Veneer press

Joos HP 90 with 2 intermediate plates

Condition: good (used), Year of construction: 2002, operating hours: 5,900 h, functionality: fully functional, machine/vehicle number: 74343, working width: 1,350 mm, grinding belt length: 2,620 mm, grinding belt width: 1,370 mm, Wide belt sander Bütfering Optimat SBC 313 Year of manufacture: 2002 Kedjqvl D Hspfx Af Sjfa Model: Optimat SBC 313/QCE/Classic - with 3 units (see attached photo for description) - sanding from above Working width: 1350 mm Abrasive belt width: 1370 mm Abrasive belt length: 2620 mm Cross belt width: 150 mm Cross belt length: 4700 mm For more detailed information, see the photos

Condition: used, Year of construction: 1997, - edge banding unit - Cross-cutting unit - Milling unit Kfedpfed Inktex Af Ssa - Fine trimming unit - scraper - buffing unit

Condition: good (used), overall weight: 5,000 kg, working width: 1,300 mm, plate width: 1,350 mm, Bürkle U140 Veneer Press 4 intermediate plates Plate dimensions: 3050 x 1350 mm Working dimensions: 3000 x 1300 mm 8 hydraulic cylinders Ksdsxn Um Espfx Af Sjfa Max. surface pressure: 5 kp/cm2 Max. operating pressure: 348 bar Heating medium – hot water from central heating Cooling – cooling circuit with WILO pump, expansion tank, piping Weight approx. 5000 kg Plates and hydraulics in good technical condition

Condition: ready for operation (used), Year of construction: 2005, functionality: fully functional, Single-sided edge banding machine Manufacturer: Brandt Model: KDF 660 Year of manufacture: 2005 Max. edge thickness: approx. 12 mm Max. workpiece thickness: 60 mm Max. coil material thickness: 3 mm Kfsdpfx Afjxl Ufvs Ssa Equipped with: - Pre-milling unit - Coil magazine - Glue application unit - End trimming unit - Top/bottom flush and radius milling - Top/bottom radius milling with front/rear edge copying - Radius scraper - Buffing station Feed speed max. approx. 16 m/min. Connection: 400 V, 50 Hz, 3 Ph Total connected load: approx. 15 kW

Condition: ready for operation (used), Year of construction: 2000, functionality: fully functional, Dowel drilling machine Make Vitap Type Forma 63 H year 2000 with 3 units Kodpfx Afjuf Dmus Sjfa 2x bottom 1 x lateral with 21 spindles Pneumatic

Condition: used, Year of construction: 2004, Used machine Year of manufacture: 2004 with gluing unit for hot-melt adhesive granules Glue reservoir located below the glue roller Glue application to the workpiece via glue roller in both co-rotating and counter-rotating modes automatic edge magazine for coil material and fixed lengths Pressure zone with pneumatically-driven main pressure roller and special post-pressure rollers to compact the upper and lower glue joint Centrally adjustable upper pressure Central manual chain conveyor lubrication Control panel at machine infeed Kjdpfxsxya Rte Af Ssfa End trimming unit (saw aggregates) for front and rear edge overhang with high-precision linear guides 2 motors, each 0.18 kW Swivel range for straight and bevel cutting 0–15 degrees Flush-milling unit, top and bottom, with vertical and horizontal tracing Swivel range 0–15 degrees with 2 milling motors, each with replaceable insert cutter combinations (straight/radius) Digital counters enable rapid and precise, i.e., repeatable, settings Two-point pneumatic adjustment for upper and lower milling motors Scraper unit for finishing processing with horizontal/vertical tracing Support table extendable up to 350 mm Integrated section control for contactless operation of processing functions. Settings via keyboard and LED display Workpiece thickness: 8–50 mm Edge thickness: 0.4–3 mm Feed speed: approx. 9 m/min Connected load: 4.1 kW Compressed air connection: 6 bar Weight: approx. 750 kg Machine length: 3,150 mm Availability: short term Location: Flörsheim

Condition: defective spare-parts repository (used), Year of construction: 2007, functionality: limited functionality, Machine was fully working condition in 2021. Then dismantled and stored in warehouse. LEFT side Kjdoxu H S Tepfx Af Sefa

Condition: used, machine/vehicle number: AN004439, Anzahl Bohrspindeln : 2 Stk Teilung : 32 mm Bohreraufnahme : Schnellspannfutter Bohrerschaft: 10 mm Bedienung : Fußpedal Werkzeuge : Ja mm Bohrrichtung : von unten & stirnseitig max. Durchlasshöhe : 60 mm Anzahl Materialspanner : 2 Stk Art der Materialspannung : pneumatisch Ausführung : stationär Anschlagsystem : für Lochreihe und Konstruktionsreihe Kfedpfx Ajuuu Rkef Sea Gewicht ca. : 300 kg Motorleistung : 2+3 PS

Condition: good (used), LPG forklift KOMATSU FG45T-7, no. 107498, year of manufacture 2006, lifting capacity 4,500 kg, lift height 330 cm, mast height approx. 220 cm (duplex mast), hydraulic side shift, unladen weight 6,840 kg, with fork extensions, 120 operating hours (displayed, likely incorrect, actual operating hours unknown). Ksdpfxoxcni Ne Af Sefa