Plasma cutting machine

MicroStep MG 6001 20Prb + CH800P+HyperTerm HPR260

Condition: new, functionality: fully functional, Year of construction: 2026, roller (bottom) diameter: 310 mm, roller (top) diameter: 320 mm, roller diameter: 310 mm, roller length: 1,550 mm, working width: 1,500 mm, sheet thickness steel (max.): 38 mm, overall weight: 12,500 kg, total length: 4,500 mm, total width: 2,300 mm, total height: 1,740 mm, power: 18.39 kW (25.00 HP), working length: 1,500 mm, Equipment: documentation/manual, emergency stop, FACCIN HAV 15342 variable three-roll bending machine Electronically controlled, hydraulic three-roll bending machine Technical data: Number of rollers: Three Geometry of the side rollers: variable Working width: 1550 mm Top roller diameter: 320 mm Side roller diameter: 310 mm Pressure force against the top roller: 160 tons Working pressure at nominal force: 250 bar Guaranteed installed power: 18 kW (25 hp) Guaranteed maximum rotation speed: 3.5-7 m/min Guaranteed machine weight: 12,500 kg Length: 4,500 mm Width: 2,300 mm Height: 1,700 mm Guaranteed performance: for material with yield strength 260 N/mm² Rolling capacity (full working width) 38 mm Bending capacity (full working width) 20 mm from pipe diameter 1,600 mm Rolling capacity (full working width) 30 mm Bending capacity (full working width) 17 mm from pipe diameter 415 mm Standard equipment: Ljdpfx Aot Akt Rjlcohk Variable geometry with linear guides for roller movement Extra long folding bearing for increased frame stability Electronic parallelism system EPS Hardened rollers for high wear protection All rollers ground after heat treatment Siemens S7-HMI PLC control system PGS-CLASSIC control system with Siemens touch panel Hitech hydraulic and electrical package Simultaneous rotation and roller movement Safety ripcord with emergency stop and CE certification Central lubrication Water cooling for the hydraulics Cone bending device Prepared for retrofitting of supports and roller conveyors FACCIN Advantage Package AP

Condition: good (used), Rolling pressure 220 kN Ø Pieces 3mm min; 70mm max Pitch 6mm max Grooving pitch 2.25mm max Roller width 160mm max Ø Roller 133mm min; 170mm max Roller shaft speed 24 30 38 45 62 72 90 114 rpm Ø Roller carrier shaft 54mm standard; 69.85 special Distance between shafts 135mm min; 230mm max Working stroke 15min max Feed rate 0.5mm/s to 6mm/s Laminating time 0.1s to 100s Pause time 0.1s to 100s Main motor 5.5 Kw Ljdpfx Ajvyyyxelcjhk Electrical power consumption 8.6 Kw Tank capacity 130 L Weight approx 2100 Kg

Condition: good (used), Year of construction: 1954, Ref. -No.: 10576 Manufacturer: VDF WOHLENBERG Type: VDF Year of construction: 1954 Type of control: Konventionell Control: n/a Storage location: Halberstadt Country of origin: Germany Machine-No.: 27XXX Turning Length: 4000 mm Lhjdpsxmd U Ajfx Alcsk Spindle Diameter: Ø 80 mm Faceplate Speeds I: 355 RPM Turning diameter over cross slide: Ø 1000 mm Max. Turning diameter: Ø 1250 mm

Year of construction: 2014, condition: ready for operation (used), A complete CNC double gantry plasma cutting system Microstep with oxyfuel torch for nesting, bevel cutting and tube processing is available. 1) Plasma cutting system, max. processing length: 16500mm, max. processing width: 2500mm, max. processing width including shaft: 3700mm, max. material thickness VA/structural steel: 20mm/40mm, number of gantries: 2. Gantry 1: with a plasma rotator and a Kjellberg HiFocus 280i neo plasma cutting source. Gantry 2: fully automatic oxy-acetylene torch for possible equipment of a second torch carriage. Pipe cutting device: pipe diameter range: 30mm-700mm, max. pipe length: 16500mm, operating hours: approx. 15000h. 2) Filter system Donaldson Cyclopeel DFPRO 16, volume flow: 16000m³/h, filter elements: 16. Documentation available. On-site inspection is possible. Expected to be available from the end of 2025/beginning of 2026. Pictures are from commissioning in 2014. Ledpfx Alowmqwyscehk

Condition: used, Technical details: cutting thickness max.: 0,5 - 70 mm infeed - automatically: 40 mm control: CNC 2050 table-size: 2x L:1500 x B: 1700 x H: 720 mm burner heads: 2 Stück weight of the machine ca.: 6,7 t Autogenous flame cutting machine with table. With corresponding additional equipment, the following processes can be performed: Plasma cutting; Plasma signing; Marking; Graining; Boring. Lodpfxju Nwfuj Alcehk other specifications: 2x tables: -L:1500 x W: 1700 x H: 720mm, supporting surface L: 1500 x W: 1500mm; with suction connection Ø 320 x 60mm Distance control system: -Make ZAC 2100, type 7211-2-100 V02; -size 105 x 165 x 130mm -24 VDC; torch voltage 30 - 300V; protection class IP50 -ignition height 1 - 25mm in steps of 0,2mm -cutting height 1 - 12,5mm in steps of 0,25mm -Cutting height together 0 - 20mm in steps of 0,5mm Height drive: - Linear Drive model, type 2203; 24 VDC 100 - 190 watts; stroke 220mm. Laser generator: -manufacturer Kijellberg, type HiFocus 280i, welding rectifier -Power range 10A / 84V - 280A / 192V; protection voltage IP22; cooling type AF; with 2x cooling connection 1/2". Heat exchanger: -manufacturer Kijellberg, type KWE 360 -working voltage U1 400V / 2,5A; protection type IP22; coolant of Kijellberg mixture; with 2x cooling connection 1/2". *

Condition: excellent (used), Numerical Control Power Control + Software Cadmatic 4 Professional No. 1 Infeed roller tracks (ca.) 32,000 mm Lifting table (mm) 5600 x 2200 VAC loader (sliding bridge) with fan suction for loading special or delicate panels 1° Rear-pusher, with No. 6 clamps/grippers Turning device (rotating unit) at 90° 1° Panel Saw - Max cutting width mm 5600 (cutting line with air cushion) Max blade projection (mm) 190 Scoring Unit (max. diameter saw / power) mm 200 (Kw 2,2) Main Sawing Unit (max. diameter saw / power) mm 600 ( Kw 36) Lsdovnq H Eopfx Alcshk Adjustable speed of the saw carriage (QS) (m/min) 1 - 130 m/min 2° Rear-pusher, with No. 14 clamps/grippers 2° Panel Saw - Max cutting width mm 2200 (cutting line with air cushion) Max blade projection (mm) 190 Scoring Unit (max. diameter saw / power) mm 200 (Kw 2,2) Main Sawing Unit (max. diameter saw / power) mm 600 (Kw 36) Adjustable speed of the saw carriage (QS) (m/min) 1 - 130 m/min Waste evacuation system with grinder (Kw 19.5) No. 2 Front supporting tables with Air blowing system (mm 800 x 2160) Plastic wheels coated with special material to avoid scratching delicate panels Automatic unloading System of the cut panels: N° 2 x Liftomat HAU-A 25/12 Automatic Stacking System with 8 stations

Condition: used, Year of construction: 2020, functionality: fully functional, table length: 6,000 mm, table width: 2,540 mm, sheet thickness steel (max.): 50 mm, cutting length (max.): 6,000 mm, cutting width (max.): 2,540 mm, FICEP KRONOS KR25SP - CNC GANTRY PLASMA CUTTING SYSTEM FOR STEEL PLATES | YEAR 2020 Lodpfx Asv Iaqyolcehk The Ficep Kronos KR25SP is an automatic CNC gantry system for high-definition plasma cutting of steel plates, designed for steel construction and sheet metal fabrication shops that need precise, repeatable and cost-efficient parts directly from plate. With a maximum plate size of 2,540 x 6,000 mm and a plasma cutting thickness of up to 50 mm, it covers a broad range of parts in a single pass. CONDITION & REFURBISHMENT Refurbished and inspected by a certified technician, ready for operation. The machine is fully functional and can be put into production immediately. - The exact scope of reconditioning varies from machine to machine and is disclosed individually upon serious interest. - Viewing possible by arrangement (machine reconditioned - no demonstration under power). FUNCTION & APPLICATION The KR25SP cuts steel plates fully automatically according to CNC program in gantry design. Using Hypertherm plasma technology including True-Hole technology, it produces contour-accurate cut parts and hole patterns at high cut quality - ideal for gusset plates, end plates, base plates and connection components in steel construction. The robust grid cutting table is prepared for connection to an extraction system; a network remote-diagnosis interface supports maintenance and support. TECHNICAL DATA - Manufacturer: Ficep S.p.A., Italy | Model: Kronos KR25SP (KRONOS SP series) - Machine type: Automatic CNC gantry plasma cutting system for steel plates - Year of manufacture: 2020 | Serial number: 36499 - Condition: used, refurbished by certified technician - Maximum plate size (W x L): 2,540 x 6,000 mm - Max. plasma cutting thickness: 50 mm - Plasma straight-cut torch: 1 | Plasma unit: Hypertherm XPR300 - Hypertherm True-Hole technology: available - CNC control and drives: Fanuc (to be confirmed on the machine during inspection) - Remote diagnostics: available (network connection) - Cutting table: robust grid construction, prepared for extraction system - Extraction and filter system: optionally available Further details (machine weight, connected load, footprint, cutting speed) are available on request. SCOPE OF DELIVERY - 1 x Ficep Kronos KR25SP gantry system (year 2020) - 1 x plasma straight-cut torch (Hypertherm XPR300) - Grid cutting table with extraction preparation - CNC control and drives - Remote-diagnosis interface (network) LOGISTICS & LOCATION Location: Ulft (Netherlands), directly at the German border - short transport distance from the entire DACH region. Dismantling, transport, installation and commissioning by ASM by arrangement - individually calculated upon request. ABOUT ASM Arendsen Steel Machinery (ASM) is your specialist for refurbished Ficep steel construction machinery. We supply inspected, ready-to-operate systems for steel construction and sheet metal fabrication. Further Ficep systems on request. CONTACT / INQUIRY Arrange a viewing | Price on request | Request a callback. Sale exclusively to commercial customers (B2B).

Condition: excellent (used), Year of construction: 2005, Year of manufacture: 2005 Mounting: Ceiling Ceiling guide length: approx. 15 meters Availability: 2 units Lhsdpfx Aowvi Upelcjk Load capacity: Manipulator 1 – 30 kg Manipulator 2 – 35 kg Number of axes: 4 Gripper: Pneumatic parts gripper (per manipulator) For suspension on the rail

Condition: used, Year of construction: 1965, turning diameter over bed 1000 mm turning diameter over slide rest 760 mm turning length 5000 mm spindle bore 82 mm turning speeds 3,55-710 U/min faceplate 1000 mm 3-jaw chuck 500 mm steady 2 Ledpsyqulujfx Alcohk total power requirement 22 kW weight of the machine ca. 10 t dimensions of the machine ca. 8x2x1,8 m Multifix steel holder with inserts The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: used, Technical details: turning diameter over bed: 1200 mm turning diameter over support: 800 mm turning length: 3200 mm length of gap: 600 mm center height measured in bed: 600 mm Lhsdpfxszuyfas Alcjk turning dia. in gap: 600 mm spindle turning speed - continuous: 4,6-545 / 22 steps U/min spindle passage: 90 mm feed: 1,4-510 m/min taper: MK6 total power requirement: 15 kW weight of the machine ca.: 10,0 t dimensions L x W x H: 6,20x2,00x1,80 m dimensions electric cabinet LxWxH: 0,55x0,33x1,0 m equipped with: face chuck diameter 1000m (4 jaw chuck) fourfold chisel taper steady rest closed, inside diameter 250mm revolving tail center conical turning device *