Used thread rolling machines for sale (63)

Condition: used, Recently arrived WMW UPW 25 with 8 sets of rolls JUST FOR 6,500.00 EURO 8 SETS OF ROLLS (INCLUDED) Gijdoygm Hvjpfx Acfeu FREE LOADED ON TRUCK

Condition: good (used), Rolling pressure 220 kN Ø Pieces 3mm min; 70mm max Pitch 6mm max Grooving pitch 2.25mm max Gedpevyyyxofx Acfoiu Roller width 160mm max Ø Roller 133mm min; 170mm max Roller shaft speed 24 30 38 45 62 72 90 114 rpm Ø Roller carrier shaft 54mm standard; 69.85 special Distance between shafts 135mm min; 230mm max Working stroke 15min max Feed rate 0.5mm/s to 6mm/s Laminating time 0.1s to 100s Pause time 0.1s to 100s Main motor 5.5 Kw Electrical power consumption 8.6 Kw Tank capacity 130 L Weight approx 2100 Kg

Condition: used, Year of construction: 2004, ORT RP30 C thread rolling machine 2-roll 30 tons electronic control of speed and position. Brushless motors for the rotation of the rollers Possibility to memorize the parameters for the piece. The machine is visible working in our warehouse in Gussago BS. Test possibility Mimu Machine Tools Rolling is a mechanical processing without chip removal that can be performed cold or hot, having as an aim the improvement of the surface finish (therefore the apathetic behavior of the material. Gijdpjyzt T Tsfx Acfou Power (Ton): 30 Number of rollers: 2 PLC: YES

Condition: used, Year of construction: 2007, Manufacturer: ORT Model: RP18 Year : 2007 Maximum rolling thrust 18 Ton Roller shaft diameter 54 mm Roller shaft key 12 mm Minimum diameter workpiece to rolled 3 mm Maximum diameter workpiece to be rolled 60 mm Max.length workpiece rolled in plunge-feed 175 mm Max.length workpiece to rolled in enfilade — Maximum Pitch workpiece to be rolled 4 mm Maximum roller diameter 185 mm Main motor power 7,5 HP Total installed power 11 HP Giodpfsv Tqdbjx Acfeu Maximum noise level 80 db Net weight 1800 kg Height Rolling shaft from the floor 1035 mm Machine width 1450 mm Standard machine depth 900 mm Total machine height 1800 mm

Condition: used, ORT RP18B overhauled Godpouua H Refx Acfjiu

Condition: refurbished (used), Thread rolling machine ORT RP18 B 2-roll Gisdpfovxa Dbox Acfou overhauled See video The machine is in our warehouse in Gussago BS, under power Test run possible Mimu Machine Tools Italy Power (Ton): 18 Number of rollers: 2

Condition: refurbished (used), CNC thread rolling machine - electronic retrofit with Siemens PLC and touchscreen Thommen PR17 CNC 2-roll Rollers rotation speed electronically managed Position and speed managed electronically Spindles diameter 54mm 2 pairs of supports (closed and open) The machine is in our warehouse in Gussago BS, under power Test run possible Mimu Machine Tools Italy Power (Ton): 17 Number of rollers: 2 Godpfeilh Tisx Acfoiu CNC: Yes

Condition: used, Thread rolling machine ORT RP18 2-roll Spindles diameter 69.95mm Gjdst Apugjpfx Acfsiu See video The machine is in our warehouse in Gussago BS, under power Test run possible Mimu Machine Tools Italy Power (Ton): 18 Number of rollers: 2

Condition: used, ORT RP12 Giedpfxeyvk S Aj Acfou 2-roll 12 ton Thread rolling machine The machine is in our warehouse, under power

Condition: used, Thread rolling machine ORT RP30U 2-roll Gisdpfst H Ty Ujx Acfsu 30 ton swiveling heads variable speed drive #1331 Under power in our warehouse in Gussago BS. Test run possible M i m u Machine Tools Italy Rolling is a mechanical process without chip removal that can be performed cold or hot, having as a purpose the improvement of the surface finish (therefore the fatigue behavior Power (Ton): 30 Number of rollers: 2

Condition: refurbished (used), Year of construction: 2026, ORT RP30 MS 2-roll 30 tons Gedpfsuykz Djx Acfeiu thread rolling, knurling, small gears 2009 = YOM Electronic overhaul and electronic retrofit with Siemens PLC (2026) The machine is visible working in our warehouse in Gussago BS. Possibility of proof M i m u Machine Tools Power (Ton): 30 Number of rollers: 2 PLC: Yes

Condition: new, Thread rolling machine Godpfoyz Th Rjx Acfjiu

Condition: used, Year of construction: 2007, pressure 20 - 300 kN Gijdpow E Nmkjfx Acfsu adjustment of rolling slide 50 mm diameter of rolling spindle 120 mm roll spindle height over machine bed 200 mm Control SIN 840 D taper length of the roll spindle 200 mm rolling spindle turning speeds 0 - 50 1/min torque per rolling spindle 2700 Nm power capacity 2 x 8,4 kW distance between rolling spindles min. 271 / max. 368 mm rolling tool outer diameter max. 300 mm total power requirement 26 kW weight of the machine ca. 7,1 t dimensions of the machine ca. 9,70 x 4,50 x 3,80 m CNC machine for gear cold rolling / thread rolling Hydraulic rolling process Felsomat loader cell Complete housing

Condition: used, Year of construction: 1990, functionality: fully functional, thread length: 75 mm, workpiece diameter (max.): 45 mm, spindle diameter: 54 mm, type of input current: three-phase, roll diameter: 150 mm, spindle speed (max.): 60 rpm, spindle speed (min.): 40 rpm, roll width: 80 mm, High-precision thread rolling is available with 6 tons of pressure. The machine is in perfect condition. Really easy for adjusting and high-precision of thread rolling process. Technical data: - Minimum / maximum diameter of the rolled detail: 3/45 mm; - Maximum rolled thread pitch: 2.5 mm; - Maximum rolled length of the thread: 75 mm; - Minimum / maximum distance of rolling spindles,: 125/180 mm; Giedpfx Acjy Hp I Rjfeu - Maximum diameter of rolling tools: 150 mm; - Diameter of rolling spindles: 54 mm;

Condition: good (used), functionality: fully functional, type of input current: AC, Pee-Wee Model P24US Hydraulic Thread Rolling Machine for in-feed or thru-feed rolling with helical thru-feed dies Max. rolling pressure: 24 tons Max rolling diameter: 75mm Min rolling diameter: 5mm Max rolling width: 200mm Diameter of rolling spindles: 69.85mm Gsdpfx Aexl Ebhocfsiu Max thread die diameter:210mm Variable spindle speeds: 20 -90 rpm

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Gijdpfx Ajuz If Nocfeu Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: used, Thread rolling machine, cold rolling machine, thread rolling machine, profile rolling machine Manufacturer PEE-WEE Type P 24 Q serial no. LC2403099 year of construction 2004 Rolling force max. 24 ton. Tool diameter max. 200 mm Rolling spindle diameter 69,85 mm Tool bore diameter 70 mm (nominal diameter) Tool length, tool length max. 180 mm Workpiece diameter max. 50 mm Rolling spindle speed 22 - 44 - 95 - 190 rpm Motor power hydraulics approx. 3 kW Motor power roller drive 5.5 kW Mains connection 400 Volt, 50 Hz - Swivel roller spindle for threaded continuous rollers - Rolling spindle speed in 4 stages via gear changeover - Hydraulic system integrated in the machine bed Space requirement L x W x H 2000 x 1750 x 2550 mm Weight approx. 3 tons good condition Grooving rollers: The thread rolling tools with the same pitch as the workpiece form the thread by penetrating into the workpiece up to the nominal diameter. The thread length is maximum as long as the rolling tools are wide. Continuous rolling: When the thread length is greater than the rolling tool width. Through-feed tools have 3 sections - the infeed, the calibration section and the outfeed. Grooved rollers have no pitch and are swiveled with the pitch angle of the profile to be rolled. Pitch rollers differ from grooved rollers in that they have a pitch in the profile. Gjdsh A S Htepfx Acfeiu The sum of the pitch angle and the swivel angle gives the pitch angle in the workpiece.

Condition: ready for operation (used), Year of construction: 1995, Thread Rolling Machine Flat Die TLM RP8 Operational, fully functional Available for any tests c/o H.B.R. srl Ready for immediate delivery. TLM RP8 Informazioni tecniche: Year: 1995 Diameter range: 3 – 8 mm. Shaft length under head: 90 mm. Max. thread length: 52 mm. Giodpfx Aceyzqzbsfsu Dies size:130/115x54 mm. Speed: 420 pcs./min. Vibratory feeder Condition: very good, operational Ready for immediate delivery Machinery runs without any problems. Available c/o H.B.R. srl - Italia

Condition: used, Year of construction: 1997, machine/vehicle number: 707, Ingramatic thread rolling machine RP21 RV, year 97, used Godpfx Aswiu Afjcfeiu

Condition: excellent (used), Year of construction: 2009, functionality: fully functional, machine/vehicle number: 063/09, thread length: 50 mm, workpiece diameter (max.): 6 mm, SMART MACHINERY NG S-DD Thread Rolling Machine Fully operational, currently in production. Year: 2009 Incoterm: EXW Calolziocorte (LC) The machine automatically sets up for stroke change. The NG S-DD thread rolling machine is equipped for changing the ram stroke depending on the length of the comb used. Minimum pass-through diameter: 1 mm. Maximum pass-through diameter: 6 mm. Maximum threaded length: 50 mm. Maximum rivet length: 80 mm. Gedpfxsyycr Ne Acfoiu Maximum output: 700 pcs/min. Main motor power: 13.9 kW Installed electric power: 16 kW

Condition: excellent (used), workpiece diameter (max.): 30 mm, spindle diameter: 54 mm, roll diameter: 125 mm, spindle speed (max.): 224 rpm, spindle speed (min.): 40 rpm, roll width: 70 mm, Excellent Used Profiroll Bad Duben Model UPWS 10 ton Hydraulic Thread Rolling Machine with swivelling spindle for in-feed and thru-feed rolling Max rolling diameter: 30mm - Max thread length infeed rolling: 70mm - Max thread length thru-feed rolling: infinite Gisdpfoymlx Dsx Acfou Dia. of rolling spindles: 54mm - Max size of thread dies: 125mm dia x 70mm wide - 4 spindle speeds 40 to 224 rpm

Condition: used, Thread rolling machine, thread rolling machine, segment thread rolling machine, cold forming machine, thread rolling head, rolling head -Manufacturer:BWF, thread rolling head -Type: RK 12-20 -Thread rollers: M24 x 1.5 -Dimensions: Ø 120 x 180 mm Gsdpfeu Tyvhox Acfeiu -Weight: 5.6 kg

Condition: good (used), Maximum pressure 25tn • 69 and 85mm axles Godpfxogqumpo Acfsiu • Machine in very good condition, completely revised

Condition: used, Year of construction: 1996, Thread rolling machine Ingramatic RP21 RV With sems unit Flat dies Year: 1996 Diameter : max 8 mm Shaft length under head: 80 mm Gedpfjylw N Sjx Acfjiu Max. thread length: 58 mm

Condition: used, Year of construction: 1994, Thread Rolling Machine EWMenn GW63 Flat dies Year: 1994 Diameter range: max 8 mm Gsdpfx Acjylw E Tofoiu Shaft length under head: 80 mm Max. thread length: 58 mm