Dübellochbohrautomat

SCM MB 63

Year of construction: 1995, condition: good (used), 3 drilling heads with 21 spindles each 1 horizontal 21 spindles 2 vertical 21 spindles pneumatic clamps Nwodpfxsih H Eps Af Ser

Condition: used, Year of construction: 1997, - edge banding unit - Cross-cutting unit - Milling unit - Fine trimming unit - scraper - buffing unit Nsdpfxed Inkts Af Sowr

Condition: used, Year of construction: 1999, functionality: fully functional, overall weight: 600 kg, number of spindles: 21, SCM MB 63 multi-spindle drill, 21 spindles, 1.5 kW power, fully functional Nwedpexqx U Ejfx Af Sjr

Condition: good (used), Year of construction: 2002, operating hours: 5,900 h, functionality: fully functional, machine/vehicle number: 74343, working width: 1,350 mm, grinding belt length: 2,620 mm, grinding belt width: 1,370 mm, Wide belt sander Bütfering Optimat SBC 313 Year of manufacture: 2002 Model: Optimat SBC 313/QCE/Classic - with 3 units (see attached photo for description) - sanding from above Working width: 1350 mm Abrasive belt width: 1370 mm Nsdpeqvl D Hefx Af Sewr Abrasive belt length: 2620 mm Cross belt width: 150 mm Cross belt length: 4700 mm For more detailed information, see the photos

Condition: good (used), overall weight: 5,000 kg, working width: 1,300 mm, plate width: 1,350 mm, Bürkle U140 Veneer Press 4 intermediate plates Plate dimensions: 3050 x 1350 mm Working dimensions: 3000 x 1300 mm 8 hydraulic cylinders Max. surface pressure: 5 kp/cm2 Nwedpfjxn Um Eox Af Sor Max. operating pressure: 348 bar Heating medium – hot water from central heating Cooling – cooling circuit with WILO pump, expansion tank, piping Weight approx. 5000 kg Plates and hydraulics in good technical condition

Condition: ready for operation (used), Year of construction: 2005, functionality: fully functional, Single-sided edge banding machine Manufacturer: Brandt Model: KDF 660 Year of manufacture: 2005 Max. edge thickness: approx. 12 mm Max. workpiece thickness: 60 mm Max. coil material thickness: 3 mm Equipped with: - Pre-milling unit - Coil magazine - Glue application unit - End trimming unit - Top/bottom flush and radius milling - Top/bottom radius milling with front/rear edge copying - Radius scraper Njdpfoxl Ufvjx Af Sewr - Buffing station Feed speed max. approx. 16 m/min. Connection: 400 V, 50 Hz, 3 Ph Total connected load: approx. 15 kW

Condition: ready for operation (used), Year of construction: 2000, functionality: fully functional, Dowel drilling machine Nwedpfsuf Dmusx Af Ser Make Vitap Type Forma 63 H year 2000 with 3 units 2x bottom 1 x lateral with 21 spindles Pneumatic

Condition: used, Year of construction: 2004, Used machine Nwjdpfx Afsxya Rtj Sjr Year of manufacture: 2004 with gluing unit for hot-melt adhesive granules Glue reservoir located below the glue roller Glue application to the workpiece via glue roller in both co-rotating and counter-rotating modes automatic edge magazine for coil material and fixed lengths Pressure zone with pneumatically-driven main pressure roller and special post-pressure rollers to compact the upper and lower glue joint Centrally adjustable upper pressure Central manual chain conveyor lubrication Control panel at machine infeed End trimming unit (saw aggregates) for front and rear edge overhang with high-precision linear guides 2 motors, each 0.18 kW Swivel range for straight and bevel cutting 0–15 degrees Flush-milling unit, top and bottom, with vertical and horizontal tracing Swivel range 0–15 degrees with 2 milling motors, each with replaceable insert cutter combinations (straight/radius) Digital counters enable rapid and precise, i.e., repeatable, settings Two-point pneumatic adjustment for upper and lower milling motors Scraper unit for finishing processing with horizontal/vertical tracing Support table extendable up to 350 mm Integrated section control for contactless operation of processing functions. Settings via keyboard and LED display Workpiece thickness: 8–50 mm Edge thickness: 0.4–3 mm Feed speed: approx. 9 m/min Connected load: 4.1 kW Compressed air connection: 6 bar Weight: approx. 750 kg Machine length: 3,150 mm Availability: short term Location: Flörsheim

Condition: defective spare-parts repository (used), Year of construction: 2007, functionality: limited functionality, Machine was fully working condition in 2021. Then dismantled and stored in warehouse. LEFT side Nwjdpsxu H S Tefx Af Ser

Condition: good (used), pressing force: 95 t, cylinder diameter: 90 mm, plate width: 1,350 mm, Veneer Press Joos Type: HP 90 with 2 intermediate plates, stacking automaton, and lift table Pressing area: 2,550 x 1,350 mm Intermediate plates: 2 pcs. Pressing pressure: 95 t Piston diameter: 90 mm Specific pressing pressure: 2.75 kg/cm³ Number of cylinders: 4 Heating medium: hot water Total power: 1.3 kW Safety device: emergency stop rope Nsdpfexnqq Hjx Af Sjwr Press dimensions: 3,000 x 1,530 x 2,200 mm Press weight: approx. 4 t Elkom heating plates in very good condition Scissor lift table The plates are stacked and thus unloaded automatically.