Briquetting Press

muetek MAP 1200

Condition: good (used), Used machine, good condition. E27N38Yny Delivery time appr. 19 weeks after ordering Basic machine starts at 139.700 € net *Options at additional cost, see below Briquetting press e.g. for wood dust, spelled husks, activity material (e.g. for pigs to play and nibble around), animal feed, lucerne or wood shavings. *Optionally, short briquette tablets can be made Technical specifications: Throughput capacity up to a maximum of 750 kg/h (depending on the material) (e.g. sawdust with a bulk density of 250 kg/qbm) An exact statement about the throughput is only possible after a test with your material. Can vary greatly depending on the bulk density of the starting material. Goods tariff number: 84793010 Briquette Ø 65 mm including 2 m press channel Engine power main engine 37 kw Feed screw geared motor 2.2 kw Compressor screw 5.5 kw Hydraulic pump motor 0.37 kw Total connection value: approx. 47 kW Control panel with plain text display for operating states and utilization indicator for the main drive and feed screws PLC control with operating hours counter in the control cabinet Machine has CE mark Automatic start-stop function Dimensions 3100x860x1800 mm lxwxh Weight 3800kg Options at extra cost: Temperature control unit for the pressing tools to maintain the temperature for optimal briquette quality. Temperature controller for pump, cooling unit, fan, pressostat Wired ready for connection - absolutely necessary for operation including the corresponding control + €7,850 net guillotine or pill crusher, for cutting the briquettes to length + €6,900 net Necessary for compressed air connection! Silo for MAP series + €19,940 net - Storage silo above the machine - Content approx. 6 sqm, stable steel construction with agitator discharge and level indicator. Transport line / cooling section (nominal value: 4x2m) each 2 meters 990 euros net Control System 4.995 € net Assembly / commissioning (nominal value approx. 2-3 days on site) according to expenditure on proof against separate calculation. The following sentences apply: Service technician/mechatronics technician per hour of assembly and travel: €129.00 Overtime: 25% surcharge 50% surcharge for each Saturday and night hour 100% surcharge for each Sunday and holiday hour Release per mechanic per day: depends on the country Per car and van and driven kilometer: 0.98 € / km Arrival and accommodation against receipt or flat rate billing at the expense of the client. . Test with the respective customer material: (by arrangement, up to a maximum of 750 kg) - 1,970 € net . Raw material requirements: - The moisture content (atro) must be between at least 6 and a maximum of 15% - Maximum chip length 18 mm - Installation temperature: room with a temperature of at least +5°C - The charge must be free of metals and mineral impurities. This can result in damage to the pressing tools and/or increased wear

Condition: as good as new (ex-display), Year of construction: 2023, Special price for our prefeeder Another machine, available immediately (ex works Neckartailfingen) approx. 24 operating hours. Including: + profile rotor for increased throughput Options: Double row of knives + 895 € net Veneer and paper scraper + 970 € net * Recommended for extremely thin materials with a thickness of less than 3 mm Our mütek MRZ 530 single-shaft shredder shreds a wide variety of materials such as all types of waste wood, softwood, chipboard and hardboard, pallets, construction timber, demolition wood, carpet, cable, paper, cardboard and plastics. The machine is characterized by its robust design, which guarantees consistent quality in continuous operation. We will be happy to carry out a free test with your material. We invite you to visit us in Neckartailfingen. It is also possible for you to send us your material by freight forwarder and we can document the test with pictures and videos. Machine data: Motor: 15 kW; 400 V - 50 Hz - 3 ph, Blades: multi-rotatable, Rotor diameter: 260 mm, Control: PLC Siemens S7-1200, Hopper (mm) 510 x 810 mm, Hopper volume approx. 0.4 qbm, throughput 1 - 5 hopper fillings / h, hydraulically operated pusher, Screen perforation of your choice (10 - 40 mm), suction nozzle Ø 160 mm, Weight approx. 1,000 kg, Dimensions approx. 1550 x 1100 x 1640 mm, Moisture content of the raw material: must be below 30 % atro. Included as standard: - Fast hydraulics - Profile rotor - Switch cabinet with Siemens PLC control - Automatic star/delta start - Automatic OFF when the rotor is idling - Removable suction chute - Speed 70 - 100 rpm for higher throughput capacity - Cycle control to avoid idle times - Performance-enhancing step control of the hydraulic slide - Stable guides for the hydraulic slide Igkchryd0 Other shredder options: - Raise shredder by 30 cm (preparation for conveyor belt) +1,980 € net - Folding conveyor belt +8,770 € net Horizontal part: 1200 mm Rising part: 2500 mm Angle: 0-60 degrees adjustable Discharge height: approx. 2000 mm + - 100 mm - Overbelt magnet + 5.980 € net - Conveyor belt and overbelt magnet control + € 2,750 net (start and stop synchronized with the chipper) . Requirements for the output or raw material: - The moisture content (atro) must be below 30% - Metals and mineral impurities such as sand, stones, etc. lead to increased wear

Condition: like new (used), Year of construction: 2023, operating hours: 230 h, Functionality: fully functional, total width: 2,430 mm, total height: 1,735 mm, total length: 2,410 mm, overall weight: 3,500 kg, type of input current: three-phase, input current: 100 A, input voltage: 400 V, type of motor: three-phase motor, power: 37 kW (50.31 HP), motor voltage: 400 V, Equipment: emergency stop, Slow-speed shredding system now available +++Conveyor belt and overhead magnet included+++ >>> mütek shredding system Includes: 2nd row of knives for up to 30% more throughput Fast hydraulics for increased throughput Conveyor belt removal Your advantages: + Extremely large cutting unit opening; 1300x1200mm + Special rotor suitable for hardwood and softwood + Energy-efficient and powerful with 37 kW starting power Technical specifications: Top feed opening (mm): 1300 x 1200 Hopper capacity (cbm): 1.6 m³ Rotor diameter (mm): 368 Rotor speed (rpm): 65 - 125 Power requirement (kW): 37 Screen perforation (mm): 20 (retrofittable 10-40mm by the manufacturer) Tools: 37/70 blades Suction nozzle diameter (mm): 200 mm Dimensions: 2430x2410x1735 mm (lxwxh) Weight (approx. kg): 3500 -- Raw material requirements: - The moisture content (dry) must be below 20% - The feed must be free of metals and mineral contaminants. Damage to the tools and/or increased wear may result. >>> Conveyor Belt L-Shaped Conveyor Belt MRZ Including preparation for conveyor belt removal Horizontal section: 1200 mm Rising section: 2500 mm Discharge height at 60 degrees: approx. 2000 mm Bending angle adjustable from: 0 to 60 degrees Drum diameter: 63 mm Belt width: 400 mm Usable width: 350 mm Cleave spacing: 200 mm Cleave height: 30 mm Lateral guide: aluminum, sealed with belt flaps Feed height: 300 mm Discharge height: 2000 mm Motor: 0.25 kW, 400 V, 50 Hz, 3 ph Conveyor speed: 36 m/s No control unit! >>> Automatic metal separator consisting of: Neodymium overband magnet (Neodymium magnets are among the strongest magnets in the world. They have extreme pulling force and cannot be compared to ferrite magnets) Extremely high separation efficiency of up to 99.4%, depending on the pile height and the feedstock. Arguably the most compact overband magnet on the market. Competitors often use the less powerful ferrite magnets to save costs. High-performance neodymium magnet approx. 600 x 68 x 36.5 mm * Nails are attracted over a length of 600 mm and ejected to the side, in the non-magnetic area. This overband magnet should be mounted approximately 5 - 9 cm above the material flow. Ideal for separating nails from wood chips. Requirements: * Belt width or internal usable width (of the existing conveyor belt) must be less than 55 cm. * Suitable for separating nails from material flows less than 12 mm high, and chip length less than 25 mm. Control: Manual start-stop A 16 A power supply is required. >>> Includes control link Shredder ON - Conveyor belt ON - Metal separator ON Drguvn Shredder OFF - Conveyor belt OFF - Metal separator OFF AUTO-OFF when shredder is empty. >>> Platform with stairs made of solid wood, adapted to the machine

Condition: excellent (used), Functionality: fully functional, - Offer number: 5/99 - Ultrasonic Measuring Instrument, PDA Penetration Dynamics Analyzer (Surface + Sizing Tester) - Manufacturer: Emtec & Mütek - Type: PDA.c 02 measuring device - Serial number: S-Nr90-03-19-16-0032 - Module S serial number: 0102-04-22-16 - With PC and software, keyboard, monitor and house - With hand roller 200 mm wide - Incl. operating instructions / software description - Test liquids: Coating color, water, water-isopropyl alcohol mixture, mineral oil, inorganic and organic liquids of low to medium viscosity. - Paper and cardboard up to 600g/sqm - Measurement of surface properties of paper and cardboard - Voltage 110 V, 60 Hz and 220 V, 50 Hz - weight approx.: device 19 kg and accessories 8 kg - optical condition according to photos - used Bfhiktjact - functional Notes: The goods offered here usually come from company liquidations and insolvencies. Due to missing nameplates it is not always possible to give exact item data. The item pictures are original photos that show the actual item condition. If several identical items are offered, only one of the items is photographed. There may be slight variations in the item condition of the individual item. Should an item be opened or repaired/rebuilt by the buyer, any warranty claim will be void. This also applies if repairs and modifications are carried out by third parties without prior agreement. Used company names and brand

Condition: used, Year of construction: 2021, Used machine Year of manufacture 2021 525 operating hours Dust extractor Extraction nozzle diameter 350 mm Motor 11 kW, 400 V, 50 Hz Max. volume flow 8000 m³/h Nominal volume flow at 20 m/sec: 6950 m³/h Negative pressure at the total connection at 20 m/sec: 2630 Pa Filter: 23 cartridge filters Filter area 71 m³ H3 "GS dust tested residual dust content < 0.1 mg/m³ Bpzmg00J Pneumatic JET filter cleaning (compressed air supply on site) Compressed air connection 3/4 inch, connection pressure 7-12 bar with 50 NL/min Operating pressure in the device 6 bar Extinguishing device with powder extinguisher, dry fire extinguisher 12 kg Frequency converter Weight approx. 865 kg with briquetting press MPP 60 Briquette diameter 50 mm Throughput (depending on material) max. 60 kg/h (based on a bulk density of 200 kg/m³ Motor power 5.5 kW Oil quantity 110 l Silo diameter 1000 mm Silo content; approx. 0.7 m³ Pump 27 l Hydraulic pre-compressor with oil hydraulic cooling with fill level monitoring Incl. special container for RL 350 Floor area approx. 2200 x 1100 x 3100 mm Availability: short term Storage location: Flörsheim

Condition: excellent (used), Year of construction: 2012, Description: Automatic film welding machine with downstream shrink tunnel. Can be used for all products that can be fed via the discharge table, e.g. wood briquettes. The machine is equipped with a conveyor belt to transport the packages through the shrink tunnel. The throughput time through the tunnel can be adjusted depending on the film thickness. The motor drive of the film rolls doses exactly the length of film required for the respective package. Work flow: The briquettes are placed manually on the table in the adjustable discharge frame. The two-hand operation triggers the discharge of the briquettes into the film curtain and the subsequent separation and sealing process. The package, now loosely wrapped in film, is picked up by the conveyor belt of the shrink tunnel and transported through the shrink tunnel. The film fits tightly to the contours of the package. After the now film-wrapped package has left the shrink tunnel, it should be left to cool for a while on an additional roller conveyor (see offer) so that the film hardens. The package can then be placed/stacked on a pallet. Technical data: Semi-automatic briquette band rolling machine with integrated single-chamber shrink tunnel for PE flat films 40-100. - Product feed into the machine via two buttons - Cycle output up to max. 8-10 containers/min. - Both film roll unwinders are motor-driven - Tunnel belt with frequency-controlled adjustable speed and adjustable air flow - Tunnel belt consisting of fiberglass rods with driven central chain, load capacity up to 30 kg. - Automatic tunnel switch-off - 760 mm welding bar - Max. roll size: 750 mm x 350 mm (WxD) Drbebh - Product sizes: - 20-380 mm, 110-630 mm, 100-410 mm (HxLxW) (not all dimensions can be combined with each other.) - Product weight: 2-30 kg. - Control with 10 storable programs, piece counter, recording of product length - Machine can be moved on wheels and feet - Technical data: 400 V, 17 kW, 32A CEE plug, 6 bar constant, 17.6 NL/container - Machine weight: 600 kg. - Machine dimensions: 2890 mm x 1243 mm x max. 2065 mm (LxWxH) - Cooling fan group - Pressure rollers right and left at the tunnel exit - Light grid at the machine entrance -> one-hand operation

Condition: excellent (used), CATALOGUE NUMBER 6901 TECHNICAL DATA - max. turning length 1200mm - max. turning diameter 210mm - max. turning diameter with standard steady rest 90mm Cqkhhjvzx3 - max. size of square material for turning with automatic feeding 100mm - 3 hydraulic copiers - additional 3 knives on hydraulic pistons (2 pieces installed) - 4 types of spindle speeds - automatic or manual machine operation - 9kW headstock spindle motor - 3kW hydraulic pump motor - diameter of the exhaust port 90mm - dimensions for transport length/width/height 3700x2100x2000mm - weight approx. 3000kg ADVANTAGES - Italian production - automatic hydraulic copier - original DTR documentation - unpainted - used lathe, condition very good Net price: PLN 69,900 Net price: EUR 16,447 Net price calculated according to the exchange rate of PLN 4.25/EUR (in case of larger exchange rate fluctuations the price may change)

Condition: as good as new (ex-display), Year of construction: 2024, Special machine for shredding plastics Basic machine from €24,990 net Well suited for shredding: - Paper, cardboard boxes, pipes, profiles, boxes, canisters, buckets, cans, sections of wooden pallets, etc. - Medium-hard thermoplastics such as PVC, PP, PE, PS, PU, PET Includes: - special rotor with embedded blades (reduced load capacity), - small cutting gap between blade and counter blade Motor: 18.5 kW; 400 V - 50 Hz - 3 ph Control: PLC Top cutting unit opening 600 x 800 mm The parts should be a maximum of approx. 500x500 mm in size *the height is less important hydraulically operated slide, sieve hole of your choice (25 - 40mm) For plastics, coarser sieves are recommended (30-40 mm) *If you want to shred more finely, a two-stage shredding process is recommended with downstream granulator type MVZ (sieves 5-15 mm) Suction nozzle Ø 160 mm Weight approx. 1,300 kg Dimensions (lxwxh) approx. 1737 x 1167 x 1650 mm Other options available for an additional charge: - Raise the shredder by approx. 25 cm (Preparation for conveyor belt removal) + €995 net - Angled conveyor belt (discharge height approx. 220 cm) + €8,490 net - Overband magnet + €6,750 net - Control of conveyor belt and overband magnet + €2,495 net (Start and stop synchronized with the chipper) - Alternatively, manual start and stop on the conveyor belt + €497.50 net . Requirements for the raw material: - The moisture content (atro) must be below 25% - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear. . We would be happy to carry out a free test with your material. We invite you to come to us in Neckartailfingen. It is also possible for you to send us your material by freight forwarder and we will document the test with pictures and videos. --- *only for brittle plastics with a medium degree of hardness, *not for elastic or extremely hard and heavy plastics - this would affect the durability of the system. --- Beksd3Tlzt Optional would be the next larger machines Basic machine: Shredder MGZ 830 K-S - 18.5 kW Cutting unit opening at the top 800 x 1,000 mm The parts should be a maximum of approx. 720x700 mm *the height is less relevant from €39,995 net * Options depending on the effort Basic machine: Shredder MGZ 1030 K-S - 22 kW Cutting unit opening at the top 1,000 x 1,000 mm The parts should be a maximum of approx. 900x700 mm *the height is less relevant from €49,975 net * Options depending on the effort Basic machine: Shredder MGZ 1330 K-S - 37 kW Cutting unit opening at the top 1,300 x 1,200 mm The Parts should be a maximum of approx. 1,200x700 mm in size *the height is less relevant from €79,975 net * Options depending on effort

Condition: refurbished (used), Year of construction: 2011, operating hours: 855 h, Hako Jonas / Sweepmaster 1200 D Refurbished sweeper with complete engine overhaul - with 6 months warranty and new DGUV V3 test including test report. Working width with two side brushes: 116 cm Central sweeping roller: 80 cm Area performance max.: 10400 m²/h Container capacity: 130 l Drive type: diesel engine - LOMBARDINI New parts installed / repairs carried out: Dqvwc7 - Refurbished diesel engine - All drive belts new - All ball bearings on the deflection rollers new - New heavy-duty wheel at the front - All rubber strips new - New box filter/hydraulic filter/oil filter/air filter - All oils new - Sweeping unit completely overhauled We also offer: Service, repair and sales for all common Hako models.

Condition: new, Year of construction: 2025, Model ML-1200 Infrared protection Automatic oil system Max. sheet size 1200X820(mm) Machine speed(Strokes/Min) 20±2 Max.Rule Length(m) Ctebtcowuc

Condition: as good as new (ex-display), Year of construction: 2023, Special price for our prefeeder Another machine, available immediately (ex works Neckartailfingen) approx. 24 operating hours. Suitable for shredding all types of waste wood and pallet offcuts. The pallet should be prepared with the jigsaw or chainsaw so that it fits upright in the hopper - see picture 2. 40x20x20 cm would be ideal so that the wood can lie flat on the pusher floor. This is where the machine works most effectively. At the bottom of the shredder there is a hydraulic pusher which presses the wood against the rotor depending on the load. The material is shredded until it passes through the screen basket. Throughput of up to 200 kg per hour *depending on the screen and how well the material is prepared. *Conveyor belt and overbelt magnet at extra charge. + Powerful 18.5 kW motor, + concave knives, + large high-performance gearbox, + special, load-dependent pusher control, Jux3Pi Product code: 84659600 Motor: 18.5 kW; 400 V - 50 Hz - 3 ph. Knives: 15 pieces, multi-rotatable Option double row of blades + 995 € net Rotor diameter: 260 mm Control: SPS Siemens S7-1200 Cutting unit opening 630 x 820 mm Filling volume approx. 0.6 qbm Hydraulically operated pusher Screen perforation of your choice (10 - 30 mm) Suction nozzle Ø 160 mm Weight approx. 1,300 kg (depending on accessories) Dimensions (lxwxh) approx. 1737 x 1167 x 1650 mm Moisture content: ᐸ 30 % Atro . Included as standard: - V-rotor for maximum throughput - Switch cabinet with Siemens PLC control - Automatic star/delta start - fast hydraulics - auto. OFF when the rotor is idling - speed 70-90 rpm for high throughput capacity - Cycle control to avoid idling times - Performance-enhancing step control of the hydraulic slider - Pertinax guides for hydraulic slide - Vibration-damping machine feet - CE Conform. - MADE IN GERMANY . Shredder options: - Raise shredder by 30 cm (preparation for conveyor belt) + €2,080 net - Folding conveyor belt +8,770 € net Horizontal part: 1200 mm Rising part: 2500 mm Angle: 0-60 degrees adjustable Discharge height: approx. 2000 mm + - 100 mm - Overbelt magnet + € 5,980 net - Conveyor belt and overbelt magnet control + € 2,750 net (start and stop synchronized with the chipper) - Hopper adjustment + 940 € net - Eco rings: + € 1,980 net (recommended for more than 15 % hardwood) - Special scraper + 990 € net (recommended for veneer or paper) - Double row of knives + 995 € net . Requirements for the raw material: - The moisture content (atro) must be below 30% - Metals and mineral impurities such as sand, stones etc. lead to increased wear.

Condition: as good as new (ex-display), Year of construction: 2023, Demonstration machine with approx. 20 operating hours Another machine, available immediately (ex works Neckartailfingen) *Options at extra charge - see below Included: + Profile rotor for higher throughput We will be happy to carry out a free test with your material. I would like to invite you to our premises in Neckartailfingen. It is also possible for you to send us your material by forwarding agent and we can document the test with pictures and videos. Motor: 18.5 kW; 400 V - 50 Hz - 3 ph Knives: 15 pieces, multi-rotatable, Option double row of knives + 995 € net Rotor diameter: 260 mm Control: SPS Siemens S7-1200 Cutting unit opening 630 x 820 mm hopper volume approx. 0.6 qbm hydraulically operated slide Screen perforation of your choice (10 - 40 mm) Suction nozzle Ø 160 mm Weight approx. 1,300 kg Dimensions (lxwxh) approx. 1737 x 1167 x 1650 mm Moisture content: < 30 % Atro. . Included as standard: - V-rotor for maximum throughput - Switch cabinet with Siemens SPS control - automatic star/delta start - fast hydraulics - auto. OFF when the rotor is idling - speed 70-90 rpm for high throughput capacity - Cycle control to avoid idling times - Performance-enhancing step control of the hydraulic slide valve - Pertinax guides for hydraulic slides - Vibration-damping machine feet Ry2Ojkfiu - CE Conform. . Shredder options at extra charge: - Raise shredder by 30 cm (preparation for conveyor belt) + € 2,080 net - Eco rings: + € 1,980 net (recommended for more than 20 % hardwood) - Double row of knives + 995 € net - Special scraper + 990 € net (recommended when shredding veneer or paper, or items with a material thickness of less than 3 mm) - Articulated conveyor belt + € 8,770 net Angle: 0-60 degrees adjustable Discharge height: approx. 2000 mm - Automatic overbelt magnet + € 5,980 net Alternatively, fixed magnetic block above the conveyor belt for regular manual stripping + € 990 net (for low metal part accumulation) - Conveyor belt and overbelt magnet control + € 2,750 net (start and stop synchronized with the chipper) alternatively manual start and stop of the belts + 595 € net . Requirements for the raw material: - The moisture content (atro) must be below 30% - Installation temperature: tempered room at a minimum of +5°C - Metals and mineral impurities such as sand, stones etc. lead to increased wear

Condition: new, Year of construction: 2023, The ideal machine for shredding hardwood and softwood Another machine, available immediately (ex works Neckartailfingen) . Motor: 18.5 kW; 400 V - 50 Hz - 3 ph, Knives: 14+2 pieces, 40x40mm, multiple rotatable, Rotor diameter: 260 mm, Control: Omron SPS, Cutting unit opening 600 x 800 mm, hopper volume approx. 0.6 qbm, hydraulically operated pusher Screen perforation of your choice (12 - 40 mm) Suction nozzle Ø 160 mm Weight approx. 1,300 kg Dimensions (lxwxh) approx. 1737 x 1167 x 1650 mm . The following options are available at extra cost: - Additional row of knives + 995 € net (28 instead of 14) - Surcharge for 4-sided segment shelf + € 2,170 net Bea9Ia3L27 (prevents blocking of the pusher. Recommended for materials with a thickness of less than 3 mm) - Raise shredder by 30 cm (preparation for conveyor belt) + € 1,980 net - Angled conveyor belt (discharge height approx. 220 cm) + €8,770 net - Overbelt magnet + € 5,980 net - Conveyor belt and overbelt magnet control + € 2,750 net (start and stop synchronized with the chipper) - Special bearing +1,540 € (rarely required. Closed, even more stable rotor bearing. Possibly a consideration for sieves smaller than 15 mm or with a lot of fines. Not necessary if the bearings are lubricated with grease every approx. 2 weeks during operation) . Requirements for the raw material: - The moisture content (atro) must be below 30 % - Metals and mineral impurities such as sand, stones etc. lead to increased wear. . We will be happy to carry out a free test with your material and invite you to visit us in Neckartailfingen. It is also possible for you to send us your material by freight forwarder and we will document the test with pictures and videos.

Year of construction: 2025, Condition: as good as new (ex-display), to sell the demonstration machine at a special price Our MVZ 7.5 granulator is suitable for shredding thin-walled parts and/or for post-shredding wood chips. More details after a test with your material. Larger systems are also available as an option The price is only for the shredder as shown in picture 1 - fan, cyclone and filter are options. Motor: 7.5 kW *larger systems on request (4 to 75 kW) Throughput up to 120 kg/h *depending on screen and material Much higher throughput rates can be achieved with the secondary shredding of wood chips. Details after the test with about 30 kg. Rotor diameter: 180 mm 6 rotary knives each 225 mm 4 stationary knives each 225 mm Dimensions: 930x730x1420mm weight: 450 kg, suction nozzle: 100 mm, Screens: 6.8 and 15 mm - other screens available, Price per sieve: €390. Price set replacement knife: 579 € Nm39X Suitable e.g. fur: - Plastic waste of all Art.-No Various materials - HDPE, LDPE, PP, PS. PC, PA - biomass -Wood - Herbs etc. Parts from injection molding, blow molding, injection molding scrap, small bottles, cables, small pipes, profiles, etc

Condition: new, Year of construction: 2025, operating hours: 6 h, ready produced Our best-selling briquetting press, the classic. + Tried and tested, simple technology for extremely low susceptibility to errors + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Top price-performance ratio Options for an extra charge: * Surcharge for the level indicator that enables automatic operation + € 995 net * Surcharge for large pre-compression chamber + 980 € (recommended for light material like straw) Briquette diameter: 50 mm Front bush: 50 mm Briquette stroke max .: 40 mm Briquette lift opt ​​.: 40 mm Throughput (depending on material): 30-60 kg / h * * depending on the bulk weight * based on a bulk weight of 200 kg per cubic meter . Motor power: 5.5 kW 400 volts / 50 Hz / 3 phases Length: 1680 mm Width: 1100 mm Height: 1500 mm Weight: 680 kg Oil volume: 110 liters Silo diameter: 1000 mm Silo content: approx. 0.7 square meters Pump: 27 liters Hydraulic pre-compressor Option cooling pressing tongs: no Bst09Lehrk Hydraulic oil cooling option: yes Level monitoring option: yes CE compliant . Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 18% - Maximum chip length 15 mm - Installation temperature: temperature-controlled room at at least + 5 ° C - The customer must insure himself against loss of hydraulic oil - The loading must be free of metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear

Condition: reconditioned (used), Year of construction: 2024, Delivery time approx. 3 months . The hydraulic briquetting presses of the MPP NEM series press materials such as aluminum, copper, brass, bronze, graphite and other non-ferrous metals into dimensionally stable cylindrical briquettes. The machines are characterized by a robust design that guarantees consistent briquette quality in continuous operation. The pressing process takes place without the addition of binding agents, solely through the hydraulic pressing pressure. The volume of the starting material can be reduced by up to 90% depending on the material. Bixvstdg Throughput: up to a maximum of 70 kg/h (depending on the material), Briquette diameter: Ø 50 mm, Motor: 5.5 KW, 400 volts / 50 Hz / 3-phase, Pump: 40 liters, . Maximum briquette length: 50 mm, Optional briquette length: 40 mm, Silo diameter: 1,000 mm, Oil tank 110 liters . Dimensions: 1750x1130x1100 mm lxwxh Weight: 780 kg. . Hydraulic pre-compression via slide valve Main press cylinder Vertical cylinder . Fill level indicator: yes . Requirements for the starting material - Max. chip length: 15 mm - Installation temperature: temperate room at least +5°C - Max. weight on agitator: 200 kg. - The feed must be free of magnetic metals and mineral contaminants such as sand, stones, etc. Damage to the press tools and / or increased wear can result

Condition: new, Year of construction: 2024, Consists of a bale opener for large bales type MHB and a straw shredder type MHZ Rxqwlvgbg 1) Bale opener MHB: Special price from €22,975 net Production time approx. 15 weeks Suitable for round or square bales. Includes FU (frequency converter) - this regulates the speed of the scraper floor The bales are placed on the scraper floor and the feed of the milling machine is switched on. The tines of the milling machine tear the straw off the bale and throw it into the funnel. Ideally, the combination of bale shredder and straw shredder is recommended here Technical data for bale shredder: Performance: 1-2 bales per hour up to a maximum of 600 kg per hour (depending on the sieve size used in the straw mill, kW number of the straw mill. Without a straw mill, the bale shredder can even shred up to a maximum of 900 kg / h of straw) Max. size of square bales 2400x1200x800 mm lxbxh Motor milling machine 5.5 KW 380 Volt Scraper floor feed 0.75 KW 380 Volt Dimensions 3750x1730x2460 mm lxbxh Weight 400 KG 2) Straw shredder MHZ 600 - 11/15 kW; immediately available Special price from €6,995 net Special funnel: + €970 (only in conjunction with bale shredder) Surcharge for the even larger straw shredder (18.5 kW) + €2,940 net Technical data, MHZ with special funnel: Motor 15 KW 380 volt electric motor Diameter: 600 mm Hardened cutting blades Sieve with interchangeable inserts Optional 10, 12,15,22,30,45 mm holes With star-delta switch Ue protection and 8 m supply line, ready to plug in Blow-out nozzle 160 mm Blow width approx. 12 m Dimensions approx. 1600 x 1020 x 1360 mm lxwxh Weight approx. 240 KG --- Options against Surcharge: Intake screw + €970 net Cyclone (mounted on site by customer) *should be located a maximum of 10 m away + €2,970 net Simple filter €997.50 net --- Other options: Industrial extraction system (demonstration) + from €9,990 net Optional with rotary valve *depressurizes the material + €4,750 net Control: from €975 net Special 3 m shredder extension *other dimensions would have to be calculated + €7,995 net Briquetting press MPP 180 S; little used demonstrator 70 mm briquette - up to a maximum of 100 kg / h from € 39,700 net * larger machines on request --- Description: muetek bale opener was developed for opening round and square bales of hay and straw. The shredder flanged to the bale opener shreds straw from all types of grain, hay, corn and miscanthus. The muetek machines in the MHZ / MHB series are characterized by a robust design and solid construction. muetek bale openers in the MHB series are equipped with a chain conveyor onto which the straw bale is placed with the front loader. The support is adjustable depending on the type of bale. The chain conveyor presses the bale against the milling rotor, the feed speed is adjustable. The milling rotor is fitted with several teeth that tear open the straw bale. The straw separated from the bale is ejected. Sieves 10-60 mm --- Basically, the machines work for dry raw materials: - Straw - Hay --- The dissolution of hemp only works with a special dissolution machine Surcharge approx. €9,700 net * depending on the model. The shredding of hemp does not work with the straw mill. *If at all on a cutting mill

Condition: as good as new (ex-display), Year of construction: 2023, Special price for trade fair machine Combination of: mütek briquetting press MPP 60 + suction unit MMJET 350 *Approved for indoor installation *Both individual machines ready produced and in stock, they only need to be connected to each other 1. technical data briquetting press: Our best-selling briquetting press, the classic. + Tried and tested, simple technology, for extremely low susceptibility to faults + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Top price-performance ratio Product code: 84793010 Briquette diameter: 50 mm Front bush: 50 mm Briquette stroke max.: 40 mm Briquette stroke opt.: 40 mm Throughput capacity (depending on material): up to 60 kg/h* *Depending on the bulk density *based on a bulk weight of 200 kg per cubic meter . Motor power: 5.5 kW, 400 Volt / 50 Hz / 3-phase, Total system footprint: 2.2x1.1x 2.8 m LxWxH Height - 2.8 m (special container) Delivery also possible in 2 components Weight: approx. 1200 kg, Oil volume: 110 liters Silo diameter: 1000 mm Pump: 27 liters Hydraulic pre-compressor Option cooling press tongs: no Hydraulic oil cooling option: yes Fill level monitoring option: yes CE compliant 2. technical data clean air extraction unit MMJET 350: Suction connection diameter: 350 mm Motor: 11 kW Suction connection on the left (when standing in front of the dust garbage can) Residual dust content: ᐸ0.1 mg/m³ Max. volume flow: 8000 m³/h Nominal volume flow (20 m/s): 6950 m³/h Filter area: 71 m² Negative pressure: 2630 Pa Automatic filter cleaning B3T3Gvt Cartridge filter JET cleaning system Powder fire extinguisher installed (tested every 2 years by specialist company) Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 18 % - Compressed air on site - Maximum chip length 15 mm - Installation temperature: temperature-controlled room at a minimum of +5°C - The press must be selected large enough by the customer so that it removes more material than is sucked in at the peaks - The feed must be free of metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and/or increased wear.

Condition: new, Year of construction: 2023, Demonstrator with 15 operating hours Another machine, available immediately (ex works Neckartailfingen) Shredder MRZ 830 Product code: 84659600 Feed opening 800x1000 mm Motor: 18.5/ 22 kW; 400 V - 50 Hz - 3 ph Knives: multiple rotating Hydraulically operated pusher Screen perforation of your choice (10 - 40 mm) Suction nozzle Ø 200 mm Weight approx. 1,600 KG Dimensions (lxwxh) approx. 2290 x 1420 x 1750 mm Turbo coupling Included as standard: - Automatic star/delta start - fast hydraulics - auto. OFF when the rotor is idling - Speed 70-90 rpm for high throughput capacity - Cycle control to avoid idling times - Performance-enhancing step control of the hydraulic slider - Pertinax guides for hydraulic slide - Vibration-damping machine feet - CE compliant . The shredder is designed for shredding untreated wood, chipboard and MDF and other materials after testing and approval by the manufacturer. . Other shredder options: - Raise shredder by 30 cm (preparation for conveyor belt) + € 2,140 net - Folding conveyor belt + 8.770 € net Horizontal part: 1200 mm Rising part: 2500 mm Angle: 0-60 degrees adjustable Discharge height: approx. 2000 mm + - 100 mm - Overbelt magnet + 5.980 € net - Conveyor belt and overbelt magnet control + € 2,750 net (start and stop synchronized with the chipper) . Bdqriiu289 Requirements for the raw material: - The moisture content (atro) must be below 30 %, - Installation temperature: tempered room at a minimum of +5°C - Metals and mineral impurities such as sand, stones, etc. lead to increased wear

Condition: new, Year of construction: 2023, Ideal for shredding straw, polystyrene, leaves, hay and bread. Throughput depends heavily on the sieve and source material: - up to a maximum of 350 kg / h for straw with a 15 mm sieve - up to 60 kg / h for EPS with a 15 mm sieve Motor 11 KW - 400 volts, Ucbu22Bv (9.2 kW or 15 kW also possible upon request) Optional: *Surcharge for the next larger machine with 18.5 kW and larger silo diameter + 1,995 € net stable steel construction, hardened cutting blades, sieve with interchangeable inserts, optional (10), 15, 22, 26, 30, 40, or 60 mm perforation with electric drive with star-delta switch Ue protection and 8 m supply line ready to plug in, blow-out nozzle 150 mm, optional for plastic or Grain pipes, Blowing width approx. 12 m, Chassis with 2 wheels Ø 380 mm, and a swiveling support wheel Ø 125 mm, all wheels with solid rubber tires, Dimensions approx. 1200 x 900 x 1270/1400 mm lxwxh Weight approx. 240 KG, Spare parts prices and options: 24 blades, hardened €9.90 each net 6 bolts €14.90 each net 1 sieve €475 each net Cover €290 each net Styrofoam disc: €600 each net

Condition: new, Year of construction: 2023, one machine ready produced Your advantages: + extremely large cutting unit opening with 1300x1200mm + special rotor suitable for hardwood and softwood + Energy-efficient and powerful with 37 kW at start-up Technical specifications: Feed opening (mm): 1,300 x 1,200 Hopper capacity (cbm): 1.6 m³ Rotor diameter (mm): 368 Rotor speed (rpm): 65 - 125 Power requirement (kW): 37 Screen perforation (mm): 30 - 50 mm - selectable Tools: 37/70 knives Extraction nozzle Ø (mm): 200 mm Dimensions: 2430x2410x1735 mm (lxwxh) Weight (approx. Kg): 3,920 Optional for a surcharge: * to shred veneer or paper (anything thinner than 3 mm) - we recommend a segment floor. The machine in preproduction has not yet installed this. Special option at an additional cost. - 2nd row of knives, for up to 30% more throughput - Fast hydraulics, for increased throughput - Preparation for conveyor belt removal - conveyor belt - HAWK-EYE overbelt magnet --- Optimal pallet size with the option slide extension = 1200x1400 (option slide extension, the cutting unit opening 1300x1700 surcharge + 12,975.00) * is associated with significantly longer production time. * larger machines on request --- Requirements for the raw material: - The moisture content (atro) must be below 30% - The loading must be free of metals and mineral impurities. This can result in damage to the tools and / or increased wear Bqb3Du8Xao

Condition: as good as new (ex-display), Year of construction: 2024, Production time appr. 4 months Our best-selling briquetting press series + Tried and tested, simple technology for extremely low susceptibility to errors + 25 years of experience, further development and know-how + Several hundred machines in use with satisfied customers + Good price performance ratio Throughput approx. Up to 200 kg per hour * strongly dependent on the material. - in the last test with aluminum granules smaller than 5 mm - approx. 186 kg per hour + the pressed emulsion. - in the last test with aluminum chips smaller than 18 mm - approx. 120 kg per hour + the pressed emulsion. Technical specifications: Motor: 7.5 KW + 0,55 kW Cooler 400 volts / 50 Hz / 3-phase, Front bush: 125 mm, U9Ud82Upt Briquette stroke max .: 100 mm, Briquette stroke opt .: 80 mm, Pump: 80 liters, Storage container approx. 0.5 qbm content (expandable), Diameter: 1200 mm, with agitator discharge, Hydraulic unit complete with oil tank 220 liters Dimensions approx. 2095 x 1600 x 1310 mm lxwxh, Weight 1370 kg, Automatic on-off switching via level indicator CE compliant. . Requirements for the raw material: - Chip length maximum 20 mm - Installation temperature: temperature-controlled room at at least + 5 ° C - The loading must be free of magnetic metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear

Year of construction: 2024, Condition: new, Overview - of the different variants *Not every position is required: Optional: -Bale shredder MHB from 24.990 € net -MHZ straw mill from € 7,980 net -Special hopper 970 € net -Cyclone from € 3,750 net -Sheet metal silo demonstrator with discharge (only sketched in the picture) *optional, if you want to load with the wheel loader Unit price net from € 14,750 - Demonstrator -Dedusting auger - length approx. 4 m 4 sieves are mounted on the underside, which are extracted. Unit price net from: 9.750 € - Extraction parts / hoses flat rate 945 € net - Complete control system Net unit price: € 2,750 -Demonstrator extraction unit MMJET 160 Demonstrator, with cleaning Connection 160, fan 2,2kw air capacity 1850m³ /400 V Automatic compressed air cleaning Unit price net from: 6.950 € -Baler B 400 Bales approx. 400x400x800 (height adjustable) Up to 30 bales per hour with + - 20 kg from 59.995 € net *A reference system (baler) is located in zip code: 64579 Gernsheim Technical data: Bale size (WxDxH): 400 x 400 x 800 (height can be adjusted on request) Bale weight +/- 20 KG (depending on material) Capacity: approx. 30 bales per hour Storage container approx. 0.7m³ capacity Filling level sensors for min./max. filling level in the container Hydraulic pre-compressor Hydraulic compression ram Hydraulic unit, valve block with oil tank Pump 18.5 KW / 50 liters Rollers in the bale chamber for easy bale push-off Dimensions (l x w x h) 3105x2830x2455 mm Weight approx. 1500 KG mütek baling presses / wrapping machines are designed for the production of bales from a wide variety of materials such as shredded micanthus or elephant grass, wood chips, sawdust and shredded straw. straw. The machine is characterized by a robust design that guarantees consistent quality in continuous operation. quality in continuous operation. The baler compacts the material filled into the storage container without the addition of binding agents and packs the material into plastic bags. The volume of the material can be considerably with the baling press. The volume reduction rate depends on the material. The maximum material moisture content must not exceed 18 % Atro. The container of the mütek baler can be fed automatically or manually and has a volume of approx. 0.7 m³. volume of approx. 0.7 m³. Containers with a larger volume or with an attached suction and filter system as a complete disposal unit are also available. In addition to automatic filling via deduster, mütek also offers filling by means of screw conveyors. With both variants, automatic automatic dedusting is possible. mütek baling presses are equipped with a control cabinet for the control system. In the standard version, the dimensions of the bales (width x depth x height) are 400 x 400 x 800 mm. However, the height can be adapted to your requirements on request. The following advantages arise in the production of bales: - simple and safe storage - No loose dust - Minimization of the storage volume - Low transport volume *Requirements for source material: - dry (max. 30 % ATRO) - Maximum length 35 mm Nwcvh

Condition: as good as new (ex-display), Year of construction: 2023, Ideal for shredding polystyrene or similar materials Throughput depends heavily on the sieve and source material: - up to 60 kg / h for EPS with a 15 mm sieve *the coarser the sieve, the higher the throughput Motor 9.2 / 11 KW - 400 volts, stable steel construction, hardened cutting blades, sieve with interchangeable inserts, optionally (8), (10), 15, 22, 26, 30, 40, or 60 mm perforation with electric drive with star-delta switch Ue protection and 8 m supply line ready to plug in, Ccdlqcpak9 blow-out nozzle 150 mm, optionally for plastic or grain pipes, blow width approx. 12 m, chassis with 2 running wheels Ø 380 mm, and a swiveling support wheel Ø 125 mm, all Wheels with solid rubber tires, Dimensions approx. 1200 x 900 x 1270/1400 mm lxwxh Weight approx. 240 KG, Spare parts prices and options: 24 blades, hardened €9.90 each net 6 bolts €14.90 each net 1 sieve €475 each net Lid €290 each net

Condition: new, Year of construction: 2025, Briquetting press NEM 900: production time appr. 5 months for briquetting aluminum chips Throughput: up to maximum 320 kg / h Bq9Ixnblmu * more details after a free test with heard material . Briquette diameter: Ø 70 mm Optimal briquette length: 70 mm . Technical specifications: Total connection: approx. 31 kW In continuous operation approx. 22 kW 400 volts / 50 Hz / 3 phases Pump: 120 + 60 liters per minute Silo: 1 m³ Silo rollers: 1200 mm Including agitator Oil tank: 600 liters Dimensions: 2500 x 1700 x 1730 mm lxwxh Weight: 2250 kg. Hydraulic pre-compression via slide Main press cylinder Vertical cylinder Above for connecting a cooling unit . One and the source material - max.span: 18 mm - Excessive temperature: temperate room at at least + 5 ° C. - max.weight on agitator: 200kg. - The loading must be free of metals and mineral impurities such as sand, stones, etc. This on the pressing tools and / or responsible wear can result