Section Shear - Combined

PEDDINGHAUS Peddy

Condition: good (used), functionality: fully functional, Year of construction: 1978, Equipment: foot remote control, Performance data: Sectional steel shears: L-steel 90° cut 80 x 8 mm L-steel 45° cut 50 x 6 mm Section steel cutter: L-steel 90° cut 60 x 6 mm T-steel 90° cut 60 x 7 mm L + T steel 45° cut 50 x 6 mm Special knives: U-steel 80 mm I-steel 100 mm Flat steel 80 x 12/ 120 x 8 mm Round steel cutter: Round steel 28 mm Square steel 25 x 25 mm Flat steel shear 100 x 11/10 mm triangular notcher 8 mm strokes: 36 1/min drive: 2,2 kW Pedpfxehx Ekps Af Serf weight: approx. 450Kg Incl. base frame as shown All data without guarantee. Subject to prior sale. The object of purchase is sold under exclusion of any warranty. The exclusion does not apply to claims for damages arising from grossly negligent or intentional breach of obligations of the seller and for any injury to life, limb and health.

Condition: good (used), Cutting performance: Flat steel shears Blade length: 250 mm Sheets up to: 13 mm Flat steel up to: 150 x 16 / 200 x 13 mm Profile steel shears Angle iron up to: 110 x 10 mm Miter: 45° up to 90 x 9 mm T-iron up to: 110 x 10 mm Miter: 45° up to 90 x 9 mm U and I steel up to: NP 18 Stroke rate: approx. 30 1/min. Bar steel shears Round steel up to: 42 mm Square steel up to: 38 mm Notcher Sheets up to: 12 mm Notching width up to: 50 mm Notching depth up to: 85 mm Hole punch Thrust: 370 mm Punching capacity: approx. 50 t = 25 Ø x 16 mm / 20 Ø x 19 mm Drive power: 3.0 kW Weight: approx. 2,200 kg Equipment - Hand and foot release - Support table on the hole punch Podpeh Uhb Sjfx Af Sorf - Various additional tool holders - Various replacement blades - Extensive accessories

Condition: used, machine/vehicle number: PA 1107, flat steel capacity: 80 x 10 mm electrical connection: 380 V, 1,3 kW space needed: 1000 x 650 x 1480 mm weight: 400 kg Prjdjby Dq Rspfx Af Sjf

Condition: used, Year of construction: 1979, round bar steel 28 mm square edge steel 25 mm Pedpfx Asvw Dvlof Sorf L-beam 80 x 8 mm cutting capacity 35 t shear : steel sheet max. 10 mm shear: flat material 100 x 11 mm blade length 175 mm triangle notching device for sheet until 8 mm no. of strokes max. 35 Hub/min work stroke ca. 35 mm total power requirement 1,5 kW weight of the machine ca. 535 kg dimensions of the machine ca. 0,97 x 0,45 x 1,55 m Motorized 4-way profile steel shear on a rotating base and mobile. The machine can also be used for hole punching by purchasing a hole punching device (instead of a notcher). Photo 5 shows which tools the punching device can optionally be equipped with. All performance specifications refer to a material strength of 450N/mm². Machine dealer with own stock of 1600 m².

Condition: used, Year of construction: 1983, round bar steel 50 mm square edge steel 40 x 40 mm L-beam 140 x 13 mm Punch power 900 kN hole punching press: throat 510 mm hole punching press: max. length of stroke 29 mm hole punching press: capacity (dia. x thick.) 31 x 20 mm notching: l + T material 80 x 14 mm no. of strokes 40 / 45 Hub/min total power requirement 4 kW weight of the machine ca. 3,7 t dimensions 2,1 x 0,7 x 2,12 m Psdpovh I T Nsfx Af Sorf Accessories: various punches and dies

Condition: used, Year of construction: 1976, round bar steel 28 mm square edge steel 25 mm Pjdpswm Rmnjfx Af Sjrf L-beam 80 x 8 mm notching cap. mild steel max. 7 mm cutting capacity of the vertical shear 350 kN Punch power 190 kN shear: flat material 100 x 11 mm shear: length of knifes ca. 175 mm total power requirement 1,5 kW weight of the machine ca. 0,5 t dimensions of machine L x W x H 1,0 x 0,5 x 1,5 m

Year of construction: 1970, condition: good (used), machine/vehicle number: FF 16, Offer 22226 Technical data: - Pressure capacity 50 T - throat approx. 360 mm - installation height approx. 240 mm - drive 400 V / 7,5 kW - perforates in ST 40 e.g. up to 25 mm Ø in 16 mm - up to 20 mm Ø in 19 mm - space requirement approx. W 1000 x H 1900 x D 1000 mm - weight approx. 1800 kg Prodpfx Afeit T Hye Sjf

Condition: used, functionality: fully functional, ---IMS PHY 1100 PUNCHING MACHINE, YEAR 2008, MAX PUNCHING 32X26 mm. Overall dimensions 185X75X210(h) cm, Machine weight 1800 kg ---IMS HY 45 VS PUNCHING MACHINE YEAR 2005 Hydraulic single punch Power 45 ton 5 work stations (slotting, angular cutting, bar cutting, shearing) Punching diameter 32 mm X 12 mm Slotting 50X40 x 6 mm 90 degree angular cutting 80 mm X 80 mm X 8 mm Plates 300 mm X11 mm Swan neck 170 mm Controlled or free descent Self-moving extractor Adjustment of punch upper dead point Psdpfxown Hu Rs Af Sorf Check squares Motor power 4 kW Overall dimensions 100X60X180(h) cm, Machine weight 500 kg

Condition: new, working width: 5020: ca. 140: Drehstrom 230 V / 400 V - 1,5bending angle (max.): 180bending length: 5020 - HIGH PROFITABILITY - FULLY HYDRAULIC - HIGH QUALITY STEEL - EVEN CONTACT PRESSURE - HAND CUTTER - WITH PROFILING DEVICE Prederzx Ebepfx Af Sef - ELECTRONIC ANGLE ADJUSTMENT The RULI long folding machine is the ideal machine for plumbers and large and small sheet metal processing companies. It is particularly characterized by its simple and sophisticated design and is not susceptible to repairs. The RULI long bending machine works fully hydraulically; clamping and bending are each controlled with a small lever. The pendulum-mounted and vertically closing upper beam enables contact pressure to be evenly distributed over the entire length and prevents the sheet metal from shifting during clamping. 2 degree scales allow you to read and adjust the individual bending angles. The machine is installed on a concrete floor or ceiling (min. 12 cm).

Condition: new, working width: 4010: ca. 140: Drehstrom 230 V / 400 V - 1,5bending angle (max.): 180bending length: 4010 - HIGH PROFITABILITY - FULLY HYDRAULIC - HIGH QUALITY STEEL - EVEN CONTACT PRESSURE - HAND CUTTER Prjdpfx Afsrzx D No Sef - WITH PROFILING DEVICE - ELECTRONIC ANGLE ADJUSTMENT The RULI long folding machine is the ideal machine for plumbers and large and small sheet metal processing companies. It is particularly characterized by its simple and sophisticated design and is not susceptible to repairs. The RULI long bending machine works fully hydraulically; clamping and bending are each controlled with a small lever. The pendulum-mounted and vertically closing upper beam enables contact pressure to be evenly distributed over the entire length and prevents the sheet metal from shifting during clamping. 2 degree scales allow you to read and adjust the individual bending angles. The machine is installed on a concrete floor or ceiling (min. 12 cm).