Gurutzpe Super BT lathe 700 x 6000mm

Gurutzpe Super BT 700/6000

Condition: used, Technical details: turning diameter over bed: 1200 mm Lodjzuyfaepfx Adcehn turning diameter over support: 800 mm turning length: 3200 mm length of gap: 600 mm center height measured in bed: 600 mm turning dia. in gap: 600 mm spindle turning speed - continuous: 4,6-545 / 22 steps U/min spindle passage: 90 mm feed: 1,4-510 m/min taper: MK6 total power requirement: 15 kW weight of the machine ca.: 10,0 t dimensions L x W x H: 6,20x2,00x1,80 m dimensions electric cabinet LxWxH: 0,55x0,33x1,0 m equipped with: face chuck diameter 1000m (4 jaw chuck) fourfold chisel taper steady rest closed, inside diameter 250mm revolving tail center conical turning device *

Condition: used, Table unit from a DROOP & REIN portal milling machine Clamping plate with T-slots made of cast steel gray cast iron Table unit with clamping plate and very solid guideway Table clamping surface 5500 x 2000 mm Travel of the table clamping plate approx. 3100 mm Table height 1050 mm Table load: max. 20 tons Ball screw: Ø 100 mm Thread pitch: 20 mm (single-start) - Processing table guided very stably on the bed - Metal telescopic guideway cover - comes from a DROOP & REIN portal milling machine - Longitudinal table movement via ball screw and SIEMENS servo motor - Clamping surface with 11 T-slots 28 mm - Drive via SIEMENS 1FT6134-6AB71-1AG2 servo motor with IC200448S/R encoder (RN 000 B25) Total length 9500 mm Width 2000 mm Overall height 1050 mm dead weight 28 ton. good condition Ledpfsthuzpox Adcohn

Condition: excellent (used), functionality: fully functional, machine/vehicle number: 70.0961.000.253, TECHNICAL DETAILS: Turning diameter: - Over bed: 800 mm - Over carriage: 560 mm - Diamter of face plate: 750 mm Height of centers: - Over flat ways: 380 mm - Over Vee ways: 358 mm Gap, bed and gap piece: - Turning diameter in gap: 980 mm - Width of gap in front of face plate: 380 mm - Swing in gap: 1040 mm - Width of gap in front of face plate within swing diamter: 330 mm - Width of bed: 560 mm Headstock spindle: - Diameter of spindle bore: 90 mm - Spindle diamteres in front bearing: 145 mm - Taper in spindle: 6 Morse Spindle speeds: - Number: 18 - Spindle speed ranges: 7,1 - 355 RPM 9,0 - 450 RPM 11,2 - 560 RPM Power required: 7,5 - 14 kW Feeds: Lhsdpoup A Rzsfx Adcsn - Number: 32 - Sliding feeds per revolution: 32 longitudal feeds: 0,071 - 2,5 mm/rev. 32 cross feeds: 0,04 - 1,4 mm/rev. Extras: additional equipment, manuals for machine

Condition: used, Year of construction: 1980, turning diameter over bed 1930 mm turning diameter over slide rest 1520 mm turning length 5000 mm turning speeds 0,5-250 U/min Lodpfjyutp Hsx Adcshn spindle bore 105 mm workpiece weight 35 t steady 400-700 mm steady 700-1200 mm steady 1000-1600 mm control Siemens total power requirement 106 kW The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: new, Year of construction: 2026, Container rotating device, welding table, welding rotary table, roller stand 1000 kg load capacity Distance and rollers adjustable with foot-operated remote control Speed continuously adjustable from 80 to 1600 mm/min. Lhodpfx Aegu Edvjdcon Diameter 20 mm to 700 mm.

Condition: excellent (used), Year of construction: 2019, machine/vehicle number: 32006, input voltage: 480 V, The Sprinter for Gears with Short Face Widths up to 100 mm The 100S Gear Shaping Machine is ideally suited for small face widths, for shaping spur and helical gears, internal and external, and for crowned and tapered gears. With only 6 m2 the 100S is one of the most compact machines of its class. Equipped with: Siemens Sinumerik 840D SL Control Hydraulic System 180 Degree Load System HSK-63 Spindle Auto Stroke Adjustment Chip Conveyor Chip Basket Flexlink Automation Festo Pneumatics Rittal Panel Conditioners Chiller 480/3/60, 35 KvA Motor & Controls Specifications: Workpiece With External Gear: -Largest Module (Steel W/Approximate 600 N/mm2): 3 mm -Maximum Width: 26 mm -Maximum Diameter: 100 mm Workpiece With Internal Gear: -Largest Module (Steel With Approximate 600 N/mm2): 3 mm -Maximum Width: 26 mm -Maximum Swing Diameter: 150 mm -Maximum Internal Diameter: 100 mm Tool: -Locating Cone In The Cutter Spindle: HSK-D63 -Diameter Shaping Spindle: 85 mm -Maximum Stroke Length: 30 mm Machine Travel Distances: -Radial (X-Axis): 180 mm -Column Tilting (B-Axis): -1 - +11 Degrees Machine Workpiece Table: -External Diameter: 220 mm -Clamping Diameter: 160 mm Ljdpfx Adjrtrvyocohn -Bore: 63 mm Speeds: -Feed Rate X-Axis: 12,000 mm/min -Workpiece Table (C-Axis): 0-400 min-1 -Cutter (C2-Axis): 0-300 min-1 -Spindle Stroke (A-Axis): 500-3,000 min-1 Electrical Equipment: -Operating Voltage: 480V -Supply Voltage: 115V -Control Voltage: 24V -Frequency: 60 Hz -Connected Load of Machine: 35 kVA -Cable Cross-Sectional Area: 35 mm2 -Protection: 80 A Machine Overall Dimensions (L x W x H): 3,380 x 3,950 x 3,015 mm Weight of Machine: 7,800 kg

Condition: new, travel distance X-axis: 2,000 mm, travel distance Y-axis: 1,200 mm, travel distance Z-axis: 800 mm, feed rate X-axis: 30,000 m/min, feed rate Y-axis: 30,000 m/min, feed rate Z-axis: 30,000 m/min, table length: 1,900 mm, table width: 1,100 mm, spindle speed (max.): 6,000 rpm, table load: 4,000 kg, position of the milling head: Vertikal, torque: 1,356 Nm, spindle nose: SK 50 - DIN 69871A, Equipment: rotational speed infinitely variable, The STARVISION DH 2012 impresses with its robust portal design, powerful drives, and high-quality components. It offers high precision, rigidity, and reliable machining – even for demanding machining tasks. Ideally suited for mold making, machine construction, and contract manufacturing. Your advantages: ✔ Installation and commissioning in Germany included ✔ Service and spare parts directly from JMT ✔ Financing and lease-purchase options available ✔ 24 months warranty Technical features: Control: ✔ HEIDENHAIN TNC 7 control ✔ HEIDENHAIN TFT screen 19" ✔ HEIDENHAIN motors, measuring systems, and electronic handwheel Cooling: Internal coolant supply (IKZ) 70 bar Tool changer: 60-position chain magazine with double gripper Chip removal: Hinged belt chip conveyor (transverse) Double screw conveyor (longitudinal) Preparation: Preparation for 4th axis (rotary table) Ljdpfoq Ixc Tjx Adcohn Enclosure: Full enclosure, closed at the top Accuracy: Positional accuracy: ± 0.025 mm Repeat accuracy: ± 0.020 mm Contact us – we will be happy to advise you and prepare an individual offer for you.

Condition: good (used), Year of construction: 2005, Mazak Integrex 300 - III turning/milling center, year of manufacture 2005, CNC control 640 MT, travel X/Y/Z 630/230/1,585 mm, B axis NC swiveling head -30°/+195°, tool magazine with 80 positions Capto, main spindle 26 kW, C axis 0.001°, tailstock MK 5, high-pressure coolant system 70 bar with filtration unit, Tooleye, 5-axis simultaneous machining package, Mazak Monitoring System, chip conveyor, Ljdpfx Aeyzfr Isdcohn

Condition: ready for operation (used), Pressing force: 1600kN, throat depth: 450mm, installation height: 560mm, ram stroke: 8-160mm, controls: SCHMERSAL SEPG 05.3.2.0.22/ 95, weight: 16.2t, including documentation. Lhodehz Ua Sepfx Adcjn

Condition: new, table diameter 900 mm table load 1,0 t swivelling range 135 Grad turning speeds 0,12 - 1,2 U/min 820 mm Lhedpsfv Axxsfx Adcsn welding current 500 Ampere total power requirement 0,75 + 0,55 kW weight of the machine ca. 1,1 t dimensions of the machine ca. 1,5 x 1,0 x 0,9 m • Self-locking gear, therefore no forward and backward at eccentric Load. • Electronic components from Schneider, Siemens and Delta. • Frequency-controlled stepless speed of the turntable. • High stability due to the robust construction. • welding power transmission • CE certificate. • Very good price / quality ratio. • The D-HBE series comes as a standard version with a cable remote control and delivered with a footswitch.