Condition: used, Rohde & Schwarz Radio Frequency Interference Receiver Type: ESPI3 Frequency Range: 9 kHz to 3 GHz IF Resolution Bandwidths (RBW): 200 Hz (CISPR), 9 kHz (CISPR), 120 kHz (CISPR), 1 MHz, as well as 10 Hz to 10 MHz in 1-3-10 steps CISPR Bandwidths: < 150 kHz = 200 Hz, 150 kHz–30 MHz = 9 kHz, > 30 MHz = 120 kHz Detectors: Max Peak, Min Peak, Quasi-Peak (CISPR 16), Average, RMS Up to 3 detectors can be activated simultaneously Input Attenuation: 0 dB to 70 dB in 10-dB steps Optional Preamplifier ESPI-B2: 9 kHz to 3 GHz, 20 dB gain Noise Figure: approx. 18 dB without preamplifier, approx. 10 dB with preamplifier Start and stop frequency can be set freely Step width can match the reception frequency (harmonic measurement) Display Units: dBm, dBµV, dBµA, dBpW, dBpT Measurement Functions: EMI according to CISPR, APD, CCDF, Continuous and Single Measurement Weight: 1 kg Condition: used Scope of Delivery: (See image) (Subject to changes and errors in the technical data and specifications!) We will gladly answer any further questions you may have over the phone. Lhsdpfx Aszimlvjdcsn

Condition: used, Keysight Mixed Signal Oscilloscope / Digital Storage Oscilloscope Keysight / Agilent InfiniiVision MSO-X 3034A 350 MHz Mixed Signal Oscilloscope with 4 analog channels, 16 digital channels, and 4 GSa/s sampling rate For sale is a used Mixed Signal Oscilloscope from the manufacturer Keysight Technologies / Agilent Technologies. The device is suitable for precise signal and measurement tasks in development, laboratories, service, training, research, as well as industrial electronics and quality assurance. Technical data Manufacturer: Keysight Technologies / Agilent Technologies Type: MSO-X 3034A Series: InfiniiVision Device type: Mixed Signal Oscilloscope / Digital Storage Oscilloscope Bandwidth: 350 MHz Analog channels: 4 Digital channels: 16 Max. sampling rate: 4 GSa/s Display: Color display MegaZoom technology Inputs: 4x analog BNC inputs Digital input / Logic connector USB port USB Device / USB Host Trigger Out Ext. Trigger / Calibration connector Power connection: 100 - 240 V AC 50 / 60 Hz Power consumption: max. 100 W Dimensions: approx. 381 × 204 × 142 mm Weight: approx. 4 kg Features Large color display Front-panel control buttons 4 analog channels 16 digital channels USB interfaces Trigger functions Analysis functions Measurement functions Storage and printing functions Carrying handle Accessories as shown in the pictures Application areas Electronics development Laboratory Service Troubleshooting Signal testing Printed circuit board testing Training Research and development Quality assurance Industrial electronics Scope of delivery Keysight / Agilent InfiniiVision MSO-X 3034A 3x probes as shown in the pictures Power cable Lodpfezh I Dwex Adcjhn Accessories as shown in the pictures Condition Used Optical condition as shown in the pictures Device can be switched on Display and operation appear to be functioning properly Test seals / stickers as shown in the pictures are present Weight: approx. 4 kg The table shown in the photos or other items not explicitly mentioned are not included in the sale. Shipping is possible. Subject to changes, errors and prior sale. We would be happy to answer any further questions by telephone.

Condition: used, SincoTec Lhjdpfx Adszii A Docon Type: POWER SWING 20 kN POWER SWING 20 kN resonance testing system Sincotec Power Swing 20 kN resonance testing system Manufacturer's maintenance performed General information For sale is a used Power Swing 20 kN resonance testing system from Sincotec Test Systems GmbH. The testing system was used in a single-shift operation, and all maintenance work was performed regularly by the manufacturer. Special features: Robust construction for continuous operation Precise resonance testing up to 20 kN Manufacturer's maintenance available Ideal for research, testing, and development applications Technical data – Testing system Feature / Value Overall height of testing system 1215 mm (without clamping device) Width of testing system 2005 mm Depth of testing system 1205 mm Maximum force amplitude 10 kN Maximum total force ±20 kN Accuracy of measuring sensors min. Class 1 (according to DIN EN 10002-3) Technical data – Control cabinet Feature / Value Overall height of control cabinet approx. 1800 mm Height of tabletop 1080 mm Width of control cabinet 650 mm (narrow tabletop) / 1450 mm (wide tabletop) Depth of control cabinet 700 mm (narrow tabletop) / 800 mm (wide tabletop) Weight 152 kg (small tabletop) 187 kg (large tabletop) with (granite plate) 247 kg Conditions for the installation site Feature / Value Space requirement 4.3 × 3.0 m Required ceiling height 2.5 m Floor load-bearing capacity 234 N/cm² Mains conditions Feature / Value Voltage 400 V three-phase with neutral conductor and protective earth Phase sequence Right-rotating field Voltage fluctuations ≤ ±10 % Short-time dips < 20 ms Limits for sustained disturbances Radio interference level A according to VDE 0871 Frequency 50 Hz ± 1 % Protective earth / Grounding resistance < 0.3 Ω Connection and protection Feature / Value Voltage supply 400 V / 50 Hz (Right-rotating field) Connection plug CEE socket, 5-pole, 16 A Protection 16 A Weight of testing system approx. 3.6 t Max. weight clamping device 250 kg Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We would be happy to answer any further questions you may have by phone.

Condition: used, ZEISS Multisensory CNC Coordinate Measuring Machine O-INSPECT 442 Professional coordinate measuring machine for optical and tactile precision measurements in industry, research, and quality assurance. For sale is a used multisensory coordinate measuring machine from the manufacturer Carl Zeiss IMT GmbH. The ZEISS O-INSPECT 442 combines highly precise optical and tactile measurement technology in a CNC coordinate measuring machine. The installed ZEISS CALYPSO measurement software enables convenient evaluation of measurement data as well as the display of the actual state, target profile, and deviations. The system is ideal for quality assurance, toolmaking, precision engineering, medical technology, as well as research and development. Technical data: Manufacturer: Carl Zeiss IMT GmbH Model: O-INSPECT 442 Type: Coordinate measuring machine Measuring range X: 400 mm Measuring range Y: 400 mm Measuring range Z: 200 mm Max. workpiece weight: 20 kg Noise level: < 70 dBA Measurement system: Multisensory measurement system Optical and tactile measurement CFS measuring head system CALYPSO measurement software CNC-controlled measurement sequences Electrical data: Supply voltage: 100 / 110 / 120 / 125 / 230 / 240 V AC (±10 %) Current type: 1 / N / PE Frequency: 50–60 Hz (±3.5 %) Power consumption: max. 1500 VA Dimensions: Width: 1,055 mm Depth: 1,351 mm Height: 1,770 mm Weight: Coordinate measuring machine: approx. 800 kg Max. workpiece weight: 20 kg Equipment: Integrated control Control panel Computer with peripherals ZEISS CALYPSO Software 5.2 Documentation CFS measuring head system Reference probe Calibration standard Calibration template Applications: Coordinate measuring technology Optical measuring technology Tactile measuring technology Quality assurance Toolmaking Precision engineering Medical technology Research and development Scope of delivery: ZEISS O-INSPECT 442 coordinate measuring machine Integrated control Control panel Computer with peripherals ZEISS CALYPSO Software 5.2 Documentation Measuring head system Reference probe Calibration standard Calibration template Lhsdpfxjzii Dho Adcen Accessories as shown in the pictures Condition: Used Optical condition as shown in the pictures. Normal signs of wear and tear due to age. The table shown in the photos or other items not explicitly mentioned are not included in the sale. Due to its size and weight, shipping is possible via a freight forwarder. Subject to changes, errors and prior sale. We would be happy to answer any further questions by telephone.

Condition: used, FRT MicroSpy Device Designation: FRT MicroSpy Mobile Art. No. MSP 105 00 Device Number: MSP1033 FRT MicroSpy Mobile Portable Optical Profilometer for non-destructive 3D surface measurements directly on the component. Due to its portability, the MicroSpy Mobile is ideally suited for mobile use on large machines, vehicles, rollers, glass panes, or other large components. This enables high-resolution and non-destructive measurements on-site to determine important characteristics of surfaces, such as roughness, contour, topography, layer thickness, wear, load-bearing capacity, or volume. Smaller samples can be measured directly on the measuring table. Usable on large construction and machine parts Excellent resolution values Excellent reproducibility Non-destructive measurement Handles and adjustable support feet Low weight (approx. 5 kg) FRT Technical Specifications: Device: MicroSpy Mobile xy-travel range: 50 x 50 mm² xy-table Type: compact XY cross table with open frame Bearing: mechanical crossed roller guide Drive: DC motor with ball screw Travel range (XY measuring range): 50 x 50 mm² (or 20 x 20 mm² with CWL 3mm) Position measuring system: rotary encoder Measuring system resolution: 0.25 µm XY repeatability: < ± 1 µm Table height deviation (per axis): < 2 µm / 50 mm (of which is not reproducible): < 0.5 µm XY squareness: < 4 µm / 50 mm z-axis, motorized: Type Position Drive Travel range Position measuring system Measuring system resolution Axis straightness Gross adjustment, manual: Type: dovetail guide with fine drive Adjustment range: 25 mm Measurement: Minimum point spacing xy: 1 µm Sample size: - Sample weight: - Min. measuring speed: 1 µm / sec Max. measuring speed: 50 mm / sec Overall system: Total weight: approx. 150 kg of which measuring unit: approx. 5 kg Footprint measuring unit: approx. 0.3 x 0.3 m² Dimensions controller (W x D x H): approx. 0.65 x 0.65 x 1.0 (1.6) m³ Voltage supply EU version: 110 - 240V, 50 - 60Hz, z 16A Voltage supply US version: 110 - 240V, 50 - 60Hz, z 16A Power consumption: typ. 300-400 W Ljdpfx Adszdnqcscjhn Compressed air supply: - Ambient temperature: 22°C ± 5°C Temperature stability: < 0.5°C/h Environmental conditions: measuring room Scope of delivery: 1 x XY table with 50 x 50 mm² travel range 1 x Mobile base with electronics 1 x Chromatic sensor FRT CWL 600 µm 1 x Electronics for chromatic sensor 2 x Keys for computer 2 x Keys for rear door 1 x Power cord for power supply 1 x Mouse (PS/2) 1 x Keyboard 1 x 19'' TFT monitor Type: FRT MicroSpy Mobile Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have by telephone.

Condition: used, Automation Assistant Oy Linear Guided Free Fall Tester Automation Assistant Oy LG2750 Professional linear guided free fall test stand for reproducible drop and impact tests For sale is a used Linear Guided Free Fall Tester from the manufacturer Automation Assistant Oy. The test stand is suitable for reproducible drop and impact tests in research, development, quality assurance, and industry. Operating manual and electrical documentation are available. Technical data: Lhjdpfx Adjzn Uqdjcon Manufacturer: Automation Assistant Oy Type: LG2750 Machine type: Linear Guided Free Fall Tester Made in Finland Power supply: 230 V AC / 50 Hz Max. current consumption: 10 A Control voltage: 24 V DC / 2.5 A Pneumatic supply: max. 8 bar Impact material: Concrete garden brick 300 × 300 × 50 mm Dimensions (approx.): Width: 850 mm, Depth: 900 mm, Height: 2750 mm Total weight: approx. 210 kg Test tower: approx. 155 kg Impact table: approx. 55 kg Equipment: Touchscreen control panel Enclosed safety cabinet with protective glazing Linear guided drop sled Pneumatic gripper SMC pneumatic components Emergency stop system Impact table with concrete impact plate Electrical documentation available Accessories as shown in the pictures Application areas: Drop tests Impact tests Product testing Quality assurance Research and development Laboratory and industrial applications Scope of delivery: Automation Assistant Oy LG2750 Linear Guided Free Fall Tester Operating manual Electrical documentation Accessories as shown in the pictures Condition: Used Visual condition as shown in the pictures. Normal signs of wear and tear due to age. Shipping by freight forwarder is possible. Subject to changes, errors and prior sale. We will gladly answer any further questions by telephone.

Condition: used, Brüel & Kjær LDS Dactron Shaker Control System / Vibration Testing Controller LDS Dactron LASER USB LAS 200 Controller for electrodynamic vibration testing systems For sale is a used Shaker Control System from the manufacturer Brüel & Kjær LDS Dactron. The system is suitable for controlling electrodynamic shaker systems for vibration, resonance, random, and shock tests in research, development, and quality assurance. Technical data: Manufacturer: Brüel & Kjær LDS Dactron Type: LASER USB Model: LAS 200 Device type: Shaker Control System / Vibration Testing Controller Lsdezrtylspfx Adcohn Country of manufacture: Made in U.S.A. Mains connection: 100–240 V AC Mains frequency: 47–63 Hz Power consumption: 1 A Analog inputs: 8 × BNC Outputs: 2 × (Drive / COLA) USB interface Digital I/O Master/Slave interfaces Emergency stop connection Calibration: Calibrated: 09/12/2023 Due: 09/11/2024 Dimensions: approx. 430 × 350 × 90 mm (W × D × H) Weight: approx. 6–8 kg Equipment: USB license dongle Power cable 8 measurement inputs USB interface Digital I/O Documentation as shown in the pictures Application areas: Vibration testing Oscillation testing Random tests Resonance tests Shock tests Endurance tests Test rig control Scope of delivery: 1 × LDS Dactron LASER USB LAS 200 Shaker Control System USB license dongle Power cable Documentation as shown in the pictures Condition: Used Optical condition as shown in the pictures Calibration sticker present Important note: The license keys visible in the documents have been obscured for data protection and security reasons. The table shown in the photos, as well as any other items not explicitly mentioned, are not part of the sale. Shipping possible. Subject to changes, errors, and prior sale. We would be happy to answer any further questions by telephone.

Condition: used, functionality: unexamined, Dear Sir or Madam, We are pleased to offer the following piece of equipment for sale: Keyence VL-700 coordinate measuring machine. The machine is being sold with the equipment shown in the photographs and specified in the advertisement text. Lodpfx Adez Sxq Uscjhn Location: 40764 Langenfeld PLEASE NOTE! This equipment originates from an insolvency. We are auctioning it off to the highest bidder on behalf of the creditor/bank. This is a closed auction. We do not provide any information regarding the current highest bid. Your bid becomes binding upon receipt by email. Please submit your binding bid by 10.00 on 3 November 2026. Once the auction has ended, you will be informed of the outcome within 72 hours.

Condition: used, Binder Lhsdpfx Asziyymsdcen Type: VDL 115 Binder Safety Vacuum Drying Oven For sale is a BINDER VDL 115 safety vacuum drying oven for professional use in laboratories, industry, and research. Device description: The BINDER VDL 115 is an explosion-proof vacuum drying oven for gentle drying, degassing, and conditioning of materials under vacuum. The device is specifically designed for applications involving flammable solvents and meets high safety requirements (ATEX version). Due to the precise control of temperature and pressure, the device is ideally suited for reproducible laboratory and industrial processes. Typical applications: Chemical and pharmaceutical laboratories Research & development Quality control Industrial drying processes under vacuum Temperature / Vacuum: Temperature range: +9 °C above ambient to approximately +110 °C Final vacuum: up to approximately 0.01 mbar Electronic temperature and pressure control Equipment: Safety glass pane with splinter protection ATEX-compliant design Several insertion levels (number depending on the configuration) Connections for vacuum and inert gas Dimensions: Internal volume: approximately 115–119 liters Internal dimensions (W × D × H): approximately 506 × 460 × 506 mm External dimensions (W × D × H): approximately 743 × 581 × 942 mm Electrical data: Rated power: 1.90 kW Mains connection: 230 V / 1N~ Current consumption: 8.3 A Frequency: 50–60 Hz Protection class: IP54 Rated temperature: 200 °C Temperature protection: DIN 12880, Class 2.0 Weight (empty): approximately 158 kg Important note: "The table shown in the photos is not included in the sale." Condition: used Scope of delivery: (See image) (Changes and errors in the technical data and information are subject to change!) We will gladly answer any further questions you may have by telephone.

Condition: used, RMS Technical specifications (manufacturer/model type – no guarantee): Lodpszikc Sofx Adcohn Peak force: “according to the manufacturer’s specifications” in the range of approximately 10 kN. Max. acceleration: “up to approximately 1,000 m/s²” Max. speed: “typically in the range of approximately 1 m/s to a few m/s” Components: Control cabinet TGA 022/3 Vibration exciter SW 6507 Power amplifier TG D 9000-000.00 Fan Condition: used Scope of delivery: Vibration testing system as shown in the picture (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have over the phone.

Condition: ready for operation (used), functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! Loading: December 1st to December 10th. TECHNICAL DETAILS Dimensions Length: 2,500 mm Width: 1,350 mm Height: 500 mm MACHINE DETAILS Machine type: Granite measuring plate Lodpfx Ado Adux Decehn Weight: 2,000 kg

Condition: used, GE Druck Modular High-Precision Pressure Controller / Pneumatic Pressure Controller PACE5000 Professional High-Precision Pressure Controller for calibration, pressure testing, automation, and laboratory applications For sale is a used high-precision pressure controller from the manufacturer GE Druck. The PACE5000 is a modular, high-precision pressure control system designed for the most demanding applications in calibration laboratories, research, development, production, and quality assurance. Due to its high control speed and precision, the device is ideally suited for automatic pressure tests, calibration tasks, and industrial measuring and testing systems. Technical data: Manufacturer: GE Druck (Baker Hughes) Model: PACE5000 Device type: Modular High-Precision Pressure Controller Pneumatic Control Module: CM0-B-16G Dimensions: approx. 440 × 88 × 320 mm (W × H × D) Weight: approx. 10.1 kg Control range: -1 to 70 bar(g) Maximum permissible operating pressure (MWP): 94 bar Accuracy: up to 0.001% of the final value (model-dependent) Long-term stability up to 0.001% FV Features: Modular control system Very high pressure control speed Automatic pressure control Pressure testing Leak test function Burst test Switch test Programmable test sequences User-defined pressure units Display: Color touch display Graphical user interface Display of setpoint and actual value Intuitive menu navigation Interfaces: Ethernet USB Host USB Device RS-232 CAN IEEE-488 (GPIB) 24 V DC inputs/outputs Pneumatic connections: Supply Output Vent Reference G1/8" connection Lhjdpfoziyqrjx Adcen Power connection: 100–230 VAC 50–60 Hz Power consumption: max. 100 VA Application areas: Calibration laboratory Testing systems Quality assurance Automotive industry Aerospace Mechanical engineering Measurement technology Research & Development Automation technology Pressure sensor calibration Equipment: Color display Pneumatic Control Module Ethernet USB RS232 CAN IEEE-488 (GPIB) Pressure connections Power cable Accessories as shown in the pictures Scope of delivery: GE Druck PACE5000 Power cable Accessories as shown in the pictures Weight: approx. 10.1 kg Condition: Used Optical condition as shown in the pictures. Normal signs of wear and tear due to age are present. The table shown in the photos and any other items not explicitly mentioned are not included in the sale. Shipping via parcel service or freight forwarder is possible. Subject to changes, errors, and prior sale. We will be happy to answer any further questions by telephone or e-mail.

Condition: used, SHI Machines Type: BlueBox As good as new, with only 250 operating hours! Technical data: Power: 120 kW Torque: up to 470 Nm Speed: up to 6,000 rpm Operation: Four-quadrant operation Safety package: Bulletproof cover & data filter for "Go" signal line Dimensions: approx. 2800 × 1600 × 1300 mm Accessories, etc.: 1 clutch 120 - steel, incl. adapter Clutch size: 100 Max. speed: 7,300 RPM Max. torque: 1,000 Nm 1x adapter 1x clutch steel size 100 1x adapter 2 ø40 1x adapter 2 ø50 1x adapter 2 ø60 1x clamping device ø40 1x clamping device ø50 Lhjdpfx Aey Tg R Nsdcjn 1x clamping device ø60 Adapter mounting tool Clutch 120 - CFRP, incl. adapter Max. speed: 8,500 RPM Max. torque: 720 Nm Adapter mounting tool CISPR 25 test table made of wood on wheels for EMC BlueBox 120, size 2500 x 1000 x 900 mm Loadable up to max. 500 kg, incl. 2 mm hot-dip galvanized ground plane Payload: up to 1,400 kg Weight: approx. 2,500 kg Operating voltage 400 V, 250 A Control voltage 24 V Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: used, Keyence KEYENCE XM-2000 with XM-H1000 – 3D Coordinate Measuring System (CMM) Year of manufacture: 2020 Professional handheld measuring system for precise 3D measurements directly in the production environment. Lhsdozii Dnopfx Adcsn Item description: For sale is a used KEYENCE XM-2000 coordinate measuring system, including the XM-H1000 handheld probe. This innovative system enables precise 3D measurements directly at the workplace – without a measuring room, without complex setup, and without specialized CMM knowledge. The device is ideally suited for manufacturing companies, quality assurance, initial sample inspection reports (ISIR), in-process controls, and reverse engineering. Technical data – KEYENCE XM-C1000 / XM-H1000 (XM series) Measuring system (general) Feature: Measuring range (XYZ) approx. 600 × 300 × 200 mm (depending on the configuration) Measuring accuracy ±(8 + L/80) µm (L = measuring length in mm) Repeatability ±3 µm (typical) Resolution 1 µm Measuring principle - Optical tracking with camera-based detection Calibration - User calibration possible with calibration sphere CAD comparison - Directly on the device (STEP, IGES, etc.) Export formats - PDF, Excel, CSV, DXF Tolerance evaluation - Automatic with color comparison XM-C1000 – Control and evaluation unit (controller) Component: Display - 15-inch touchscreen Connections - USB, LAN, HDMI, power connection Storage options - Internal + USB export Software functions - Measuring, CAD comparison, report generation Operation - Touchscreen + button operation Languages - Multilingual (including German) XM-H1000 – Handheld measuring probe Feature: Probe type - Handheld with push button Feedback - LED status indicator, vibration signal Probe tip - Replaceable, various tips available Tracking - Detected via the controller's camera system System properties Feature: Operating temperature: 10 – 35 °C Voltage supply: 100–240 V AC, 50/60 Hz System size (complete) - approx. 800 × 600 × 800 mm (depending on the configuration) Weight (total system) - approx. 25–40 kg (depending on the configuration) Mounting - On table or optional measuring table Scope of delivery: KEYENCE XM-2000 control and evaluation unit KEYENCE XM-H1000 handheld measuring probe XM-C1000 (controller) Camera unit / tracking module Connection cables and power supplies Condition: Used, fully functional, in very good condition. Shipping & delivery: Shipping by freight forwarder Self-collection possible by arrangement. International shipping possible upon request. If you have any questions, require further information, or would like to arrange a viewing appointment, please do not hesitate to contact us. (Changes and errors in the technical data and information are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: used, Oxford Instruments Lhsdezd Ru Dopfx Adcjn Type: INCAx-act + 2 x-stream mics + PC and software INCAx-act Analytical Drift Detector Microanalysis of elements, including boron and above Operating temperature Normal mode: 10-25 degrees Operating temperature Extended mode: 10-30 degrees Storage temperature -25 to 40 degrees and 8 to 80% relative humidity, non-condensing Operating humidity

Condition: used, Technical details: traction force: 250 kN control: SCHENCK HYDROPULS PSB dayligth: 1000 - 1200 je nach Spannwerkzeug /acc. clamp.tool mm piston stroke: 180mm mm A servo-hydraulic leaf spring testing machine with Series 65 digital electronics is designed for testing leaf springs used in commercial vehicles, railway vehicles, and industrial applications. A hydraulic actuator applies defined loads while force, displacement, and, if required, strain are measured. Typical tests: ·Static spring characteristic (force-displacement curve) ·Fatigue and endurance testing ·Cyclic load testing ·Service life testing ·Tensile and compression testing ·Production quality control Lhsdjzi R R Aspfx Adcsn *

Condition: used, Atlas Type: CI3000 F Atlas CI3000 Xenon Fade-Ometer The Ci3000+ Weather-Ometer and the Fade-Ometer, with their advanced digital control systems, represent significant advancements in the application of digital and optical technologies in easy-to-use laboratory weathering equipment. The 3000 series has been approved by many OEMs in the textile, paint, and coatings industries, as well as in the plastics industry, as an exclusive platform for precise, reproducible, and repeatable results for predicting service life. Features: Lsdozg Tmhepfx Adcehn Climate type Test type: Sunlight simulation Light source: Xenon arc lamp Applications: Additives and dyes Adhesives and sealants Architecture and construction Automotive industry Food and beverages Graphics Packaging Paints and coatings Photovoltaics Plastics Textiles Wind and solar Consumer electronics Compressed air supply The CI3000's humidification system uses a compressed air ultrasonic spray nozzle. Before entering the system, the compressed air must pass through a water/oil separator. The small air regulator in the CI3000 contains a second water-oil filter and a 5-micron solid particle filter. Ensure that a separate oil-water separator is installed and do not rely on the air regulator filter, as it is designed only as an additional device. Compressed air specifications Pressure: 80-100 PSI (552-689 kPa) Flow rate: 4 CFM (0.11 m³/min) Dimensions: Overall dimensions of the CI3000 37.5" Width x 29" Depth x 72" Height (95 cm Width x 73 cm Depth x 183 cm Height) Required footprint: 41.5" Width x 80" Depth (105 cm Width x 203 cm Depth) Total weight: 404 kg Voltage: 380-220 V 38 A 50 Hz ~3/N/PE 8 kW 404 kg Condition: used Scope of supply: (See image) (Subject to changes and errors in technical data and information!) We would be happy to answer any further questions you may have by telephone.

Condition: used, Zwick / Roell Zwick Indentec Hardness Tester Type: 4150DLC-A Technical Data: Available test forces: 60, 100, and 150 kgf Power supply: 115 / 230 V (50 - 60 Hz) 2/1A 1L/N/Pe + EO-4010C camera and ueye software Condition: used Lhodpfx Adjzh D Rajcsn Weight: approx. 60 kg Scope of delivery: (See image) (Subject to changes and errors in the technical data and specifications!) We will be happy to answer any further questions you may have by phone.

Condition: used, RMS RMS vibration exciter with power amplifier and cooling fan Vibration exciter SW 3009 Tightening torque: 21 Nm Insertion depth: 15 mm Power amplifier TGA 6014 3 x 380V / 50Hz / 35A / 23 kVA Condition: used Lhedpfezdtbmex Adcjn Scope of delivery: (See image) (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have over the phone. Written orders can be placed via email or fax.

Condition: used, FARO Measuring arm / 3D coordinate measuring arm FARO Prime measuring arm Mobile 3D measuring system / Portable CMM for industrial metrology For sale is a used FARO Prime measuring arm including accessories, transport case, and HP laptop. The measuring arm is suitable for mobile 3D measurements, quality control, component testing, reverse engineering, toolmaking, fixture construction, and industrial metrology. Technical data Manufacturer: FARO Technologies Type: Prime Device type: Portable 3D coordinate measuring arm / Portable CMM Date of manufacture: 10.09.2013 Calibration date according to certification: 25.06.2015 Revision: 28.1 Made in Switzerland Measuring range: approx. 1.8 m (6 ft) Axes: 6 Single point accuracy: 0.019 mm Volumetric accuracy: ±0.027 mm Repeatability: up to 0.016 mm Bluetooth wireless technology Integrated battery operation Temperature compensation Portable measuring arm technology USB interface Compatible with multiple probe systems Weight of measuring arm: approx. 9.3 kg Total weight including case and accessories: approx. 35 - 50 kg Equipment Mobile FARO Prime measuring arm Reference sphere / Calibration sphere Measuring probes / Probe set Base plate / Mounting plate Transport case HP EliteBook laptop Software data carrier USB dongle Operating instructions / Manuals Accessories according to pictures Application areas 3D coordinate measuring technology Quality assurance Incoming goods inspection First article inspection Component control Reverse engineering Tool and mold making Fixture construction Mechanical engineering Automotive industry Aerospace technology Condition Used Optical condition according to pictures Scope of delivery as shown in the pictures A complete technical function test has not been carried out Ledpfx Aezc Erpsdcohn Scope of delivery 1x FARO Prime measuring arm 1x Transport case 1x HP EliteBook laptop 1x Reference sphere 1x Base plate Measuring probes / Probe set Software data carrier USB dongle Documents and other accessories according to pictures The table shown in the photos, or other items not explicitly mentioned, are not part of the sale. Shipping or freight forwarding is possible. Subject to change, errors and prior sale. We are happy to answer any further questions by telephone.

Condition: used, Zwick / Roell Material Testing Machine / Universal Testing Machine Zwick / Roell Z020 Allround-Line BT2-FR020TNW.A50 20 kN material testing machine for tensile and compression testing with testControl II & testXpert V3.5 For sale is a used material testing machine from the manufacturer Zwick / Roell. The machine is suitable for tensile and compression tests on metals, plastics, elastomers, composite materials, and numerous other materials in the laboratory, quality assurance, research and development. Technical data: Manufacturer: Zwick / Roell Model series: Z020 Allround-Line Type: BT2-FR020TNW.A50 Testing force: 20 kN Testing direction: Tensile & Compression Testing space height: 1000 mm Crosshead speed: 0.0005–1000 mm/min Power connection: 230 V / 50–60 Hz Power consumption: 8 A Electronics: testControl II Software: Zwick / Roell testXpert V3.5 Equipment: Servo-electric material testing machine testControl II control system Industrial PC with installed testXpert V3.5 software 20 kN Xforce P load cell 2.5 kN Xforce P load cell Testing table Test fixture Various connection and cable sets Accessories as shown in the pictures Dimensions and weight: Machine dimensions (approx.): 1244 × 690 × 1324 mm (W × D × H) Weight: approx. 212 kg Application areas: Tensile testing Compression testing Material testing Quality assurance Research & Development Testing laboratory Education and training Lodszra Rqopfx Adcshn Scope of supply: 1 × Zwick / Roell Z020 Allround-Line material testing machine testControl II control system Industrial PC with installed testXpert V3.5 software 20 kN Xforce P load cell 2.5 kN Xforce P load cell Connection and cable sets Further accessories as shown in the pictures Condition: Used Visual condition as shown in the pictures Functional scope as shown in the pictures Nameplates are present The table, monitor, keyboard, and mouse shown in the photos, as well as any other items not explicitly mentioned, are not part of the sale. Shipping or freight forwarding possible. Subject to change, errors and prior sale. We will be happy to answer any further questions by telephone.

Condition: used, Zwick / Roell Type: BDO-FB0.5TH Zwick / Roell tensile testing machine, table-top testing machine Material testing machine BDO-FB0.5TH Testing load in tensile/compressive direction: 500 N Height: 1565 mm, Width: 292 mm, Depth: 469 mm Width of test area: infinite Test area depth: 100 mm Max. working distance without accessories: 1266 mm Lhsdpfx Aozdr Hnodcjn PC or printer interface: RS 232 Required PC connection (for PC operation): COM 1 Power data: 115/230 V (PH, N, PE) Rated power: 0.4 kVA Mains frequency: 50/60 Hz Weight: 47 kg Condition: used Scope of supply: (autosampler as shown in the picture) (Subject to changes and errors in the technical data; details are subject to change!) We will be happy to answer any further questions you may have by phone.

Condition: used, Renishaw Type: Equator 500 Year of manufacture: 2021 Item description: For sale is a Renishaw Equator™ 500, a high-precision, industrial 3D measuring and testing system for in-process and quality control in manufacturing. The Equator 500 is not a conventional coordinate measuring machine, but a comparative measuring system specifically designed for fast, repeatable measurements directly in the production environment. Ideal for serial production, in-process measurements, and automated inspection processes. The device is ideally suited for dimensional, form, and positional tolerance testing of workpieces and can be used to provide feedback to CNC machines. The software starts correctly, system status according to the display: "Started OK" (see photos). Functions & Applications 3D measurement of workpieces Comparative measuring principle (very fast inspection cycles) High repeatability in the µm range Real-time temperature compensation Suitable for shop floor use Automation capable (e.g. robot loading) Ideal for serial, sample, and process control Typical industries: CNC manufacturing Metalworking Automotive / supplier industry Machine and tool building Technical data (manufacturer's data / approximate values) Manufacturer: Renishaw Model: Equator™ 500 (H+150) Lhjdpjzix Nmsfx Adcen Device type: Comparative 3D measuring system / CMM Measuring range: X / Y: Ø approx. 500 mm Z: approx. 150 mm Measuring principle: Comparative coordinate measuring technology Temperature-compensated measurement Accuracy: Very high repeatability Measuring accuracy in the µm range (application and strategy dependent) Control & Software Controller type: Equator 500 Software version: 2.5.21.1 RRTLOS version: 5.1.12 Operation via PC-based Renishaw software Electrical data Supply voltage: 230 V AC Frequency: 50 / 60 Hz Power consumption: approx. 1 kW Dimensions (approx.) Overall height: approx. 1,900 mm Footprint / diameter: approx. 1,200 mm Weight (approx.) 130 kg Condition: used Scope of delivery: (See image) Renishaw Equator™ 500 measuring system Controller / Industrial PC Monitor Keyboard and mouse Base frame Accessories as shown in the photos (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: used, Zwick / Roell Type: Z020 Allround-Line BT1-FR020TN.A50 Zwick / Roell Material Testing Machine, 20 kN, Tensile & Compression Testing, testXpert III For sale is a high-quality Zwick / Roell material testing machine for professional tensile and compression testing of materials and components. The machine is suitable for metals, plastics, rubber, and many other materials and is typically used in laboratories, quality assurance, research, and education. The machine is controlled via a PC with Zwick/Roell testXpert III software (storage medium and documentation available). Technical Data: Nominal testing force: 20 kN Testing direction: Tensile & Compression Power connection: 230 V / 50–60 Hz / 1-phase Power consumption: approx. 2.1 kVA Weight: approx. 150–180 kg Dimensions: approx. 856 × 650 × 1,545–2,114 mm Technical Data (from documents & nameplate) Mechanics / Testing Nominal force: 20 kN Testing direction: Tensile & Compression Max. testing frequency: 0.5 Hz Crosshead: servo-electric Positioning accuracy: < 1 µm Speed range: 0.0005 – 1,000 mm/min Dimensions & Weight Overall height: approx. 1,545 – 2,114 mm (depending on the crosshead position) Overall width: approx. 856 mm Overall depth: approx. 650 mm Working space width: 440 mm Weight: approx. 150 kg (basic unit) approx. 180 kg with typical equipment Electrical Data Power connection: 230 V AC Lhedezimgtjpfx Adcjn Phases: 1-phase (1PH, N, PE) Mains frequency: 50 / 60 Hz Current consumption: approx. 8–10 A Power consumption: approx. 2.1 kVA Socket: Schuko (CEE 7) Measuring & Control Electronics Internal measurement value acquisition: 500 Hz Data transmission to PC: 10–100 Hz adjustable Interface: RS232 (COM) Protection class for electronics housing: IP32 Important note: “The table shown in the photos is not included in the sale.” Condition: used Scope of supply: (See picture) Zwick / Roell material testing machine (20 kN) Electronics unit PC workstation (monitor, PC condition see pictures) 2 measuring modules (Delock units) Zwick/Roell testXpert III software (storage medium) Original operating and technical documentation Various connection and linking cables (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have by phone.

Condition: used, Spectro Type: SpectroMaxX LMD08 / LMX08 Date: 07/24/2020 Complete analysis using the stationary spark optical emission spectrometer SpectroMaxX: Using the spark optical emission spectrometer, the alloy compositions and trace elements of macroscopic solid samples can be determined with high accuracy, down to the ppm range. Description of the system: Open spark stand for high sample throughput Lhodpfxjzizdte Adcen A wide variety of sample geometries are possible The following elements are available as a basis: Magnesium The analyzable elements and concentration ranges depend on the methods available for the respective base element. Usable wavelength range: 170-670 nm Output of measurement values in concentrations or intensities Selectable output units (%, ppm) Output of statistical parameters (mean, RSD) SPECTROMAXx LMX08 Technical specifications: CCD optics: High-resolution CCD multi-detectors Stabilized against temperature fluctuations Effective wavelength range: 140-670 nm; the applicable and configured wavelength range depends on the customer's application requirements. Automated profiling Analysis modules: Freely selectable analysis modules Optimized for customer requirements Expansion with additional modules possible on-site Spark stand: Open spark stand for high sample throughput and various sample geometries Minimized argon consumption due to the argon-saving module Optimized argon flow Reduced cleaning intervals Spark stand plate easily replaceable Temperature-absorbing design without water cooling Integrated shutter system for optimal plasma view Excitation system: Fully digitized plasma generator with digital discharge definition, digital pulse generation, and digital offline pulse control 32 MHz microcontroller Max. spark duration: 4000 µs Max. spark power: 4 kW Display system: Dedicated microcontroller for each CCD Serial source interface Spectrometer: External, state-of-the-art computer PC system with Windows operating system Keyboard and mouse Monitoring Software: Spark Analyzer Pro MAX software for analytical operation and calibration Continuous automatic hardware diagnostics in the background Automatic verification and identification of alloy/grade Result Manager Online maintenance scheduler Environmental conditions: Room temperature: 10-30°C Conditions: (10-30°C) Relative humidity: