hoses. - Original folder "Wittmann Technical Documentation" (including circuit diagrams, operating manual, and documentation). Upon request, transport and loading can be arranged for an additional fee, throughout Europe. Prices plus VAT. Inspection possible by appointment. Contact us, our team will be happy to assist you further. Trade-in or exchange possible! Machine purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES, ETC. Do you need a high-quality but affordable metalworking machine for your production? Or do you want to sell yours? For further information or contact options, visit our website.

Condition: excellent (used), Year of construction: 2017, operating hours: 2,000 h, functionality: fully functional, machine/vehicle number: 2017.041.XM.400.004, space requirement length: 6,700 mm, space requirement width: 3,200 mm, space requirement height: 5,000 mm, This is a combination of a hot mixer and a cooler. A typical application is mixing polymers with additives. Hot mixer: working volume of 400 liters, drive power 90 kW, mixing impeller with a tip speed of up to 60 m/s. Vacuum system included (but needs optimization). Filling hopper included. Gravimetric scales for the additives are not included in the delivery. Cooling mixer, volume 1200 liters with a 11 kW drive, cooling jacket for cold water flushing, outlet with a valve. The combination includes the entire steel structure with walkways, control cabinet with frequency converter (400 VAC/50Hz) for the variable drive of the hot mixer. Additional documents can be provided upon request. The machine was in operation at an R&D center in Israel. Since the company now operates a production facility in Europe, the R&D center will be closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production facility in Europe. The details for optimal transport need to be clarified. The machine price is quoted without packaging on a pallet. Hsdpfxjzl Td Rj Aa Dst