Double-column hydraulic press

EXNER EXSBZR 450

Condition: good (used), Year of construction: 1998, Press Force 315.00 t Stroke 500 mm Throat 425 mm Installation Height (Upward Stroke) 1,000 mm Lsdpfx Aov Rwu Uji Reag Table Surface 1,200 x 815 mm Table Height above Floor 800 mm Ram Surface 1,100 x 700 mm Speed Down 48 mm/s Speed Up 330 mm/s Working Speed 19 mm/s Oil Volume 1,600 l Power Requirement 82.0 kW Weight 23.00 t Dimensions (WxDxH) 2.4 x 2.8 x 4.0 m For Permitted for manual loading according to the CE standard with oil-hydraulic drive, controllable depending on pressure/time and travel, light-guard at the front (Sick), two-hand operation permitted for manual loading according to the CE standard with oil-hydraulic drive, controllable depending on pressure/time and travel, light-guard at the front (Sick), two-hand operation

Condition: used, Year of construction: 1996, pressure 80 t throat 320 mm stroke 6 - 118 mm no. of strokes 30 - 80 Hub/min ram adjustment 70 mm table surface area 830 x 610 mm ram surface 650 x 400 mm column daylight (nach hinten) 630 mm total power requirement kW weight of the machine ca. 8,1 t dimensions of the machine ca. B 1,2 x T 1,9 x H 3,3 m Furnishing: - with gear transmission - fixed table - automatic stroke adjustment Lajdpfxstycdks Ai Rjg - automatic ram adjustment - hydr. Overload - Ejector - Grease central lubrication - Cover plate for drainage hole - Continuous speed control using a frequency converter - Machine is technically checked in our company and receives a new control cabinet with safety controls and touchscreen - current UVV test with braking time measurement

Condition: used, Single-column – Eccentric press WEINGARTEN Type EV 63 Machine No. 738 / 61 Year of manufacture 1962 Lajdpfx Ajk S Htxei Rjg Pressing force 63 tons Stroke 260 mm Table area 630 x 530 mm Table opening Ø 210 mm Slide area 315 x 260 mm Adjustable slide stroke 8-100 mm Slide adjustment 63 mm Tool holder bore Ø 40 mm, with clamping piece Installation height max 450 mm Stroke rate 115 strokes / min Compressed air requirement min. 4.5 bar Motor power 4 kW Power connection 380 Volt, 50 Hz Table height above floor approx. 750 to 900 mm - Electrical stroke release via foot switch or two-hand control - Overload protection by shear plate - Clutch-brake combination by WEINGARTEN friction-thread clutch with top dead center through-drive protection - Front crankshaft support bearing - Press table adjustable in height via 2 threaded spindles - Manual centralized lubrication - Control cabinet positioned beside the press - UVV (German trade association for accident prevention) for manual feeding operations Space requirement L x W x H 1750 x 1600 x 2430 mm Weight 4.5 tons Good condition

Condition: good (used), Year of construction: 1998, functionality: fully functional, ram adjustment: 40 mm, installation height: 2,400 mm, total width: 17,000 mm, table length: 400 mm, table width: 400 mm, pressing force: 25 t, stroke adjustment: 17 mm, working width: 200 mm, overall weight: 2,500 kg, year of last overhaul: 2023, power: 0.003 kW (0.00 HP), Make: MABU Model: 25 VPR. Made in Germany. Max. Pressure: 250 [kN] (25 [T]). Speed range: 80-400 [spm]. Completely rebuilded Dec. 2023 Year of manufacture: 1998. Operating modes: Manual, One-cycle and Automatic. Equipped with two hand start and foot-clamp start. Fixed stroke: 17 [mm]. Ram adjustment: 40 [mm]. Max. Tool dimensions: 400 x 400 [mm]. Power: 3 [kw]. Current: 230 / 400 [V]. Air connection: 5.5 [bar]. Feeder: Silicon SFS 200 on left-hand side. Max. strip width: 200 [mm]. Machine dimensions: H 2350 x W 1700 x D 1400 [mm]. Ledpfxsq Ikhpo Ai Reag Weight of machine: cca. 2500 [kg]. Electrical cabinet with Mabu Pf 1.3 control. Front and rear safety guards with inspection glass. Technical documentation and operating instructions in English and German included. CE certificate and EUR-1 certificate of origin. On stock, tested and ready for delivery. More used machines from Mabu, Bruderer, Bihler and Schaal available on our stock for sale.

Year of construction: 2002, condition: used, pressure 130 t throat 350 mm Lodpolp U Dlefx Ai Rsag stroke 16-200 mm no. of strokes 55 Hub/min ram - range of adjustment 100 mm table surface area 1200x700 mm ram surface 730x530 mm hole in the table 300x210 mm table height 900 mm tool hole in ram Ø 50 mm weight of the machine ca. 8,0 t dimensions of the machine ca. BxTxH 1500x2200x3500 mm

Condition: used, Year of construction: 1997, Press capacity: 315 ton Ram stroke adjustable: 30 - 100 mm Slide adjustment: 100 mm Shut height (stroke down, adjustment up): 370 mm Table surface area : 1600 x 1100 mm Slide area: 1600 x 1100 mm Hole in table: 600 x 180 mm Number of strokes: 15 - 180 s.p.m. Table height over floor: 1200 mm Required power: 170 kW Height over floor approx.: 4900 mm Dimensions L x W x H: 4900 x 1900 x 4900 mm Weight of machine approx.: 55 ton Standard configuration The press was converted to CE standard in press was 2021 converted to a SIEMENS S7 control conveyor system still has a SIEMENS S5 control system. Extended machine accessories Die lifters in the table Automation Feeding unit KEMMERICH consisting ofDecoiler levelling machine roll feeder Ljdpfxouqd Tme Ai Reag Coil loading car

Condition: used, Year of construction: 2021, machine/vehicle number: HB 2022-A-073, pressing force: 300 t, Portal straightening press with 300 T capacity a) idle and pressing speed up to 17 mm/sec. b) opening speed up to 55 mm/sec c) table size 2500x1600mm d) open height 700 mm e) total size approx. LBH 4500 x 2300 x 3700 mm f) Oil temperature indicator on the tank g) Lubrication via grease nipple h) table in grid construction,with T grooves according to customer's request, otherwise 22mm i) operation on swivel arm, mounted on the bridge j) pressure adjustment from 50 T to 300 T via MONITOR k) bridge moves by two gear motors, via racks l) Cylinder moves to the left and to the right via toothed racks m) Machine body double painted n) Cylinder induction hardened Type of construction Press design PORTAL PRESS Thermally neutral 80 - 120 °C Number of operating sides 3 side Forces Pressing force max. 3,000 kN Free ripping force max. 500 kN Pressure build-up time Closed die Steel to steel Max. 3 sec. Dimensions Max. Opening width 700 mm Stroke and min. opening 700 mm/ 0 mm Table height above floor approx. 9ß0 mm Height above floor (headroom) approx. 3700 mm Hall height min. 5.000 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.8 mm/m Weight Total weight of press without operating materials and table plate approx. 22 T Speeds Fast closing with 17 mm sec. Pressing speed 8 mm sec. Opening 55 mm sec. Sound pressure Sound pressure level, measured at 1.5m height at the control panel after max. 78 db(A) DIN 45635-T16-KL3 Hydraulics Number of pressing cylinders 1 pc. Operating pressure max. 350 bar Pressing pressure build-up time 02. mz sec. Pressure accuracy during pressing stroke +/- 5 bar Main pump BOSCHREXROTH approx. 93 L/min Oil volume approx. HLPD 46 MW 900 liters Ambient temperature max. 45 °C Lodpfx Ash Agnuji Roag Oil temperature max. 55 °C Electrical system Main supply 400 V AC Control voltage 24 V DC Frequency 50 Hz Hydraulic connection Main motor IE3 22 kW Total connection Approx. 30 kW

Condition: new, column width: 2000 x 1000retracting speed: 150weight approx.: 35.000stroke: 800total power requirements: 30daylight: 1000rapid traverse: 120pressure: 500: 2500 x 1500working speed: 12messurements (LxWxH): 2500x2700x5400 Laodpfed Aca Aex Ai Rog

Condition: used, Year of construction: 1979, Technical details: Lsdpfx Aju Nfinji Roag pressure: 250 t slide stroke: 40-160 mm throat: 545 mm ram adjustment: 110 mm Table dimensions: 1250x800x100 mm biggest distance between table & ram: 670 mm drawing capacity: 16 to table height over floor: 1000 mm surface area of ram: 900x670x100 mm distance between columns: 500x400 mm total power requirement: 23 kW weight of the machine ca.: 16,6 t dimensions of machine: 2,8x1,4x3,7 m dimensions electric cabinet LxWxH: 1,15x0,6x2,1 m Ejector and counter holder force: 16t Table size with 4x T-slots parallel running (1250x800x100mm) Ram plate with 4x T-slots radially running Data at bottom dead center UT: largest stroke: 510mm smallest stroke: 570mm Accessories: - Steel plate 1170x860x80mm *

Condition: good (used), Year of construction: 1977, functionality: fully functional, power: 15 kW (20.39 HP), pressing force: 200 t, table width: 800 mm, table length: 1,100 mm, throat depth: 440 mm, distance table to ram: 400 mm, total length: 37,200 mm, total width: 24,000 mm, total height: 18,200 mm, overall weight: 12,600 kg, ram adjustment: 110 mm, ram stroke: 40-180 mm incl. Helmerding feed, 400 mm x 4 mm Strokes: 40 + 60 1/min Lajdpjtu Hvwefx Ai Reg Distance table/ram - adjustment top/stroke bottom: 400 mm Table opening: 450 mm diameter