Pellet production line

CPM 7932

Condition: excellent (used), We offer for sale the following Gránit-Mill 90 wood pelletizing presses, in the condition shown in the pictures, after the pelletizing plant has ceased operation. The machine is made in Hungary, our company has an excellent relationship with the manufacturer, and we can help you purchase parts. Drive and sticker handling is similar to the old CPM machines. The presses (with pine) are capable of 1.2-1.5 t/h/pc. Price: €29 900/press €49 900/ 2 presses Included in the price: pre-tank control cabinet dosing screw permanent magnet conditioner press motors pre-tank 1.1 kW feeder 1.5 kW conditioner 15 kW tablecloth 0.55 kW main engine 90 kW 3 stickers all three are made by La Meccanica barely used It has a 6 x 45 mm hole for pine Ijdpfsp T Twusx Af Ssbf 2 sets (total of 4) notched collars spare parts screws nuts breaker pin assembly aids Status: Engines and drives intact. Both machines tested. It is recommended to replace the neck bearing of the right machine. Smaller parts (such as the pellet cutter) must be replaced. There is no water supply, the place is prepared. The greasing method is manual, but central greasing can be easily installed. Summary: The machine on the left can be put into production immediately. It requires a minor service on the right side. If necessary, the machine can be tested at a pre-arranged time. Not in production, must be prepared. It is possible to check the mechanical durability and volume density of the produced pellets on site!

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Ijdpfswp Rqfsx Af Sjbf Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: like new (used), functionality: fully functional, Various Powerlock planing heads for WEINIG Powermat. 2pcs -240 mm-500€ Iodpoulmb Asfx Af Ssbf 3st -150 mm-350€ 4st -100 mm-320€ 3pcs - 60 mm-280€ Price per piece

Year of construction: 2004, condition: excellent (used), Stacking system with layer capping Ibedpfer Ndhasx Af Ssf Wood length: 3-5m Cutting height cross-cut: max 120mm Very good condition, professionally dismantled. Incl. associated switching equipment Modifications/ adaptations possible by arrangement

Condition: excellent (used), Finscan Nova and a CGV full trimmer Ijdewq A Edepfx Af Sobf

Year of construction: 2025, condition: like new (used), For Sale: 4 pieces of new spiral planing heads D 140 x 240 x 40 Z=6 Used only once as a demo, now available at a special price! Ibodpfowvictox Af Ssf Act fast and secure these high-quality spiral cutterehads heads that will revolutionize your woodworking projects. Don’t miss out on this opportunity, 60% of new price

Condition: refurbished (used), Year of construction: 2018, machine/vehicle number: R-00553, load capacity: 210 kg, arm reach: 2,450 mm, controller manufacturer: R-30iB B-Size, teach pendant manufacturer: A05B-2255-C101#EGN, Refurbished FANUC R-2000iC/210WE manufactured in 2018.07. The robot comes with an R-30iB B-Size controller including iPendant.   Ibsdsx Ib Tzopfx Af Sjf Our experts extensively tested the robot, after which we conducted a maintenance service according to the manufacturers’ specifications. The grease is examined for the amount of iron particles, indicating the corresponding axes' condition. Only robots in excellent mechanical condition will be completely refurbished, ensuring a long-term solution for our customers. This enables us to deliver our robots with a warranty term of 12 months as standard!   Brand: FANUC  Model: R-2000iC/210WE Model Number: A05B-1338-B201 Year of Manufacture Robot: 2018.07 Warranty term (months): 12   Payload (kg): 210 Reach (mm): 2450 Repeatability (mm): ± 0.1 Controlled Axes: 6-axis Installation Type: Floor Mount Weight (kg): 1180   Controller: R-30iB B-Size Year of Manufacture Cabinet: 2018.07 RCC Length (m): 7   Teach Pendant: A05B-2255-C101#EGN Teach Pendant Cable Length (m): 10

Condition: refurbished (used), Year of construction: 2016, machine/vehicle number: R-00536, load capacity: 125 kg, arm reach: 3,100 mm, controller manufacturer: R-30iB A-Size, teach pendant manufacturer: A05B-2255-C101#EGN, Refurbished FANUC R-2000iC/125L manufactured in 2016.12. The robot comes with an R-30iB A-Size controller including iPendant.   Our experts extensively tested the robot, after which we conducted a maintenance service according to the manufacturers’ specifications. The grease is examined for the amount of iron particles, indicating the corresponding axes' condition. Only robots in excellent mechanical condition will be completely refurbished, ensuring a long-term solution for our customers. This enables us to deliver our robots with a warranty term of 12 months as standard!   Brand: FANUC Model: R-2000iC/125L Model Number: A05B-1333-B261 Ijdex Ebnwopfx Af Sebf Year of Manufacture Robot: 2016.12 Warranty term (months): 12   Payload (kg): 125 Reach (mm): 3100 Repeatability (mm): ± 0.05 Controlled Axes: 6-axis Installation Type: Floor Mount Weight (kg): 1115   Controller: R-30iB A-Size Year of Manufacture Cabinet: 2016.12 RCC Length (m): 7   Teach Pendant: A05B-2255-C101#EGN Teach Pendant Cable Length (m): 10

Condition: used, knife: Reversible blade Centrolock Z2 flight circle (ø): 93 / 130mm admission: PowerLock HSK 85W length: 240 / 255mm Ibsdpfx Ast N Ahtof Sjf material: steel