Gear hobbing machine Sinumerik One

Liebherr LC 282 - Siemens

Condition: excellent (used), Year of construction: 2006, x-travel 750 mm y-travel 210 mm z-travel 1150 + 100 mm control Fanuc MSX-701III Maximum turning diameter 660 mm Max. turning length 1498 mm Diameter over cross slide max. 400 mm Knedpjy Spuuofx Agrjb number of spindle speeds 3000 U/min tool piece magazine with 40 Plätzen turret 10 Fach total power requirement 90 kVA weight of the machine ca. 26,6 t dimensions of the machine ca. 5301 x 2997 x 2788 mm

Condition: good (used), Year of construction: 2000, gear diameter: 449 mm, Equipped with: Fanuc 150MB CNC Control Dry Cutting Cutter Shroud Chip Evacuation System Auto Doors Hydraulic System Lubrication System Work light Stack Light Specifications: Largest Speed Ratio: 10:01 Work Area (Continuous): Largest Depth of Teeth: 15.24 mm Largest Width of Tooth Face: 50.8 mm Work Area Axis: Horizontal Movement X Axis: -114 - 178 mm Vertical Movement Y Axis: -178 - 190 mm Movement of the Carriage Baseplate Z-Axis: -10.16 - 500 mm Workpiece Headstock Swiveling Range B-Axis: -3 - 90 Degree Maximum Distance Machine Center to Spindle Side: 165 mm Kederuakgepfx Agrsnb Number of Teeth: 5-200 Inclusive Max. Gear Pitch Dia. of Typical 35 Deg. Spiral Angle Gear Using Max. Cutter Dia. 12" Cutter at the Following Ratios: Face Milling 1 x 1 - 13.5" - 342.9mm 2 x 1 - 16.0" - 406.4mm 5 x 1 - 17.7" - 450.0mm Face Hobbing (210mm Dia. Cutter) 1 x 1 - 10.560" - 268.22mm 2 x 1 - 10.286" - 275.00mm 5 x 1 - 11.810" - 300.00mm Milling Head Diameter: Helixact: 100,125,169,200,250,320mm Continuous Gumption Procedure, Teichloroethylene: 102 - 210 mm Workpiece Spindle: Drilling of Large Diameters: 5 3/64" Cone Upward Gradient on 304.8 mm (1 Foot): 21/32" Deep One of the Cone: 5.29" Diameter of the Whole Spindle Perforating: 3.35" Speeds: B-Axle Workpiece Headstock Drag Axis: 30 Degrees A-Axle Workpiece Spindle Number of Revolutions: 0 83 min-1 X-Axis Horizontal: 80 mm/sec Y-Axis Vertically: 80 mm/sec Z-Axis Carriage Baseplate: 80 mm/sec Space Requirement L x W x H (Approximate): 4.75 x 3.40 x 2.54m / 188" x 134" x 100" Machine Weight (Approximate): 10980 kg / 24,156#

Condition: good (used), Year of construction: 2009, max. wheel diameter 1200 mm gear width 260 mm max. module 16 min. module 0,5 stroke 270 mm distance between table/spindle 920 mm taper of shaper cutter SK control Bosch MTX table diameter 900 mm Knodpfx Aowzmpzjgrob min. workpiece diameter-at internal hobbing 1200 mm strokes - infinitely variable 50-1000 Hub/min spindle diameter 125 mm table hole 320 mm Distance of shafts Min/Max 0-820 power capacity Stosskopf 30 KW total power requirement 72 KVA weight of the machine ca. 24 t dimensions of the machine ca. 6,5x2,9x4 m Liebherr LH 90 control, 9 axis CNC, top condition.

Condition: used, Year of construction: 1998, Technical details: max. module: 7 weight of the machine ca.: 5 t worm grinding diameter: 280-350 mm width of grinding worm: 84-104 mm min. number of teeth: 6 Kjdpfx Agezgw I Nsrsnb max. number of teeth: 600 max. top circle diameter: 360 mm max. workpiece weight: 60 kg with Turbo Separator, loading unit, latest-generation balancing and dressing unit and various accessories *

Condition: used, Year of construction: 2004, functionality: fully functional, CNC gear hobbing machine Control: Siemens 840 D Power Line Technical data: Max. workpiece diameter: 150 mm Table diameter: 145 mm Max. table speed: 800 rpm Distance between centers: 10 – 200 mm Max. axial travel: 250 mm Swivel angle of milling head: +/- 45° Max. tailstock travel: 300 mm Max. rapid traverse rate: 17,000 mm/min Drive power of milling head: 19 kW Max. module: 3 mm Max. speed of milling spindle / tool speed: 4,500 rpm Max. diameter of hobbing cutter: 80 mm Max. length of hobbing cutter: 200 mm Dimensions approx.: 5.5 x 3.7 x 3.1 m Weight approx.: 9,500 kg Equipment: Chip conveyor Oil mist extraction / oil extraction Oil cooler Steady rest with lowering device and vertical adjustment Kodpfozkwvnox Agrjnb Rotary ring loader with two workpiece grippers Loading belt system for automatic feeding 5 milling arbors / hobbing cutter holders: 1 x Ø 22 mm 2 x Ø 27 mm 1 x Ø 32 mm 1 x Ø 40 mm Other: Video recordings via WhatsApp

Condition: excellent (used), Year of construction: 2019, machine/vehicle number: 32006, input voltage: 480 V, The Sprinter for Gears with Short Face Widths up to 100 mm The 100S Gear Shaping Machine is ideally suited for small face widths, for shaping spur and helical gears, internal and external, and for crowned and tapered gears. With only 6 m2 the 100S is one of the most compact machines of its class. Equipped with: Siemens Sinumerik 840D SL Control Hydraulic System 180 Degree Load System HSK-63 Spindle Auto Stroke Adjustment Chip Conveyor Chip Basket Knodpfsrtrvyex Agrsb Flexlink Automation Festo Pneumatics Rittal Panel Conditioners Chiller 480/3/60, 35 KvA Motor & Controls Specifications: Workpiece With External Gear: -Largest Module (Steel W/Approximate 600 N/mm2): 3 mm -Maximum Width: 26 mm -Maximum Diameter: 100 mm Workpiece With Internal Gear: -Largest Module (Steel With Approximate 600 N/mm2): 3 mm -Maximum Width: 26 mm -Maximum Swing Diameter: 150 mm -Maximum Internal Diameter: 100 mm Tool: -Locating Cone In The Cutter Spindle: HSK-D63 -Diameter Shaping Spindle: 85 mm -Maximum Stroke Length: 30 mm Machine Travel Distances: -Radial (X-Axis): 180 mm -Column Tilting (B-Axis): -1 - +11 Degrees Machine Workpiece Table: -External Diameter: 220 mm -Clamping Diameter: 160 mm -Bore: 63 mm Speeds: -Feed Rate X-Axis: 12,000 mm/min -Workpiece Table (C-Axis): 0-400 min-1 -Cutter (C2-Axis): 0-300 min-1 -Spindle Stroke (A-Axis): 500-3,000 min-1 Electrical Equipment: -Operating Voltage: 480V -Supply Voltage: 115V -Control Voltage: 24V -Frequency: 60 Hz -Connected Load of Machine: 35 kVA -Cable Cross-Sectional Area: 35 mm2 -Protection: 80 A Machine Overall Dimensions (L x W x H): 3,380 x 3,950 x 3,015 mm Weight of Machine: 7,800 kg

Condition: used, Year of construction: 2006, Technical details: max. wheel diameter: 300 mm Knsdpfx Agsyz Sd Rereb max. module: 7 weight of the machine ca.: 15 t table turning speeds: 100 U/min table diameter: 180 mm hob turning speeds: 750 U/min max. hob diameter: 300 cutter length max.: 230 mm Liebherr LC300 with loading automation Machine including counter holder The machine used to work with emulsion *

Condition: used, Year of construction: 2001, Technical details: max. wheel diameter: 200 mm gear width: 50 mm max. module: 6 table diameter: 168,14 mm boring diameter: 65,532 mm Kjdpfx Agexz Avberjnb weight of the machine ca.: 11 t table turning speeds: 0-1.000 U/min length of stroke min./max.: 0-70 mm no. of strokes: 180-1.800 Stück This machine can be used to make tandler gears. However, for helical gearing, a helical guide is also required. *

Year of construction: 2007, condition: good (used), machine/vehicle number: 1380-1207, >with Siemens Sinumerik Panel Control Knsdpfxjm Nb Rio Agrob >with chip conveyor >control panel >electric cabinet >capacity through spindle 60 mm >max. piece length 340 mm

Condition: ready for operation (used), Year of construction: 2019, travel distance X-axis: 540 mm, travel distance Y-axis: 500 mm, travel distance Z-axis: 700 mm, controller manufacturer: SIEMENS, controller model: 840D, number of axes: 5, This 5-axis DMG Mori Seiki LaserTec 50 was manufactured in 2019. It features a Celos with Siemens 840D sl Operate control, integrated ytterbium cw fiber laser, and a compact design with a 4 m² footprint. Ideal for machining diamond tools with dimensions up to Ø 355 mm and 420 mm in length. If you are looking to get high-quality laser machining capabilities, consider the DMG Mori Seiki LaserTec 50 machine we have for sale. Contact us for more information. • Control: CELOS with Siemens 840D sl Operate; 21.5" ERGOline Control with multi-touch screen • Processes: Laser fine cutting, laser drilling, laser welding • Work capacity: Machining diamond tools up to Ø 355 mm and 420 mm in length • Axes/table: NC swivel rotary table; 5-axis transformation; high-dynamic torque motors in B and C axes • Drives: Linear drives in X/Y with acceleration > 1 g • Laser source: Integrated ytterbium CW fiber laser; 450 W QCW ytterbium fiber laser with 4,500 W pulse peak power and 450 W average power • Processing head: 80 mm focal length; collision switch • Vision: Camera through beam path for fiber laser • Construction: Solid mineral cast base • Footprint: Approx. 4 m² • Condition/usage: ~100 working hours (as new) • Notes: CNC precision laser machine with high-speed processing; highly dynamic and precise Additional equipment • Fanuc robot automation Kedpsyfv Tvefx Agrjnb • Keller automatic extraction system • Basement exhaust extraction system