DEMAG

Condition: ready for operation (used), Year of construction: 2003, operating hours: 96,986 h, clamping force: 600 kN, screw diameter: 30 mm, This DEMAG ET60-200 concept hydraulic injection moulding machine was manufactured in 2003. It features a clamping force of 600 kN and a maximum mold weight of 580 kg. The machine includes a robust injection unit with a screw diameter of 30 mm and an injection pressure of 1900 bar. Consider the opportunity to buy this DEMAG ET60-200 concept hydraulic injection moulding machine. Contact us for further details. • Clamping unit: • Tie bar spacing (H x V): 420 x 420 mm • Platen dimensions (H x V): 530 x 540 mm • Min. mold installation height: 210 mm • Opening stroke: 400 mm • Max. mold weight: 580 kg (moving side 380 kg / fixed side 200 kg) • Ejector: • Stroke: 125 mm • Force: 41 kN • Retraction force: 15 kN • Pneumatic ejector: Yes • Core pull control: Yes (2 units, on the ejector side/AS) • Injection unit 1: • Unit size: 200 • Screw diameter: 30 mm • Injection pressure: 1900 bar • Stroke volume: 106 ccm • Shot weight (PS): 94 g • Screw L/D: 20 • Nozzle radius: 15 mm • Armored/wear-resistant injection unit: Yes • Process control: SPC (Yes) • Note: Maximum crane load warning: 2 metric tons Additional equipment Fedpfx Afsyg Nfujujpd • Robot/removal device: W621-1381 • Travel paths: Y 1200 mm, X 550 mm, Z 1500 mm • Hot runner controller: 7-zone integrated control • Mold sensors: Kistler (p=1/t=0)

Condition: ready for operation (used), Year of construction: 2013, operating hours: 27,551 h, clamping force: 2,200 kN, total height: 2,100 mm, This SUMITOMO SHI DEMAG IntElect 220/610-750 smart was manufactured in 2013. It's an electrical injection moulding machine known for its precision and efficiency. Ideal for those looking to enhance their production capabilities with reliable technology. Contact us for more information. Additional equipment • Sepro Robot SDR 22 Machine Benefits Technical Machine Benefits • Screw diameter: 45 mm / screw geometry: standard / l/d ratio: 20 / specific injection pressure: 2150 bar / maximum shot volume: 329 cm³ / maximum shot weight: 293 g / injection rate without accumulator: 254 cm³/s Fedox D Hnyopfx Afuspd • Dosing stroke: 207 mm / maximum nozzle stroke: 450 mm / nozzle immersion depth: 20 mm / nozzle contact force: 58 kn / number of heating zones: 4 / hopper capacity: 50 l / maximum injection speed: 160 mm/s • Holding force: 2420 kn / maximum opening stroke: 550 mm / minimum mold height: 300 mm / maximum mold height: 580 mm / maximum platen distance: 1130 mm • Mold clamping plates (hxv): 880x830 mm / clearance between tie bars (hxv): 610x560 mm / ejector stroke: 150 mm / ejector force: 58 kn • Dry cycle time according to euromap 6 (stroke): 427 mm • Net weight without oil: 10100 kg Dimensions Machine Depth 6460 mm

Condition: ready for operation (used), Year of construction: 2015, operating hours: 15,642 h, screw diameter: 45 mm, total height: 2,213 mm, overall weight: 15,750 kg, This SUMITOMO SHI DEMAG Systec SP 350/720-840 was manufactured in 2015. It is a hydraulic injection moulding machine, ideal for precision plastic processing. Consider the opportunity to buy this SUMITOMO SHI DEMAG Systec SP 350/720-840 hydraulic injection moulding machine. Contact us for more information. Additional equipment • Fanuc Robot Machine Benefits Qualitative Machine Benefits • Process data acquisition, mould protection Technical Machine Benefits • Mould height min: 350 mm / mould height max: 745 mm • Main electronic connection: 3/400 v 50hz • Programmable sequence, highly dynamic feed speed, hydraulic pressure-dependent holding pressure control, digital/wear-free position measuring system. Extra Information Standard equipment: Support of the moving mould mounting platen via linear guides/ Ejector short / long stroke/ Interface for external printer (hardcopy)/ Individual axis movement optimization (activeAdjust)/ Four-stage mould closing and four-stage mould opening sequence/ Pump drive power II, increased (59.0 kW)/ Mains voltage 400 V ±10% / 50 Hz, 3 phases + N + PE/ Mains connections drive / heating separate/ Data display coloured/ Oil cooler reinforced (cooling water supply up to 35 °C)/ Water connection for mould and machine cooling separate/ Basic version Europe/ Corrosion protection/ Paint finish: Deep black (RAL9005): Machine bed with internals, lower switch cabinet/ Signal white (RAL9003): Clamping unit, injection unit, nozzle guard/ Signal white (RAL9003): Fixed safety devices, upper switch cabinet/ Signal white (RAL9003): Safety doors/ Textured surfaces: Elastic machine bearings/ Digital and wear-free position measuring system (ultrasound/high-resolution rotary encoders for injection, mould and ejector movement)/ Fedpfxex D Hnto Afujpd Mould connection dimensions type E (according to EUROMAP March '96)/ Centring diameter fixed platen: 160 mm/ Centring diameter moving platen: 160 mm/ Without side ejector plate/ Standard mold installation height: Min: 350 mm/ Max: 745 mm/ Standard closing speed (movements only when safety gate is closed)/ Ejector with position control (p/F+v independently programmable, parallel to mold movement)/ Toggle lever oil lubrication/ Injection unit/ Optional equipment: Speed-controlled pump Servo Technology (activeDrive)/ Emergency stop switch on operator side/ Separate opener for ultra-fine filtering in the bypass (activeCool&Clean)/ Socket 1 x Schuko (230V / 10A), can be disconnected via main switch/ Socket IECEE 3Ph / 400V-16A, can be switched off via main switch/ Flashing light/ Operation with safety door open (operator side)/ 6 pneumatic 5/2-way valves on movable tool plate (programmable)/ 6 pneumatic 5/2-way valves on fixed tool plate (programmable)/ Central maintenance unit for pneumatic valves/ Core pull 1-circuit via proportional valve (programmable, with non-return valves)/ Manual pressure relief for core pull 1-circuit/ Protective clothing on operator side widened (250 mm)/ Hot runner control 12 zones, integrated (2, 75 kW)/ Pneumatic hot runner nozzle control (1x 5/2-way valve)/ Clamping force control/ Active mold protection via sensor when closing (activeQ)/ Manually adjustable monitoring switch for mold open position/ Central grease lubrication (manual)/ Material hopper for automatic filling/ Hopper shut-off with emptying option/ Holding pressure switchover dependent on hydraulic pressure (with pressure recording)/ Nozzle contact pressure when mold is open (programmable)/

Year of construction: 2019, operating hours: 17,716 h, condition: ready for operation (used), General Data Measurements width 1920 cm Measurements depth 7750 cm Machine weight 26210 kg Measurements height 2410 mm Fodex D Nx Iepfx Afuepd This SUMITOMO SHI DEMAG El-Exis SP 350/820-920 was manufactured in 2019. A robust electrical injection moulding machine with a screw diameter of 40 mm and a clamping force of 3,500 kN. It has operated for 17,716 hours with 12,440,761 cycles, ensuring extensive production capabilities. Consider the opportunity to buy this SUMITOMO SHI DEMAG El-Exis SP 350/820-920 electrical injection moulding machine. Contact us for more information. Application Types Injection Moulding

Year of construction: 2005, condition: ready for operation (used), This SUMITOMO SHI DEMAG El-Exis S 250/630-1450 was manufactured in 2005. It features a central accumulator for high-speed injection and chromed tie bars. The pump drive power is 22.0 kW, with a mains voltage of 400 V/50 Hz. It includes a color data display with VGA interface, an oil cooler, and electric screw drive. Consider the opportunity to buy this SUMITOMO SHI DEMAG El-Exis S 250/630-1450 hydraulic injection moulding machine. Contact us for more information. Fpsdsx D Rqropfx Afued • 5x similar units available • Central accumulator for high-speed injection; core, ejector, and nozzle movement • Nozzle movement parallel to mold movement • Chromed tie bars on clamping unit • Pump drive power: 22.0 kW • Mains voltage: 400 V / 50 Hz, 3 Ph + N + PE • Separate mains connections for drive and heating • Control: color data display with VGA interface and AT keyboard interface • Injection, holding pressure, and back pressure via servo valve • Reinforced oil cooler • Separate water connections for mold and oil cooling • Compliance: Basic version Europe, according to valid safety regulations • Painting: Bottom anthracite grey RAL 7016; Top blue 571C MD • Elastic machine mounting • Ultrasonic displacement measuring system with digital data transmission for injection, ejector, mold (WZ), and nozzle (AWH) movements; 1/100 mm resolution for injection axis • Reduced centering diameter (D=100/125) for fixed mold platen • Mold connection dimensions type E (similar to EUROMAP), without side ejector plate • Standard mold installation height • Safety interlock: mold opening and ejector forward only with closed safety door • Ejector with position control via proportional valve; pressure and velocity independently programmable • Electric screw drive, frequency-controlled

Year of construction: 2019, condition: ready for operation (used), This DEMAG Systec 210/580-840 was manufactured in 2019. It's a hydraulic injection moulding machine with a clamping force of 210 tons and a power output of 60 kW. It has been used for 31,132 operating hours. Consider the opportunity to buy this DEMAG Systec 210/580-840 hydraulic injection moulding machine. Contact us for more information. • The dosing unit (orange part) is not included. • Integrated socket combination, country-specific, • can be switched off via main switch and shutdown program • 2 x Schuko 1Ph/230V/16A; 2 x IECEE 3Ph/400V/16A residual current device • Pneumatic 5/2 valve No. 1 on movable mold clamping plate; • programmable, supplied via central air connection • includes hoses. Inputs and outputs freely programmable; 3 inputs and 3 outputs; • Terminal point outside the control cabinet • Interface for additional nozzle heating band; socket only • 2-circuit core puller via switching valve on movable mold clamping plate; Q-independent (programmable); • With pilot-operated check valves to prevent core creep • Mold connection dimensions E (similar to Euromap March 96) Fjdpjx D Nlusfx Afuepd • With side ejector plate, centering diameter of fixed platen: 160 mm • Centering diameter of movable platen: • Mold installation height increased by 100.0 mm • Min: 340 mm • Max: 790 mm

Condition: ready for operation (used), Year of construction: 2020, operating hours: 8,000 h, clamping force: 500 kN, screw diameter: 25 mm, injection weight: 46 g, total height: 1,779 mm, overall weight: 4,200 kg, This SUMITOMO SHI DEMAG Intelect 2 50/370-110 was manufactured in 2020. It features a fully electric direct-drive system, NC5+ control for enhanced energy efficiency, and precise injection dynamics. Includes a granule dryer, industrial robot, conveyor belt, and temperature units. Ideal for high-quality injection moulding processes. Contact us for more information about this machine. Additional equipment • Granule Dryer • Handling System • Conveyor Belt - 1400 mm x 400 mm • Precision Scale • Temperature Units - 2x HB‑Therm Machine Benefits Technical Machine Benefits • Exceptional energy efficiency • Enhanced platen rigidity and mold safety Fpjdpfxjx D Ecco Afujd • Fully electric direct-drive system • Ultra-precise direct-drive motors with 0. 1 ms response time • Displacement: 52 cm³ • Spray pressure: 2180 bar • Tool clamping platens: 520 x 570 mm Extra Information Control Unit Advanced control system with NC5+ Automatic mold height and clamping force adjustment Energy-saving routines Dimensions Machine Depth 4308 mm

Condition: ready for operation (used), Year of construction: 2013, operating hours: 17,577 h, clamping force: 1,600 kN, total height: 2,060 mm, This SUMITOMO SHI DEMAG IntElect 220/610-750 smart was manufactured in 2013. It's an electrical injection moulding machine known for its precision and efficiency. Ideal for those looking to enhance their production capabilities with reliable technology. Contact us for more information. Additional equipment • Sepro Robot SDR 11 Machine Benefits Technical Machine Benefits • Clamping unit: 160 / locking force: 1760 kn / opening stroke max: 495 mm / mould installation height, min: 275 mm / mould installation height, max: 585 mm • Platen distance, max: 1080 mm / mould mounting platens (h x v): 760 x 785 mm / clear column distance (h x v): 520 x 520 mm Fjdpex D Hnmjfx Afuspd • Ejector travel: 125 mm / ejector force: 35 kn • Injection unit: 340 / screw diameter: 35 mm / l/d ratio: 20 / injection flow (ps) without accumulator: 288 cm³/s • Metering stroke: 162 mm / nozzle stroke, max: 350 mm / nozzle immersion depth (svo): 20 mm / nozzle contact pressure: 30 kn • Material hopper capacity: 35 l / injection speed, max. , standard: 300 mm/s / injection speed, max. , increased: 500 mm/s • Net weight without oil filling: 7300 kg Extra Information Electrical & Pneumatic Interfaces: Sockets: 2 x Schuko (1Ph, 230V, 10A)/ 2 x IECEE (3Ph, 400V, 16A) – switched off via main switch/ Additional Schuko socket also listed (same rating)/ Valves: 1 x Pneumatic 5/2 valve on movable platen (programmable)/ 2 x Pneumatic 5/2 valves on stationary platen (programmable)/ I/O: 3 digital inputs / 3 digital outputs (freely programmable)/ Terminal board outside control cabinet/ Air & Cooling: Central air supply and piping/ Cooling system: open cycle/ Cooling water controller: 4 circuits with temperature indication (max. 10 l/min per circuit)/ Separate water connection for cooling (mould + machine)/ Switch-off for mould cooling (time programmable)/ Machine Mechanical & Motion Features: Clamp and injection unit colours: Jet black (RAL9005): bed, pump station, lower control cabinet/ Signal white (RAL9003): clamp unit, injection unit, guards, covers, safety doors/ Mould platen layout: E-standard (similar to EUROMAP, March 1996)/ No side ejector platen/ Ejector: held in front position against spring-loaded mold ejector/ Standard mold height/ Standard closing speed/ Only active movement when safety guard is closed/ Screw: wear-resistant, nitrided barrel, standard L:D, 35 mm diameter/ Non-return valve: 3-piece ring type/ Control, Programming & Monitoring: Inputs/outputs and clamp sequence: freely programmable/ Switching programs (e.g., dry cycle, startup scrap counter, timer-controlled cooling)/ Injection process: Injection force with max injection speed: 200 mm/s/ Back pressure programmable via 6-point polygon/ Follow-up pressure switch-over based on melt pressure/ Follow-up, back pressure, metering: closed-loop control/ Feed throat temp control: closed-loop, max 90°C ±9°C/ Reduced nozzle sealing force (programmable)/ Clamp force: closed-loop control/ Active mold protection: sensor-based during closing/ Hot runner control: 5 zones integrated (2.75 kW total) Display, Software & Data: Coloured data display PDA (Process Data Acquisition): 100% control with graphical parameter recording/ Overlaid graphs for multiple cycles/ External statistical data export/

Condition: ready for operation (used), Year of construction: 1995, operating hours: 122,158 h, clamping force: 3,300 kN, screw diameter: 60 mm, This DEMAG ET 330 - 1450 hydraulic injection moulding machine was manufactured in 1995. It features a clamping force of 3300 kN and a screw diameter of 60 mm, providing robust performance for various applications. The machine includes a Wittmann W322-121 linear robot for enhanced automation. Consider the opportunity to buy this DEMAG ET 330 - 1450 hydraulic injection moulding machine. Contact us for further details. • Clamping unit: • Locking force: 3630 kN • Tie bar spacing (H x V): 710 x 630 mm • Platen dimensions (H x V): 1040 x 950 mm • Mold installation height: min 330 mm / max 830 mm • Opening stroke: 675 mm • Platen distance (daylight): 1505 mm • Permissible mold weight: fixed side (DS) 1200 kg; moving side (AS) 2400 kg; total 3600 kg • Ejector: stroke 200 mm; force 80 kN; retraction force 35 kN • Core pull control: yes (2 units, on ejector side/AS) • Shut-off nozzle: yes (hydraulic/pneumatic 1/1) • Injection unit 1: • Unit code: 1450-60 • Screw diameter: 60 mm • Injection pressure: 1905 bar • Stroke volume: 763 ccm • Shot weight (PS): 695 g • Screw L/D ratio: 20 • Nozzle radius: 15 mm • Max dosing stroke: 270 mm Fjdpfjyg Nkwex Afujpd • Plasticizing flow: 41 g/s • Configuration/controls: • Armored (wear-resistant) injection unit: yes • Pneumatic ejector: yes • Process control: SPC (Yes/Yes) • Printer interface: integrated • Hot runner control: 0-zone (none) • Maintenance: • Hose replacement performed in 2017 Additional equipment • Wittmann W322-121 CNC linear robot/removal device (included with the machine) • Travel paths: Y-axis 1600 mm, X-axis 500 mm, Z-axis 2500 mm

Condition: ready for operation (used), Year of construction: 2004, operating hours: 91,810 h, clamping force: 2,500 kN, screw diameter: 60 mm, injection weight: 579 g, This DEMAG ET250/630-840 Concept was manufactured in 2004. It features a clamping force of 2500 kN and a locking force of 2750 kN. The machine includes a Wittmann linear robot and supports a maximum mold weight of 3300 kg. It's equipped with a screw diameter of 60 mm and offers a shot volume of 636 ccm. Consider the opportunity to buy this DEMAG ET250/630-840 Concept hydraulic injection moulding machine. Contact us for more information about this machine. • Locking force: 2750 kN • Tie bar spacing (H x V): 630 x 630 mm • Platen dimensions (H x V): 950 x 950 mm • Mold height: 330–830 mm • Opening stroke: 675 mm • Max daylight (distance between platens): 1505 mm • Mold weight capacity: fixed side 1100 kg, moving side 2200 kg (total 3300 kg) • Ejector: • Stroke: 200 mm • Force: 80 kN • Centering ring diameter: 200 mm Fpodpfx Afjyfq Aleujd • Pneumatic ejector: yes • Core pulls: 2 on moving side (AS) • Injection unit: • Unit size: 840 • L/D: 20 • Shot volume: 636 cm³ • Injection pressure: 1351 bar • Plasticizing rate (PS): 74 g/s • Screw speed: 326 rpm • Nozzle radius: 15 mm; nozzle bore: 3 mm • Max dosing stroke: 225 mm • Note: Second injection unit listed with no data → single-component machine • Interfaces/controls: • Printer interface: yes • Process control/SPC: yes Additional equipment • Robot/handling: Wittmann W633-961 linear robot • Stroke: Y (vertical) 1600 mm, X 900 mm, Z 2500 mm • Hot runner control: 9 zones • Mold sensing: Kistler pressure (p=1) / temperature (t=0) system • Valve gate control: hydraulic (pneumatic not equipped)