Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. Hfsdpfx Ajwzl Hxjbnjd * FLASH-OFF PROCESS: After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Electrical devices and control panels: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: PEF-2.5 PULVER EINBRENNOFEN ELEKTRISCH, temperature: 230 °C, heating capacity: 30 kW (40.79 HP), inner dimension length: 2,500 mm, inner dimension width: 1,505 mm, ✈️ Plus shipping costs – Shipping available upon request.✈️ Fast delivery: Only 6 weeks after receipt of payment! ✅✅✅Energy Class A+++✅✅✅ ✅ Plug & Play system – Delivered fully assembled, ready to use immediately! ✳️ Maintain your liquidity! We offer a variety of financing options to ensure your investment has the best chance of success. Contact us today to learn more about our hire purchase, warranty, or leasing programs. ☘️Environmentally friendly☘️⚡️Green energy⚡️☘️ ⭐ Powder furnace with electric heating - ✔️ Internal dimensions: 2500 mm L * 1505 mm W * 1800 mm H ✔️ Electric heating output: 30 kW/h ✔️ Fan: 3000 m3/h 80 mm SS ✔️ Circulation fan output: 1.5 kW/h ✔️ Total 35 kW/h +- 10% ✔️ Digital heat control, continuously adjustable temperature up to 220°C ✔️ Sandwich panels inside: 1.5 mm galvanized steel, outside: 1.5 mm powder-coated Steel ✔️ Adjustable curing temperature, curing time, and exhaust fan function ✔️ An audible signal sounds at the end of the curing time ✔️ Insulated door with special locking systems (snap lock) ✔️ Insulation: 150 mm (150 mm rock wool) 🔥 PEF-2.5 Curing Oven: Your versatile industrial oven for drying and curing processes! 🔥 Whether powder coating, wet paint, plastic processing, or other thermal processes – the powder curing oven is your reliable solution for professional curing and drying processes up to 230°C! 🌡️ _____ 🚚 Maximum loading flexibility • Compatible with ceiling rail systems • Optionally with insert shelf system for small batches _____ ⚙️ Intelligent control – just the way you need it ✅ PID control (optional) for precise temperature control ✅ Touchscreen control panel & smartphone control 📱 (optional) Hfedpfxewfgbrs Abnjd ✅ Weekly & monthly reports at the touch of a button (optional) ✅ Timer function: freely programmable from 10 minutes to 24 hours ⏲️ ✅ Automatic shutdown after the end of the process _____ ♨️ Ramp heating mode (optional) Precisely control temperature progression and holding times, e.g. E.g.: • Reach target temperature within a defined time • Maintain desired time • Controlled cooling to target temperature • Automatic notifications of process events _____ 🛡️ Safety is our priority 🟢 Safety sensors to prevent overheating 🟢 Automatic shutdown in the event of a fault 🟢 Acoustic warning signals in the event of errors 🟢 Solvent and fume removal via automatic venting _____ ⚡ Customized energy and heating system 🔥 Also available with an extension up to 400°C for high-temperature processes (optional) _____ 🧠 No repeated settings necessary! The furnace saves your process parameters – batch by batch. This saves you time and avoids errors. _____ 📢 And best of all: If you have special requirements – we also build customized furnaces according to your specifications! Contact our team of experts for a personalized consultation! _____ ☀️ 2-YEAR WARRANTY ☀️ Request more information

Condition: new, Year of construction: 2026, functionality: fully functional, CONVEYOR BELT TUNNEL WASHING MACHINE - The components to be clean are carried on a continuos moving stainless steel belt conveyor or a stop and go pallet conveyor. The design transfer time/speed and the tunnel dimensions are design in accordance to customer’s cycle time and production need. The synergy between chemical, thermal and mechanicals actions, enable to create an accurate and high efficient washing removing all contaminants from the components with excellent cleaning results. Hodjwdfnzopfx Abnjfd The tunnel can be easily inspected thanks to doors installed along the tunnel in correspondence with each active station, the pumping system and filtering devices through stainless steel spray manifolds achieve maximum treatment accuracy and efficiency with stainless steel nozzles of suitable capacity. The spray pressure is controlled by pressure gauges and in regulated by ball valves.

Condition: as good as new (ex-display), Year of construction: 2026, Parts Cleaning Machine / Combination Spray Cleaning System Type L101 HP automatically working hot water parts washer with basket drive by means of gear motor, stainless steel washing pump (Lowara), spray system with stainless steel nozzles additional manual cleaning with high pressure nozzle (60 bar) and foot switch, air blow-off gun, large viewing window with gauntlet gloves, LED interior lighting - Basket diameter: 910 mm - useful height: 490 mm - max. loading weight: 200 kg Hjdpfsd R Ahlox Abnofd - Spray pressure (washing pump): 2.3 bar - spraying pressure (HD pump): adjustable up to max. 60 bar - tank volume: 175 litres - Heating: electrically adjustable (RT - 60°C) - plant dimensions (LxWxH): 1.300 x 1.500 x 2.100h mm - empty weight: approx. 200 kg ++washing time clock freely adjustable (minutes and hours) ++complete cleaning machine (interior and exterior cladding) made of ++stainless steel 1.4301 ++Water circulation and loading basket made of stainless steel 1.4301 ++Bath cover with fine filter (2.000 micron) ++Operating hours counter ++Steam vapour extraction incl. condensate recirculation ++Omron timer for setting the time in sec./min./hour. Parts washer is as good as new (test plant/technical centre); Year of construction: July/2021 OTHER BASKET DIMENSIONS AVAILABLE ON REQUEST !!!

Condition: used, Year of construction: 1999, 1999 CM System D8 Overhead conveyor (painting chain) for handling chairs or similar products, dyed on hooks. 80 linear meters. Towing group: lightweight Caterpillar engine Working speed: min/max 0:9 m/min Motor power: HP 2 D8 chain development and d. 37 rollers: 80 meters Straight track to measure: 72 meters 90° horizontal bends r= 500 mm: 10 pieces Hook step: 0.80 m Space required for transport: 5 meters free on truck Hedpfxjxyi Uuj Abnefd

Condition: used, Year of construction: 1999, 1999 CM System D8 Overhead conveyor (painting chain) for handling chairs or similar products, dyed on hooks. 600 linear meters. Complete system with 2 rotating disc cups, electrical panels, hooks, various equipment as shown in the photo. Hfjdpfx Asxywniobnod Towing group: n.2 medium-sized Caterpillar motorized groups Working speed: min/max 0:9 m/min Motor power: HP 2 + HP 2 D8 chain development and d. 37 rollers: 600 meters Straight track to measure: 531 meters 90° horizontal bends r= 500 mm: 91 pieces Horizontal curves at 30° r=500: 6 pieces 30° vertical curves r=500: 26 pieces Hook step: 0.80 m

Condition: good (used), functionality: fully functional, 2 Waxing Machines for stone slabs Hfodpfxjxxlm Dj Abnod

Condition: new, Year of construction: 2026, functionality: fully functional, type of input current: three-phase, warranty duration: 12 months, Paint/spray wall dimensions without fan and control Panel! Extraction surface - dimensions (mm): 4430(w)x1900(h) Overall dimension(mm): 4530(w)x2350(h)x810(d) Technical data: - Fan power 4.4kW (ATEX) - Fan suction capacity: 24000 m³/h (max 1200Pa) - Connection voltage: 400V - Frequency converter for smooth regulation of the fan - Three-stage air filtration - Intended for explosive environments - EX - Complete technical documentation - CE Documentation Hsdsia Ta Uopfx Abnsfd - Warranty Possibility to order machines in various individual configurations and dimensions! Do not hesitate to contact us

Condition: new, Year of construction: 2026, functionality: fully functional, type of input current: three-phase, warranty duration: 12 months, Equipment: cabin, Paint/spray booth dimensions without fan and control Panel! Extraction surface - dimensions (mm): 4430(w)x1900(h) Overall dimension(mm): 4530(w)x2350(h)x1910(d) Technical data: - Fan power 4.4kW (ATEX) - Fan suction capacity: 24000 m³/h (max 1200Pa) - Lighting: 2 pcs 2x58W (ATEX) - Connection voltage: 400V - Frequency converter for smooth regulation of the fan - Three-stage air filtration - Intended for explosive environments - EX - Complete technical documentation - CE Documentation Hfedsia Taxepfx Abnod - Warranty Possibility to order machines in various individual configurations and dimensions! Do not hesitate to contact us

Condition: new, Year of construction: 2026, functionality: fully functional, type of input current: three-phase, warranty duration: 12 months, Equipment: cabin, lighting, Paint/spray booth dimensions without fan and control Panel! Extraction surface - dimensions (mm): 1600(w)x1900(h) Overall dimension(mm): 1700(w)x2350(h)x1910(d) Technical data: - Fan power 2.2kW (ATEX) - Fan suction capacity: 12000 m³/h (max 1100Pa) Hfjdpfjia Taisx Abned - Lighting: 1pc 2x36W (ATEX) - Connection voltage: 400V - Frequency converter for smooth regulation of the fan - Three-stage air filtration - Intended for explosive environments - EX - Complete technical documentation - CE Documentation - Warranty Possibility to order machines in various individual configurations and dimensions! Do not hesitate to contact us.

Condition: excellent (used), Year of construction: 2007, functionality: fully functional, overall weight: 3,500 kg, year of last overhaul: 2019, Equipment: documentation/manual, Eladó egy teljesen felújított Cattinair Rotoclean G-8 típusú rotációs festőrobot: Hedpfxjtiy Dgj Abnofd A festőrobot, amint a képeken is látható, teljesen felújított állapotban van. Nyolc karos, 360 fokban forgó rendszerrel rendelkezik, minden karon legfeljebb két szórópisztolyt tartalmazó egységgel. A három körös zárt rendszer lehetővé teszi a hatékony festést. A festeni kívánt tárgyakat fotocellás érzékelőkkel ellátott motoros szállítószalag továbbítja kilenc rozsdamentes acél övből készült szállítószalag segítségével. A szállítószalag rendszere egy hígítóval töltött tisztító tálcán fut keresztül, így a tisztítás automatikus. A géphez kéményes elszívó rendszer is tartozik. A gép kifogástalanul működik, jelenleg is kipróbálható, és 12 festőpisztollyal van felszerelve. A felújítást követően csak kevés üzemórát futott.

Condition: good (used), Year of construction: 1985, total height: 2,000 mm, overall weight: 150 kg, total length: 1,300 mm, total width: 1,000 mm, inner dimension height: 950 mm, inner dimension width: 900 mm, inner dimension length: 1,100 mm, Paint spray booth for small parts / color samples, exhaust air volume 3100 m3/h, motor 0.75 KWDimensions 1000x1300x2000 mm, approx. 150 kg Hfodpfx Asvl H Sfsbnod

Condition: new, Year of construction: 2026, Internal dimensions LxWxH 4300x1700x2200mm, Temperature max. 220°C, Hfsdpfxsizw E Uo Abnod oil, gas or electrical heated possible, Tracks for hordes waggons possible, Manual or automatic transport usable, flap or sliding doors producable.

Condition: new, Year of construction: 2026, Some components can be choose: - chamber pretreatement with osmosis plant, Hjdpfx Abjizw Hnenofd - Water drier oven, - Powder curing oven, - manual transportsystem inkl. steel frame, - Controler siemens, Additionsal chooseable components possible.

Condition: new, Year of construction: 2026, Powder coating booths, sizes defined by customer, Hedpfxeizw Hys Abnjfd Additional equippment possible.

Condition: new, Year of construction: 2026, Wetpaint Spray-/ Dryingcabine Internal dim. L8000 x B4000 x H3000mm 30.000m³/h Inletair/ 30.000m³/h evaporation Internal Temp. 20°C man. adjustable, Drying Temp. up to 70°C Indirect Gasburner approx 300KW (-10°C - +20°C) Software in delivered switch box Hedpfxshzbq Te Abnsfd Inlet air ceiling with filter G4/EU4 und NF600PA, Outside air bollom using grids and PS50 glas fiber Light (4x18W) wall integrated LED, 750LUX Grid point weight max750kg

Condition: new, Year of construction: 2026, functionality: fully functional, workpiece weight (max.): 250 kg, Manual powder coating system, suitable for gas cylinder coating Hodpfxswhbvps Abnjfd

Condition: new, Year of construction: 2026, Desciption in english language after demand. Hsdpfx Asdulhvobnjfd

Condition: new, Year of construction: 2024, ### 🔫 ProfiGun PM-1 powder gun Lightweight, ergonomic, perfectly balanced with a contoured grip. ✋⚖️ Adjust powder output and switch programs directly on the gun. 🎛️ Ceramic cascade up to 100,000 V for efficient charging of all powder types. ⚡ New-generation nozzles improve penetration on complex parts. 🎯🧩 Profiled nut for a secure grip + conductive handle for excellent operator grounding. 🔩🧤 Impact-resistant materials, fully demountable design, replaceable powder path tube. 🛡️🛠️ Patented in the EU and US. Polarity: negative. 🇪🇺🇺🇸➖ One-piece powder path + quick-release hose coupling reduce leaks and speed up hose changes. 🔌✅ Hedpfxeflpi Ne Abnefd ### 💨 ProfiJector powder pump Efficient injector with an optimized feed angle validated by research. 📐🔬 Lower powder and air consumption vs. right-angle injectors, with low running costs. ♻️📉 European patent protected. 🏅 ### 🖥️ PSS controller - 7" touchscreen 7-inch glove-friendly touch panel. 🧤📲 3 auto programs: overcoating, hard-to-reach areas, flat surfaces. 🔁 Fine tuning: 0.1 kV and 0.1 uA resolution. 🎚️ Advanced pneumatic valves for precise air dosing (patent pending) + real airflow measurement to detect drops or blockages. 💨📈⚠️ Diagnostics, program naming, external control via Modbus. 🧠🔧🔌 ### ⚡ ProfiCharge ceramic cascade (made in Poland) High-precision ceramic cascade up to 100,000 V, manufactured in Poland. 🇵🇱⚡ High-frequency ion emission (up to 17,000/sec) improves charging - less powder to the collector, more on the part. 🎯📉 Ultra-precise current control: 0-100 uA, stable even below 10 uA (0-10 uA focus with 0.1 uA steps). 🎛️ ### 💨 Air and application quality features Electronically controlled needle valves + integrated flowmeters for real-time, precise air delivery. 💨✅ Adjustable electrification curve for different powders and demanding parts. ⚙️🧩 Non-stick, puncture-resistant nozzles resist electrical breakdown, reduce clogging, and simplify color changes. 🧼✨ Automatic gun purge (from handle or screen) for faster, cleaner color changes. 🔁💨 ### 🛡️ Safety and compliance Discharge energy below 2 mJ + antistatic hose with double grounding strap. ⚠️🔒 ATEX and EN 50050-2 compliant for potentially explosive areas. ✅ ### 🧠 Productivity and support Quick Program: fast switching via rapid trigger presses. ⚡🎛️ Visual wear counters + fault history, suggestions, and self-monitoring diagnostics. 👀🔧 Up to 8 languages: PL, EN, DE, FR, RU, ES, IT, SV. 🌍 Animated troubleshooter for guided diagnostics. 🧭 Professional mode (hints on/off) + daily and job statistics for order management. 📊⏱️✅

Condition: like new (used), Chamber filter press from Netzsch. 20 plates 40x40 cm. Condition: excellent. Hfsdpfsxn Azdex Abnjd

Year of construction: 2025, condition: new, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ Hfodpfsfz Nd Isx Abnod 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Year of construction: 2025, condition: new, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ Hedpfjfx Nfmex Abnofd 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Year of construction: 2025, condition: new, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Hodpfx Asfz U Nbebnsfd Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Year of construction: 2025, condition: new, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Hfedpfeflk Awox Abned Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Year of construction: 2025, condition: new, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Hfedjfzb Rcepfx Abnod Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡