Lathe

Weiler Primus

Condition: good (used), Year of construction: 1981, machine/vehicle number: 283, Item No. 26208 Technical Data: - Maximum turning height 120 mm - Maximum turning diameter 450 mm Gkedpfxszyl H He Agled - Maximum swing over bed 250 mm - Spindle bore 23 mm - Spindle mounting with threaded nose DIN 55027 - Taper of tailstock spindle MK 2 - 20 spindle speeds 60 - 3000 rpm - Feeds - longitudinal 0.03 - 3.0 mm - transverse 0.015 - 0.150 mm - Thread pitches 0.25 - 5 mm - Drive 400 V / 1.1 / 1.5 kW - Footprint approx. approx. W 1200 x H 1250 x D 650 mm - Weight approx. approx. 700 kg - Including: - 3-jaw chuck - Quick-change tool holder - Rotating center - Separate tool cabinet with various accessories

Condition: used, L + Z lathe WEILER, Type Condor 81 A Machine No. 36553, Year of manufacture approx. 1985 Distance between centers 750 mm Swinging diameter over bed 330 mm Distance between centers above bed 165 mm Swinging diameter over cross slide 180 mm Distance between centers above cross slide 90 mm Spindle bore 40 mm Chuck mount Short taper DIN 55027, size 5 Tailstock internal taper MK 3 Tailstock quill travel 110 mm Spindle speed 45 - 2800 rpm, 16 steps Drive power 3 kW Mains connection 400 Volt, 50 Hz - Spindle speed via 16 gear stages - 3-jaw chuck Ø 160 mm RÖHM with boring and turning jaws - Quick-change tool holder Multifix size B with 3 inserts - Automatic feed in longitudinal and facing directions - Electro-mechanical spindle brake - Emergency stop - Coolant tank with pump in the machine base, without supply line to the work area - Folding chuck guard - Splash guard Gksdpfxek S Ht Ae Aglsd - 1 rotating center - Electrical diagram and operating manual Space requirement L x W x H 1850 x 950 x 1400 mm Weight 1100 kg Good condition

Condition: used, Year of construction: 1999, turning diameter over bed 280 mm Gedpfx Agez Abw Hjlskd turning diameter over slide rest 150 mm turning length 500 mm center height over bed 140 mm centre distance 500 mm bed width 205 mm spindle bore 40 mm turning speed range - stepless 30 - 4.000 U/min 3-jaw-chuck diameter 140 mm quick change toolholder MULTIFIX Typ A drive capacity - spindle motor 4,0 kW taper in tailstock-quill MK 3 dia. of quill 40 mm quill stroke 85 mm voltage 400 V total power requirement 7,5 kW weight of the machine ca. 800 kg dimensions of the machine ca. 1,40 x 0,95 x 1,55 m - Serial-No.: 154 - SIEMENS 3-axis digital display - MULTIFIX quick-change tool holder - rotating centering tip

Condition: used, Year of construction: 2000, turning diameter over bed 280 mm turning dia. over face-slide 150 mm centre height 140 mm turning length 500 mm main drive stepless adjustable 0 - 6.000 U/min spindle speed 30 - 5.000 U/min max. workpiece weight between centers 100 kg quill stroke 85 mm total power requirement 4 kW weight of the machine ca. 800 kg dimensions of the machine ca. 1430 x 950 x 1550 mm Bed Slide (Z-Axis): - Guide length of the bed slide: 350 mm - Bed width: 205 mm - Slide travel: 500 mm - Max. feed force: 3500 N Flat slide (X-axis): - Slide travel: 150 mm - Slide width: 140 mm - Max. feed force: 2500 N Gkjdpfx Agsz St Nxoled Upper slide (Z-axis): - Slide travel: 100 mm - Slide width: 92 mm - Swivel range of the cross slide: 75 °

Condition: used, L + Z lathe WEILER, type LZ PRIMUS GS Machine no. 1984, year of manufacture 1981 Distance between centers 400 mm Turning diameter over bed 250 mm Height of centers over bed 125 mm Turning diameter over carriage 140 mm Height of centers over carriage 70 mm Spindle bore 24 mm Spindle speed 60 - 3000 rpm, 18 steps Feed in longitudinal and facing directions Chuck flange, short taper DIN 55022, size 4 Tailstock internal taper MK 2 Drive power 1.1 kW and 1.5 kW, pole-reversing Power supply 380 volts, 50 Hz - Spindle speed controlled via 2 motor speeds and 9 gear stages - 3-jaw chuck WEILER, Ø 125 mm, with soft jaws - Quick-change tool holder MULTIFIX with 2 interchangeable cassettes - Coolant system - Collet set Ø 3 / 4 / 5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 / 14 / 15 / 16 / 18 / 20 mm - 1 centering point for collet chuck - Turning center flange - Emergency stop - Folding chuck guard with electrical monitoring - Splash guard Space requirement L x W x H 1200 x 650 x 1380 mm Weight 325 kg Gksdjz N H Dqepfx Aglod Good condition

Condition: good (used), Year of construction: 1987, CNC turning machine WEILER Primus 2 CNC, serial number 151, CNC control system by Bosch. Gsdpez R R Eijfx Agljkd

Condition: like new (used), functionality: fully functional, Weiler Primus Lead and Pull Spindle Bench Lathe – Like New Condition!!! Technical Data: >> Year of manufacture approx. 1990, machine no. 4472 >> Center height 120 mm >> Distance between centers 430 mm >> Speed: 60 - 3000 rpm in 18 gear stages >> Spindle bore 23 mm >> Short taper spindle head DIN 55027 >> Tailstock MK 2 >> Feeds from 0.03 to 0.15 mm/rev >> Possible threads: Metric, inch, module, and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 three-jaw chuck, 125 mm, like new, with 2 sets of jaws >> Collet chuck with collets from 2 mm to 12 mm, increasing in 1 mm increments >> Mulifix size A with 3 steel holders >> Change gears >> Fixed steady rest >> Faceplate >> Spindle guard >> Operating manual, electrical diagrams, and much more About the machine: Gksdpfxez A Tgqj Aglod A Weiler Primus Lead and Pull Spindle Bench Lathe with a workbench is offered in like-new condition. The machine is, of course, fully functional. All slides run very smoothly and evenly. Even at high speeds, the Weiler runs quietly. This Primus model comes from the German Armed Forces, where it was used very little (almost new). This newer generation of Weiler lathes is very user-friendly and can produce surfaces that are as smooth as if they were ground. Take advantage of the opportunity to inspect this machine on-site and under power to convince yourself of its condition. Digital display available for an extra charge.

Condition: excellent (used), functionality: fully functional, Weiler Primus guide and spindle lathe from the training workshop!!! Technical data: Godpfxovtp Ede Aglskd >> Year of manufacture approx. 1985 Machine no. 1191 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear stages >> Spindle passage 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm / rev >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 x three-jaw chuck 125 mm with 2 sets of jaws >> Collet device with Collets 18 pieces >> Mulifix size A with 3 steel holders >> Stop >> Electric spindle protection About the machine: A Weiler Primus guide and pull spindle lathe is offered in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs quietly even at high speeds. The Primus was in a training workshop. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site with power on and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus lead and feed screw lathe from training workshop !!! Technical data: >> Year of construction approx. 1985 >> center height 120 mm >> center distance 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle clearance 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 piece three-jaw chuck 160mm with 1 set of jaws >> 1 new three-jaw chuck 125mm with 2 sets of jaws >> Collet chuck device with collets from 1 mm to 20 mm 1 mm increasing Gkedpfx Agsu Aftgolod >> Mulifix size A with 3 steel holders >> Fence >> Change wheels To the machine : We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs smoothly even at high speeds. The Primus was used in a training workshop. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to inspect this machine on site under power and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus LZ/G lead and feed screw lathe in special paint finish light gray !!! Technical data: >> Year of construction ca.1990 Machine-No.3150 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> spindle passage 23 mm >> Short taper spindle head DIN 4 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev Gkjdevivmyopfx Agled >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Switchable spindle brake >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 piece three-jaw chuck NEW 125mm with 2 sets of jaws >> Mulifix size A with 2 steel holders >> collet chuck device new with collets from 3 to 26mm 1 mm increasing new >> To the machine : We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run smoothly and evenly. The bed guides are in very good condition. The Primus was used in a training company. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and see the condition for yourself.

Condition: excellent (used), functionality: fully functional, Weiler Primus LZ/G, machine number 2679, in excellent condition, with draw and lead screw. Includes 3 chuck jaws 125mm, tool holder, and 4x Multifix AD2090 tool holders. Godpez Eqn Defx Agljkd Can be inspected and tested while powered on.