Gear shaper

LORENZ LS 1.000

Condition: good (used), Year of construction: 2000, gear diameter: 449 mm, Equipped with: Fanuc 150MB CNC Control Dry Cutting Cutter Shroud Chip Evacuation System Auto Doors Hydraulic System Lubrication System Work light Stack Light Specifications: Largest Speed Ratio: 10:01 Work Area (Continuous): Largest Depth of Teeth: 15.24 mm Largest Width of Tooth Face: 50.8 mm Work Area Axis: Horizontal Movement X Axis: -114 - 178 mm Vertical Movement Y Axis: -178 - 190 mm Movement of the Carriage Baseplate Z-Axis: -10.16 - 500 mm Workpiece Headstock Swiveling Range B-Axis: -3 - 90 Degree Maximum Distance Machine Center to Spindle Side: 165 mm Number of Teeth: 5-200 Inclusive Max. Gear Pitch Dia. of Typical 35 Deg. Spiral Angle Gear Using Max. Cutter Dia. 12" Cutter at the Following Ratios: Face Milling 1 x 1 - 13.5" - 342.9mm 2 x 1 - 16.0" - 406.4mm 5 x 1 - 17.7" - 450.0mm Face Hobbing (210mm Dia. Cutter) 1 x 1 - 10.560" - 268.22mm 2 x 1 - 10.286" - 275.00mm 5 x 1 - 11.810" - 300.00mm Milling Head Diameter: Helixact: 100,125,169,200,250,320mm Continuous Gumption Procedure, Teichloroethylene: 102 - 210 mm Workpiece Spindle: Drilling of Large Diameters: 5 3/64" Cone Upward Gradient on 304.8 mm (1 Foot): 21/32" Deep One of the Cone: 5.29" Diameter of the Whole Spindle Perforating: 3.35" Speeds: B-Axle Workpiece Headstock Drag Axis: 30 Degrees A-Axle Workpiece Spindle Number of Revolutions: 0 83 min-1 Nodpjruakgsfx Aphjdb X-Axis Horizontal: 80 mm/sec Y-Axis Vertically: 80 mm/sec Z-Axis Carriage Baseplate: 80 mm/sec Space Requirement L x W x H (Approximate): 4.75 x 3.40 x 2.54m / 188" x 134" x 100" Machine Weight (Approximate): 10980 kg / 24,156#

Condition: used, Year of construction: 2004, functionality: fully functional, CNC gear hobbing machine Control: Siemens 840 D Power Line Technical data: Max. workpiece diameter: 150 mm Table diameter: 145 mm Max. table speed: 800 rpm Distance between centers: 10 – 200 mm Max. axial travel: 250 mm Swivel angle of milling head: +/- 45° Max. tailstock travel: 300 mm Max. rapid traverse rate: 17,000 mm/min Drive power of milling head: 19 kW Max. module: 3 mm Max. speed of milling spindle / tool speed: 4,500 rpm Max. diameter of hobbing cutter: 80 mm Max. length of hobbing cutter: 200 mm Dimensions approx.: 5.5 x 3.7 x 3.1 m Weight approx.: 9,500 kg Equipment: Chip conveyor Oil mist extraction / oil extraction Oil cooler Ndodozkwvnepfx Apheb Steady rest with lowering device and vertical adjustment Rotary ring loader with two workpiece grippers Loading belt system for automatic feeding 5 milling arbors / hobbing cutter holders: 1 x Ø 22 mm 2 x Ø 27 mm 1 x Ø 32 mm 1 x Ø 40 mm Other: Video recordings via WhatsApp

Condition: used, Year of construction: 2007, x-travel 900 mm y-travel 300 mm z-travel 1000 mm control Siemens Sinumerik 840D max. workpiece diameter 1600 mm max. module 20 mm tip circle diameter 350 mm Milling arbour diameter 375 mm Total closing value 80 kVa weight of the machine ca. 33,5 t dimensions of the machine ca. 10,530 x 6,375 x 4,680 m Feed rate: - X-axis 1 to 3000 mm/min - Y-axis 1 to 3000 mm/min - Z-axis 1 to 4000 mm/min Spindle speeds in rpm: Njdpfew Rrb Hex Aphedb - Tool 26 to 265 - Workpiece table 0 to 8 Equipment/accessories: - M 2 motor milling head - Milling mandrels - Oil cooler - Technical documentation

Condition: good (used), Year of construction: 2000, functionality: fully functional, machine/vehicle number: 018.0179.90.035, (Please tell us your offer price) Sale only within Europe, incl. Turkey Price without packaging; delivery condition: FCA (machine location) ===== Technical data see handout. All warranty rights are excluded. For the correctness of the technical data and year of construction, for the completeness of accessories and tool equipment, and for compliance with all safety and environmental protection requirements specified in the accident prevention regulations. No sale to private individuals. Sales only within Europe, incl. Turkey Price without packaging; Delivery condition: FCA (machine location) ===== Technical data please see handout in attachment. German text leading language. Without any guaranty and warranty, including completeness of tools & accessories as well as environmental and safety regulations. Nodpfjyh R Uwox Aphedb No private sales.

Condition: used, Year of construction: 2006, Technical details: max. wheel diameter: 300 mm max. module: 7 weight of the machine ca.: 15 t table turning speeds: 100 U/min table diameter: 180 mm hob turning speeds: 750 U/min max. hob diameter: 300 cutter length max.: 230 mm Liebherr LC300 with loading automation Machine including counter holder Ndedsyz Sd Ropfx Apheb The machine used to work with emulsion *

Condition: good (used), Year of construction: 1984, max. wheel diameter 250 mm gear width 275 mm max. module 6 weight of the machine ca. 5,5 t The gear hobbing machine ZFWZ 250 is suitable for the economical production of all hob-processable cylindrical gear types, such a: - spur and helical gear, wormgears and worms, splined shafts, keyed shafts, serrated profiles, chain wheels and ratchet wheels,as well as conical and crowned spur and helical gears. Nodsv T Nqaopfx Aphedb Interchangeable wheels and milling accessories Technical data: - Workpiece diameter (max): 250 mm - Module (max): 6 mm - Axial feed travel (max): 275 mm - Tangential feed travel (max): 100 mm - Tooth helix angle (max): 45 degrees - Milling cutter diameter (max): 145 mm - Milling cutter length (max): 170 mm - Table clamping surface (min): 195 mm - Table clamping surface (max): 470 mm Power Milling cutter speeds - Stepped in 2 ranges: 56 ... 250 rpm - (Standard version): 90 ... 400 rpm - Infinitely variable in 2 ranges: 63 ... 180 rpm - (special version DC motor): 140 ... 400 rpm Weights - Machine net: approx. 5000 kg - Electrical cabinet: approx. 800 kg - Hydraulic unit + coolant tank + chip transport: approx. 700 kg Overall dimensions (with oil mist filter) - Length: Standard version: 3950 mm DC drive: 3450 mm (or 3350 mm according to table) - Width: 3300 mm - Height: Machine: 1980 mm Machine with DC drive: 2150 mm Electrical cabinet: 2200 mm

Condition: good (used), Manufacturer: STANKO Type: 7D430 Year of manufacture: 1994 Njdpfxjwpud Ao Aphsdb Table rotation 360° Head tilting possible up to 10° Big cabinet with slotting key way tools Lubrication Completely overhauled in 1994 Specifications Metric US Standard Table diameter Ø 630 mm Table load 1000 Ram displacement 320 mm X - Axis 650 mm Y - Axis 510 mm Outreach 500 mm Number of strokes 3 - 38 m/min min. Power 12 kW Dimensions (estimated) Length 3000 mm Width 2200 mm Height 3000 mm Weight 6150 kg Please note: The information on this page was provided to the best of our knowledge and ability by us, and, where possible, obtained from the manufacturer. The information is given in good faith, but accuracy cannot be guaranteed. Accordingly, they do not constitute representation and contractual terms. We recommend that you verify all important details.

Condition: used, Year of construction: 2002, turning diameter max. 420 mm turning length 1250 mm control INDEX, C 200-4 D swing diameter 630 mm travel x1 320 mm travel z1 1250 mm travel x2 170 mm travel z2 1250 mm travel x3 320 mm travel z3 1250 mm main spindle speed max. 3000 U/min main spindle drive 53 kW spindle passage 102 mm spindle head DIN 55026 Gr. 11 max. torque on the spindle 675 Nm sub spindle - spindle speed range max. 3000 U/min sub spindle drive 53 kW sub spindle - spindle passage 102 sub spindle - spindle head DIN 55026 Gr. 11 sub spindle - spindle torque 675 Nm travel sub spindle 1250 mm feed power X1 14000/Z1 14000 N Ndsdpfx Aet U R Hzjphsb rapid traverse X1 20/Z1 40 m/min feed power X2 8600/Z2 14000 N rapid traverse X2 20/Z2 40 m/min feed power X3 14000/Z3 14000 N rapid traverse X3 20/Z3 40 m/min numbers of turret head positions Rev. 1 = 12 numbers of turret head positions Rev. 2 = 10 numbers of turret head positions Rev. 3 = 12 number of driven tool stations 12 / 10 / 12 speed of driven tools max. 6000 U/min max. torque 36 / 21 / 36 Nm tool taper DIN 69880 tool taper ø 40 x 63 mm total power requirement 120 kW weight of the machine ca. 19 t dimensions of machine L x W x H 5,77 x 2,47 x 2,62 m Accessories: segment bushing chuck HAINBUCH on main spindle, collet chuck HAINBUCH, SPANNTOP SP on sub spindle, various tool holders (also for driven tools), chip conveyor, coolant - all 3 turrets are prepared for coolant through spindle, but the highpressure coolant pump and tank are not with the machine -

Condition: new, Year of construction: 2025, operating hours: 60 h, functionality: fully functional, workpiece weight (max.): 40,000 kg, wheel width: 3,700 mm, feed length X-axis: 2,000 mm, feed length Y-axis: 1,300 mm, feed length Z-axis: 500 mm, rotary table diameter: 3,700 mm, position of the milling head: 0,025, table diameter: 2,000 mm, feed rate X-axis: 10 m/min, feed rate Y-axis: 10 m/min, feed rate Z-axis: 6 m/min, total length: 12,000 mm, gear diameter: 400 mm, total height: 5,000 mm, total width: 4,000 mm, Equipment: CE marking, documentation/manual, rotational speed infinitely variable, TECHNICAL REQUIREMENTS GEAR HOBBING MACHINE GHM 2500 CNC Description of the main components of the GHM 2500 machine The GHM 2500 CNC gearing milling machine is a machine tool intended for processing by milling toothed wheels and toothed crowns. The machine is equipped with an external teeth milling head - which can process the teeth with an inclination angle from 0 to +/- 45 degrees - and an internal teeth milling head. The machine is composed of a milling unit, a unit for clamping and rotating the workpiece and the pinion axis centering tip. The milling/gearing unit is provided with three translation axes and two rotation axes, as follows: -X axis: longitudinal/radial movement towards the workpiece axis -Y axis: vertical movement of the gearing head -Aza Z: tangential movement of the gearing head -Axis: inclination +/-45 degrees of the gearing head -Axis C: rotation of the main axis of the gearing head The part fixing unit (the machine plate) has a rotation axis, axis B, for rotating the part. 1. External Gearing head – the housing of the tooth milling head is a GG300 gray cast iron cast piece. On the front side there are the counter guides of the Y axis (vertical movement of the head). Inside are the main tool actuation mechanisms, the mechanism for the horizontal movement of the gearing head axis and the mechanism for tilting the gearing head. Ndodpfey A Nglsx Aphjb The main actuation mechanism of the gearing shaft is composed of a 55 kW – S1 motor, a ZF angular reducer and a gearing shaft, mounted in the housing of the toothing horse. 2. Internal Gearing head – the housing of the tooth milling head is a GG300 gray cast iron cast piece. On the front side there are the counter guides of the Y axis (vertical movement of the head). Inside are the main tool actuation mechanisms, the mechanism for the horizontal movement of the gearing head axis and the mechanism for tilting the gearing head. The main actuation mechanism of the gearing shaft is composed of a 55 kW – S1 motor, a ZF angular reducer and a gearing shaft, mounted in the housing of the toothing horse. 3. The Quill - has the role of fixing the high parts, having a vertical displacement stroke. 4. The longitudinal advance mechanism of the upright, X axis – is made by a servo motor 30 Nm_ 3000 rpm, a Gressner worm reducer and a ball screw diam. 80 x 10, accuracy class IT 3. 5. The vertical advance mechanism of the toothing head, Y axis – consisting of a 30 Nm_ 3000 rpm servo motor, a Gressner worm reducer and a ball screw diam 80 x 10, precision class IT3. 6. Plate advance mechanism / plate rotation, C axis – is made with two 50 Nm_ 2000 rpm servo motor, a Gressner worm reducer and a duplex worm that meshes with the worm crown located on the plate. 7. The gearing head tilting mechanism, axis B – is made by a / 20 Nm_3000 rpm servo motor, a Gressner worm reducer and a worm gear-segment worm gear transmission. 8. The axial displacement mechanism of the gear head, Z axis – is made by a 20 Nm_3000 rpm servomotor, an Alpha Getriebe planetary reducer and a ball screw diam. 63 x 10, accuracy class IT3. 9. Top horizontal positioning mechanism, auxiliary axis X1 – a 20 Nm_ 2000 rpm servo motor, an Alpha Getriebe planetary reducer and a ball screw diam 63 x 10, precision class IT5.

Year of construction: 2007, condition: good (used), machine/vehicle number: 1380-1207, >with Siemens Sinumerik Panel Control >with chip conveyor >control panel >electric cabinet >capacity through spindle 60 mm >max. piece length 340 mm Ndjdpsm Nb Rijfx Apheb