Hydraulic Double-Column (Drawing) Press

Hidrobrasil Vulkanisierpresse

Condition: new, Year of construction: 2019, machine/vehicle number: DF0303, pressing force: 160 t, pressure:160 t distance between columns:700 mm stroke:400 mm Return Capacity:16 t Engine Output:15 kW Travel:400 mm :600 mm Ram plate:700 x 600 mm table height over floor:850 mm Table size:700 x 600 mm speed of forward flow:10 mm/sec Pressing speed:10 mm/sec :10 mm/sec Oil cooling (electric):1,5 kW (max) Oil Tank Capacity:300 l weight of the machine ca.:4,2 t dimensions:950 x 2440 x 2400 m ejector:30 x 30 mm ejector stroke:150 mm pressure of ejector:15 t ejector speed:25 mm/sec Ksdpfxofxyh Ro Abnjdi no. of ejector pins:1 Stück heating plates :550 x 500 mm :6800 ? :2400 ? :1200 ? :1200 ?

Year of construction: 1993, condition: good (used), Vulcanizing press of the company Wickert Maschinenbau GmbH Landau Year of construction: 1993 Machine-No. 2559 pressing force: 2800 kN heating plates: 500 x 500 mm heating: electric distance between plates: 200 mm control Siemens S5 OP17 (conversion to S7 feasible) Kodon Sm A Sspfx Abnodi incl. sliding table, vacuum pump, vacuum chamber, storage tank Good, used condition. With CE-marking.

Condition: as good as new (ex-display), Year of construction: 2023, pressing force: 120 t, Here are the technical data of the offered machine: Technical data + information: HB 2021-A-188, oil hydraulic double column press 120 T bottom piston heating press. - idle speed up to 40 mm/sec - Opening speed up to 40 mm/sec - Starting press speed 5-15 mm/sec - Table size/heating plate size 600 × 600 mm - ram size/heating plate size 600 × 600 mm - 2 heating plates, electrically heated, up to 250 degrees - as OPTION - total size approx. 2000 × 1000 × 2800 mm height - Oil temperature control - Automatic lubrication - Free positioning of the ram - SICK/LEUTZE light barriers 14,1 mm on front side - Circuit oil cooling - Pressure holding valve 0 to 1800 sec. - Rear monitored door - Pressure adjustment from 30 T to 120 T - Travel limitation either by pressure or position - Programming set-up mode, single stroke (adjustable via rotary switch) - Control panel permanently installed in cabinet wall - Two-hand operation - Machine body double painted - Signal light: red: alarm, yellow baking phase, green: ready - Heating plates with electric heating rods, up to max. 250 degrees Kjdpfx Aek S Dt Tobnodi - Assembly, commissioning, instruction against separate charge Thermally neutral 80 - 120 °C Number of operating sides 1 side Forces Pressing force max. 1,600 kN Free ripping force max. 200 kN Pressure build-up time closed die steel to steel Max. 8 sec. Dimensions Max. Opening width per compartment 200 mm Stroke and min. opening per compartment 400/200 mm Table height above floor, without heating pl. 850 mm Height above floor (overall height) approx. 2.800 mm Hall height min. 3,500 mm Parallel deviation at 20 °C +/- 0.1 mm Deflection Determined at max. clamping force with 70 % occupancy ≤ 0.2 mm/m Total weight of the press without operating materials approx. 9 to Accessories: 4 HEATING PLATES 500 × 400 mm, max. heating capacity Equipped with temperature sensor 300 degrees Speeds Fast closing with 15 mm sec. Pressing speed 10 mm sec. Sound pressure level, measured at 1.5 m height at the control panel according to DIN 45635-T16-KL3 max. 8 db(A) Number of pressing cylinders 1 pc. Operating pressure max. 240 bar Pressing pressure build-up time 4 sec. Pressure accuracy during pressing stroke +/- 5 bar Main pump BOSCHREXROTH gear pump approx. 48 L/min Oil volume approx. HLP 46 MW 300 liters Ambient temperature max. 40 °C Oil temperature max. 55 °C Automatic pressure readjustment after 5 % pressure loss Pressure stabilization for up to 1800 sec. Electrical system Main supply 400 V AC Control voltage Hydraulic pumps 24 V DC 24 V DC Frequency 50 Hz Connection hydraulic main motor 15 kW Total connection approx. without heating plates 19 kW ##### If the press does not exactly meet your requirements, please click to request an individual offer exactly according to your needs: Contact us for an individual offer HIDROBRASIL manufactures presses exactly according to your requirements at surprisingly low prices! Our great strength is special machine construction and press automation. We sell customized hydraulic presses, press brakes and impact shears at surprisingly low prices. For the hydraulics of the presses we mainly use components of leading European manufacturers.

Condition: like new (used), Year of construction: 2023, total height: 2,500 mm, table height: 900 mm, pressing speed: 8 mm/s, pressing force: 50 t, overall weight: 2,900 kg, operating pressure: 250 bar, ram plate width: 498 mm, table length: 522 mm, table width: 522 mm, type of input current: AC, power: 10 kW (13.60 HP), input voltage: 400 V, distance table to ram: 600 mm, oil tank capacity: 130 l, operating speed: 8 mm/s, Equipment: safety light barrier, If the press does not exactly match your requirements profile, please click here to request a customized offer tailored to your needs: Contact us for a customized quote Hidrobrasil manufactures presses to your exact specifications at surprisingly competitive prices! #### 50 T top ram heating press, in double column design suitable for continuous shift operation, with these basic data: - With one heating level - Idle speed up to 10 mm/sec (adjustable via rotary control) - Opening speed up to 40 mm/sec - Starting pressing speed 8 mm/sec - Table size/heating plate size 522 mm deep, x522 mm wide - Plunger size/heating plate size 498 mm deep, x498mm wide - 2 heating plates, electrically heated, up to 200 degrees - Oil temperature monitoring - Circuit oil cooling on the hydraulics - Pressure maintenance valve 0 to 3600 sec - Pressure setting from 8 T to 50 T (50 T = 300 bar) - Travel limitation optionally via pressure or position - Two-hand operation, adjustable or fixed - Double-coated machine body - Signal light: red: alarm, yellow: baking phase, green: ready - Heating plates with electric heating rods, up to max. 200 degrees - Assembly, commissioning, instruction for a separate charge Kdedpjtwv S Nofx Abnei ### Technical data ## Type of construction - Press design: Double column press ## Thermally neutral - Temperature range: 80 - 120 °C ## Operating sides - Number of operating sides: 1 side ## Forces - Pressing force max.: 500 kN - Free tearing force max.: 20 kN - Pressure build-up time: Max. 3 sec. (closed tool steel on steel) ## Dimensions - Max. Opening width: 600 mm - Stroke and min. opening: 300/300 mm - Table height above floor with heating plate: 900 mm - Height above floor (overall height): approx. 2,500 mm - Hall height: min. 3,500 mm - Parallel deviation at 20 °C: +/- 0.1 mm - Deflection: < 0.2 mm/m (determined at max. clamping force with 70 % occupancy) - Total weight of the press without operating materials: approx. 2.9 t - Accessories: 2 heating platens (522 × 522 mm or 498 × 498 mm, max. heating capacity) - Heating platens equipped with temperature sensors: up to 200 degrees. ## Speeds - Fast closing: 10 mm/sec. - Max. pressing speed: 8 mm/sec. ## Sound pressure - Sound pressure level, measured at a height of 1.5 m at the control panel in accordance with DIN 45635-T16-KL3: max. 78 dB(A) ## Hydraulics - Number of press cylinders: 1 pc. - Max. operating pressure: 250 bar - Pressure build-up time: Max. 3 sec. - Pressure accuracy during the pressing stroke: +/- 5 bar - Main pump: BOSCHREXROTH gear pump, approx. 26 l/min - Oil volume: approx. 130 liters (HLP 46 MW) - Ambient temperature: max. 40 °C - Oil temperature: max. 55 °C - Flow temperature: not specified - Automatic pressure readjustment after 5% pressure loss - Pressure stabilization for up to 3600 sec ## Electrical system - Main supply: 400 V AC - Control voltage: 24 V DC - Frequency: 50 Hz - Hydraulic main motor connection: 7.5 kW - Total connection without heating plates: approx. 10 kW Description of the heating press: The Hidrobrasil heating press with a pressing force of 50 tons and a table size of 600x600mm is specially designed for industrial applications. It is an oil-hydraulic double column press equipped with a sliding table mounted on spring-loaded rollers. This press is ideal for a wide range of pressing processes as it works precisely and reliably.

Year of construction: 1990, condition: good (used), Vulcanizing press of the company Wickert Maschinenbau GmbH Landau Year of construction: 1990 Machine-No. 2559 Kdsdpsn Sm Aysfx Abnei pressing force: 2800 kN heating plates: 500 x 500 mm heating: electric distance between plates: 200 mm control Siemens S5 OP17 (conversion to S7 feasible) incl. sliding table, vacuum pump, vacuum chamber, storage tank Good, used condition. With CE-marking.

Condition: new, Year of construction: 2019, machine/vehicle number: DF0277-Rev06, pressing force: 10 t, pressure:10 t distance between columns:200 mm stroke:200 mm weight of the machine ca.:1,5 t dimensions of the machine ca.:2000 x 1420 x 760 m heating plates :660 x 210 mm :200 mm :200 mm Oil Tank Capacity:70 l Table Height:1100 mm :125 mm Kdjdpfx Absffamysnoi Ram Height:250 mm

Condition: new, machine/vehicle number: DF0238 - Rev.00, pressing force: 20 t, pressure:20 t passage width:400 mm stroke:300 mm Weight of machine approx.:3 t dimensions:2200 x 650 x 2540 mm power capacity:ca. 4,5 kW table plate:400 x 400 mm pestle plate:400 x 400 mm daylight:300 mm table height over floor:950 mm :2 - 20 t :S7 1500 Kdjdpfjfxyhbjx Abnoi

Condition: used, Year of construction: 1974, Vulcanizing Press Mapelli T60 Manufacturer: Mapelli Type: T60 Year of manufacture: 1974 Operating voltage: 380 V Frequency: 50 Hz Control panel: Integrated temperature controllers and operating modules Heating control: Three separately adjustable temperature zones Main switch: Present Manual/automatic operation: Selectable via control panel Safety features: Emergency stop Pressure display: Analog manometer Press area: Vertical closing unit with upper and lower heating plates Construction: Robust steel design Application: Vulcanizing and pressing of molded parts Ksdpfx Asx Exndebnsdi The Mapelli T60 vulcanizing press is a heavy-duty industrial press designed for reliable and uniform vulcanization processes. The robust housing made of solid steel ensures high stability and longevity. The clearly arranged control panel allows for precise adjustment of heating temperatures, operating modes, and pump functions. Three digital temperature controllers enable precise regulation of the heating plates, ensuring reproducible results during vulcanization. The vertical pressing mechanism offers a solid support and closing unit, ideal for molded parts and various materials. The machine features an integrated safety circuit including emergency stop, as well as an analog pressure gauge to monitor the pressing process. Due to its industrial design, the Mapelli T60 is excellently suited for continuous operation and offers an economical solution for companies requiring robust vulcanizing technology. No guarantee is given for the accuracy, completeness, or currentness of the information provided.

Year of construction: 2016, condition: ready for operation (used), This MAPLAN MFT 750/160 edition S was manufactured in 2016. It is a vertical injection moulding machine, ideal for precision plastic processing. Contact us for more information. Machine Benefits Technical Machine Benefits • Connected load: 84 kw • Nominal voltage: 3 x 400 v • Control voltage: 24 v • Safety distance: 310 mm Kdedpfjx U Tihjx Abnsi • Overrun time: 128 ms • Overtravel: 62. 3 mm • Max platform height: 750 mm • Platform dimensions: 1850 x 1300 mm • The systems are fully functional and were used in 2/3-shift operation between 2017 and 2022. • The spray cylinders were resealed and the insulation panels replaced in 2023. Extra Information Machine still under power

Condition: good (used), Year of construction: 1985, operating hours: 200 h, functionality: fully functional, overall weight: 5,200 kg, Equipment: documentation/manual, Vulcanizing presses, set of 2 machines Kdsdpfjx Hwt Isx Abnji