Lathe 720 x 3800 mm

Meuser M-IV-S

Condition: ready for operation (used), Center width: approx. 1400mm, center height: approx. 550mm, spindle diameter: approx. 100mm, faceplate: 1000mm/820mm. Speed: 560rpm, lathe chuck: 400mm/320mm. Pjdpfx Aajr N Rhqshegg

Condition: ready for operation (used), Year of construction: 1995, Mostana 1M63 x 3000mm Gap Bed Centre Lathe Max’ distance between centres 3000mm Max’ swing Over Bed 700mm Max; swing over cross silde 350mm Max’ swing in gap 900mm Spindle Bore 105mm Spindle Speeds 10-1250 rpm Spindle Motor 15kW Cross slide travel 400mm Year 1995 Machine complete with: Pgodjwf Sfvopfx Aahsg Sony LH70 2 axis Digital Readout Interlocking chuck guard Taper turning through compound slide 500mm 4 jaw chuck 390mm 3 Point fixed steady Rapid power traverse 4 way tool post Change gears coolant For sale with *Jet Machinery Ltd* Jet Machinery Stock No: #78739 Machine Serial Number: 1688 Cost: £14,950.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Condition: ready for operation (used), machine/vehicle number: 5722, table mounting size: 190 x 710 mm table movement x: 390/360 mm table movement y: 150 mm Pgsdoflrg Tspfx Aahog table movement z: 280 mm spindle taper: SK 40 spindle turning speed range: 100 - 3100 rpm carriages longitudinal: 0 - 600 mm/min electrical connection: 380 V, ca. 1,5 kW space needed: 1400 x 1200 x 1500 mm weight: ca. 680 kg

Condition: good (used), Year of construction: 1994, functionality: fully functional, feed length X-axis: 1,050 mm, feed length Y-axis: 360 mm, feed length Z-axis: 500 mm, travel distance X-axis: 1,050 mm, travel distance Y-axis: 360 mm, travel distance Z-axis: 500 mm, overall weight: 3,000 kg, Equipment: documentation/manual, Tiger FO 135 universal milling machine Description of the machine The machine was purchased new in 1994 and has only been in operation for a few hours. The milling machine is fully functional. The axis movements are smooth and the guides are in good condition. good condition. These have an automatic lubrication system. The table is in good condition and shows hardly any signs of wear. The machine also has a digital readout for the 3 axes, which makes it possible to work with cutter compensation and recurring measurement machining. Operating instructions are included with both the machine and the digital indicator. Technical specifications - Table dimensions 1,400 x 340 mm, 4 T-slots - Automatic traverse path: ➢ Longitudinal X 1,050 mm ➢ Transverse Y 360 mm ➢ Vertical Z 500 mm - Fixing the spindle cone: ➢ Vertical axis ISO 40, automatic locking ➢ Horizontal axis ISO 40, manual locking - Spindle speed range: ➢ Vertical axis 33 ÷ 1,560 rpm, 12 speeds ➢ Horizontal axis 35 ÷ 1,550 rpm, 12 speeds - Installed power: Podpfx Aasrqwbijhegg ➢ 5 kW vertical spindle motor ➢ 7.5 kW horizontal spindle motor ➢ Direct current motor 15 Nm - Variable power supplies Continuous speed 0 ÷ 1,500 mm/min - Fast feed ➢ Lengthwise and crosswise 3,000 mm/min Vertical 1,500 mm/min - Universal head with manual shaft lowering of 80 mm - Automatic lubrication with pump - Low-voltage electrical controls on the pushbutton panel of the side arm - Star/delta start - Magnetic thermal protection from Siemens - Net weight 3,000 kg - Machine dimensions (for transportation) ➢ Width 2,300 mm ➢ Depth 2,900 mm ➢ Height 2,400 mm Accessories - Counter supports for cutting shaft - Cutting shaft ø32 mm Tiger FO 135 universal milling machine Description The machine was purchased new in 1994 and has only had a few hours of operation. The milling machine is fully functional. Axis movements are smooth and the guides are in good condition. These have an automatic lubrication system. The table is in good condition and shows hardly any signs of wear. The machine also has a DRO for the 3 axes, which offers the possibility of working with milling compensation and recurring measurement processing. Both the machine and the DRO come with operating instructions. Technical specifications - Table dimensions 1,400 x 340 mm, 4 T-slots - Automatic travel: ➢ Longitudinal X 1,050 mm ➢ Transverse Y 360 mm ➢ Vertical Z 500 mm - Fixing the spindle cone: ➢ Vertical axis ISO 40, automatic locking ➢ Horizontal axis ISO 40, manual locking - Spindle speed range: ➢ Vertical axis 33 ÷ 1,560 rpm, 12 speeds Horizontal axis 35 ÷ 1,550 rpm, 12 speeds - Installed services: ➢ 5 kW vertical spindle motor ➢ 7.5 kW horizontal spindle motor ➢ DC motor 15 Nm - Variable power supplies Continuous speed 0 ÷ 1,500 mm/min - Fast forward ➢ Longitudinal and transverse 3,000 mm/min ➢ vertical 1,500 mm/min - Universal head with manual shaft lowering of 80 mm - Automatic lubrication with pump - Low voltage electrical controls on side arm push button panel - Star/delta start - Magnetic thermal protection from Siemens - Net weight 3,000 kg - Dimensions of the machine (for transport) Width 2,300 mm ➢ Depth 2,900 mm ➢ Height 2,400 mm Accesories - Counter supports for cutting shaft - Cutting shaft ø32 mm

Condition: used, Year of construction: 1985, machine/vehicle number: 294, x-travel:400 mm y-travel:190 mm Pjdpfxjvcf Hpo Aahegg z-travel:310 mm table clamping surface:280 x 750 mm Reach of the vertical spindle:115-575 mm feed steps:16 feed range:11,2-355 mm/min tool taper:SK 40 speed steps :16 speeds::56-1800 min-1 total power requirement:2,2 kW dimensions of the machine ca.:1550 x 1250 x 2000 mm weight of the machine ca.:1200 kg

Condition: used, TECHNICAL DETAILS - maxi module to be cut : 1.5 [mm] - maxi diameter to be cut: 70 [mm] - maxi length to be cut: 100 [mm] - part maxi length: 200 [mm] - number of tooth mini to be cut: 3 - number of endless screw threads (special accessories): 1 - helix angle: 0-90[°] Pgjdpjuhbpljfx Aahjg - milling tool maxi diameter: 50 [mm] - 11 milling tool normal speeds - speed normal machine: 226 – 2100 [rpm] - power: 1.5 [kW] - net weight: 1035 [kg].

Condition: as good as new (ex-display), Year of construction: 2024, functionality: fully functional, travel distance X-axis: 600 mm, travel distance Y-axis: 480 mm, travel distance Z-axis: 310 mm, spindle speed (max.): 2,000 rpm, spindle speed (min.): 40 rpm, quill stroke: 120 mm, total height: 1,820 mm, total width: 1,780 mm, total length: 1,400 mm, table width: 500 mm, table length: 900 mm, workpiece weight (max.): 190 kg, distance table to spindle center: 390 mm, Equipment: documentation/manual, Table surface (angled table): 900 x 500 mm Max. Workpiece weight: 190 kg Travel X: 600 mm Travel Y: 450 mm Travel Z: 380 mm Quill travel Z1: 120 mm Speed range: 40 - 2000 rpm Gear stages: 18 Drive power: 3.75 kW Tool taper: SK 40 (DIN 69871A) Weight approx.: 1560 kg including extensive standard accessories, e.g: Work area cladding 3-axis digital readout CONTUR Pgsdjhu Rwfepfx Aaheg Hydraulic tool clamp for vertical spindle Tool holder SK 40, DIN 69871A, tightening bolt DIN 69872, incl. hydraulic unit Monitored spindle protection 3 conventional handwheels Complete electrical equipment for three-phase current 400 V, 50 Hz Ball screws for X, Y and Z axes Vertical milling head Fixed angle table 900 x 500 mm clamping surface Swivel device for vertical milling head LED machine light Protective bellows for the vertical and horizontal guideways guideways Automatic central lubrication for the axis and ball screws Coolant system with pump Set (4 pcs.) of bearing elements Including tool holder package consisting of: 1 x collet chuck ER40 7 x collets (Ø 6, 8, 10, 12, 16, 20, 25 mm)

Condition: used, Year of construction: 2002, turning diameter 630 mm turning length 3000 mm swing diameter over bed slide 480 mm turning speeds 9 - 1800 U/min spindle bore 83 mm tailstock quill taper MT 6 total power requirement 22 kW weight of the machine ca. 5400 kg dimensions of the machine ca. 5250 x 1900 x 1750 mm Features: - Digital display - 3-jaw chuck Ø315 mm ROTA-S PLUS - MULTI-FIX quick-change holder - Digital speed display - Coolant device - Rapid traverse longitudinal and horizontal - Steady rest - Live center - Lathe chuck guard - Chip guard - Machine light - Machine feet - Operating instructions Pgsdpfowz Rvlox Aahjg

Condition: good (used), max. wheel diameter 130 mm gear width 140 mm max. module 2,5 min. module 0,3 turning speeds 112 - 1000 U/min min. number of teeth 6 Pgodpfx Aaovpab Ishsg clamping length max. 150 mm total power requirement 3,5 kW weight of the machine ca. 2,1 t dimensions of the machine ca. 1,3 x 1,2 x 1,5 m

Condition: used, Year of construction: 1985, x-travel 485 mm y-travel 385 mm z-travel 380 mm table surface area 800 x 460 mm spindle taper SK 40 control CONTOUR 1 spindle turning speed range 50 - 2500 U/min feeds 10 - 1000 mm/min rapid traverse 2 m/min table load capacity 600 kg quill stroke 80 mm total power requirement 7,5 kW weight of the machine ca. 2,0 t dimensions 2,4 x 1,7 x 1,98 m Acc.: vertical head with hydr. tool clamping and quill retraction, solid table, coolant - movement of X/Y/Z also possible via handwheels - Pgodetqqllspfx Aaheg