Condition: used, Year of construction: 2003, CLAMPING UNIT Clamping force: 2000 kN Locking force: 2200 kN Max. opening stroke: 575 mm Min. mould height: 310 mm Max. mould height: 660 mm (760 mm with WA) Max. distance between platens: 1235 mm (1335 mm with WA) Platen size (H x V): 830 x 830 mm Distance between tie bars (H x V): 560 x 560 mm Max. mould weight: 2500 kg Max. mould weight on moving platen: 1700 kg INJECTION UNIT (120) Screw diameter: 30 mm L/D ratio: 20 Injection pressure: 2420 bar Stroke volume: 124 cm³ Shot weight (PS): 110 g Max. dosing stroke: 175 mm Max. nozzle stroke: 350 mm Nozzle penetration depth: 40 mm (30 mm with SPI) Nozzle contact force: 80 kN Barrel heating power: 7.9 kW Electric screw drive (WA): 12.6 kW Hopper capacity: 70 l INJECTION UNIT (840) Screw diameter: 50 mm L/D ratio: 20 Injection pressure: 1946 bar Stroke volume: 442 cm³ Ibjdpfx Ajz D U D Tsd Noc Shot weight (PS): 400 g Max. dosing stroke: 225 mm Barrel heating power: 14.8 kW Electric screw drive (WA): 20.5 kW Hopper capacity: 70 l

Year of construction: 2020, condition: excellent (used), Fine impact mill, hammer mill, pin mill, pulverizer, side mill, granulator, shredder, powder mill, granulate mill, granulator, rotor mill, recycling technology, agglomerator Isdpjzbk Iysfx Ad Nobc -Condition: The machine was a demonstration unit, equipped without a control system. -Manufacturer: WIPA, Hammer mill -Type: WPZ 750-45 -Drive motor: 45 kW -Number of mallets: 4 pieces -Number of counter blades: 6 pieces -Ejection: Height adjustable Quantity: 1 piece available -Dimensions: 1730/220/H3200 mm -Transport dimensions: 1370/220/H1730, 1400/800/H1470 mm -Weight: 1900 kg

Condition: used, Year of construction: 2010, Injection moulding machine Arburg 370H 600-290, year 2010, incl. Wittmann picker Injection moulding machine Arburg 470C 1500-400, year 2006, incl. Wittmann handling Iedpoy R Tg Esfx Ad Nsbc

Condition: used, Year of construction: 2008, 4 x Arburg injection molding machines Arburg injection molding machine 470C 1500-400, year of manufacture 2008 Arburg injection molding machine 270M, year of manufacture 1995 Ijdpfx Adozclpzo Nsbc Arburg injection molding machine 270S 500-150, year of manufacture 2004 Arburg injection molding machine 320M 750-210, year of manufacture 1998

Condition: used, Year of construction: 2019, Injection molding machine Demag EL Exis SP 1000/1195-6300, year of manufacture 2019. Iedpfxozxxhue Ad Nebc

Condition: used, Year of construction: 1999, Injection molding machine Arburg 1500 T, 2-component, year of manufacture 1999. Ibedpfxoz Dufqe Ad Nec

Condition: used, Year of construction: 1999, Injection moulding machine Krauss-Maffei 800 /5700MC, year 1999, for sale. Technical specifications available on request. Iedpfx Adjyg Hbgo Nobc

Condition: excellent (used), Year of construction: 2022, operating hours: 1,000 h, functionality: fully functional, machine/vehicle number: SN210551, overall weight: 14,000 kg, type of input current: AC, input voltage: 400 V, power: 400 kW (543.85 HP), Equipment: type plate available, A MIXACO heating/cooling mixer is a combined system consisting of a heating mixer and a downstream cooling mixer, specifically designed for the processing of powders, granules, and compounds (e.g., PVC dry blends, WPC, or masterbatches). Ibsdsz Iww Rspfx Ad Nec Technical specifications – summary (details can be found in the documents): Hot mixer: • Volume: 3500 liters – Usable volume: 2500 liters • Tip speed: 5-50 m/s • Made of duplex steel – 1.4462 stainless steel • Power drive with 400 kW FC controlled • Vacuum up to 150 mbar abs. Cold mixer: • Volume: 9000 liters – Usable volume: 7650 liters • Tip speed: 3.5 – 7 m/s • Made of 1.4541 stainless steel • Power drive with 90 kW FC controlled The operating principle is divided into two physically and apparatus-wise separate process phases: 1. The heating mixer phase (heating and homogenizing) • Mechanical friction: In the heating mixer, a modular mixing tool rotates at a high circumferential speed (approx. 10–40 m/s). The intense flow and vortex formation (mixing vortex) causes the particles of the mixture to rub intensely against each other. • Heating: This mechanical friction generates the necessary thermal energy directly in the product, quickly and evenly heating the material to the desired target temperature (sometimes exceeding 100 °C). • Recipe component addition: At the same time, all recipe components, such as additives, dyes, or liquids, are perfectly homogeneously distributed. An integrated aspiration system also ensures the dehumidification of the mixture. 2. The transfer • Once the target temperature defined in the process program is reached, a contoured, dead-space-free outlet opens on the heating mixer. • The hot, homogeneous mixture is transferred with minimal residue and quickly to the cooling mixer, which is located directly below or next to it. The heating mixer is then immediately available for the next batch. 3. The cooling mixer phase (gentle cooling) • Heat exchange: In the cooling mixer (available in vertical or horizontal design), the hot material is passed over cooled surfaces. • Water cooling: A targeted cooling water circuit in the double jacket (bottom and side walls) efficiently removes thermal energy from the dry blend. • Agglomeration prevention: A slow, material-friendly stirring mechanism keeps the mixture in motion until the final storage temperature is reached. This prevents caking (compaction) due to residual heat before the material is transferred to silos or further processing. Summary created with AI. The units can be inspected in operation in the Netherlands. The system for sale was used in the R&D center of UBQ for development purposes. This explains the very good condition for the low number of production hours. We also have a steel structure available for the setup. This is not included in the price. If there is interest, it can be negotiated separately. Currently, the system is located outside of Europe – we need to determine whether direct transport is feasible or whether import to Europe by UBQ is more sensible (which would allow for a sale within Europe with a reverse-charge mechanism).

Condition: used, DEMAG Ergotech System 650/1000-3300 with 6,500 kN clamping force and 3300 Euromap injection unit, equipped with a 2021 Wittmann W843 pro robot featuring servo B axis 270° and servo C axis 180°. The machine delivers 1,600 g shot weight through an 80 mm screw, supported by 4 hydraulic core pulls, 8 cascade circuits, and 16 hot runner zones for complex multi-component and technical moulding. CNC CONTROL Controller: Demag Ergocontrol CLAMPING UNIT Clamping force kN: 6.500 Tie-bar clearance (H x V) mm: 1.000 Iedpfx Aszz S Uaod Njbc INJECTION UNIT Injection unit size (Euromap): 3300 Screw diameter mm: 80 Max. shot weight (PS) g: 1.600 MOULD FUNCTIONS & HANDLING Hydraulic core pull circuits: 4 Cascade / valve gate circuits: 8 Hot runner control zones: 16 Handling robot (model / year): Wittmann W843 pro (2021) Robot strokes X / Y / Z mm: 1.200 / 2.000 / 3.000 Robot rotary axes (B / C): C servo 180° / B servo 270° DRIVE Max. hydraulic pressure bar: 190 Mains connection V / Hz / A: 3 x 400 / 50 / 241 + 108

Condition: excellent (used), Year of construction: 2017, clamping force: 2,000 kN, Equipment: documentation/manual, Clamping force: 200 t Screw diameter: 50 mm Shot weight: 359 g Distance between tie bars V: 570 mm Distance between tie bars H: 570 mm Shot volume: 392 cm3 Ibsdpfx Adjz Aty He Nsc Injection pressure: 2000 bar Euromap 67 1x core puller Type: Horizontal Drive: Hydraulic

Condition: used, Universal temperature control unit REGLOPLAS Type 90M/10/SG75/D K/RT50 Pressurized water temperature control unit with electric heating and connections for external cooling Circulating process temperature control for industrial applications in plastics processing, especially for the temperature control of injection molds and other process tools. Manufacturer's serial number: 102010170001, Year of manufacture: 2009 Temperature: max. 90°C (for water) Heat transfer medium: Water Temperature range: +20°C to 90°C Operating overpressure: max. 6 bar Pump capacity: 100 l/min Tank volume: 2.8 liters (internal filling volume) Iodpfxoz Au Hbs Ad Nsbc Heating capacity: 10 kW Cooling capacity of heat exchanger: up to 160 kW (depending on the external cooling unit) Pump motor power: 1.5 kW Continuous sound pressure level

Condition: used, Year of construction: 2008, operating hours: 75,874 h, Compact hydraulic injection molding machine from KraussMaffei with MC5 control system and extensive peripherals. Ijdpfoz Au Hzsx Ad Nobc Manufacturer: KraussMaffei Machine type: Injection molding machine Model: KM 65-380 CX International size designation: 380 CX/65 Year of manufacture: 2008 Machine No.: 61011979 Clamping force: 650 kN Tie bar distance: 420 × 420 mm Max. mold opening stroke: 500 mm Min. mold mounting height: 250 mm Max. opening width: 750 mm Ejector stroke: 150 mm Control system: KraussMaffei MC5 Machine weight: 3,900 kg Operating voltage: 400 V Frequency: 50 Hz Fuse rating: 160 A Total current: 143 A Motor current: 37 A Peripherals: Frigel Microgel process cooler Frigel model: RCD80/12HHP Year of manufacture of cooler: 2014 Refrigerant: R407C Refrigerant quantity: 2.4 kg Cooling medium: Water Temperature range: -5 to +90 °C Max. pressure: 8 bar Weight of cooler: 240 kg Further visible peripherals: Distributor chute from M Fördersysteme, year of manufacture 2002 Equipment: Material/parts handling and additional process peripherals as shown in the images. Location: Freiburg Available from APRIL 2027

Condition: like new (used), Year of construction: 2019, clamping force: 500 kN, Equipment: documentation/manual, _ENGEL – Injection Moulding Machine Technical Data_ Serial number: 232665 Model: E‑VICTORY _Plasticising Unit 1_ • Screw diameter: 18 mm • Listed diameter options: 15 / 18 / 20 mm; 18 mm is installed • Screw stroke: 80 mm • Maximum injection volume: 20 cm³ • Screw speed: 450 rpm • Screw torque: 75 Nm • Plasticising rate, 3-zone screw: 4.2 g/s _Injection Unit 1_ • Version: Standard • Injection rate: 83.97 cm³/s • Specific injection pressure, regenerative mode: 2,400 bar _Nozzle 1_ • Nozzle stroke: 210 mm • Nozzle contact force: 40.6 kN _Material Cylinder 1_ • Screw L/D ratio: 24 Iedpfx Adjz Iylds Nebc • Heating zones, including nozzle: 4 • Heating power: 5.1 kW • Note: maximum available equipment _Clamping Unit_ • Clamping force: 500 kN (approximately 50 tonnes) • Opening stroke + cylinder tolerance: 408 mm • Maximum distance between platens: 600 mm • Minimum mould height: 200 mm • Platen dimensions, horizontal × vertical: 500 × 450 mm • Drop-out chute width: 400 mm • Maximum mould weight on moving platen: 300 kg • Maximum mould weight on stationary platen: 300 kg • Maximum total mould weight: 600 kg • Dry-cycle stroke according to Euromap 6: 150 mm • Dry-cycle time according to Euromap 6: 1.60 s Mould weight notes: 1. Mould overhang according to mounting platens. 2. Less the weight of any rotary table. _Ejector 1_ • Ejector stroke: 100 mm • Ejector force: 39.8 kN _Drive Unit_ • Oil reservoir capacity – injection unit, main tank: 135 l • Oil reservoir capacity – clamping unit, auxiliary tank: 0 l _Machine Basics_ • Total weight without oil: 4.0 tonnes • Total connected power: 65.0 kW Transcription note: the small footnotes below the plasticising section specify reference materials and test conditions. They are not fully legible in this photo.

Condition: ready for operation (used), Year of construction: 2010, operating hours: 55,000 h, functionality: fully functional, clamping force: 5,000 kN, screw diameter: 90 mm, Clamping force 5000 kN Mould opening force, max. 279 kN Travel force movable platen opening 137,1 kN Travel force movable platen closing 116,8 kN Size of mould platens (h x v) 1370 x 1200 mm Distance between tie bars (h x v) 1000 x 800 mm Mould opening stroke 1170 mm Mould height min 480 mm Max. daylight 1650 mm Hydraulic ejector - stroke 250 mm Ejector force 95 kN Injection unit: Screw diameter 90 mm Ls/D ratio 20 Ibodpfez I Dvyox Ad Njc Injection pressure 1839 bar Stroke volume 2290 ccm Shot weight (PS) 2084 gr. Injection rate 604 ccm/s Screw speed 195 1/min Plasticising rate max. 134,2 g/s Nozzle pressure 129,4 kN Electric and Hydraulic Equipment: Nominal capacity of pump motor 90 kW Installed heating capacity 44 kW Adjustable barrel heating zones 7 Reservoir capacity 1175 ltr. Dimensions and weights: Dimensions of the machine ca. 8,00 x 2,52 x 2,40 m Total machine weight 28800 kg Max. mould weight 7900 kg Accessories: - Anti vibration pads Additional Options: - 1 x air valve - 2 x core pull on fix plate - 2 x core pulls on movable plate - 8 x hotrunner controller - Robot interface according to Euromap 67

Condition: as good as new (ex-display), Year of construction: 2026, functionality: fully functional, clamping force: 5,000 kN, screw diameter: 84 mm, clearance between the columns: 910 mm, displacement volume: 2,050 cm³, injection pressure: 1,620 bar, injection weight: 1,886 g, mold height (min.): 350 mm, ejector force: 110 N, ejector stroke: 250 mm, plate width: 1,260 mm, plate height: 1,270 mm, total length: 7,200 mm, total width: 2,150 mm, total height: 2,230 mm, overall weight: 17,210 kg, type of input current: three-phase, input frequency: 50 Hz, input voltage: 400 V, input current: 183 A, warranty duration: 12 months, Equipment: documentation/manual, Base machine: UN500D1-3330 D=84 Clamping force 500T Tie bar spacing 910x830 Tool installation height 350 to 900 Robot interfaces Euromap 67, Euromap 13 Ibedpfx Aez I T E Ded Nsc Suitable robot available upon request Basic standard equipment: • CE standard • KEBA-3018 control system • Thermal insulation cover for the cylinder • Energy meter, intelligent version • 2 sets of core pull • 1 set of air blow device on the moving platen • 1 set of air blow device on the stationary platen • EUROMAP-67 interface • IT system • EUROMAP-13 core pull interface on the stationary platen • EUROMAP-13 core pull interface on the moving platen • 1 set of 6-way water distributor for the moving platen (11 l/min) • 1 set of 6-way water distributor for the stationary platen (11 l/min)

Year of construction: 2015, condition: used, Vespa plastic grinding machine. Set up is complete with blower , cyclone and bigbagstation Ibsdpfxez Ikqqe Ad Noc Output plastic aprrox 500-600 kg/hour including knives and screen.

Condition: good (used), Year of construction: 2015, 1x Digicolor dryer, as shown in the pictures. Isdpez Inm Aefx Ad Nobc

Condition: like new (used), ENGEL barrier screw with mixing elements, used only once or twice for sampling with polypropylene (PP). All accessories shown in the pictures are included in the purchase price. Ibsdsz H Sfgepfx Ad Noc

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2003, operating hours: 5,000 h, machine/vehicle number: 90201097-0010/2003, screw conveyor diameter: 44 mm, screw conveyor length: 2,420 mm, For sale is a twin-screw extruder from the renowned company Berstorff, manufactured in 2003, for the production and processing of demanding rubber and TPE compounds. The system was operated in a pilot plant of a research institute and was used exclusively for research and development purposes. Unlike systems used in industrial production, the extruder was therefore not used in continuous production. Accordingly, the machine has only a few operating hours. The extruder is particularly suitable for research and development departments, compounders, and companies in the rubber and plastics industry that are looking for a high-performance system for trials, recipe development, material testing, and small-batch production. The detailed technical data and the available screw elements can be found in the attached documentation. The existing equipment allows for flexible configuration of the screw for different compounding tasks. Ibodjz Eqwrjpfx Ad Noc

Condition: ready for operation (used), Year of construction: 2019, operating hours: 17,000 h, clamping force: 500 kN, screw diameter: 18 mm, Electrical injection moulding machine manufactured in 2019. This SUMITOMO SHI DEMAG Intelect 2 50/360-110 features a clamping force of 50 t and a screw diameter of 18 mm. It offers a maximum specific injection pressure of 2800 bar and a maximum dosing volume of 23 cm³. If you are looking to get high-quality injection moulding capabilities, consider the SUMITOMO SHI DEMAG Intelect 2 50/360-110 machine we have for sale. Contact us for further details. Ibsdpfoz Eq Scsx Ad Nec - Max. Specific Injection Pressure: 2800 bar- Max. Dosing Volume: 23 cm³- Mold Height Min-Max: 160 mm - 350 mm- Tie Bar Clearance: 360 mm- Centering Diameter (Fixed / Movable Plate): 125 mm / 125 mm- Maintenance Group: 1- Core Pulls: 2- Working Hours (Drive): 17000 hrs- Ejector Force: 21 kN- Ejector Stroke: 120 mm- Max. Ejector Speed Stage 1: 333 mm/s- Max. Injection Speed: 200 mm/s- Mains Voltage: 400 V +-10% / 50 Hz, 3 Ph + N + PE- Hot Runner Control: 3 zones integrated, 2.75 kW- Integrated Hydraulic Servo Power Unit: Max. 25 l/min

Condition: used, functionality: fully functional, nominal power: 150 kW (203.94 HP), Deguma drop mill, older model - 1800 mm wide - Hard metal and gearbox mounted on the machine bed - Water-cooled via lances - Pneumatic clamping system - Fencing with emergency stop control - Drive motor 150 kW - Central lubrication system - Starter Ibedez Erxqspfx Ad Noc - Control cabinet - Selling a complete mixing line; attractive package price possible.

Condition: used, Year of construction: 2005, operating hours: 61,407 h, clamping force: 1,600 kN, screw diameter: 50 mm, clearance between the columns: 470 mm, For sale is an injection molding machine from Arburg, model 470 C 1600-800. The pump and one circuit board have been removed from the machine; therefore, the machine is being sold as defective. Otherwise, it is in very good condition. Technical specifications: Pump operating hours: 61,400 Clamping force: 1600 kN Distance between tie bars: 470 x 470 Ejection stroke: 225 mm Screw diameter: 50 mm Displacement: 398 cm³ Dimensions: 4335 x 1635 x 1950 mm Weight: 6950 kg The machine is offered without any peripherals. Upon request, transport and loading can be arranged throughout Europe for an additional fee. Prices are plus VAT. Ijdpfxjz Etu Ho Ad Nobc Inspection is possible by appointment. Contact us; our team will be happy to assist you. Trade-in or exchange is possible! Machine buying and selling WE BUY / SELL PRODUCTION & METALWORKING MACHINES, AND MORE. Do you need a high-quality but affordable metalworking machine for your production? Or do you want to sell yours? For further information or contact options, please visit our website.

Condition: new, Year of construction: 2026, overall weight: 1,900 kg, Big Bag unloading station complete with electric lifting hoist, discharge hopper, structural steel support frame, service platform with access stairs, and perimeter safety guards. Suitable for handling and unloading various bulk materials, including plastic granules, plastic flakes, flour, powders, and similar products. Iedpfx Aoz Hlgkod Njbc

Condition: excellent (used), Year of construction: 2014, Number of axis: 4 Reach: 3000 mm Ijdpfx Adjz E Rkfj Nebc Payload: 10 kg

Condition: used, Universal temperature control unit REGLOPLAS Type 90M/10/SG73/D K/RT50 Temperature control unit with electric heating and connections for external cooling Circulating process temperature control for industrial use in plastics processing, particularly for temperature control of injection molds and other process tools. Serial No.: 102010730001 Year of manufacture: 2010 Temperature max. 90°C (for water) Heat transfer medium: Water Temperature range: +20°C to 90°C Operating overpressure: max. 6 bar Pump capacity: 60 l/min Tank volume: 2.8 liters (internal filling volume) Heating capacity: 10 kW Cooling capacity of heat exchanger: up to 160 kW (depending on the external cooler) Motor power of the pump: 1 kW Continuous sound pressure level Ibjdsz Ek Spjpfx Ad Nsc