Used paint finishing systems for sale (89)

Condition: used, Year of construction: 2003, functionality: fully functional, total height: 4,000 mm, total length: 7,100 mm, total width: 8,100 mm, temperature: 80 °C, heating capacity: 116 kW (157.72 HP), Equipment: cabin, Complete wet paint installation with prep area, wet paint booth, mixing room, drying oven, and finishing zone. The installation can still be inspected in Diest. More details in the attachment or upon request. - Dimensions: LxWxH = 8,100 x 7,100 x 4,000 mm (external) and 8,000 x 7,000 x 3,950 mm (internal). - Height to underside of rail = 3,740 mm measured from floor level. - With a shared sliding door with the spray booth. Redox H Rhrspfx Aczsw - Sliding doors as oven exit door: WxH = 1,200 x 3,800 mm, equipped with 1 window, 2 panels. - Emergency door with window in side wall: WxH = 800 x 1,900 mm, self-closing with door closer and latch. The emergency door is fitted with sealing rubbers, large in diameter and highly elastic EPDM quality. - Wall type: vertical double-walled sandwich panels filled with mineral wool, thickness 55 mm. Includes lighting, ventilation unit, control panel, and a complete monorail system in front of and throughout the installation up to the finishing zone.

Condition: good (used), Paint unit, paint pump GRACO MERKUR + Graco G40 gun. Redpfoulc S Rex Aczjw

Condition: used, Year of construction: 2008, Max. weight per suspension point 44 kg Conveying Technology (Frequency-Controlled) 0,6 - 2,0 m/min Total chain length ca. 40.500 mm indexing 270 mm In our assessment, the paint line is in good used condition. Rodpfozbvlwox Aczsw Accessories, as well as the tools and clamping devices shown in the images, are included in the scope of delivery only if explicitly noted in the additional information. Subject to changes, errors in technical data and specifications, and prior sale!

Condition: used, Year of construction: 2024, operating hours: 300 h, functionality: fully functional, 1. MERKUR Airless Pump 45:1 Rsdpfoyx Irlox Aczew Ratio: 45:1 Maximum fluid output pressure: 310 bar Maximum air inlet pressure: 6.2 bar Fluid flow at 60 cpm: 3 lpm Volume per cycle: 50 cc Air consumption at 7 bar and 20 cpm: 0.48 m³/min Fluid inlet: ¾” Fluid outlet: 3/8” Includes: wall mount, surge filter, suction hose, suction pipe, suction filter. 2. XTR 5 Airless Manual Spray Gun Maximum fluid pressure: 345 bar Fluid passage: 2.3 mm Fluid inlet: ¼” Weight: 411 g Dimensions: length 111 mm x height 180 mm Wetted parts: aluminium, stainless steel, polyethylene, polyurethane, polypropylene, nylon, acetal, carbide, solvent-resistant O-rings. 3. Mini Merkur Airless 30:1 Ratio: 30:1 Maximum operating pressure: 207 bar Maximum tip size: 0.019” Fluid flow at 240 cpm: 1.5 lpm Air inlet: 3/8” Fluid outlet: ¼” Minimum compressor capacity: 1.5 HP Includes: wall mount, suction hose, suction pipe, suction filter. Key advantages: convertible wall mounting, pneumatic motor, consistent finishes, low air and material/solvent consumption. 4. Silver Plus Airless Manual Spray Gun Maximum fluid pressure: 345 bar Fluid inlet: ¼” Weight: 510 g Wetted parts: stainless steel, polyethylene, polyurethane, nylon, Teflon. 5. Product Hoses with Stainless Steel Braid Braid: AISI 304 Inner tube: Teflon Applications: chemicals, solvents, steam. Length: 10 metres Diameter: ¼"

Condition: new, Year of construction: 2026, Variable, adjustable painting turntable • Numerous adjustment options for small and large, solid workpieces • Stable • Can be operated by one person; rotatable with fixed outriggers and adjustable swivel arms • Height-adjustable Technical data: Rjdpfx Aebzmagsczjw Length: max. 1850 mm Width: max. 800 mm Height: 1000 – 1300 mm Load capacity: 300 kg Top quality product Can be shipped by us via UPS. Assembly is required. Location: In stock at Bitburg warehouse.

Condition: new, Year of construction: 2026, Rehnen Spraying Table Lacky The advantages: Rjdpelrrrmsfx Aczsw Thanks to its arms, which can rotate 360°, it always provides the best support and a good surface for all workpieces. Easily adjustable in height and rotatable by 360° for quick and efficient work. Thanks to its covers, even after intensive use, the arms can still be moved. Height in mm: 950-1250 Width in mm: 600-1120 Length in mm: 700-1260 Diagonal in mm: 900-1680 Load capacity in kg: 100 Location: in stock – available immediately.

Condition: used, Year of construction: 2001, SUPERFICI UV lamps Rjdpfx Acozg Ht Uezjw Type: TU166/35-3UV55 Effective working width: 1300 mm 3 UV radiators with a power of 120 W/cm Tube conveyor with adjustable speed: 4-16 m/min External air filters Lamp dimensions: 250x360x160 cm Control cabinet dimensions: 80x200x210 cm

Condition: used, The painting line consists of the following elements: 1) MTL.120 monorail, 600 kg load capacity, equipped with hooks and rotation drive 2) Dry spray booth for painting 3) Dust extraction booth 4) Ducted solvent extraction system 5) Ducted paint oven system 6) Reciprocator for electrostatic spray guns Rsdpfxsyy Rivo Aczew 7) Wagner 30:1 high-pressure pump for solvent-based electrostatic installation 8) Protective enclosure for low-pressure ASAI system 9) Flow coating system 10) Low-pressure pump for ASAI electrostatic installation

Condition: used, Year of construction: 2009, functionality: fully functional, total height: 5,500 mm, total length: 16,500 mm, total width: 6,400 mm, Equipment: cabin, For sale is a high-quality, modular industrial coating system from the reputable manufacturer RIPPERT Anlagentechnik (consignment no. 20809025), manufactured in 2009. The system is located in Nuremberg, has a linear layout, and is fully documented. Ideal for industrial processing of large parts or series production. Dimensions: L x W x H: approx. 16.5 x 6.4 x 5.5 m Combination painting booths (1 & 2): each approx. 6 x 4 m Washing booth: approx. 4.5 x 4 m SYSTEM SCOPE: - 3x Combination painting/drying booths: Including large folding doors, complete lighting, and supply/exhaust air ducts. - 1x Industrial washing booth: For professional workpiece cleaning and preparation. - 1x Technical room & daily supplies storage: Contains the media control system (RLT 4.0) and an integrated logistics zone. TECHNICAL DATA & CONTROL CABINET: - Central control cabinet: Rittal TS 8005 floor-standing enclosure (dimensions: 3600 x 2200 x 500 mm, RAL 7035). - Connection values: Main circuit 400 V, rated current 450 A with integrated PLC control. - Media connections: Prepared for gas (burners 1–4), compressed air, demineralized/city water, wastewater, and pump warm water. IMPORTANT CONDITION NOTE & DELIVERY SCOPE: The original operating manual (volume 2a: mechanics/drawings) and the complete electrical documentation are included in the delivery scope. Note: Offered as shown in the pictures, with the exception of the pallets in the foreground. DISMANTLING AND DELIVERY CONDITIONS: - Self-dismantling (preferred): Professional dismantling and transport are carried out by the buyer at their own cost and risk. - Dismantling for an additional fee: Organized dismantling or provision is possible after prior agreement and cost coverage. KEY DATA & LEGAL INFORMATION: - Location: Nuremberg - Inspection: Possible after prior arrangement. Upon request, loading and transport (throughout Europe) can be organized for an additional fee. Upon request, transport and loading can be organized for an additional fee throughout Europe. Prices plus VAT. Inspection is possible by appointment. Contact us, our team will be happy to assist you further. Trade-in or exchange possible! Machine Buying / Selling PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES, ETC. Redpfsy U I Ulex Aczjw Do you need a high-quality, but affordable metalworking machine for your production? Or do you want to sell yours? For further information or contact options, please visit our website.

Condition: new, Year of construction: 2026, functionality: fully functional, warranty duration: 12 months, suction capacity: 3,900 m³/h, input voltage: 400 V, power: 1.5 kW (2.04 HP), Equipment: cabin, documentation/manual, emergency stop, lighting, dimensions without fan and control panel! Work area - dimensions (mm): 990(w)x800(d)x1100(h) Overall dimension(mm): 1100(w)x1900h)x1100(h) Technical data: - Fan power 1.5kW (ATEX) - Fan suction capacity: 4100 m³/h (max 750Pa) - Lighting: 1pc 2x18W (ATEX) - Connection voltage: 230V - Frequency converter for smooth regulation of the fan - Three-stage air filtration - Intended for explosive environments - EX - Complete technical documentation - CE Documentation - Warranty Redpfeia Tabox Aczsw Possibility to order machines in various individual configurations and dimensions! Do not hesitate to contact us.

Condition: good (used), Year of construction: 1989, functionality: fully functional, Equipment: cabin, Manufacturer: Garmat Belgium Type: M 6/7A Year of manufacture: 07/1989 Work area volume: 70.5 m³ Fan capacity: 24,000 m³/hour Motor power: 7.5 kW Gas burner: 200 kW Total electrical connection value: 14 kW Operating voltage: 380/220 V The 24,000 m³/hour and 200 kW gas burner make this a serious, professional booth, not a hobby version. Fully functional; Burner and fan are operating; Filter system is complete; No significant rust damage. Internal length: approximately 6.70 m Internal width: approximately 4.0 m Internal height: approximately 2.5 m. The dimensions are approximate. External dimensions: 6.85 x 600 x 310 (approx.) Redpfxszcfp Is Aczew The booth can be inspected, and it must be dismantled by the buyer. We will arrange for a forklift to load it.

Condition: used, Year of construction: 2008, functionality: fully functional, Technical specifications: Washing booth: Manufacturer: Hege Year of construction: 2017 Washing equipment: Steam cleaner, electrically heated Ventilation: Supply and exhaust air Heating: Gas burner Dimensions: (l x w x h) 8000 x 5000 x 3000 mm Preparation room Manufacturer: Walther Pilot Year of construction: 2008 Ventilation: Supply and exhaust air Heating: Gas burner Dimensions: (l x w x h) 5140 x 4120 x 3000 mm Painting booth Manufacturer: Walther Pilot Year of construction: 2008 Ventilation: Supply and exhaust air / Recirculation mode possible Heating: Gas burner Dimensions: (l x w x h) 6250 x 4120 x 3000 mm Drying 1 Manufacturer: Walther Pilot Year of construction: 2008 Ventilation: Recirculation mode Heating: Gas burner Dimensions: (l x w x h) 6250 x 4120 x 3000 mm Drying 2 Manufacturer: Hege Year of construction: 2017 Ventilation: Recirculation mode Heating: Pumped hot water Dimensions: (l x w x h) 5840 x 4120 x 3000 mm Lift and lower station Rodpezdc D Sefx Aczow Manufacturer: Hege Year of construction: 2017 Lifting capacity: 980 kg Manual push conveyor: Year of construction: 2008 / Extension 2017 Load capacity: 400 kg/m Operating mode: manual

Condition: new, Year of construction: 2026, functionality: fully functional, type of input current: three-phase, warranty duration: 12 months, Paint/spray wall dimensions without fan and control Panel! Extraction surface - dimensions (mm): 4430(w)x1900(h) Overall dimension(mm): 4530(w)x2350(h)x810(d) Technical data: - Fan power 4.4kW (ATEX) - Fan suction capacity: 24000 m³/h (max 1200Pa) - Connection voltage: 400V - Frequency converter for smooth regulation of the fan - Three-stage air filtration - Intended for explosive environments - EX - Complete technical documentation - CE Documentation - Warranty Rodpfxoia Ta Us Aczew Possibility to order machines in various individual configurations and dimensions! Do not hesitate to contact us

Condition: new, Year of construction: 2026, functionality: fully functional, type of input current: three-phase, warranty duration: 12 months, Equipment: cabin, Paint/spray booth dimensions without fan and control Panel! Extraction surface - dimensions (mm): 4430(w)x1900(h) Overall dimension(mm): 4530(w)x2350(h)x1910(d) Technical data: Rsdpjia Taxefx Aczsw - Fan power 4.4kW (ATEX) - Fan suction capacity: 24000 m³/h (max 1200Pa) - Lighting: 2 pcs 2x58W (ATEX) - Connection voltage: 400V - Frequency converter for smooth regulation of the fan - Three-stage air filtration - Intended for explosive environments - EX - Complete technical documentation - CE Documentation - Warranty Possibility to order machines in various individual configurations and dimensions! Do not hesitate to contact us

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, machine/vehicle number: 070079A, total height: 4,500 mm, total length: 5,400 mm, total width: 5,500 mm, Equipment: documentation/manual, Giardina high-bay dryer, manufactured in 2007 equipped with three different climate zones: evaporation zone – heating zone – drying zone Fitted with explosion-proof components, making it suitable for use with water-based and solvent-based paints Redezcnu Hopfx Aczjw Mobile pallets with conveyor belts, eliminating minimum size requirements for components Continuous vertical conveyor system

Condition: used, Year of construction: 2007, Professional combined painting and drying system with partition wall from Sehon, featuring a large cabin capacity and PLC control. Manufacturer: Sehon Innovative Painting Systems and Technology Model: SE-Professional Futura Year of manufacture: 2007 System type: Combined painting and drying system Cabin internal dimensions: 14,000 x 5,000 x 4,400 mm Cabin external height: approx. 4,900 mm Inlet/outlet gates: 2 units, front and rear Gate opening: 4,000 mm high x 4,500 mm wide Gate construction: insulated steel sandwich panel Gate panel thickness: 54 mm Housing: mineral wool-insulated steel cassettes Cassette thickness: 50 mm Housing color: RAL 9010 Pure White Material: chromated steel sheet Control: Siemens C7 PLC control Operation: Soft-touch panel with touch display Operating modes: Painting, drying, manual operation, timer operation Temperature control: stepless, microprocessor-controlled Filter monitoring: ceiling filter, pre-filter, paint separation mat Operating hour counter: integrated Alarm messages: visual and audible Pressure control: semi-automatic Supply air motor power: 7.5 kW Exhaust air motor power: 7.5 kW Motor power supply: 4 x 400 Volt Total connected load: approx. 37 kW Supply air unit: high-pressure radial fan Exhaust air unit: high-pressure radial fan Airflow rate control: adjustable motor slide Filter system: pocket filters on sliding rails Pre-filter efficiency class: EU3 Fresh air duct: galvanized steel sheet Exhaust air duct: galvanized steel sheet Fresh air duct height: approx. 6 m above floor level Exhaust air duct height: approx. 10 m above floor level Solvent pipe: available Hot air generator: indirect oil or gas firing Combustion chamber material: chromium steel V4A Combustion chamber material numbers: 1.4828 / 1.4541 Burner system: 4-pass system Oil burner: Elco-Klöckner Vectron L04.480 Duo Oil burner power range: 110 - 350 kW Gas burner: Elco-Klöckner EK04.34 G-ZVT1+QS Gas burner power range: 90 - 330 kW Gas burner design: Low-NOx with Quick-Start Type QS93 Solenoid valve: 1/2 inch Safety functions: safety and after-run thermostat Cabin construction: heat and sound insulated Condition: used Redsy Tiaaopfx Aczjw Further painting equipment available upon request. System currently still in operation, available from June 2026.

Condition: like new (used), Year of construction: 2016, operating hours: 100 h, functionality: fully functional, machine/vehicle number: 16P1269203, type of input current: three-phase, operating pressure: 7 bar, pump capacity: 7 l/min, power: 0.06 kW (0.08 HP), Equipment: documentation/manual, MODE OF OPERATION The system is suitable for the proportioning (metering) and mixing of two- or multi-component products. An electronic control system monitors and regulates the specified mixing ratio. The base paint flows continuously, and the control system mixes the necessary amount of hardener (in timed intervals) via a valve. The flow rate of the base paint and hardener is measured with flow meter cells. With plunger pumps, stroke sensors can also be used. The components and cleaning agents are supplied by feed pumps. Color Selection The mixing ratios, pot life, etc., are stored in recipes. The color can be changed by simply switching recipes. Further Features and Applications: For low to medium pressure (32.5 MPa; 325 bar; 4714 psi). 2K COMFORT XL for high pressure (53 MPa; 530 bar; 7687 psi). Modular design – can be configured according to customer requirements. Electronic accuracy in metering ensures consistent quality. Processing of water-based 2K materials is also possible, as all material-contacting parts are suitable for this purpose – for example, made of stainless steel. The fluid component of the Ex version is suitable for use in potentially explosive areas (Zone 1 and 2). Many displays of the functions are language-independent and use simple symbols. Text is displayed in the selected language. Consumption overview for each component and for cleaning agents, VOC documentation. Storage of the last 700 error messages with date and time. Safety through continuous monitoring of system parameters, informing the operator when even the smallest malfunctions occur and, if necessary, automatically interrupting production. Protection of parameters by security code. Settings can be saved on a USB stick. Electronic adjustment of the mixing ratio between 0.1:1 and 50:1. Redpfxszb I Spj Aczsw Up to 100 work recipes. (Also with robot communication or Profibus.) Possibility of two separate fluid circuits: – for simultaneous operation, – for quick color changes, – or to separate two incompatible 2K materials from each other (e.g., PUR and epoxy paints). Programmable cleaning recipes to save up to 60% of cleaning agents compared to conventional systems. Fully automatic control and monitoring for 1–4 guns. Compatibility with solvent-based and water-based products, as well as selective automatic cleaning with water and/or solvents. Use of manual or automatic atomizers. Release of automatic spray booth, automatic gun cleaning device, etc. Possibility of robot communication.

Condition: new, Year of construction: 2026, functionality: fully functional, type of input current: three-phase, warranty duration: 12 months, Equipment: cabin, lighting, Paint/spray booth Redpsia Taisfx Aczew dimensions without fan and control Panel! Extraction surface - dimensions (mm): 1600(w)x1900(h) Overall dimension(mm): 1700(w)x2350(h)x1910(d) Technical data: - Fan power 2.2kW (ATEX) - Fan suction capacity: 12000 m³/h (max 1100Pa) - Lighting: 1pc 2x36W (ATEX) - Connection voltage: 400V - Frequency converter for smooth regulation of the fan - Three-stage air filtration - Intended for explosive environments - EX - Complete technical documentation - CE Documentation - Warranty Possibility to order machines in various individual configurations and dimensions! Do not hesitate to contact us.

Condition: used, Year of construction: 2010, Powder coating line from 2010, in excellent condition. Currently in use, available for inspection and testing. Maximum part size: L x W x H = 2600 x 400 x 1850 mm Equipment Technological conveyor Automatic speed V = 1.2 m/min Speed regulation from 0.5 to 2.5 m/min Preparation station MNA-3-LPG, total length 16.7 m Entry area: L = 2.5 m a. Washing, degreasing and phosphating: L = 3.6 m Number of spray frames – 10 Number of nozzles in the frame – 18 Total number of nozzles – 180 Pump capacity – 162 m³/h Pump power – 15 kW 4 m³ capacity for active liquid Internal heat exchanger with LPG burner – 160 kW Temperature – 50°C Mechanical oil separator Filtration system Dosing system with diaphragm pump and regulator Washing time – 3 min b. Drip zone L = 3.1 m Drip time – 2 min 30 sec c. First rinse L = 1.2 m Number of spray frames – 4 Number of nozzles in the frame – 18 Total number of nozzles – 64 Pump capacity – 38 m³/h Pump power – 3 kW 1.5 m³ water capacity Rinse time – 1 min d. Drip zone L = 3.1 m Drip time – 2 min 30 sec e. Fine rinse L = 1.28 m Number of spray frames – 3 Number of nozzles in the frame – 18 Total number of nozzles – 54 Pump capacity – 33 m³/h 1.5 m³ water capacity Pump power – 3 kW Additional spray frame Rinse time – 1 min f. Drip zone L = 2 m Drip duration – 1 min 40 sec Three connections for the extraction system with three fans Working zone made of stainless steel Pipes made of PVC or stainless steel Redjv Ed Ukspfx Aczow 1 pc. Automatic dryer after washing AST-1-KLPG: Dimensions of the working zone L x W x H = 7000 x 3000 x 2800 mm Air curtains on each side to reduce heat loss Indirect heat exchanger, heated by LPG, 200 kW Three fans, air supply 6000 m³/h Two connections for the extraction system Temperature sensor and regulator Overheating sensor Circulation sensor Working zone made of galvanized steel Thermal insulation 200 mm thick Drying time – 10 min 1 pc. Automatic polymerization oven APT-2-KLPG Working area dimensions L x W x H = 10200 x 3600 x 2800 mm Air curtains on one side to reduce heat loss Two indirect heat exchangers heated by LPG, each 300 kW Eight circulation fans, each with a capacity of 6000 m³/h Two connections for the exhaust system Temperature sensor and regulator Overheating sensor Circulation sensor Working area made of galvanized steel Thermal insulation 200 mm thick Polymerization time – 25 min 1 pc. Overhead rail transportation system for ATR paint shop: Straight rail with hangers L = 400 mm – 146 m Drive station – 2 pcs. Tension station – 1 pc. Chain lubrication station – 1 pc. Rail support structure drawings – 1 set.

Condition: excellent (used), functionality: fully functional, BMB Coating System for Printed Circuit Boards, Model TUA-200 / 2 in EXCELLENT condition. Purchased: 2023 (as-new condition) and only in operation for 6 months. Version: Professional Version (excellent feature set) - High speed coating up to 4x faster - 3 coating processes in one unit - Suitable for components up to 1200x570 mm - Permanent viscosity/temperature control - Full traceability (depending on version) - Tool recognition and parameterization - Maximum protection by encapsulating components with coating - (Digital job-documentation system, currently under review) - Large paint tank capacity for tall components - Paint consumption calculation - Innovative, robust, and proven technology With the BMB Traceability and PDM System (equipment subject to clarification), you can track at any point which component was produced, when, where, by whom, and how. All requirements regarding ISO/TS 16949 are fulfilled. When setting up a tool, the PDM system automatically recognizes all necessary parameters for coating. Work instructions, videos, technical data sheets, processing notes, etc. – everything at your fingertips! 19″ swivel smart touch panel Viscosity control Tool monitoring: automatic recognition and adjustment Electrically height-adjustable machine Coating processes: - Dip Coating (DipCoat) - Selective Contact Coating (SCC®) Rsdpfev I Tb Eox Aczew - Selective Transfer Coating (STC®) The system can be shipped by freight carrier upon request. #8300

Condition: like new (used), functionality: fully functional, machine/vehicle number: MD1001, total height: 150 mm, total length: 45 mm, total width: 52 mm, overall weight: 50 kg, PROMIX 2KS MIXER, 1 COLOR + 1 CATALYST + 1 AIR + SOLVENT Rsdpfxewp Slko Aczjw SHIPPING AVAILABLE 🚚 -Brand: Graco -Reference: MD1001 -UPC Code: 633955370647 -General Industry: Paints and Glues -Application: Two-component paints, solvent and water, glues, varnishes, lacquers. -Mixing close to the guns for greater control -Compatible with solvent- and water-based epoxies and polyurethanes -Mixing ratio up to 30:1 -Pressure: 275.6 bar (4000 psi) -Pre-owned, fully inspected -Warranty: 1 year -OPTIONAL: COLOR AND CATALYST CHANGE WITH CONTROL (PRICE ON REQUEST)

Condition: ready for operation (used), Year of construction: 2000, functionality: fully functional, machine/vehicle number: 2000/80205, Complete powder coating line with automatic powder recovery. 1. WAGNER automatic spray booth – year of manufacture: 2000 Serial no.: 2000/80205 Booth dimensions: 5.3 x 2.2 x 2.8 m Currently equipped with ZEUS Tribo spray guns – 8 units with rotation Type of operation: pass-through Entry size for coated parts: 100 x 158 cm 2. IMEL washer – external dimensions: 3 x 12 x 4.2 m (L-shaped) - Washer entry size: 72 x 144 cm - Water tank: 3 x 2.2 x 1.2 m - Capacity: approx. 6,000 liters (located under the washer) - Heating by Sant Andrea burner, model KB 40 GM with modulating capacity from 179 to 468 kW (gas burner) 3. WAGNER powder filtration system, dimensions: 1.5 x 3.2 x 5.5 m 4. Overhead conveyor – length approx. 100 m, self-propelled 5. WAGNER powder recovery unit with cyclone 6. Oven (with 2 circuits) with gas burner 163 – 390 kW - One circuit for drying parts after washing - Second (longer) circuit for curing powder after application - Oven dimensions: 12 x 7 x 5.3 m; maximum coated part size: 60 x 120 cm Rjdpeyrr Rqefx Aczsw Additionally, we have 2 oil burners of similar capacity as alternatives to the gas burners. Approximate installation footprint: 30 x 11 m.

Condition: used, Year of construction: 2018, Wagner electrostatic powder coating system for enamel application, year 2018, serial number 30210, with a touch screen control panel, consisting of: • 1 PVC spray booth with overall dimensions of length x width x height: 3200 x 2130 x 4000 mm • Dimensions of the part entry/exit opening: 1000 x 1000 mm • 1 HERDING filter (cyclone) with automatic powder recovery • 1 shaker for powder suspension with extraction and powder recovery • 1 EP powder feeder with 32 pumps (injectors) • 12 automatic spray guns, model PEA-C2, for enamel application, with a double blade head • 9 universal EPG/S2 control units for powder guns • 1 GCA compressed air treatment unit used in the system (heating/humidification) • 1 overhead monorail transport system, 35 m long, serving the spray booth. The line is located at the parent company in Italy, near the town of Pordenone. Redpfx Asy Tn Ateczew Direct contact is possible, upon prior arrangement.

Year of construction: 2020, condition: new, High hauling power Soundproofed construction Electronic control 4 "touch panel Constant measurement of flow and filter clogging Final filters Inverter controlled fan • Electrical data 22kW 380-400V 50-60Hz • Theoretical capacity 12000 m3 / h • 1/4 "pneumatic connection • Number of filters 8 pcs. • 160 m2 filtration area Rsdpfefz I Rmex Aczjw • Automatic filter cleaning • Air consumption max. 12L 6-8 bar / shot • 50L waste container capacity Description • Dust collector equipped with an efficient radial impeller • Two working modes - Full power and ECO • The basis weight of the material used in the filter is as much as 260g / m2 • High suction power with low energy consumption • Waste container for easy removal of paint deposits • Inspection door for filter replacement • Each filter has its own solenoid valve Power Inverter Constant air flow measurement Vacuum sensor Capacity (m3h) Filter area (m2) Paint container

Year of construction: 2020, condition: new, Description Automatic sprinkling chamber is a solution that allows you to reduce costs, improve quality and increase the efficiency of the surface preparation process. The automatic sprinkling chamber is equipped with a set of spray pumps, it was designed so that as little liquid as possible after the process migrates to subsequent processes, thus saving money and improving the quality of washing. This is very important, because apparent savings in systems made without the use of these solutions can generate in the future much higher costs associated with chemistry and waste disposal which will simply be more. Attention should also be paid to problems with maintaining the required bath parameters. Research and development work allowed us to develop a sprinkling chamber with the function of drying details (option) with hot air blown by a set of fans after the washing process. The sprinkling chamber is equipped with an advanced system for creating your own macro programs, which can consist of 10 steps each, depending on the number of tanks, processes can be repeated, their order can be changed, etc. Each tank has its own unique icon and name, enabling the operator to work intuitively. Rodpfofy T Szex Aczsw Optionally, the tanks can be equipped with bath replenishment systems, which can be performed e.g. between processes or at the end of the cycle. • Control installed on the swivel arm for better access • PLC microprocessor control • 7 "touch operator panel • Very large number of nozzles, compared to other solutions • (Option) The possibility of drying details after the washing process • The ability to create your own advanced programs • Advanced damper system made of acid-resistant sheet metal, double protected by limit switches • Tight closing and full flap opening control system • To minimize fluid mixing, separate pipelines, nozzles, tanks for each treatment • Intelligent control - in the event of a power cut / sudden shutdown, no mixing of liquids possible • Fully automatic operation/ Prices are given in the catalog