NC multipurpose milling machine

AIRCRAFT Optimill MF 4-B

Year of construction: 2002, condition: reconditioned (used), Beam cutting, drilling and marking line DISC SAW Brand: KALTENBACH Model: HDM 1431 / T13 / SP-CNC Year 2002 Serial number: 122.400 Weight without accessories: 10,980kh - Disc saw with downward cut. - Geared saw unit, drive system and saw blade on wear-resistant swivel bearing. - Heavy saw gear with pinions in oil bath, with inclined teeth, hardened and sharp. - Hydraulic advancement of the saw blade, adjustable according to the table, very fast recoil. - Hydraulic horizontal clamping device. Rear clamping jaw with long-stroke clamping cylinder and automatic recoil limitation. - Vertical clamping block with self-adjusting push plate. - Oblique cutting device to adjust the angle from 45° to the left to 35° to the right. - Material sensor to automatically switch from rapid advance to work advance. - Hydraulically elevating feed roller for optimum material transport on the saw table. - Economical lubrication by means of a micro-dosing installation, especially suitable for sawing profiles. - Chip collector installed on the machine bench. Specs: - Cutting disc housing: 100x4x30x250mm - Cutting disc diameter: 1,430mm - Cutting width: 9.5mm - Cutting speed: 10 to 20m/min. - Saw advance speed: 0-400mm/min. - Fast reverse speed: 2000mm/min. - Total power: 25KW - Working height: 640mm Cutting capacities: 90º cut - Angle steel: 250mm - Steel in U: 400mm - Double T-beam: 600mm - Wide flanged beam: 1008x302mm - Special wing beams: 1000x450mm Cut to degrees: IPBv beam - 75º: 1008x302mm Podpfx Ashzbipof Seha - 60º: 910x302mm - 45º: 716x304mm - 40º: 716x304mm - 35º: 478X307mm IPBs beam - 75º: 1008x402mm - 45º: 524x357mm IPE beam - 45º: 600x220mm DRILLING UNIT Brand: Kaltenbach Model: KDX1215 Serial number: 122.401 Work capabilities: - Angular steel (minimum - maximum): 80x65x10mm - 250x250x28mm - Steel in U (minimum - maximum): 80x45mm - 400x110mm - Double T beam (minimum - maximum): 80x46mm - 600x220mm - Wide flanged beam (minimum - maximum): 100x100mm - 1,008x302mm - Extra wide wings beam: 1,200x500mm Drilling units: 3 - Vertical (Y axis) 1 pc. - Horizontal (Z and W axes) 2ud. Drilling diameters: 8 - 40mm RPM: 150 - 1100 Fast forward - Fast reverse: 3,850mm/min. - 8,000mm/min. Drilling spindle feed rate: 0-500mm/min. Fast spindle positioning tool: 15,000mm/min. Automatic tool changer: 5 u. in each drilling unit. 3x5 u. = 15 total Total power: 45KW MARKING UNIT FEEDING: 26 METERS OF ENTRY WITH BEAM FEEDER + 6 SIDE ARMS FOR BEAM ENTRY IN PARALLEL TO THE ROLLER TRACKS 30 METERS OF ROLLER TRACKS WITH OUTPUT + 6 SIDE ARMS 4 SIDE ARM FOR SMALL PIECES THE GREAT MAJORITY OF ROLLERS ARE MOTORIZED It occupies approximately 60 linear meters between input and output power. *Request machine installation plans.

Condition: new, Optimum OPTImill MZ 2S tool milling machine With digital 3-axis position display DP 700 from NEWALL. With inverter drive of the feed axes controllable from the control panel. Versatile application range Excellent damping characteristics and stability of the machine frame All guideways hardened and precision ground and adjustable by means of taper bars Automatic feed in X, Y and Z axes, infinitely adjustable via an electronic joystick on the control panel Electric feed limit stop Ball screw in all axes Central and clearly arranged control panel with integrated digital position and speed display Massive cross table, large dimensioned and precisely surface machined with 5 T-slots Coolant device Large dimensioned handwheels with scale Machine lamp Quiet running Manual central lubrication TECHNICAL DATA Dimensions and weights Length (product) approx. 1239mm width/depth (product) approx. 1168mm Height (product) approx. 1900mm weight (net) approx. 1400kg Drilling-milling head milling head swivel range ± 90 Drilling-milling capacity cutter head size max. 100mm drilling capacity steel (S235JR) 30mm Continuous drilling capacity steel (S235JR) 26mm End mill size max. 25mm Electrical data Power drive motor 2,2kW Supply voltage 400V Mains frequency 50Hz Horizontal milling table Horizontal milling table length 750mm Horizontal milling table width 320mm distance vertical spindle - horizontal milling table min. 75mm distance vertical spindle - horizontal milling table max. 410mm Horizontal milling table T-slots size 14mm Horizontal milling table T-slots number 5 Horizontal milling table T-slots distance 63mm Distance horizontal spindle - horizontal milling table min. 70mm Distance horizontal spindle - horizontal milling table max. 400mm Horizontal milling table load max. 285kg Milling table vertical Vertical milling table length 830mm Vertical milling table width 250mm Vertical milling table T-slots size 14mm Vertical milling table T-slots number 2 Vertical milling table T-slots distance 63mm Coolant system Coolant pump(s) Drive power 95W Travel Travel X-axis manual 400mm Travel Y-axis manual 200mm travel Z-axis manual 335mm Travel X-axis automatic approx. 310mm Travel Y-axis automaticapprox. 160mm Travel Z-axis automatic 295mm Vertical spindle Vertical spindle throat 100mm Vertical spindle Spindle mounting ISO 40 DIN 2080 Vertical spindle speed range 50 - 1890min¯¹ Vertical spindle number of speed ranges 12steps Vertical spindle tightening rod M 16 Vertical spindle quill stroke 120mm Vertical spindle load max. 1100Nm Feed speed Feed speed X-axis 10 - 600mm/min feed speed Y-axis 10 - 600mm/min feed speed Z-axis 10 - 600mm/min Electrical connection Total connected load 4kW Motor(s) rapid traverse X-axis power drive motor 0,375kW rapid traverse Y-axis power drive motor 0,375kW Phedpfofnh Sgex Af Soa Rapid traverse Z-axis power drive motor 0.375kW SCOPE OF SUPPLY: Adapter ISO 40/MK3 adapter MK1 and MK 2 Milling spindle horizontal milling Ø 27 mm Operating tool

Condition: new, machine/vehicle number: 280270 0001, ADVANTAGES: compact table machine simple operability 3-axis stepper motor control with path operation Ball screws 2-phase stepper motors CNC control software included ICP series - with stepper motor drive and path control GENERAL CNC machines of the ICP series are further developments of the proven CPM series. The introduction of a sliding door means that the machines can now be operated from a seated position, which results in shorter cycle times for hood opening, among other things. The chassis is completely bolted together instead of welded as in the predecessors. This results in greater precision when setting up the machine, as well as improved serviceability. Furthermore, the resonance and vibration behavior has been optimized, resulting in lower noise levels. X = 400mm Pjdpfx Afolkbpzs Ssha Y = 300 mm Z = 140 mm Diffuser = 200 mm -in use for over 40 years!!! -over 20,000 systems sold. HIGHLIGHTS compact table machine simple operability 3-axis stepper motor control with path operation Ball screws 2-phase stepper motors CNC control software included Mosaic Safety Circle POPULAR MATERIAL Foam Plastics ACCESSORIES Length gauge Spindles (iFM1000ER, iFM1000WS) Quick clamping system Spannzangen Suction device

Condition: new, functionality: fully functional, machine/vehicle number: 246203 xxxx, Ideal basis for setting up CNC machines and applications The FB2 flatbed unit is ideal for getting started with CNC technology and is ideal for model making and hobby applications. The FB2 is also often used in industry for measuring and dosing technology, as it offers extensive expansion options. The unit also offers access to the isel modular system. Various sizes from travels of 530 x 500 mm to 1030 x 1250 mm and extensions such as base frame and housing are available and can be individually combined. Pedpfx Ajhqmamof Sjha BEST SUITABLE FOR: • modular isel building block system • universal range of applications • easy handling • ideal for laboratory, model making and workshop use • assembly and mounting • printing and engraving • drilling and milling • dosing and screwing • forming and modeling • gluing and casting • soldering and welding • measuring and testing • sawing and cutting and much more Z-passage = 190 mm (Z-passage = 300 and 500 mm on request!) FEATURES: • durable stepper motors in the 200 W range • reliable LES units with steel ball screws are installed as drives • clamping of workpieces using a T-slotted plate • available with and without protective cover • variable gantry apertures, depending on customer application OPTIONS: • iSA milling spindles and water-cooled HF milling spindles • Cooling spray device • Cold air cooling, Cool-Min • Automatic tool length measurement • Rotation units • Workpiece clamping systems (hand lever, vacuum clamping tables, etc.) • Suction systems • LED machine room lighting • RAL color selection • CAD/CAM-Software • Diffusers 190 mm, 300 mm or 500 mm • Powerful 4-axis control controller • Underframe • Enclosure with sliding/folding door

Condition: excellent (used), Year of construction: 1995, functionality: fully functional, High precision drilling and milling machine Fehlmann model Picomax 51 CNC Heidenhain TNC 360 very good condition CE conform Hthrgw39X Technical Data: >> Year of construction: 1995 >> Travel X/Y/Z 420/ 240/ 120 mm >> Travel distance W 450 mm >> Clamping surface (L x W) 730 x 280 mm >> Permissible table load 75 kg >> Distance table - spindle nose 0 - 560 mm Pjdpfx Afjuxprlo Ssha >> Feed speed X/Y 1 - 7200 mm/min >> Feed speed Z 1 - 3600 mm/min >> Tool quick-change system SF 32 >> Infinitely variable speed range 9200 rpm >> Drive power 4 kW >> Space requirement approx. (W x D x H) 2.0 x 1.5 x 2.4 m >> Fourth axis dividing head About the machine : We offer a high-precision drilling and milling machine Fehlmann model Picomax 51 CNC in very good condition with CE conformity. It has a Heidenhain TNC 360 contouring control. The program creation in the user-friendly Heidenhain plain text dialog is particularly easy. HEIDENHAIN TNCs are workshop-oriented contouring controls with which you can program conventional milling and drilling operations directly on the machine in easy-to-understand plain-language dialog. The tool holders (see pictures) are included. Mechanically and electrically tested. Take the opportunity to inspect and try out this machine under power on site.

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: L13 1320, CNC lathe FEMCO HL25 Phjdpeuliyhefx Af Soa Year of manufacture: 2003 Machine number: L13 1320 Control: FANUC Series 18-T Further information on request!