Year of construction: 2002, Condition: good (used), Functionality: fully functional, Exhaust air scrubber, gas scrubber, wet scrubber, exhaust fan Djljv Sitlsqxy Daokl 8 units in total Year of manufacture 2002 The systems only operated for approximately 3 years

Condition: repair required (used), Year of construction: 1992, 1992 Imeas Sheet Polishing Line Main Control Siemens S5 Simatic, electrical overhaul in 2017 Various Grades of Stainless Steel Pneumatic Sheet Loader (6m x 1m; 200kg capacity) RCS-2T/160 Satinatrice Twin Station Belt Polishing Unit (reconditioned 2018) SMS-2T/160 Twin Brushing Unit (2 new brushes) Plast/f/catrice PL/160 Film Application Unit Pneumatic Sheet Stacker and Run out Roller Table (6m x 1m; 200kg capacity) Take off Roller Conveyor Existing Protection Fencing around the Line Qty. of misc. Spares including chrome pressure roll for brushing unit, replacement polishing belts & brushes etc. Option of Large Dust Extraction fan set Min. Input Width [mm] 600 Max. Input Width [mm] 1500 Min. Output Width [mm] 600 Max. Output Width [mm] 1500 Min. Dkjlqxy Djwbubfeasl Thick. [mm] 0.4 Max. Thick. [mm] 3 Min. Length [mm] 1000 manual / 1250 auto Max. Length [mm] 6000 manual / 3000 Auto Coating foil Max line speed [m/min] 15 Burr (depending on Thickness) [%] EN 9445

Condition: excellent (used), Here we offer a used Datona mobile sandblasting unit. Datona mobile sandblasting unit DUO - 74 liters SKU DT-55212 Advantages and disadvantages: 2.5 m long hose for a long reach Easy to switch between blasting agents thanks to the mixing valve When using soda, the surface of the workpiece is not damaged Description: This mobile sandblasting machine is used for removing paint and rust. Thanks to the two boilers, you can choose from two different blasting media. The mobile sandblasting unit works with a pressure of 4 to 8 bar and requires a compressor with a suction capacity of at least 350 l/min. Double boiler: If blasting with soda or calcium carbonate does not achieve the desired result, simply try a different blasting agent. For a more effective effect, it is also possible to use both blasting agents at the same time. With the sandblaster, you have a practical machine in your home. With the help of the special mixing valve, you can use soda to easily and gently remove paint from steel, stainless steel, chrome, aluminum or polyester. A major advantage of blasting with fine soda is that the surface of the object to be of the object to be blasted is not damaged. You don't even have to remove rubber seals, chrome parts or glass. This saves a lot of time! The mobile sandblasting unit can be used both in the workshop as well as on site. Attention: The one boiler is only suitable for soda and calcium carbonate!!! ✓ Duo sandblasting unit ✓ 74 liter boiler capacity ✓ Air consumption is around 350 l/min Technical data: SKU DT-55212 Weight 33 kg Suitable blasting material Aluminum silicate Dato-Blast calcium carbonate soda Blasting cabinet connection 1/4" Max. Pressure 2 - 6 bar Minimum air consumption 350 l/min Min. compressor tank capacity 100 liters Type: DT-55212 Condition: gebraucht / used Deloqcuvwsqxy Dajkl Scope of delivery: (see picture) (Changes and errors in the technical data, specifications are reserved!) We will be happy to answer any further questions you may have on the phone.

Condition: used, Year of construction: 2010, Powder coating line from 2010, in excellent condition. Currently in use, available for inspection and testing. Maximum part size: L x W x H = 2600 x 400 x 1850 mm Equipment Technological conveyor Automatic speed V = 1.2 m/min Speed regulation from 0.5 to 2.5 m/min Preparation station MNA-3-LPG, total length 16.7 m Entry area: L = 2.5 m a. Washing, degreasing and phosphating: L = 3.6 m Number of spray frames – 10 Number of nozzles in the frame – 18 Total number of nozzles – 180 Pump capacity – 162 m³/h Pump power – 15 kW 4 m³ capacity for active liquid Internal heat exchanger with LPG burner – 160 kW Temperature – 50°C Mechanical oil separator Filtration system Dosing system with diaphragm pump and regulator Washing time – 3 min b. Drip zone L = 3.1 m Drip time – 2 min 30 sec c. First rinse L = 1.2 m Number of spray frames – 4 Number of nozzles in the frame – 18 Total number of nozzles – 64 Pump capacity – 38 m³/h Pump power – 3 kW 1.5 m³ water capacity Rinse time – 1 min d. Drip zone L = 3.1 m Drip time – 2 min 30 sec e. Fine rinse L = 1.28 m Number of spray frames – 3 Number of nozzles in the frame – 18 Total number of nozzles – 54 Pump capacity – 33 m³/h 1.5 m³ water capacity Pump power – 3 kW Additional spray frame Rinse time – 1 min f. Drip zone L = 2 m Drip duration – 1 min 40 sec Three connections for the extraction system with three fans Working zone made of stainless steel Pipes made of PVC or stainless steel 1 pc. Automatic dryer after washing AST-1-KLPG: Dimensions of the working zone L x W x H = 7000 x 3000 x 2800 mm Air curtains on each side to reduce heat loss Indirect heat exchanger, heated by LPG, 200 kW Three fans, air supply 6000 m³/h Two connections for the extraction system Temperature sensor and regulator Overheating sensor Circulation sensor Working zone made of galvanized steel Thermal insulation 200 mm thick Drying time – 10 min 1 pc. Automatic polymerization oven APT-2-KLPG Working area dimensions L x W x H = 10200 x 3600 x 2800 mm Air curtains on one side to reduce heat loss Two indirect heat exchangers heated by LPG, each 300 kW Eight circulation fans, each with a capacity of 6000 m³/h Two connections for the exhaust system Temperature sensor and regulator Overheating sensor Circulation sensor Working area made of galvanized steel Thermal insulation 200 mm thick Polymerization time – 25 min 1 pc. Overhead rail transportation system for ATR paint shop: Straight rail with hangers L = 400 mm – 146 m Drive station – 2 pcs. Tension station – 1 pc. Chain lubrication station – 1 pc. Dkslqxsv Ed Ukey Daol Rail support structure drawings – 1 set.

Condition: used, machine/vehicle number: 0940, without hall piping Dkelqxy Dorz Iq Hjaol

Condition: excellent (used), Year of construction: 2019, Functionality: fully functional, Double-sided component painting line fully automatic Dolqxyotut Dxs Daokl Working width of the line 1300 mm The line consists of the following devices: - Vacuum feeder - automatic feeder before painting - GIARDINA Dualtech 416 automatic paint machine - 2 x 12m hot air drying tunnel - UV dryer - 3 lamps - material turntable - automatic painting machine RICHFRUITS - 2 x 12m hot air drying tunnel - UV dryer - 3 lamps - Vacuum feeder Machine in working order, connected in very good condition.

Condition: good (used), Year of construction: 2022, Tray trolleys, paint drying trolleys, compartment transport trolleys, transport trolleys, tier trolleys, support arm trolleys -Manufacturer: Lübbers, heavy-duty paint drying car with 14 levels on both sides -Middle rake: laterally adjustable -Total length: 1580 mm -Total depth: 1430 mm / 2x 670 mm support -Total height: 2000 mm -Quantity: 1x transport trolleys available -Price per piece -Weight: 130 kg/pc. Dkjlqxjrzvwhoy Dasl

Condition: excellent (used), Functionality: fully functional, BMB TUA-200/2 coating system in top condition. Delqxy Dov I Tb Eeaokl Purchased: 2023 (as good as new) and in use for only 6 months. Version: Professional version (very good features) - High-speed coating up to 4x faster - 3 coating processes in one system - Suitable for components up to 1200x570mm - Permanent viscosity/temperature control - Full traceability (depending on version) - Tool recognition and parameterization - Maximum protection by coating the components with paint - (Digital work document system, under development) - Large paint tank volume for tall components - Paint consumption calculation - Innovative, robust, and proven technology With the BMB Traceability and PDM system (equipment under development), you can track at any time which component was produced when, where, by whom, and how. ISO/TS 16949 requirements are met. When setting up a tool, the PDM system automatically recognizes all the necessary coating parameters. Work instructions, videos, technical data sheets, processing instructions, etc. Everything in its place! 19" swiveling Smart Touch Panel Viscosity control Tool monitoring: Automatic detection and adjustment Machine electrically height-adjustable Coating processes: - DipCoat dip coating - Selective Contact Coating (SCC®) - Selective Transfer Coating (STC®) The system can be shipped by freight forwarder upon request. #8300

Year of construction: 2018, Condition: excellent (used), EFD Type: MINAC 6/10 SM Heat treatment The compact design of the Minac induction heating system allows for easy installation and offers fast, concentrated and controlled heating with full repeatability. repeatability. Medium frequency product line Technical data: Maximum output power 10 kW Continuous output power 6 kW Mains voltage 400-480 V Frequency range 10-25 kHz Control range of output power 2-100% Recommended back-up fuse 16 A Cooling water approx. 4 l/min Cooling water flow temperature min./max. 18 - 35°C Cooling water pressure min./max. 4 - 6 bar Djlqot Din Aexy Dajkl Weight approx. 50 kg Dimensions (WxDxH): 345 x 708 x 453 mm Year of construction: 2018 optris CTlaser infrared thermometer Abbreviation: 3ML Measuring range: 50 to 400 °C Spectral sensitivity: 2.3µm Typical application: Metals at low object temperatures (from 50°C) Temperature control ECU 1214C Hyfra eChilly water cooler 4-S Cooling capacity 4395W The device comes from the laboratory sector. Only a few operating hours. Condition: used Scope of delivery: (see picture) (Changes and errors in the technical data, specifications are reserved!) We will be happy to answer any further questions you may have on the phone.

Condition: good (used), Year of construction: 2016, The spray booth type KF SL3 produced by Kimel Filtri is for sale. Year of production and installation: 2016. Dkelqoirabqsxy Daol Dimensions of the paint shop: 4.5 x 3 x 2.8 m Dimensions of the drying space: 5 x 4.2 x 2.8 m Dry suction rock Supply of warm air via a gas thermogen. The paint shop is controlled by automatic parameters. The paint shop is currently in use, is in operation and can be tested. The paint shop is completely correct. Price on request.

Condition: new, Year of construction: 2024, Paint/spray booth dimensions without fan and control Panel! Extraction surface - dimensions (mm): 4430(w)x1900(h) Overall dimension(mm): 4530(w)x2350(h)x1910(d) Technical data: - Fan power 4.4kW (ATEX) - Fan suction capacity: 24000 m³/h (max 1200Pa) - Lighting: 2 pcs 2x58W (ATEX) - Connection voltage: 400V Dkjloia Taxjqxy Dajl - Frequency converter for smooth regulation of the fan - Three-stage air filtration - Intended for explosive environments - EX - Complete technical documentation - CE Documentation - Warranty Possibility to order machines in various individual configurations and dimensions! Do not hesitate to contact us

Condition: used, Technical details: machine weight approx.: auf Anfrage kg dimension machine xH: auf Anfrage m Surface measuring and recording device SP6 2x feeding device PRK 6720702 1x measuring stand PST-Ue ( transverse = 165mm and vertical adjustment = 440mm) table size 650 x 450mm 1x measuring stand PST-Ve (vertical adjustment 450mm, motorized) + manual control unit; table size 650 x 178mm Perthometer S6P Without base cabinet, without the granite plate shown in the picture. Can be offered separately. i.D. * Dksleu N Awvjqxy Dasl

Condition: good (used), Compressed air filter, fine filter, filter, pre-filter, intake air filter, air filter housing, air filter housing, generator air filter, compact filter, suspended matter filter -Air filter: stainless steel housing -Number: 2x air filters available Dkslqxjvxf S Doy Dajl -Price: per piece -Dimensions: 610/100/H305 mm -Weight: 7.2 kg/piece

Condition: good (used), Manufacturer: LIEBISCH Type: 42016001 Test chamber : 1000 liters Dkslqxspbv Dpjy Dajl

Condition: excellent (used), Kärcher Type: PC 60/130 T / with oil separator (skimmer) attachment kit Kärcher parts cleaner Manufacturing, maintenance, workshops, metal processing - automatic parts cleaners have many applications. The parts cleaners work on the basis of aqueous solutions without solvents. The top loader PC 60/130 T is a fully automatic parts cleaner for parts up to 600 mm in diameter, 310 mm in height and 130 kg maximum weight. The items to be washed are cleaned using three-dimensionally arranged flat jet nozzles using solvent-free, heated Kärcher water-based cleaning agents. The items to be washed rotate on an electrically driven rotating basket during cleaning. The Parts Cleaner PC 60/130 T offers numerous practical details such as an integrated small parts drawer that reliably catches loose parts and coarse dirt particles. Equipment: Operating hour meter Holding ring (stainless steel for turntable) Swivel castors, 2 lockable Dkslqxsfu Ikwjy Dajl Timer for cleaning cycle Water level control Oil separator (skimmer) attachment kit See Figure 7 The oil separator (skimmer) extends the service life of the cleaning solution considerably. If the cleaning solution has settled, for example overnight, the oil that has been added floats to the top. The skimmer can now be switched on to remove this oil from the cleaning solution. Specifications Technical data: Pressure (bar/MPa) 1.5 / 0.15 Flow rate (l/h) 4500 Connected load (kW) 5.5 Working diameter (mm) 600 Usable height (mm) 310 Housing / frame stainless steel (1.4301) Tested (by) according to CE Heating power (kW) 4.5 Max. temperature (°C) 80 Adjustable cleaning time (min) 1 / 30 Payload (kg) 130 Sound pressure level (dB(A)) 65 Tank capacity (l) 100 Number of current phases (Ph) 3 Frequency (Hz) 50 Voltage (V) 400 Dimensions (D x W x H) (mm) 1080 x 1000 x 1250 Very few operating hours as can be seen in the photo. Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data, information is subject to change!) We will be happy to answer any further questions you may have over the phone.

Condition: ready for operation (used), We offer 4 pieces of reconditioned Schlick turbines, 320 mm, including 7.5kW motors. The price listed is for 4 pieces complete. Price for 1 piece - 3000 Eur. Delqxy Djvphf Ueaekl

Condition: new, Year of construction: 2024, Paint/spray wall dimensions without fan and control Panel! Delqxyoia Ta Uj Daekl Extraction surface - dimensions (mm): 4430(w)x1900(h) Overall dimension(mm): 4530(w)x2350(h)x810(d) Technical data: - Fan power 4.4kW (ATEX) - Fan suction capacity: 24000 m³/h (max 1200Pa) - Connection voltage: 400V - Frequency converter for smooth regulation of the fan - Three-stage air filtration - Intended for explosive environments - EX - Complete technical documentation - CE Documentation - Warranty Possibility to order machines in various individual configurations and dimensions! Do not hesitate to contact us

Condition: new, As a leading manufacturer of systems for surface technology, we offer you an almost limitless portfolio for powder coating applications. At our site in 47669 Wachtendonk, we turn your individual requirements into reality and produce your desired concept. Thanks to our in-house production for almost all components, we are flexible and can respond specifically to your requirements. We not only provide you with your ideal powder coating system - we are also on hand with comprehensive user expertise to support you in all matters relating to surface technology. Every item offered here is manufactured especially for you. Whether large or small projects - we supply complete systems from a single source, tailored to your requirements. We look forward to hearing from you and implementing your ideas together! Here we offer: Doljuqygvoqxy Daskl -lift/lowering stations for one or more rails (also available with end control lighting) -Manual or electric cross travel platforms -Combi-device cross travel platform with lifting/lowering function -Complete transport system incl. parking bays, goods carriers -Power and Free transport systems Manual or automatic, chain-driven rotation -Planning, design and assembly included Take your powder coating to the next level of efficiency - we support you with the ideal planning and implementation.

Condition: new, Functionality: fully functional, Year of construction: 2025, Aluminum Aging Furnace is the furnace where the precipitation hardening, i.e. aging process, of the aluminum profiles drawn in the extrusion line is performed. Aluminum thermalization furnaces harden the porous structure of aluminum by subjecting the profiles kept between the specified temperature and time periods to the aging process. As HAS MAKİNA POWDER PAINTING SYSTEMS, we design and manufacture furnace production in various sizes and capacities in accordance with the demand and intended use within the necessary engineering calculations for our valued customers. Delqxsv Nkipoy Daskl Profile Thermalization Furnace, Aluminum Thermalization Furnace, Thermal oven, Aluminum aging furnace, Profile thermalization furnace,

Condition: good (used), Year of construction: 2005, This is a programmable sandblasting machine with a working area of 100x100mm. Dkolqev Rcycjxy Dasl Includes documentation and instructions. The machine dimensions are: WxDxH - 1300x700x1750

Condition: ready for operation (used), Year of construction: 2010, Bürkle LFC 2100 roller coater for painting rigid materials The machine is functional and has signs of use appropriate to its age. The application roller was re-rubbered in 2022, since then the roller has hardly been used (still as good as new). The drive roller and conveyor belt have also been replaced. A viewing and a paint test are of course possible by arrangement. Dkjlqxy Dovxr Dyjaol Dismantling and transport of the line is organized and borne by the buyer. Any questions or further details are welcome by phone or email.

Condition: new, Year of construction: 2025, Functionality: fully functional, Our SAPI Blasting Halls SAPI sandblasting halls and systems with 50 years of tradition and proven quality. Sandblasting halls are designed for industrial and commercial use, providing a safe environment for all types of blasting work. They include a blasting room, an abrasive recovery system with a filter and dust extraction system, lighting, and safety features to ensure the safety of the operator. Recovery System Our recovery system collects, separates, and reuses the abrasive material, which reduces costs and environmental impact. Ventilation and filtration systems ensure that the air in the hall remains clean. Adequate lighting ensures optimal visibility for the operator. Key Components of Our SAPI Sandblasting Halls: ✅ Blasting Room: The central area where the actual sandblasting takes place. 🌬️ Ventilation and Filtration Systems: Reduce dust levels and ensure optimal visibility. 🔄 SAPI Recovery System: Recycles the abrasive material and reduces costs and environmental impact. 💡 Lighting: Ensures optimal visibility for safe operation. 🦺 Safety Features: Emergency shutdown, fire protection, and protective gear like helmets, overalls, and gloves. ⚙️ Control Panel: The control center that integrates all electrical components. 🗑️ Dust Collection Container: Collects fine abrasive material for easy disposal. 🛠️ Compressor: Powerful compressor for the compressed air supply. 💪 Mammut Sandblasting System: Designed for tough industrial use. Reasons to Choose Our Sandblasting Halls: ✅ High Efficiency: Increases productivity and reduces operating costs. 🛡️ Safe and Clean Environment: Minimizes environmental impact and ensures a safe working environment. ⚙️ Customizable Solutions: Tailored solutions for optimal performance. 🔧 High-Quality Components: Durable components that reduce maintenance needs. 🛠️ Support and Service: Expert support for quick problem-solving. Dslsun R N Aoqxy Dajkl 🌱 Environmental Responsibility: Reduces waste and environmental impact. The SAPI Flat Conveyor System: The abrasive material is processed by our efficient abrasive cleaner, which separates contaminants. The system is low-maintenance, operates without interruption, and consumes very little energy. It is easy to retrofit and can be installed on existing hall floors with minimal foundation work. Advantages of Our Flat Conveyor System: ✅ Low installation depth, retrofit-compatible with existing blasting rooms 🔇 Low noise and friction ⚡ Very low energy consumption 🏗️ Very low wear, as only rubber is used 🚧 Very low installation height

Condition: new, Year of construction: 2024, dimensions without fan and control Panel! Work space size - 2x dimensions (mm): 1180(w)x1190(h)x750(h) Overall dimensions (mm): 2500(w)x2150(h)x1000h) Delqxy Djibcxqsaskl Technical data: - Fan power 2x0.75Kw (ATEX) - Fan suction capacity: 2x4500 m³/h (max 900Pa) - Connection voltage: 400V - Frequency converter for smooth regulation of the fan - Three-stage air filtration - Intended for explosive environments - EX - Complete technical documentation - CE Documentation - Warranty Possibility to order machines in various individual configurations and dimensions contact us

Condition: new, Functionality: fully functional, Pretreatment system for wet chemical cleaning of workpieces to be coated - NEW - As a leading manufacturer of systems for surface technology, we offer you an almost limitless portfolio for powder coating applications. At our location in 47669 Wachtendonk, we put your individual needs into practice and produce your desired concept. Thanks to our own production for almost all components, we are flexible and can respond specifically to your requirements. With us, you not only get your ideal powder coating system - we also have comprehensive user expertise at your side to support you with all questions about surface technology. Every item offered here is manufactured especially for you. Regardless of whether it is a large or small project - we supply complete systems from a single source, according to your ideas. We look forward to hearing from you and implementing your ideas together! Here we offer you our newly manufactured VBH KM Pro pretreatment system for part dimensions of up to 4,000x1,400x2,000mm. System description: Pretreatment system for wet-chemical cleaning of workpieces before coating using the 3-zone process + nozzle line for loss. Equipment: -Washing stations for up to 2 traverses in one cleaning cycle -3 rails (1 middle, 2 side washing stations) -Washing ring with removable middle nozzle line (Info: The middle nozzle line is used when 2 rails with flat workpieces are to be cleaned at the same time; without the middle nozzle line, wider workpieces can be moved in and cleaned on the middle guide rail.) -4 washing zones (degreasing circuit, 1st rinse (pre-rinse) circuit, 2nd rinse (final rinse) demineralized water cascading to degreasing basin 1 -final spray ring (zone 4) for passivation in the no-rinse process when pulling out the goods carriers (duration of fogging adjustable) Passivation is injected into demineralized water. Inlet in basin 1. Dkjlotxcyioqxy Dasl -2 storage containers made of stainless steel including level monitoring (sink 1 + demineralized sink) -1 stainless steel container insulated, as electrically heated, including level monitoring (degreasing) -Drain taps on the basins for disposal, cleaning and new preparation -Supply of the VE water requirement via mixed bed cartridges -Exhaust fan to remove the water vapor to the outside including exhaust pipe -Cabin made of stainless steel -Loading via double-wing door -Operating terminal (PLC controlled) outside the washing cabin -Control via PLC and touch display including remote maintenance module -Intuitive, illustrated operation for quick and easy handling Suitability: -particularly for flat workpieces, as the use of the central line means 2 product carriers can be cleaned at the same time -Frames and uncomplicated, open geometries up to a maximum of 1,000 mm wide can also be cleaned well Advantages: -Personnel-free, automatic cleaning, within approx. 20 minutes. -optimal adhesion properties especially for the subsequent coating -fully parameterizable process program from KM Industrieservice, thus completely flexible for changed chemical systems -lifetime support and spare parts availability from KM Industrieservice -cost-effective pretreatment solution with service life-optimized tank quality, thus also cost-effective wastewater disposal We can send you a video link to this system on request.

Condition: new, Year of construction: 2025, Functionality: fully functional, Powder Coating Plant With Conveyor Our experienced team prepares powder coating plant in special design and special sizes for each project. Please contact us for detailed information Conveyor system A conveyor system is a common piece of mechanical handling equipment that moves materials from one location to another. Conveyors are especially useful in applications involving the transport of heavy or bulky materials. Conveyor systems allow quick and efficient transport for a wide variety of materials, which make them very popular in the material handling and packaging industries. They also have popular consumer applications, as they are often found in supermarkets and airports, constituting the final leg of item/ bag delivery to customers. Many kinds of conveying systems are available and are used according to the various needs of different industries. There are chain conveyors (floor and overhead) as well. Chain conveyors consist of enclosed tracks, I-Beam, towline, power & free, and hand pushed trolleys Dslqxy Dov Nv Dfsaokl