HIGH SPEED VERTICAL BORER

Webster & Bennett EV 36”

Condition: excellent (used), Year of construction: 2018, operating hours: 2,000 h, functionality: fully functional, turning height: 3,000 mm, workpiece weight (max.): 30,000 kg, turning diameter: 3,500 mm, power: 100 kW (135.96 HP), TECHNICAL CHARACTERISTICS 1. Max. machining diameter mm 3.500 2. Min. machining diameter mm 0 3. Max. height of the part mm 3.000 4. Max. load on the table to 30 5. Table diameter mm 3.000 6. Table speed range rpm 2 ÷ 130 7. Main AC motor - turning kW 100 8. The maximum torque of the faceplate in turning mode Nm 105.000 Rodpfx Abstpnlwsbet 9. Ram vertical stroke (Z axe) mm 1.750 10. Turning ram cross section mm x mm 300x300 11. Horizontal stroke –X axe mm 2.000 12. Feed range (X and Z axe) mm/min 1 ÷ 6000 13. Rapid traverse (X and Z axe) mm/min 8.000 14. Feed motor torque (X and Z axe) Nm 22 18. Vertical stroke of the cross rail mm 2.700 CNC Equipment 1. Equipment type Fanuc Overall Dimensions 1. Floor space m 8.5 x 6 2. Max. height of the machine m 8.2 3. Max. height over floor level m 7.4 3. Machine weight to 89 Tool Magazine 1. Number of tool magazines - 1 2. Number of tools/magazine - 16 3. Feed motor torque with encoder Nm 12 4. Tool change time sec. 25 5. Maximum weight of the tool holder - for turning daN 100 6. Maximum length of the tool holder - for turning mm 600

Condition: used, Year of construction: 1957, ram hammer weight 200 kg ram hammer stroke 525 mm no. of strokes 150 /min impact energy 420 kJ distance lower die block / ram gudeway 435 mm Throat 425 mm steel forging - rectangular up to 110 mm steel forging - diameter up to 125 mm power requirement 22,0 kW weight of hammer 3,9 t weight of anvil 3,0 t weight 6,9 t dimensions (WxDxH) 1,1 x 2,3 x 2,4 m Forging hammer Redpevzxpbefx Abbet as is where is, WITHOUT putting into operation

Condition: refurbished (used), Year of construction: 2021, functionality: fully functional, center height: 150 mm, workpiece weight (max.): 130 kg, grinding length: 1,500 mm, grinding wheel diameter: 500 mm, total width: 2,155 mm, total length: 5,465 mm, total height: 1,700 mm, grinding diameter: 300 mm, grinding wheel width: 63 mm, The cylindrical grinding machine was fully overhauled in 2021 and has hardly been used since. The condition of the machine is practically like new. Equipment as shown in the photos. The machine is connected to power and can be inspected at any time by prior arrangement. Technical specifications: Rodpfx Ajx A Dfyebbst Grinding diameter: 300 mm Grinding length: 1500 mm

Condition: used, Year of construction: 1987, pressure / t stroke / mm table-size / mm weight of the machine ca. 65000 kg Make: Shepherd Type: SVRM 4-roller bending machine: Year of construction: 1986 Working width: 3000cm Smallest pipe diameter with 600 mm roller: Ø 720 mm Smallest tube diameter with 360 mm roller: Ø 460 mm Sheet thickness up to (depending on the material): 50 mm Material SA- 738 B Working width: 2500 mm Material SA- 738 B Material thickness: 35 mm conical bending: Except for the top roller, all rollers can be moved in an inclined position for conical bending. The roller positions can be read on display instruments. For semi-automatic or fully automatic operation of the machine, the bearing jewels of the rollers are equipped with scale bars and slide cams for limit switch actuation. This allows the rollers to return to the same set position over and over again, giving a very high level of uniformity in the shot wefts being bent. Redpjuddcajfx Abbjt

Year of construction: 1971, condition: used, Technical details: max. wheel diameter: 300 mm max. module: 5 module min. : 0,5 max. workpiece weight: 60 kg weight of the machine ca.: 4,0 t dimensions of machine: 1800x1850x2500 mm dimensions electric cabinet: Nr. 1: 1930x400x1920 mm dimensions electric cabinet: Nr. 2: 800x230x1950 mm dimensions:: Abluftanlage: 1400x700x560 mm dimension cooling device LxWxH: 1,2 x 1,0 x 0,45 m Electronically controlled tooth flank grinding machine up to module 5 and a Ø of 240 - 300 mm feed speed per workpiece revolution infinitely variable 0.4 - 3.2 mm max./min. Number of teeth: 130 / 12 max./min. Pressure angle: 30° / 14°30` max./min. Spiral pitch with 24 teeth: 6000 / 200 mm max. tooth helix angle, both sides: 45° Speed of the grinding worm: 1900 rpm without dressing device Rsdpfx Absvc Apbsbet Equipment: approx. 77x change transmission wheels, pipe extensions and various tools Two of these machines are for sale. Both machines are supplied via two common control cabinets and an exhaust air system. *

Condition: reconditioned (used), functionality: fully functional, turning diameter over cross slide: 690 mm, spindle bore: 150 mm, turning diameter: 1,040 mm, turning diameter over top slide: 690 mm, center height: 500 mm, center width: 2,000 mm, spindle speed (max.): 5,000 rpm, travel distance X-axis: 160 mm, travel distance Z-axis: 380 mm, bar passage: 55 mm, Center height: 500 mm Distance between centers: 2.000 mm Maximum turning diameter: Over cross slide: 690 mm Over bed: 1.040 mm Over gap: 1.070 mm Bed width (hardened guides): 670 mm Gap length: 480 mm Gap length in front of the faceplate: 320 mm CARRIAGE Length of bed guideways: 1.020 mm Cross slide travel: 640 mm Compound slide travel: 360 mm SPINDLE Spindle nose: ASA 15’’ Spindle bore diameter: 150 mm Front bearing size (NN): 200 / 310 / 82 mm Rear bearing size (NNU): 190 / 260 / 69 mm Internal Morse taper reduction sleeve: No. 6 Number of spindle speeds: 24 Speed range: 4 ÷ 800 rpm THREADING Total number of threads: 398 Metric threads: 0.5 ÷ 224 mm Module threads: mod. 0.25 ÷ 11 Whitworth threads: 56 ÷ 1/8 TPI Diametral pitch threads: 112 ÷ 1/4 DP FEEDS Number of feeds: 108 Longitudinal, cross and compound feeds: 0.05 ÷ 22.4 mm/rev RAPID TRAVERSES Longitudinal, cross and compound: 2.500 mm/min Longitudinal return: 5.000 mm/min TAILSTOCK Quill diameter: 130 mm Quill Morse taper: No. 6 Quill travel: 420 mm Rodpfeyhhuwsx Abbet STEADY RESTS Bed steady rest capacity: 140 ÷ 500 mm Carriage steady rest capacity: 40 ÷ 350 mm PERMISSIBLE LOAD Cantilever load: approx. 1.500 kg Between centers, without steady rest: approx. 5.000 kg Between centers, with steady rest: approx. 6.000 kg Machine weight: approx. 7.800 kg

Condition: good (used), Year of construction: 2012, functionality: fully functional, machine/vehicle number: 42L09420, Hankook Protec 9NC x 5000 CNC Lathe with Fanuc 32i Control and large spindle bore. MACHINE CONSTRUCTION & FEATURES  Heavy One Piece Cast Iron Bed Construction  Heavy Duty Hardened & Ground Solid Slideways  2 Step manual Gear Change  Heavy Duty Tailstock MACHINE CAPACITIES Swing Over Bed Ø 950 mm Swing Over Carriage Ø 630 mm Chuck Size Dia. Ø 32” Distance Between Centres 5000 mm Load Capacity Between Centres 5000 Kgs SPINDLE Speed 2 -630 Rpm Spindle Bore Ø 254 mm Spindle Nose A2-15” Speed Range Manual 2 Step Centre taper MT #6 Carriage Toolpost Automatic V8 Tool Size 32 x 32 mm X Axis Travel 535 mm Z Axis Travel 4845 mm X Axis Rapid 4 M/min Z Axis Rapid 6 M/min TAILSTOCK Rodpfxewcq Tmo Abbjt Quill Diameter Ø 180mm Spindle Taper MT #6 Max Quill Travel 250 mm BED Width 630 mm Length 6715 mm MOTORS Spindle 30/37 Kw Feed X 1.8 Kw Z 4.2 Kw POWER SUPPLY Electrical Supply 415V, 3Ph, 50Hz DIMENSIONS & WEIGHT Length 7470 mm Width 2205 mm Height 1890 mm Weight 10280 Kgs STANDARD MACHINE FEATURES • Fanuc 32i-A CNC Controller • Centre MT #6 • 4 Jaw Independent chuck • Automatic Spindle Shifting • Built in Live Tailstock Spindle • Coolant System • 2 Speed Tailstock Spindle • Work Light • Main Drive Motor & Elect equipment • Centre Sleeve • Chuck Cover Full Rear Guard 5000 between Centres 4-Jaw Independent Chuck & Flange Φ32" (Bore Ø254mm) 4-Jaw Independent Chuck & Flange Φ32" (Bore Ø254mm) Steady Rest(Roller Jaw) Φ250mm - Φ450mm Steady Rest (Roller Jaw) Φ450mm - Φ650mm Live Centre MT #6 Automatic Index Turret Electric V8 in lieu of manual H-4 3 Off OD Tool Holders 3 Off Boring Tool Holders Φ63mm 2 Off Facing Tool Holders Boring Bar Device Ø 150mm (Bar Excluded) Chip Conveyor 5000 Mm Transformer CE Specification Spindle Motor Upgrade 30/37 Kw Fanuc Option A (as detailed below) 1st Spindle Orientation Dynamic Graphic Display Continuous Threading Custom Macro B Extended Part Program Edit Tape Memory 320M Inch/Metric Conversion Manual Guide i Playback Programmable Data Input Run Hours & Parts Counter Tool Offsets 32 Pairs Variable Lead Threading Graphic Function Spindle Positioning Program Restart External Data Input

Condition: used, Year of construction: 1977, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0,001-0,030 mm/Ø 0-0,95 mm/Ø ±8 ° longitudinal feed of the table 1300 mm table speeds 0,02-6 m/min 130 kg Rjdjynmpgopfx Abbst 130 inkl. Spannugkg kg 70 mm total power requirement 6,5 kW weight of the machine ca. 2,5 t dimensions of the machine ca. 4,2 x 2,0 m Neu geliefert an Universität. 2018 übernommen. Dann komplett bei BEMA gewartet und an an Einmannbetrieb geliefert. Nun wird die Maschine nochmal gewartet und Tischgeometrie neu hergestellt. 2-Achsen-Digitalanzeige Fagor nachgerüstet. -Reitstock mit Feinverstellung -Innenschleifeinrichtung -Kühlmittelanlage Zubehör auf Anfrage

Condition: used, Year of construction: 1965, There are two WMW SU 315x3000 available, connected load machine 1/ 2: 12.6/ 12kW, weight machine 1/ 2: 8.2/ 9t, machines need overhauling. Rjdpfoxg Ihgjx Abbet

Condition: used, Year of construction: 2006, functionality: fully functional, center height in crank: 1,100 mm, workpiece weight (max.): 180,000 kg, grinding length: 11,000 mm, grinding wheel diameter: 1,066 mm, total length: 11,700 mm, quill travel distance: 11,700 mm, workpiece weight between centers: 180,000 g, distance between centers: 11,700 mm, POMINI CNC Roll Grinder Model HD-425-2-7L Siemens 840D, 12 Axes. Built in 2006. Two flatbed system grinding and workpiece ways are separate. Machine accuracy. Straightness 0.001-0.002 mm/m. Roundness 0.001-0.002 mm. Eccentricity 0.002 mm. Profile for crown height up to 0.1 mm ±0.002 mm/m. Surface finishing without chatter marks and no feed marks after finishing grinding stage. On an independent bed: Auto Caliper Diameter 870 - 2,250 mm. Eddy current crack and bruise detector probe. Ultrasound depth probe up to 180 mm. High Pressure wheel cleaner. Redpswdmy Sofx Abbot Wheel dynamic balancing electromagnetic automatically or manually. Wheel dressing device with diamond. 2 Hydrostatic Steadies. 2 Hydrodynamic Steadies. 4 Soft landing for roles. Wheel quick change device incl motor. Jib crane. Vibration Measurement, recording on: Headstock base Neckrests Foot stock Wheel head Wheel head back Carriage Lateral side. Working Capacity. Grinding length 11,000 mm Max diameter with 1,066 mm Grinding wheel 2,200 mm Min diameter with 1.066 mm Grinding wheel 800 mm Center distance 11,700 mm Max Roll weight 80 Tons Max Roll weight with Steadies 180 Tons Min distance between wheel center and roll axis 845 mm Max distance between wheel center and roll axis 1,635 mm Carriage Axis Z, Hydrostatic Feeds, Infinitely variable 0-6,000 mm/min Oil film thickness 0.020 mm Distance between carriage ways 1,500 mm Ways width 160 mm Total length of the carriage on ways 3,385 mm Wheelhead on Carriage Axis X, Wheel Probe Axis A, Inspector Axis A1, Wheelhead cross travel Ballscrew, Axis X 940 mm Resolution axis X 0.0001 mm Wheel Spindle length 1,695 mm Spindle bearing, hydrostatic, diameter 254 mm Resolution Infeed micrometer handwheel, Axes X 0.00001 mm / division Continuous wheel infeed, U axis on radius 0 - 0.35 mm/min Rapid wheel indeed, axes X 0-830 mm/min Wheel motor, AC 130 kW Wheel Speed 400-1,100-1,600 rpm Wheel Cutting Speed infinitely variable Surface speed wheel diameter 1,066 mm 45 m/sec Surface speed wheel diameter 670 mm 45 m/sec Wheel hole, diameter 508 mm Wheel thickness 76 - 152 mm Wheel diameter 670 - 1,066 mm Crowning, Axis U. Max crown on the diameter 10 mm Max concavity on the diameter 10 etc Head stock Workpiece rotating speed 5 - 50 rpm Headstock motor 200 kW Max transmissible torque 76.5 kNm Faceplate control system V Belts Max Center diameter, metric type 160 mm Stroke of Quill 150 mm Length of headstock 3,110 mm Tail stock Quill diameter 260 mm Stroke of quill 750 mm Maximum center diameter, metric type 160 mm Taper Metric 5% on the diameter Tailstock length 1,300 mm Stroke of tailstock 8,000 mm Caliper, Arm Axis C, Carriage Axis V, Rotation Axis B. Max measurable diameter 2,250 mm My measurable diameter 870 mm Machine Dimensions. Machine weight 130 tons Length 19.5 m. Width 5.5 m. Height 3.2 m. Foundation depth 3.8 m.