Welding turn table

Protec W 20 000

Condition: new, Year of construction: 2025, Protec Welding Turntable, 5000 kg load capacity Variable speed control, 0.05 - 0.5 RPM Bodpfx Asid Szcscfjlp Handheld remote control Height: 600 mm Diameter: 1500 mm Foot pedal remote control available at an additional cost.

Condition: new, Year of construction: 2024, Protec KT 10000 welding positioner Complete set with hand-held remote control 10,000 kg load capacity Bodsid Szvspfx Acfslp Diameter of the clamping plate: 2000 mm Height when tilted: up to 1600 mm to the center Height in horizontal position: 1920 mm Speed: continuously adjustable from 0.01 to approximately 0.35 RPM (higher speeds possible) Tilting angle: up to 120° Length: 2800 mm Width: 1920 mm Foot pedal remote control available at an additional cost of €390.

Condition: new, Year of construction: 2024, Protec Welding Positioner, 10,000 kg load capacity Speed continuously adjustable, 0.05 - 0.5 RPM Hand-held remote control Bjdpfx Asid Szgscfolp Foot-operated remote control, additional cost: €390 Height: 650 mm Diameter: 1600 mm

Condition: new, table diameter 2000 mm table load 10000 Kg swivelling range 0 - 130 Grad turning speeds 0,02 - 0,2 U/min height adjustment 1450 - 2200 mm max. torque on the faceplate 20000 Nm engine output 1,5 / 2,0 kW welding current 1000 Ampere - Manual height adjustment. - Self-locking gearbox, therefore hardly any pre and after-run at eccentric Load. - Electronic components from Schneider, Siemens and Delta. Blodpfsfv Ay Isx Acfep - Frequency-controlled, stepless speed of the turntable. - High stability due to the robust construction. - CE certificate. The D-HBE series comes as a standard version with a cable remote control and a footswitch.

Condition: used, Year of construction: 2017, controller model: NEXUS, _____ Description: Year of manuf. : 2017 Material thickness : 14 mm Technical data Working length:3,100 mm Bending capacity / Folding capacity:14 / 12 mm Upper roll diameter:290 mm Lower roll diameter:270 mm Side roll diameter:210 mm Main motor power:7.5 kW Machine length:4,475 mm Machine width:1,460 mm Machine height:1,520 mm Machine weight:8,000 kg Control system:NEXUS TouchScreen DNC equipment :- NEXUS DNC control system with touchscreen interface :Programming and operation options: :1. Manual mode – all movements controlled via joystick :2. Teach-in mode – saving of positions :3. Input of values for the rollers via the screen :Storage capacity for 300 programmes : :- Rollers made from C45 alloy steel, induction-hardened :to 50–55 HRC : :- Conical bending unit with both :side rollers set at an angle, lower roller set at an angle and :bearing with hardened guide roller : Bodpszuikxefx Acfjlp :- Calibration unit for re-rounding :welded tubes : :- Brake for the upper roller for greater precision when :positioning the material.

Condition: good (used), Year of construction: 2003, sheet width 2050 mm plate thickness 10.0 mm ST pre-bending 8.0 mm ST diameter of upper rolls ~ 220 mm side roll diameter ~ 170 mm diameter of lower rolls ~ 190 mm bending speed ca. 2.0 + 5.0 m/min Control ELAP LYNX oil volume 80.0 Liter voltage 380 V total power requirement 5.5 kW weight 5000 kg range L-W-H 3500 x 1550 x 1400 mm Current new price incl. accessories: approx. € 90.000 Special price on request Equipment: - Robust electro-hydraulic 4-roll plate bending machine - 4-roll design offers a wide range of bending and rolling capabilities - MG NC control unit "ELAP LYNX" * Operation – control of all rolls and machine axes * Digital position display * Manual operation via joysticks * Movable control panel - Two central rolls driven directly by hydraulic motors - Conical rolling possible via roll tilting - Side roll parallelism maintained via torsion shafts - Pre-bending on both ends - Diameters up to 1.1 times the top roll diameter are possible Bsdsz N Hxhjpfx Acfelp - Forged and hardened rolls (hardness: 53–55 HRC) - Low-maintenance, robust machine design - Permanent lubrication for all bearings - Sturdy welded steel construction - Selectable bending speeds (2 settings) - Electro-hydraulic drop-end bearing for easy removal of rolled parts - Pressure gauge/display for rolls - Safety system (safety trip wire with switch unit) - Operating manual (PDF)

Condition: new, table diameter 2000 mm table load 10,0 t swivelling range 0 - 135 Grad turning speeds 0,05 - 0,5 U/min max. torque on the faceplate 20000 Nm table pass 200 mm welding current 1000 Ampere total power requirement 3,0 + 4,0 kW weight of the machine ca. t Bsdpfjfv Axijx Acfjlp ELDING TABLE WITH LARGE THROUGH BORE • Self-locking gearbox, no pre- or after-run with eccentric load. • Electronic components from Siemens and Schneider. • Frequency-controlled, very accurate speed control. • Turntable with large through hole and T-slots. • High stability through a clever construction. • CE certificate. • Very good price / quality ratio. • The D-TLP series comes with remote control and foot pedal (left / right). No original pictures. Design but identical.

Condition: new, table diameter 1800 mm table load 8 t swivelling range 0 - 130 Grad turning speeds 0,02 - 0,2 U/min 16000 Nm 0 1,1 / 2,2 kW welding current 1000 Ampere Bljdpfxsi Hg Ive Acfep including remote control and welding current transmission.

Condition: used, functionality: fully functional, Year of construction: 2004, machine/vehicle number: 4roll, control type: manual, degree of automation: manual, actuation type: hydraulic, controller manufacturer: Davi, controller model: digital position readout, number of rollers: 4, roller (bottom) diameter: 155 mm, roller (top) diameter: 165 mm, side roll diameter: 120 mm, sheet thickness (max.): 6 mm, sheet thickness steel (max.): 6 mm, sheet thickness stainless steel (max.): 6 mm, sheet thickness aluminum (max.): 8 mm, sheet thickness brass (max.): 8 mm, sheet thickness copper (max.): 8 mm, overall weight: 2,200 kg, total length: 3,400 mm, total width: 1,150 mm, total height: 1,100 mm, input voltage: 400 V, input frequency: 50 Hz, number of digital displays: 2, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, 4roll 2000x6 mm plate bending machine Davi year 2004 used plate roll in working condition, Planetary hydraulic dual pre-pinch Capacity: Plate width 2000 mm plate thickness 6 mm pre-bend 5 mm minimum rolling ID 220 mm rollers length 2050 mm Upper roll D 165 mm Pinch roll D 155 mm Side rolls D 120 mm Power electric motor 3 kw on hydraulic unit Voltage 3ph 400/50 mm Installed configuration Rollers surface hardened high strength Conical plate rolling, cone bending Hydraulic control manual leverage distributors Variable working speed Digital position readout --- Hydraulic driven motorized central rolls Pre-pinch pressure adjustable pre-bend Drop-end open unloading fully round shells Calibration system for welded seam re-rolling Safety and emergency stop Bledpo Ahg Ayefx Acfop machine dimension 3400x1150xH 1100 mm -weight 2200kg