Center lathe

ZMM CU800

Condition: new, neu Bulgarien 109100 € 2061.99 € 890 mm 3000 mm 400 mm 155 mm 490 mm 700 mm 15 160 M 24 160 0.032 - 38.9 mm/U 0.016 - 19.45 mm/U 0.5 - 480 mm 60 - 1/16 Gänge/" 525 mm 270 mm 125 mm 6 MK 260 mm 22 kW 7500 kg driven by manual transmission 3-axes digital readout quick change toolpostAmestra with 4 holders (3 square, 1 round) 3-jaw chuck Bison 3204/DIN6350, Ø 500 mm spindle dead center coolant equipment full length rear splash guard leadscrew and shaft protection safety guard for the chuck toolholder guard levelling bolts and plates tailstock quill reducer electric motor movement of tailstock low voltage machine lamp operating manual machine according to "CE" FURTHER TURNING LENGTHS: turning length1.500 mm € 94 720,00 turning length2.000 mm € 98 220,00 turning length4.000 mm € 117 110,00 turning length5.000 mm € 128 100,00 Rodpowirxqjfx Af Uop turning length6.000 mm € 144 630,00

Condition: used, Technical details: travel -y axis: Schlitten auf Balken: 200 mm spindle taper ISO: SK 40 spindle head swivable left - right: je 90° ° quill stroke: 80 mm turning speed range: 90 - 900 / 5 step U/min distance table - lower edge spindle: min./max.: 50 / 400 mm table surface area: Anbaufläche:760 x 200 mm table surface area: Spannfläche: 630 x 200 mm max. table load: 100 kg x-travel: Tisch längs: 320 mm z-travel: Tisch vertical 350 mm table swivelabel +/-: re/li je 30° distance table - lower edge spindle: min./max.: 50 / 400 mm feed:: Tisch: stufenlos 14 - 71 mm/min total power requirement: 4,0 kW weight approx.: 1.200 kg dimension machine xH: 1,3 x 1,5 x 1,8 m Equipped with Heidenhain DRO for X and Y travel Swiveling work spindle The feed works via variator gear. The table is swivelable. Rjdpfeu Ndb Ajx Af Uop Spindle speeds operate in 3 levels via gears and in 2 levels electrically. Cooling device diverse tool holders SK40 Der Fräsbalken ist um ca. 350mm ausfahrbar. The machine vise is not included in the delivery scope (see picture), but can be purchased additional! *

Condition: new, Technical data: Capacity: 160 t Installation height: 1100 mm Max. working area: 1100 x 350 mm Ram stroke: 400 mm Advance speed: 6.2 mm/s Return speed: 6.8 mm/s Motor power: 5.5 kW Redpfx Ask Nz Ntjf Uop Width: 1640 mm Depth: 1000 mm Height: 2550 mm Weight, approx.: 1300 kg Equipment: - Laterally adjustable cylinder via rack, pinion, and handwheel - Spacious working area - Height-adjustable table - Torsion-resistant design with welded steel construction - Manometer - Fine pressure adjustment - Additional hand pump Support prisms available at extra cost.

Condition: used, plate width 6400 mm Redpfsgrm Ngsx Af Ujp plate depth 1870 mm plate height 400 mm

Condition: new, pressure: 150stroke: 300column width: 1570working speed: 5retracting speed: 10Workshop Press: Steel welded construction Any stop position Pressure gauge Safety valve against overload 2 V-prisms Height-adjustable table Table up/down device Control with operating lever Equipment according to CE regulations, operating manual in German (Sample photo) Specifications: Press force: 150 tons Motor power: 11 kW Stroke: 300 mm Clear distance between columns: 1,570 mm Piston Ø: 280 x 200 mm Feed speed: 9 mm/s Redpfsd Ab Ndjx Af Uop Working speed: 5 mm/s Return speed: 10 mm/s Length: 2,500 mm Width: 1,000 mm Height: 2,270 mm Weight: 2,100 kg

Condition: used, Year of construction: 1981, Technical details: x-travel: 400 mm y-travel: 420 mm z-travel: 380 mm table surface area: 710 x 400 mm max. table load: 120 kg range of revolution per miute: 45 - 2240 / 18 step U/min feed continuous: 6,3 - 600 / 2 steples mm/min Rjdpfeu Nc Hkjx Af Uop quill stroke vertical: 100 mm quill stroke: horizontal: 100 mm spindle taper: vertical/horizontal: SK 40/SK40 spindle head swivable left - right: 90 ° distance table/horizontal spindle: min./max.: 200 / 325 mm distance table/vertical head: min./max.: 150 / 730 mm total power requirement: 5,5 kW weight of the machine ca.: 1,95 kg machine dimensions LxWxH: 1,7 x 1,4 x 1,9 m dimensions electric cabinet: 850x500x1500 mm The milling machine is equipped with a 3-measuring path display. incl. machine feet and operating instructions *

Condition: used, functionality: fully functional, machine/vehicle number: 106341-11, Year of construction: 2005, overall weight: 8,000 kg, total height: 2,700 mm, total length: 5,660 mm, total width: 3,956 mm, The drilling method of the deep hole drilling machine is single-lip drill deep hole drilling. Drilling Unit Information: - Number of spindles: 1 - Infinitely variable spindle speed: 300 – 8000 rpm - Spindle drive power: 7.5 kW - Max. drilling depth: 800 mm - Drilling diameter min/max: 3 – 25 mm based on ST 60 - Max. twist drilling: 25 mm - Max. thread tapping: M24x3 - Milling material removal rate: 150 cm³/min Travel Paths: - X-axis travel: 800 mm - Y-axis travel: 400 mm - Z-axis travel: 630 mm - W-axis travel: 800 mm Travel Speed: - X-axis speed: 15,000 mm/min - Y-axis speed: 15,000 mm/min - Z-axis speed: 15,000 mm/min - W-axis speed: 15,000 mm/min Fluid Information: - Coolant supply: deep hole drilling oil - Tank capacity: 800 liters - 1x scraper belt chip conveyor - 1x hydraulic unit and pneumatic system/equipment - 1x submersible pump: Pumping capacity: 200 l/min - 1x low pressure pump: Pumping capacity: 100 l/min Pump drive: 1.7 kW Rodpfx Afew E H E Re Usp - 1x compact belt filter: Filtration capacity: 120 l/min for processing steel/non-ferrous metals - 1x radial piston pump with remote adjustment: Pumping capacity: 2 – 94 l/min Pump drive: 7.5 kW Spindle Unit: - Cartridge spindle design with drive housing and spindle drive with gearbox. Spindle bearing with precision angular contact ball bearings and lifetime grease lubrication. Milling and Drilling Spindle Unit: - For conventional machining - Spindle head with HSK 50 tool holder Drill Bush Holder: - Design as 2-position turret with electric swivel mechanism - Locating position via Hirth coupling - Turret head with fixtures for: Guide bushes for deep hole drilling Milling and drilling spindle unit for conventional machining Pickup Tool Changer: - For conventional tools and drill bushings - Disc magazine design with 20 stations including feed stroke Automatic Tool Changer for Deep Hole Drilling Tools: - Fixed ELB column magazine for at least 5 tools including automatic tool clamping for HSK holders Clamping Table with W-Axis and NC Rotary Table: - Length/width: 800 x 600 mm - Positioning accuracy: B-axis +/- 30" - Centric payload: 1,500 daN Workpiece Clamping Device: - 1x tailstock with manual clamping movement - 1x NC dividing unit (A-axis) with manually operated two-jaw chuck for workpiece clamping - 1x base plate for mounting and clamping drill bushings + supporting prisms Electrical Equipment Information: - 1x CNC control Sinumerik 840D (digital complete system), including PLC S7-300 Connection Data: - Operating voltage: 3AC 400V ±10% – Frequency: 50 Hz - Control voltage: 24 V DC - Total connected load: 25 kW

Condition: good (used), Steel Plate Length: 3800 mm Width: 1400 mm Thickness: 130 mm 17 T-slots T-slots dimensions: 42 x 27 mm x total height 40 mm External Slots spacing: 300 mm Internal Slots spacing: 200 mm Holes diameter: Ø 40 mm Weight: 5 T Redpju Szupefx Af Uep

Condition: new, neu ca. 4 Monate ab Auftragse Bulgarien 44400 € 848.04 € 500 mm 1500 mm Rodpfjwiq Rfjx Af Usp 250 mm 80 mm 0 mm 400 mm 8 80 M 21 20-2000 1/min 120 0.04 - 12 mm/U 0.02 - 6 mm/U 64 0.5 - 120 mm 60 - 1/4" Gänge/" 240 - 1 315 mm 1 mm 90 mm 5 MK 2 mm 7,5 kW 3100 mm 1250 mm 1400 mm 2820 kg driven by manual transmission 3-axes digital readout quick change toolpostAmestra with 4 holders (3 square, 1 round) 3-jaw chuck Bison 3204/DIN6350, Ø 250 mm spindle dead center longitudinal stop for 1 position coolant equipment full length rear splash guard leadscrew and shaft protection safety guard for the chuck toolholder guard levelling bolts and plates quick release tailstock low voltage machine lamp operating manual machine according to "CE" FURTHER TURNING LENGTHS: turning length1.000 mm € 43 420,00 turning length2.000 mm € 46 190,00 turning length3.000 mm € 50 840,00 turning length4.000 mm € 56 2,00 turning length5.000 mm € 71 400,00

Condition: good (used), Offer 25348 Technical Specifications: - Plate length approx. 5500 mm - Plate width approx. 2000 mm - Plate height approx. 350 mm Rjdjxu Evwopfx Af Uop - Thickness of top plate approx. 80 mm - 8 pcs. T-slots in table surface, length 5500 mm - Center distance between T-slots in table surface: 255 mm each - Center distance of T-slots from outer edge: 110 mm - T-slot width approx. 40 / 60 mm - T-slot depth approx. 62 mm - Required space: L 5600 x W 2020 x H 350 mm - Weight approx. 10,200 kg