Glazing Press

RYKO GmbH VK-3522

Condition: excellent (used), Year of construction: 2014, operating hours: 5,059 h, Functionality: fully functional, pressing force: 48 t, bale weight: 550 kg, filling opening width: 1,020 mm, filling opening length: 1,250 mm, total height: 2,800 mm, bale height: 750 mm, bale width: 1,100 mm, overall weight: 12,000 kg, transport height: 2,800 mm, oil tank capacity: 300 l, power: 30 kW (40.79 HP), net weight: 12,000 kg, volume flow: 332 m³/h, nominal current: 59 A, Technical information baler: Manufacturer HSM GmbH + Co. KG Typ VK 4812 Year of construction 2014 Hours of operation 5,059 hours, stand November 2024 Press power main press 48 tons Specific press capacity 58,2 N/cm² Feed channel 1,250 x 1,020 mm Theoretic cycle time 11.2 sec. Theoretic throughput rate 332 m³/hour Bale size 1,100 x 750 x 600 up to 1,200 mm Driving motor 30 kW Connected load 32 kW Rated current 59 A Tying system 4-fold horizontal, fully automatic Throughput rate at a bulk weight of 20 kg/cbm up to 6 tons/hour bulk weight of 50 kg/cbm up to 13 tons/hour Bale weight up to 550 kg, depends on material SPS controller Siemens SIMATIC S7-200 Operating panel Siemens HMI Touch Panel Filling quantity hydraulic oil tank 300 L Oil type HVI 46 Machine installation dimensions with bale chute 10,046 x 4,387 x 2,705 mm (l x w x h) Transport dimensions baler 8,500 x 2,500 x 2,750 mm (l x w x h) Machine weight press approx. 12 t Scope of delivery: Baler HSM VK 4812, without hydraulic oil, without conveyor system. Two wire reel boxes for 8 pieces 40 kg wire reels, without wire Bale chute Nksljvtpq Hjhcdwusw Machine documentation in German Comments: The press is equipped with an oil cooler and potential-free contacts for external control. The control cabinet is operated from the left in the direction of pressing, the needle unit is located on the right-hand side and can be folded back for transport. The press is in good condition, is currently still in operation and is used in a distribution warehouse for film compaction. In the 14th calendar week, the baler will be dismantled and replaced with a new, larger machine and will then be available for loading. A truck with an effective internal height of 2,800 mm is required to transport the baler. The press is loaded without hydraulic oil. The conveyor technology shown in the photos is not for sale and is not included in the scope of delivery. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagrams) is available in German. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: good (used), Year of construction: 2007, operating hours: 8,800 h, Functionality: fully functional, pressing force: 24 t, bale weight: 200 kg, filling opening width: 620 mm, filling opening length: 1,000 mm, bale length: 1,200 mm, total width: 2,825 mm, total height: 1,940 mm, total length: 6,250 mm, bale height: 500 mm, bale width: 700 mm, input voltage: 400 V, power: 9.2 kW (12.51 HP), operating pressure: 220 bar, Presskraft: 240 kN Spezifische Presskraft: 64 N/cm² Antriebsleistung: 9,2 kW Spannung / Frequenz: 400 V / 50 Hz Taktzeit im Leerlauf: 17,2 s Pressleistung Leerlauf (theor.): 73 m³/h Nkolhcdwjvq Rpleusw Breite der Einfüllöffnung x Länge der Einfüllöffnung: 620 x 1000 mm Ballenbreite x Ballenhöhe x Ballenlänge: 700 x 500 x 600-1200 mm Länge x Breite x Höhe: 6250 x 2825 x 1940 mm Gewicht: 4 t Art des Verbrauchsmaterials: Draht Pressgut: Folie, Gemischtes Papier, Kartonage, Stanzreste, PET Getränke und Aluminiumdosen,Weichverpackung

Condition: excellent (used), Year of construction: 2015, operating hours: 9,231 h, Functionality: fully functional, pressing force: 120 t, bale weight: 1,100 kg, filling opening width: 970 mm, filling opening length: 1,800 mm, bale height: 1,100 mm, bale width: 1,100 mm, overall weight: 42,000 kg, oil tank capacity: 2,000 l, power: 75 kW (101.97 HP), volume flow: 506 m³/h, nominal current: 140 A, Technical data baler: Manufacturer HSM GmbH + Co. KG, Germany Type VK 12018 R-FU Year of construction 2015 Operating hours 9,231 hours, as of July 24 Main press force 120 kN Specific pressing force 99 N/cm² Pressing force cutting edges free rammer 121 kN Dimensions of feed chute 970 x 1,800 mm Filling volume 1.92 m³ Theoretical cycle time in idle mode 15.5 seconds Theoretical throughput capacity 506 m³/hour Throughput capacity under operating conditions with a bulk density of 30 kg/m³ approx. 278 m³ or 8.3 tonnes/hour Bale dimensions 1,100 x 1,100 mm, the length is variable Drive power 2 x 30 kW with frequency converter. This corresponds to the output of two normal 45 kW standard motors, but saves up to 40 % energy via frequency control. Connected load 75 kW Total current consumption 140 A Fuse protection 200 A slow-blow 5-fold horizontal tying, fully automatic Throughput rates with a bulk density of 30 kg/cbm 8.3 tonnes/hour Bulk weight of 50 kg/cbm 25.3 tonnes/hour Bale weights with a bale length of approx. 1.2 m 800 up to 1100 kg/bale or 665 kg/m³, the figures refer to PPK Hydraulic oil tank capacity 2000 litres PLC control Siemens S7-300 Siemens TP 700 control panel Press dimensions assembled with hopper 12,557 x 4,450 x 6,232 mm (l x w x h) Press dimensions with conveyor belt 21,395 x 22,075 x 6,232 mm (l x w x h) Transport weight baler approx 42 t Special machine equipment: Filling opening length can be flexibly adjusted according to material requirements thanks to integrated distance measuring system on the main hydraulic cylinder Access locking by means of key transfer system Electro-hydraulic locking of the press carriage during the tying process so that the press plunger does not change position with highly expansive materials Wear areas in the press box made of double-walled sheet steel (the second layer is replaceable) Additional optional equipment ordered: Frequency-controlled main drive, 2 x 30 kW, with up to 40 % energy savings compared to the standard motorisation 2 x 45 kW, with the same power output Frequency-controlled oil cooler with a cooling capacity of 35 kW, incl. oil filter unit, for continuous operation with high utilisation and high ambient temperatures Switch cabinet heater Tank heating for the hydraulic oil Manual switch-off or switch-on of the number of strapping wires to save on strapping wire for non-expansive material Cutting-edge frei rammer with 121 kN pressing force Sensory wire monitoring, with press switch-off in the event of wire breakage or wire end Bale chute Large digit display for the remaining bale length Visual warning signal, mounted on the control cabinet Remote maintenance system for external data analysis and processing Control cabinet Cooling fan for cooling the frequency converters Condition of the baler: Njlevtqc Rshcdwuokw The entire baling system (baler and conveyor belt) is in good, operational condition and is cleaned, lubricated and maintained by the operator on a weekly basis in accordance with the manufacturer's specifications. The baler with conveyor belt is to be replaced with a new machine with a higher throughput capacity at the 19th calendar week. Scope of delivery: The complete baler line is for sale, with the associated chain belt conveyor, wire pulling stations (without wire), personnel protection system and bale chute.

Condition: as good as new (ex-display), Year of construction: 2024, Pneumatic Glazing Bead Saw Type GLSP-200N-AV Pneumatic Automatic saw feeding Pneumatic work piece clamping Adjustable table height 2 x 45° motors Accessories: HM Saw blade 200 x 2.2 x 32mm HSS Saw blade 103 x 2.0 x 32mm Z=60/45° Right Nslhcjuydgsdwuokw HSS Saw blades 103 x 2.0 x 32mm Z=60/45° Left Glazing Bead Simulation- System With feed cylinder, 1 Revolver stop with 16 stops and 4 clamping cylinders Fixtures for 2 Glazing Beads, support And leg adjustable for simulation Exhaust support D=80mm

Condition: as good as new (ex-display), Year of construction: 2024, Hydro Pneumatic Corner Crimper EVP-350HP Hydro-pneumatic press operation Press Strength 2 x 3.500 KP at 8 Bar Press Depth 30 mm Back centring positioner with Noljuxx Ushcdwujkw Pneumatic work piece clamping 3 sets standard crimping knives 3/5/7 mm Air service unit Profile support arms with Perdinax

Year of construction: 2021, Condition: new, Automatic Screw Unit SE1 SA Nkolhcdjuxyuowujw With automatic screw feeding Head only bench mount,...

Year of construction: 2018, Condition: as good as new (ex-display), Glazing Bead Saw GLSM-200E Manual saw feeding Pneumatic work piece clamping (4) Adjustable table height Nkjlhouxxxocdwusw Adjustable table height 2 x 45° motors Accessories: HM Saw blade 200 x 2.2 x 30mm HM Saw blades 103 x 2.0 x 30mm Z=60/45° Left HM Saw blades 103 x 2.1 x 30mm Z=60/45° right Variable measuring stick 1.5m Variable measuring stick 3.0m Support for measuring stops 3.0m

Year of construction: 2021, Condition: as good as new (ex-display), Automatic Double Screw Unit SE5 S With automatic screw feeding Head only bench mount Automatic working operations Depth stop control,... Neleuxyyohcdwuskw

Condition: new, Year of construction: 2025, Ballshaping- and Delaminationmill Molinator for fine delamination! Diverse Types: RW VKR16/3 / 22-37kW and RW VKR 22/3 / 75-110kW Input Composite Material Examples: Regrind from hair-wire, printed circuit boards, electronic circuits, other composited material. Al / Plastic, Cu / Plastic, Cu / Glass fibre, ABS / Plastic fibres, etc. Type selection: depending on the material / depending on layer thickness / depending on test‘s / according to the desired throughput. Description Molinator: In the inner acts very high forces Njlhcdwsdwqiuouekw (High acceleration / high relative-speed)! Bigger parts will be delaminated. Composite-material separates at the phase of boundaries. Metals will be ballshaped. Plastics depending on the specifications stays “fluffy” or will be grinded. These effects besides the desired delamination, are helpfully for the separation and are exactly coordinated to our separation-technology like Fluid Bed Separators / Sievemachines / Sifters.

Year of construction: 2011, operating hours: 15,840 h, Condition: ready for operation (used), Functionality: fully functional, machine/vehicle number: VKW-500 2212; VPS-N 2211, Production machine with two modules: for automatic winding of aluminum foil rolls, fresh storage foil, baking paper; and an automatic packaging unit that places the rolls in cartons. There are conveyor belts between the modules, it is equipped with a product labeling printer. Production materials need to be loaded. Nslhcdwjuxpq Ieuekw

Year of construction: 2025, Condition: new, Functionality: fully functional, The universal laser marking system LAS 28 from Systemtechnik Hölzer GmbH can be used for a very wide range of marking applications. With the integrated fiber laser you can mark almost all materials such as steel, carbide, aluminum and plastics. Depending on the requirements, the system can be equipped with a 20, 30 or 50 watt fiber laser. For permanent marking, the use of the laser is necessary in many industries. With the powerful laser software, texts, numbers, 2D codes, QR codes and logos can be realized with just a few clicks without extensive programming knowledge. Serial and article numbers are automatically incremented by the software after prior setting. In addition, the software can read data (variable information such as drawing numbers, project designations, etc.) from existing tables and automatically transfer them to predefined areas. The use of a hand scanner is also possible. The standard equipment includes a laptop incl. holder with Windows operating system. Optionally, the laser model LAS 28 can be equipped with a rotary axis (3-jaw chuck) for marking cylindrical parts. Further options, such as lateral extensions for marking long parts, can be realized. Nkjlhcov Sybysdwuow Made in Germany - Fiber laser 20W (Optional: 30W, 50W) - Wavelength 1064nm - marking field size 150x150mm (optional: 200x200) - optional: rotary axis (3-jaw chuck) - optional: digital height measuring system - optional: exhaust system (incl. activated carbon filter) - optional: Autofocus system - signal light for indication of operating status - marking software EZCAD (optional additional laser software) - Pilot laser (simple preview, contour preview) - focus finder (simple focus adjustment) - max. part height approx. 270mm - electrically adjustable Z-axis (adjustment of working plane) - frame made of aluminum profile - connection 230V - air cooled - Laptop with Windows operating system - dimensions: 800x 600 x 1660mm (LxWxH) - weight: approx. 80 Kg

Condition: like new (used), Year of construction: 2011, operating hours: 1,525 h, Functionality: fully functional, machine/vehicle number: W09SSA220BLSF8002, pto shaft: keine, fuel: diesel, cubic capacity: 6,600 cm³, type of cooling: water, cylinder stroke: 127 mm, Equipment: crane, For sale is a well-used SSA 700 log splitter. It is fully operational and in mint condition. The machine is being sold because our business is being remodeled and reorganized. It will be available starting March/April 2025. The machine includes a Bindenberger windshield washer. Nkeljvy Uudshcdwuew Price upon request.

Condition: as good as new (ex-display), Year of construction: 2024, Functionality: fully functional, machine/vehicle number: WKZ45-1030, Stock machine, can be inspected under power! We invite you to visit our technical center to see the quality and functionality for yourself. Material shredder 45KW Hopper opening: 1,030 x 1,235mm Rotor diameter 360mm Star-delta start-up, automatic shutdown at idle - Hydraulic slide equipped with pressure plates - Siemens PLC control Nslhcev Tdq Iedwuokw - Optionally with control cabinet extension for discharge conveyor belt + overband magnetic separator Complete solution with discharge conveyor belt in any design. Our core competence lies in providing our customers with exactly what they need. We work closely with our customers to develop customized, individual solutions and supply corresponding systems from our own production facilities. Please feel free to contact us by phone to find a suitable solution for your application. Conveyor belts, conveyor systems, discharge belts, belt conveyors, magnetic separators, overband magnetic separators, recycling, wood chips, plastic, metal-free metal detection, neodymium, overband magnets, magnetic belt separators, lifting magnets, filter rods, magnetic grids, magnetic grates, metal separators, block magnets, filter systems All prices are net prices plus 19% VAT. All information is subject to change without notice, only while stocks last!

Condition: used, Year of construction: 1994, Technical details: welding current - continuous: 40...400 A Length: 900 mm height: 1200 mm total power requirement: 13,8 kVA weight of the machine approx.: ca. 180 kg space requirements of the machine approx.: B:0,6xL:0,9xH:1,2 m MIG MAG Welding device -welding transformator as spare part donor - capacity 40A/15V up to 400A/34V - open circuit voltage -58V - characteristic constant - protection type IP23 - isolation type F Njlhcdweu Nwx Ueuekw - water cooled Circuit board A5 missing! *

Condition: used, Year of construction: 1998, Functionality: fully functional, machine/vehicle number: 004, For special lumber, when no moisture reduction is desired during steaming, the kiln can be insulated. MC control with lumberweight and electronically. SIGMA 9 QUATTRO with automatic stacking Lumber content 72 m³ (30 mbf) comparable to 210 m³ (90 mbf) vacuum dryers with fans or to 800 m³ (340 mbf) conventional dryers but more economical, without contamination of the atmosphere and with Super drying quality! Stacking equipment for plates 2025 Nkelsv S U Tqshcdwuow

Year of construction: 2023, Condition: new, Functionality: fully functional, Cost-effective single-column, microprocessor-controlled tensile testing machine for tensile, compression and bending tests up to 3kN Comfortable Windows software for universal test procedures, simple tests can also be performed without a PC. Made in Germany Basic equipment: • Machine with sensor (optionally between 50N and 3kN) • Accuracy class 0.5 • Windows based software Nkslhcsd H S Hisdwuew • Warranty 2 years Optionally available: • Extensive gripping tools (mechanical, pneumatic and hydraulic), for example: pressure platens Screw and wedge grips bending grips Special designs according to customer specifications • extensometer • Temperature and climatic chamber • Windows software PM-Soft-Smart for universal use, freely programmable • putting into operation and training

Year of construction: 2025, Condition: new, Functionality: fully functional, Semi-automatic depaneling / basic machine with parallel shuttle The dynamic depaneling machine LOW 4322 XL is especially suited for medium to high product volumes and meets growing demands in the production process. Printed circuit board blanks of various materials are separated using low-dust and low-stress sawing and milling techniques with maximum product flexibility, precision and throughput. Highly dynamic linear motor axes, tools and grippers meet the highest quality requirements and guarantee the depaneling machine a long service life and high reliability. Semiautomatic depaneling - solutions on demand The LOW 4322 XL depanelling machine enables fast product changeover while maintaining short depanelling and handling times. The blank printed circuit board is inserted with a parallel shuttle, picked up and fixed with pin clamping technology and, if necessary, in combination with vacuum suction cups. Nkolhovuw R Rocdwujw Made in Germany The machine is equipped with: - a shank and slice tool separation module on Z-axis (automatically rotatable 0-90) - X-Y cross table module in linear motor technology with high-resolution measuring system - 2-compartment loading module built as parallel shuttle, separated left and right with sliding doors - Steel welding frame with two maintenance doors - left and right. ESD - standard vision system base module for teach-in programming - Working area is 520 x 480mm - Automatic cutter length processing - Remote maintenance/support via remote connection - Touch IPC with Windows 10 Pro operating system - Laser axis measurement incl. protocol - Air ionization - Cutter breakage control for end mills only - Preparation for vacuum clamping technology - ESD powder coating, RAL 9002, disc and sliding doors Optionally a vacuum cleaner unit can be offered later.

Condition: new, Year of construction: 2025, Functionality: fully functional, total width: 2,650 mm, total length: 4,640 mm, total height: 2,200 mm, type of input current: three-phase, workpiece weight (max.): 80 kg, overall weight: 1,200 kg, input voltage: 400 V, space requirement height: 2,200 mm, space requirement length: 4,640 mm, space requirement width: 2,650 mm, grinding width: 950 mm, grinding belt speed: 25 mm/s, grinding belt length: 9,000 mm, extraction connection diameter: 180 mm, power: 5.5 kW (7.48 HP), grinding belt width: 150 mm, height adjustment type: electric, grinding length: 2,500 mm, motor speed: 1,435 rpm, input frequency: 50 Hz, table height adjustment: 500 mm, Equipment: documentation/manual, Long-belt sander M2S92-150 with two sanding belts for manual sanding, matting, and polishing. For processing steel, stainless steel, and brass. Not for aluminum or titanium! Scope of delivery includes: - Machine stand with connecting elements - Belt drive - Pneumatic belt tensioning and manual belt guide - Sanding unit with contact roller, manually movable from belt 1 to belt 2 - Electric table lift - Flat machine table - Workpiece stop on the machine table - Original equipment sanding belts - CE-certified version - Operating instructions + manufacturer's declaration according to Appendix 2 The sturdy machine with its welded steel construction runs very smoothly. The two machine stands are equipped with a crank so that even longer parts can be sanded on the machine. The sanding belt is guided by three belt guide rollers, providing the largest possible working area for the operator and thus ensuring optimal work, especially with hand sanding blocks. The belt is driven by a three-phase motor with a balanced belt drive roller. Each belt has a separately adjustable, pneumatic belt tensioner. This allows for optimal belt tension adjustment for each belt. The dust collection system is designed to effectively capture the resulting sanding dust and direct it to the extraction nozzle when connected to an appropriate extraction system. To ensure effortless operation, the sanding unit is mounted on play-free roller guides. The machine table can be easily and quickly adjusted to the required workpiece height using the electric table lift. The table lift guide elements are maintenance-free. For loading, the table can be extended far enough that workpieces do not have to be pushed under the sanding belt when placed on the table. The electrical controls for the main functions are conveniently located in the center of the machine. Machine color: RAL 9001 cream white and RAL 5003 sapphire blue Control cabinets and small housing in "light gray" The machine is supplied in its basic configuration with two initial equipment belts (W x L) 150 x 9000 mm and a contact roller approximately 50° shore for a belt width of 150 mm. Additional accessories: 3-axis table with integrated handling device for rotating and swiveling the workpieces. Nkjlhcov S Sr Rsdwuew The handling device is mounted in the center of the table under the insert frame. To work with the handling device, the insert frame is removed from the machine table. The handling device is equipped with four vacuum suction cups for holding the workpieces and consists of: The bearing with the rotary axis, to which a brake disc is mounted on the rear. The swivel device is attached to the front of the rotary axis. This can be locked at 0°, 22.5°, 45°, 67.5°, and 90°. An additional locking disc is mounted on the swivel head, allowing for fine adjustment of the workpieces to the sanding belt. The rotary and swivel axes are unlocked pneumatically via a foot switch, while the rotary axes are moved manually. Workpiece weight when used as a flat table with an inserted frame = 80 daN. Workpiece weight when using the handling device relative to the clamping plate = 25 daN or 120 Nm relative to the center of the rotary axis.

Condition: used, 5tSWF Krantechnik GmbH Nslhcdwodc A R Touskw

Condition: new, Year of construction: 2024, operating hours: 10 h, Functionality: fully functional, overall weight: 14 kg, total width: 245 mm, total length: 420 mm, total height: 450 mm, input voltage: 230 V, volume flow: 420 m³/h, air demand: 420 m³/h, Equipment: chassis, Fume extraction with remote control and suction hose Air inlet interface ρm flange Max. Power 300W Air velocity 24/ms Filtration efficiency 0.3 µm / 99.97%. Noise 59ᐸdb Length of suction hose 1.5M System shear flow approx. 420m³/h Dimensions L420 x B245 x H450 Weight 14.0kg Application: This product is suitable for places dealing with air pollution such as smoke, peculiar odors, dust, toxic and harmful gases generated during soldering process, laser marking and engraving, printing, etc. Nkslhcdounh Nmswuow - Extraction unit for use in the workplace - Separately replaceable fine dust pre-filter M5 - Large HEPA H 13 filter surface with 2.4m² for optimum particle filtration and long filter service life - Activated carbon for effective gas cleaning - Portable extraction unit, for flexible placement directly under or next to the workplace - Easy filter change - Variable power control through percentage speed settings in 10 steps - Health protection through electronic filter monitoring and filter alarm - Long service life thanks to high-quality EC blower - Quick, easy and stable installation thanks to Easy-Click system

Condition: used, Year of construction: 1999, Technical details: x-travel: 690 mm y-travel: 400 mm z-travel: 550 mm B-axis (table): 360° mm control: Siemens 840 D number of spindle speeds: max. 15 000 U/min tool clamping: System nach DIN 69893 tool taper: HSK-A63 tool changer magazine: chain magazine: 12 places Stück traversing speed: x/y/z Axis: 40 total power requirement: 195 kW weight of the machine ca.: 13,0 t Traveling Column Milling Machine - the tool changing unit consist of 3 -NC axis and 1 NC- rotary table axis - ATC ( with magazine) Nelhcou Idl Sodwuokw - rotary table Type SKH-NC 4/029, diameter=460mm , table surface plate Ø 500 x20mm, revolution per minute max. 22 rpm - control panel SIEMENS - Spindel-Typ: DRF-WE-255-N-W-15-30, 15000 U/min., Spindelleistung = 30 kW - chip conveyor Make Knoll type 400K-3/280, ejection height 1150mm - cooling system for spindle make SCHIMBKE Type DK 80V, 3,36 kW i.D. *

Year of construction: 1998, Condition: used, Technical details: profile width: 50 mm work height max.: 950 mm interface: RS 232 Pinout Window profile processing machine for materials such as plastic, aluminum and wooden windows in a continuous process. The materials are conveyed by a pneumatic transport and clamping system. The system consists of two work stations (machines), an electrical control cabinet, and a control panel and transport units. Nelsu Ibuwehcdwuekw As well as columns with transport system vibrator, chip transport unit and column with receipt printer. Our photos are first taken from the location and then further pictures are how the plant is stored in our stock ready for transport. Workstation no. 1 (machine 1): -sawing station with saw blade Ø 400 x 4,5mm -drilling unit with clamping cartridge (vertical upwards) -drilling unit with clamping cartridge (hotizontal) -Boring with clamping cartridge (vertical down) -twin drilling unit with clamping cartridge (vertical down) -45° drilling unit with clamping cartridge (upwards) Working station no. 2 (machine 2): -drilling unit with clamping cartridge (vertical upwards) -milling spindle horizontal with 11 side milling cutters -Drilling unit with clamping cartridge (vertical down) -Drilling unit with clamping cartridge (vertical upwards) -Drilling unit with clamping cartridge horizontal 2 transport units: motor driven -LxWxH: 5.650 x 2.400 x 1.000mm -track width 1.980mm 2 pieces transport units: motor driven -LxWxH: 2.150 x 2.750 x 1.050mm -track width 2.300mm *

Condition: used, Technical details: x-travel: ca.1000 mm y-travel: 400 mm z-travel: 420 mm control: Siemens Sinumerik 805/810 thread cutting up to max.: M 22 bore capacity in St 60 - full boring: 25 mm milling area: Leistung in St 60:150 mm sawing stroke: ca. 55mm mm range of revolutions per minute - continous: 20-6000 U/min Number of working hours: manual 26180 h tool turret: 12 Plätze/places tool taper: SK 40 total power requirement: 18 kVA Nolhcdeu Idnmjwuokw weight of the machine ca.: 5,0 t machine dimensions LxWxH: 2,9x2,5x2,8 m transport measurements machine: 2,4x2,6x2,75 m Equipment: - special equipment/device ( modulating clamping system) for milling jobs of profile materials with an automatic longtitudinal cutting to length device for workpieces via circular saw module. (without functionality) - hotrizontal tool clamping ( force fitted) with vise clamping system and parallel ledges.(momentarily approx. 80mm) - tool changer type Chiron - basket tool changer - tool clamping mechanically locked, infeed force 5000N - swarf conveyor make Knoll - loading and unloading system FMB LM RP 3000 The machine is not fuctional. On sale as is for a small budget i.D. *

Year of construction: 2003, Condition: used, Technical details: operating pressure: 10 bar voltage: 400/50 V/Hz Nolhcsu N Afgsdwuskw control voltage: 24 V total power requirement: 0,76 kw weight of the machine approx.: 160 kg dimensions L x W x H: 0,58x0,68x1,35 m heat exchanger application area: transportation of heat energy from a medium to another medium (liquid or gas) connections 3/4" for flow/return 2x both sides 2 Pieces available *

Condition: used, Year of construction: 2010, Technical details: x-travel: 800 mm y-travel: 685 mm z-travel: 630 mm c-axis: 360° (Planscheibe-Tisch) control: Siemens 840D Power Line spindle speed:: 20 - 10.500 U/min max. torque on the spindle: 180 Nm tool taper: HSK -A63 DIN 69893 tool changer with: 40 places no. of tables: 2 table swivelabel +/-: je 120 (a-Achse) ° table surface area: 280 x 275 mm table load capacity: 320 kg interface: RS232 Number of working hours: ca. 40.000 h Total power requirement: 37 kW Nslhou Idgpocdwuekw dimension machine xH: 4,0 x 4,4 x 3,0 m dimensions LxWxH: Späneförderer: 2,1 x 1,05 x 1,5 m dimensions L x W x H: Kühlschmieranlage: 1,3 x 1.6 x 1,95 m 5 - axis machining center CNC machining center Clamping table for 4th and 5th axis (swivel 120° right/left/speed 50 rpm and turn with faceplate Ø 280mm/200 rpm) max. workpiece size 940 x 650mm for/on table with chip conveyor make Knoll, 750 K-1/150; year of manufacture 2009 Bürener coolant system with paper belt filter belt width 700mm; year of manufacture 2009 for both control cabinets with cooler Rittal Accessories i.D. *