Used machining centers with flat or grid table for sale (341)

Condition: ready for operation (used), Year of construction: 2017, operating hours: 1,717 h, functionality: fully functional, machine/vehicle number: 904B0018, table width: 3,500 mm, table length: 14,400 mm, saw blade diameter: 1,000 mm, Equipment: CE marking, documentation/manual, TECHNICAL DETAILS Maximum saw blade diameter: 1,000 mm C1: 540° B1: 250° Lhedpsx Hg Stjfx Af Ssr C2: 540° B2: 90° Table length: 14,400 mm Table width: 3,500 mm X-axis maximum travel: 5,000 mm Y-axis maximum travel: 15,870 mm Z-axis maximum travel: 1,000 mm MACHINE DETAILS Number of milling spindles: 1 Number of controlled axes: 2 5-axis unit power: 12 kW Operating hours: 1,717 h Main motor power: 55 kW Voltage: 400 V Current consumption: 130 A Power: 65 kW Transport dimensions (L x W x H): 40,000 mm x 2,400 mm x 2,700 mm EQUIPMENT Saw blade unit with flange connection Milling unit with tool changer Documentation CE marking

Condition: used, machine/vehicle number: 008369, X axis working area: 3100 mm Y axis working area: 1600 mm Working Table: Flat table Main Electrospindle power: 10 KW Number of controlled axes: 4 axes Total number of drilling spindles: 14 Ljdpfx Aox A Tinjf Sehr Total number of tool changer positions: 6

Condition: excellent (used), Year of construction: 2016, machine/vehicle number: 0-250-95-3275, Handling concept 2, consisting of Lift table, Lhjdpex Ap Akefx Af Ser Section bridging by roller conveyor Vacuum arm for positioning material Pneumatically lowerable stop fences Push off device Dust extraction hood for protective boards Dust extraction channel at outfeed from below Transport belt 4050 x 2250mm 14-position tool changer Simultaneous push off and infeed Table Length: 3100mm Table Width: 2250mm Thickness: 100mm X/Y: 96m/min Z: 20m/min 3 Vacuum pumps with a total vacuum capacity 900/1080m3/h 4 Pneumatically lowerable stops 9Kw main spindle – liquid cooled Aggregate interface main spindle c-axis Flex 5 interface for c-axis Ait Jet integrated in extraction hood 12 vertical drilling spindles, including quick-change system Grooving saw swivelling 90 degrees Tool Change Assistance Device Tool length Control PowerTouch with power control hardware CE Weeke Quality Pack Energy Saving Mode

Condition: new, HOLZ-HER 7405 EVOLUTION CONNECT machining center -Exhibition machine- This offer is an equipment package. The following items and options are already included in the price: Lhjdpfx Aou Tid Hef Ser - Material support - Height-adjustable infeed roller conveyor - EVOLUTION diamond formatting cutter set - CAMPUS V8 EVOLUTION CAD/CAM software - Flat screen 21.5", 16:9 - Workpiece length measurement LASER - Milling unit 7830 - 7887 tool changer 6-position magazine pick-up - ECO vacuum system - Air conditioning unit for switch cabinet cooling - Tool changer 7874 - Angular gear 7869 - Adapter for Clamex milling cutters - Tool set - 4-axis CLAMEX - Tool holder HSK-F 63 - Drilling unit XL 7885, 19 spindles - Manual control unit - Tool set - EVOLUTION for XL drilling head 7885 - new exhibition machine -

Condition: good (used), Year of construction: 2019, CNC machine with fixed table and dual drive gantry, five axis interpolating electrospindle. Particularly suitable for SIPS panels, woodworking, plywood, MDF, plastics and thermo formed prodcuts. 6120mm x 1605mm Working field in X / Y axis 6850mm X axis stroke 1970mm Y axis stroke 1080mm Z axis stroke Max height / panel passge 700mm C axis rotation + / - 360 degrees 12kw electrospindle with programmable speeds from 500 - 22,000 rpm 12 Position automatic toolchanger Auxiliary 2 position toolchanger 250m3/hr vacuum pump 2 Field phenolic working table suitable for vacuum cups Hoist points to fix jigs [ series of threaded holes on table for mechanical fixing ] Set of 3 disappearing stops Ljdpevpv Nbofx Af Sjhr OSAI Series 10 CNC control including [ for example ] PC with Windows XP [ or higher ] Interactive programming Paramteric programming 3D interplolation Cutter radius compensation Extraction requirements 2200m3/hr Weight 5235kg Year - 2019 CE FULL ORIGINAL SPECIFICATION SHOWN IN IMAGES

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 3300x2100x2100 mm Ljdjv A Ha Djpfx Af Sehr Weight 1500 kg Total power requirement 17,5 kw

Condition: used, What are Presale Items at Second Owner? Presale items are machines that we sell in their current condition ("as-is"). We have purchased these machines based solely on photos and sell them with the information provided in the advertisement. Unfortunately, we do not have additional details, such as exact dimensions or machine specifications. Additionally, these machines are often not yet in stock and have not been inspected by us. These machines are offered at competitive prices, which means the prices are lower than usual, but the risk lies entirely with the buyer. Please carefully review the information in the advertisement before making a purchase. If you have any questions, feel free to contact us! - Machine available from: 2026-01-05 - Documentation available: No - CE certificate present: No Financial information Lodpfx Ajx Nigxjf Sohr VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, machine/vehicle number: 008257, X axis working area: 3760 mm Lsdpfxjx A Td Se Af Sshr Y axis working area: 1550 mm Main Electrospindle power: 12 KW Number of controlled axes: 3 axes Total number of drilling spindles: 10 Total number of tool changer positions: 12

Condition: good (used), Infotec 1008 Rotary CNC machine adjustable RPM, manual or auto, 3Ph Ljdpfox Ai T Nsx Af Sohr

Condition: new, - Edition Partnership - With our TF 100 2.0 "Partnership Edition" we offer CNC technology for the highest demands. And at a sensational price. Drilling, grooving, milling Unique in operation and in the "Partnership Edition" even more so in terms of features: The TF 100 2.0, specially developed for furniture and interior TF 100 2.0, specially developed for furniture and interior than 5 m² production area, it can perform drilling 5 levels of the workpiece, groove sawing work and also milling work. The machine impresses with its extremely high processing speed with maximum precision and ease of operation. The standard pre-equipment for angular gears, the optional the optional CLAMEX and lock case milling cutters can be can be retrofitted easily and at any time. The TF 100 2.0 "Partnership Edition" is completely manufactured in in our large factory in Rimini, the headquarters of Masterwood, and is 100% "Made in Italy". ----- Technical data ----- Max. workpiece length X: unlimited, max. workpiece length Y: 1,000 mm, max. tool thickness Z: 60 mm, Lhedpfxeu Tiwvj Af Sjr Vertical spindles X - direction: 5 pieces, Vertical spindles Y - direction: 5 pieces, Horizontal double drilling spindles X - direction: 2 + 2 pieces, Horizontal double drilling spindles Y - direction: 1 + 1 piece, Units: 16 drill head, Drilling spindle speed: 4,000 rpm, Distance between drilling spindles: 32 mm, Motor power: 1.7 kW, Grooving saw: X - direction, Saw blade Ø: 125 mm, Extraction connection Ø: 150 mm, Dimensions (LxWxH): 1,920 x 2,818 x 1,620 mm, Weight: 1,500 kg

Condition: used, Year of construction: 2001, functionality: fully functional, Machine Data • Gantry system with fixed table and moving portal for minimal footprint • Base, bridge, and bridge columns made from steel, welded in one piece, stress-relieved and machined • Main machine assemblies are ribbed welded constructions, optimized for the best stiffness-to-weight ratio, vibration damping, and high acceleration • Each machine design is verified and optimized via finite element analysis (FEA) to ensure maximum quality, performance, and safety • Easily accessible machine table for straightforward loading and unloading with forklift or overhead crane • Ground precision linear guides with high preload and additional cover bands for optimal chip removal on all axes • Brushless digital A/C servo motors and controllers on all axes • Dual-sided, synchronized drive on the X-axis (gantry drive) • Rack and pinion drive on X and Y axes • Precision ball screws with double pillow block support on the Z-axis • Precision planetary gearboxes with low backlash • Fully enclosed cable drag chains protect cable harnesses from chips and dust • High-quality shielded cable drag chain wiring ensures superior protection against faults and failures • X-axis working area: 1,540 mm • Y-axis working area: 1,540 mm • Z-axis clearance: 150 mm • Z-axis travel: 200 mm • Network connection via Ethernet • Remote maintenance via Internet FlexiCAM Control • DIN-ISO 66025 G-code compatible • Includes TCP/IP network interface • 256 MB RAM • Simple operation via handheld control unit with display Spindle with Manual Tool Change • Power consumption: 2.2 kW • 5,000–24,000 rpm, steplessly programmable • Cooling by integrated electric fan Extraction System for Manual Tool Change • Hose connection diameter: 80–90 mm Lhodox E Ttbopfx Af Sjr FlexiCAM Midrange Vacuum Table (Side Channel Blower) • T-slot profiles, individual ball valves, 6 zones • Side channel blower: 7.5 / 9 kW • Approx. 558 m³/h (50 Hz) or 654 m³/h (60 Hz) Safety Devices • CE-compliant to DIN EN 13849 • Includes EMC filter, emergency stop • Light barrier system controlled by machine controller

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 2300x1250x1750 mm Lsdpfxev Dmrvo Af Sshr weight 800 kg total power requirement 8,5 kw

Condition: used, Year of construction: 2000, - Year: 2000 - Documentation available: No - CE certificate present: No - Serial number: AL/5776 Ledpfx Aew Dzliof Sohr - Number of milling spindles [pcs.]: 2 - └ Milling spindle 1: - - Number of controlled axes [pcs.]: 3 - - Max. spindle speed [rpm]: 24000 - - Main motor power [kW]: 6.6 - └ Milling spindle 2: - - Number of controlled axes [pcs.]: 3 - - Max. spindle speed [rpm]: 18000 - - Main motor power [kW]: 7.5 - Type milling table: Beam table - Tool clamping system: ISO30 - Drilling unit present: Yes - └ Horizontal drill spindles [pcs.]: 6 - └ Vertical drilling spindles [pcs.]: 18 - Saw unit present: Yes - Tool changer positions [pcs.]: 10 - System/software: NUM 1040 - Safety feature: Bumper guard - Vacuum pump present: Yes - └ Number [pcs.]: 1 - └ Brand: becker - Working range X [mm]: 3600 - Working range Y [mm]: 1350 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, machine/vehicle number: 005796, X axis working area: 3700 mm Y axis working area: 1550 mm Lsdpfjhwi U Tex Af Sohr Main Electrospindle power: 9 KW Number of controlled axes: 3 axes Total number of drilling spindles: 10 Total number of tool changer positions: 8

Condition: used, Year of construction: 2002, functionality: fully functional, Machine Data • Gantry-type machine with fixed table and moving portal for minimal footprint • Base frame, bridge, and bridge uprights made from welded, stress-relieved, and machined steel in one piece • Main machine assemblies consist of ribbed welded constructions engineered for optimal stiffness-to-weight ratio, vibration damping, and high acceleration • Each machine design is verified and optimized using finite element analysis (FEA) to ensure maximum quality, performance, and safety • Easily accessible machine table for straightforward loading and unloading via forklift or overhead crane • Ground precision linear guides with high pre-load and additional cover tape for optimal chip removal on all axes • Brushless digital A/C servo motors and controllers on all axes • Dual-side synchronised drive on the X-axis (gantry drive) • Rack-and-pinion drive on the X and Y axes • Precision ball screw drives with dual-end bearing units on the Z axis • Precision planetary gearboxes with low backlash • Enclosed cable drag chains protect the drag chain cabling against chips and dust • High-quality shielded drag chain cables offer maximum protection against interference and failures • X-axis travel: 3,120 mm • Y-axis travel: 2,190 mm • Z-axis clearance: 200 mm • Z-axis stroke: 280 mm • Network connectivity via Ethernet • Remote service via Internet Panel-Based CNC Control System • Touchscreen display • Multifunction keyboard with integrated touchpad • Integrated industrial PC with Windows 7 Professional, hard drive, and Ethernet • Comprehensive remote maintenance functionalities • Includes hand-held unit with electronic handwheel • MCP with rotary switch for feed and spindle override • Mobile control cabinet Hand-held Operating Device • Fast, increment-precise positioning • Handwheel with magnetic detent • Coarse, medium, and fine positioning • 2-channel emergency stop • Protection class IP65 Milling Spindle • Max. spindle power: 4 kW • Max. speed: 30,000 rpm • ISO-25 tool taper • Max. tool diameter (shank): 12 mm • Air-cooled • Pneumatic tool taper clamping • Dry, clean, oil-free compressed air required on customer side (< 0.1 μm, < 7 bar) Automatic Tool Changer / Linear • Linear tool magazine mounted outside the working area • Basic configuration: 4 slots • Up to 20 slots ISO-25 Extraction Unit for Automatic Tool Change • Hose connection diameter: 110 mm • Automatic up/down function for tool change Tool Length Sensor • Automatic tool length measurement via M command • Hard metal contact plate • Measuring accuracy: 0.001 mm • Contact force: 1.5 N Tool Length Sensor • Automatic tool length measurement via M command • Hard metal contact plate • Sensor mounted outside the working area 2x Side Channel Blowers • Max. power consumption: 7.5 kW • Maximum airflow: 650 m³/h • Rated voltage: 400 V Ledpfjx E Tmbsx Af Sjhr • Rated current: 14 A • Pressure: 39,500 Pa

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 1900x1250x1750 mm Lsdpfov Dmrijx Af Sjhr weight 600 kg total power requirement 6,5 kw

Condition: used, Year of construction: 2014, Price: On request What are Presale Items at Second Owner? Presale items are machines that we sell in their current condition ("as-is"). We have purchased these machines based solely on photos and sell them with the information provided in the advertisement. Unfortunately, we do not have additional details, such as exact dimensions or machine specifications. Additionally, these machines are often not yet in stock and have not been inspected by us. These machines are offered at competitive prices, which means the prices are lower than usual, but the risk lies entirely with the buyer. Please carefully review the information in the advertisement before making a purchase. If you have any questions, feel free to contact us! - Machine available from: 2026-03-30 - Year: 2014 - Documentation available: No - CE certificate present: Yes - Serial number: AA1/017825 - Number of milling spindles [pcs.]: 1 - Type milling table: Beam table - Drilling unit present: Yes - Tool changer positions [pcs.]: 12 - CNC documentation available: USB stick - Table length [mm]: 5200 - Table width [mm]: 1550 - Z-axis working range [mm]: 160 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets Ljdpfx Afsx Hwhxe Sjhr

Condition: used, machine/vehicle number: 007564, X axis working area: 3700 mm Y axis working area: 1550 mm Working Table: Flat table Main Electrospindle power: 10 KW Number of controlled axes: 3 axes Total number of drilling spindles: 12 Lodpfeum H Ekex Af Sshr Total number of tool changer positions: 13

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 2200x1250x1750 mm Lhodpfjv Dmrcjx Af Ser total power requirement 6,5 kw weight 700 kg

Condition: used, Year of construction: 2006, Empty weight: 4.000 kg Price: On request What are Presale Items at Second Owner? Presale items are machines that we sell in their current condition ("as-is"). We have purchased these machines based solely on photos and sell them with the information provided in the advertisement. Unfortunately, we do not have additional details, such as exact dimensions or machine specifications. Additionally, these machines are often not yet in stock and have not been inspected by us. These machines are offered at competitive prices, which means the prices are lower than usual, but the risk lies entirely with the buyer. Please carefully review the information in the advertisement before making a purchase. If you have any questions, feel free to contact us! - Machine available from: 2026-05-25 - Year: 2006 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Number of milling spindles [pcs.]: 1 - └ Milling spindle 1: - - Number of controlled axes [pcs.]: 5 - - Min. spindle speed [rpm]: 600 - - Max. spindle speed [rpm]: 20000 - - Main motor power [kW]: 11 - - C-axis present: Yes - Type milling table: Beam table - Tool clamping system: HSK-F63 - Drilling unit present: Yes - └ Horizontal drill spindles [pcs.]: 6 - └ Vertical drilling spindles [pcs.]: 12 - Saw unit present: Yes - Tool changer positions [pcs.]: 16 - System/software: Xilog plus - Safety feature: Safety mat - Vacuum pump present: Yes - └ Main motor power [kW]: 5.5 - └ Capacity [m³/h]: 250 - CNC options: Offcut conveyor, Manual control - Table length [mm]: 3050 - Table width [mm]: 1240 - Z-axis working range [mm]: 200 - X-axis maximum stroke [mm]: 3500 - Y-axis maximum stroke [mm]: 1815 - Z-axis maximum stroke [mm]: 440 - Transport weight [kg]: 4000kg - Transport packages [pcs.]: 1 Ledex Hfikspfx Af Sshr Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, machine/vehicle number: 008238, X axis working area: 3660 mm Y axis working area: 1550 mm Working Table: Flat table Main Electrospindle power: 12 KW Number of controlled axes: 3 axes Lsdjx A E Tfjpfx Af Sehr Total number of drilling spindles: 12 Total number of tool changer positions: 15

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 2100x1250x1750 mm weight 700 kg Ledpfsv Dmq Sjx Af Sshr total power requirement 8,5 kw

Condition: used, Year of construction: 2014, operating hours: 11,517 h, Price: On request What are Presale Items at Second Owner? Presale items are machines that we sell in their current condition ("as-is"). We have purchased these machines based solely on photos and sell them with the information provided in the advertisement. Unfortunately, we do not have additional details, such as exact dimensions or machine specifications. Additionally, these machines are often not yet in stock and have not been inspected by us. These machines are offered at competitive prices, which means the prices are lower than usual, but the risk lies entirely with the buyer. Please carefully review the information in the advertisement before making a purchase. Lsdpfex E Uk Uox Af Sehr If you have any questions, feel free to contact us! - Year: 2014 - Documentation available: No - CE certificate present: No - Serial number: 070614/B/1-407 - Operating hours: 11517 - Number of milling spindles [pcs.]: 1 - └ Milling spindle 1: - - Number of controlled axes [pcs.]: 4 - - C-axis present: Yes - Working range X [mm]: 7220 - Working range Y [mm]: 1580 - Z-axis working range [mm]: 180 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 8800x2900x2100 mm Ledpfx Ajv A Hcrof Sehr Weight 6500 kg Total power requirement 18-36 kw

Condition: used, Year of construction: 2009, total height: 2,900 mm, Empty weight: 14.000 kg Price: On request Lhjdpjx Dil Ijfx Af Ssr What are Presale Items at Second Owner? Presale items are machines that we sell in their current condition ("as-is"). We have purchased these machines based solely on photos and sell them with the information provided in the advertisement. Unfortunately, we do not have additional details, such as exact dimensions or machine specifications. Additionally, these machines are often not yet in stock and have not been inspected by us. These machines are offered at competitive prices, which means the prices are lower than usual, but the risk lies entirely with the buyer. Please carefully review the information in the advertisement before making a purchase. If you have any questions, feel free to contact us! - Machine available from: 2026-03-31 - Details: - └ Description: Excluding tools - Year: 2009 - Documentation available: Yes - CE certificate present: No - Serial number: 113253 - Number of milling spindles [pcs.]: 1 - Material clamp system: Pneumatic - Drilling unit present: Yes - Tool changer positions [pcs.]: 24 - System/software: SIMATIC NET - Safety feature: Door interlock switches, Enclosed fence - CNC options: Unloading system, Loading system - CNC documentation available: USB stick - Table length [mm]: 4500 - Working range X [mm]: 4500 - Working range Y [mm]: 260 - Z-axis working range [mm]: 150 - Voltage [V]: 400 - Current consumption [A]: 63 - Fuse [A]: 80 - Power [kW]: 32.0 - Transport weight [kg]: 14000kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets