Gear Hobbing Machine - Vertical

EMAG WF180

Condition: good (used), Year of construction: 2000, gear diameter: 449 mm, Equipped with: Fanuc 150MB CNC Control Dry Cutting Cutter Shroud Chip Evacuation System Auto Doors Hydraulic System Lubrication System Work light Stack Light Specifications: Largest Speed Ratio: 10:01 Work Area (Continuous): Largest Depth of Teeth: 15.24 mm Largest Width of Tooth Face: 50.8 mm Work Area Axis: Horizontal Movement X Axis: -114 - 178 mm Vertical Movement Y Axis: -178 - 190 mm Movement of the Carriage Baseplate Z-Axis: -10.16 - 500 mm Workpiece Headstock Swiveling Range B-Axis: -3 - 90 Degree Maximum Distance Machine Center to Spindle Side: 165 mm Number of Teeth: 5-200 Inclusive Max. Gear Pitch Dia. of Typical 35 Deg. Spiral Angle Gear Using Max. Cutter Dia. 12" Cutter at the Following Ratios: Face Milling 1 x 1 - 13.5" - 342.9mm 2 x 1 - 16.0" - 406.4mm 5 x 1 - 17.7" - 450.0mm Face Hobbing (210mm Dia. Cutter) 1 x 1 - 10.560" - 268.22mm 2 x 1 - 10.286" - 275.00mm 5 x 1 - 11.810" - 300.00mm Milling Head Diameter: Helixact: 100,125,169,200,250,320mm Continuous Gumption Procedure, Teichloroethylene: 102 - 210 mm Workpiece Spindle: Drilling of Large Diameters: 5 3/64" Cone Upward Gradient on 304.8 mm (1 Foot): 21/32" Deep One of the Cone: 5.29" Bodpsruakgefx Adqedf Diameter of the Whole Spindle Perforating: 3.35" Speeds: B-Axle Workpiece Headstock Drag Axis: 30 Degrees A-Axle Workpiece Spindle Number of Revolutions: 0 83 min-1 X-Axis Horizontal: 80 mm/sec Y-Axis Vertically: 80 mm/sec Z-Axis Carriage Baseplate: 80 mm/sec Space Requirement L x W x H (Approximate): 4.75 x 3.40 x 2.54m / 188" x 134" x 100" Machine Weight (Approximate): 10980 kg / 24,156#

Year of construction: 2007, condition: good (used), machine/vehicle number: 1380-1207, >with Siemens Sinumerik Panel Control >with chip conveyor >control panel >electric cabinet Bdsdpfxjm Nb Ris Adqef >capacity through spindle 60 mm >max. piece length 340 mm

Condition: used, Year of construction: 1981, National 2-3 Hot Former Bdjdpfewl Iw Uox Adqsf induction heater, feeder, straightener

Condition: used, Year of construction: 1975, max. bore diameter to be ground 6 bis 100 mm stroke - stepless adjustable 550 mm grinding depth ca. 250 mm workpiece weight 150 kg total power requirement 15 kW weight of the machine ca. 4.300 kg Bodpeucgwkefx Adqjdf dimensions of the machine ca. 2,7 x2,4 x 2,2 m

Year of construction: 1991, condition: good (used), Ref. -No.: 10656 Manufacturer: PFAUTER Type: PE 150 Year of construction: 1991 Type of control: CNC Control: Sinumerik 840 Storage location: Halberstadt Country of origin: Germany Turning Speeds: 150 - 600 RPM Tool Taper: SK 40 Machine length: 4700 mm Machine width: 3600 mm Machine Height: 2800 mm Weight: 8 t Workpiece Diameter: 150 mm Maximum tooth width.: 150 - 200 mm Table diameter: 160 mm Table drilling: 63 mm Max. cutter diameter: 130 mm Max. cutter length: 220 mm swivel angle: +/- 45° Further information: - The machine has been completely converted to Siemens 840D, including the motors and control cabinet. - The milling head was completely overhauled by Pfauter in 2013. - The low-voltage system and magazine conveyor are included. - It is equipped with a deburring station. Bdodjzkpx Ujpfx Adqef The machine can be viewed while powered on by prior arrangement.