Eccentric Press - Single Column

WEINGARTEN ARP100

Condition: used, Single-column eccentric press WEINGARTEN type ARP 100 Machine no. No. 122481 Year of construction 1984 Pressure capacity 100 ton. throat 400 mm Table size 920 x 660 mm ram surface 700 x 450 mm Rear upright width 735 mm Stroke adjustment 20 - 160 mm Plunger adjustment 80 mm Installation height with 160 mm stroke max. 355 mm (without intermediate table top) Installation height with 20 mm stroke max. 425 mm (without intermediate table plate) Stroke rate 60 strokes/min. Table surface intermediate table top 920 x 610 mm Thickness of intermediate table top 90 mm Hole in intermediate table top Ø 210 / 180 mm Through-hole in machine table Ø 210 / 180 mm Table height above floor 800 mm (without intermediate table top) T-slot width in table and ram 22 mm Clamping pin bore 50 mm Bodpfx Acsu Rwa Isfjlp Motor power 11 kW Mains connection 400 Volt, 50 Hz - Hydraulic overload protection in ram - ORTLINGHAUS pneumatic clutch/brake combination - Electromotive ram adjustment with counter - Clamping pin bore with clamping piece - Front crankshaft support bearing - Gear reduction gears in closed oil bath gearbox - Two pneumatic tappet compensation cylinders - WOERNER automatic central grease lubrication - Lift release via electric foot switch or two-hand control panel - Electrical control cabinet permanently attached to the machine - Operating instructions and circuit diagram - UVV for manual insertion work Space requirement L x W x H 2200 x 1600 x 3250 mm Weight 8.3 tons Good condition

Condition: used, Year of construction: 1996, pressure 80 t throat 320 mm stroke 6 - 118 mm no. of strokes 30 - 80 Hub/min ram adjustment 70 mm table surface area 830 x 610 mm ram surface 650 x 400 mm column daylight (nach hinten) 630 mm total power requirement kW Blsdpfxetycdke Acfep weight of the machine ca. 8,1 t dimensions of the machine ca. B 1,2 x T 1,9 x H 3,3 m Furnishing: - with gear transmission - fixed table - automatic stroke adjustment - automatic ram adjustment - hydr. Overload - Ejector - Grease central lubrication - Cover plate for drainage hole - Continuous speed control using a frequency converter - Machine is technically checked in our company and receives a new control cabinet with safety controls and touchscreen - current UVV test with braking time measurement

Condition: used, Year of construction: 1979, Technical details: pressure: 250 t slide stroke: 40-160 mm throat: 545 mm ram adjustment: 110 mm Table dimensions: 1250x800x100 mm biggest distance between table & ram: 670 mm drawing capacity: 16 to table height over floor: 1000 mm surface area of ram: 900x670x100 mm distance between columns: 500x400 mm total power requirement: 23 kW weight of the machine ca.: 16,6 t Bjdeu Nfinepfx Acfslp dimensions of machine: 2,8x1,4x3,7 m dimensions electric cabinet LxWxH: 1,15x0,6x2,1 m Ejector and counter holder force: 16t Table size with 4x T-slots parallel running (1250x800x100mm) Ram plate with 4x T-slots radially running Data at bottom dead center UT: largest stroke: 510mm smallest stroke: 570mm Accessories: - Steel plate 1170x860x80mm *

Year of construction: 1990, condition: used, pressure 80 t throat 250 mm stroke 5/95 mm table surface area 805 x 510 mm distance table/ram Hub unten - 400 mm tool hole in ram 45 mm ram adjustment 100 mm ram surface 360 x 300 mm no. of strokes 55 Hub/min total power requirement 5,5 kW Bledpfx Acofn Aqnofop weight of the machine ca. 4 t dimensions of the machine ca. 0,83 x 1,7 x 2,6 m

Condition: good (used), Year of construction: 1977, functionality: fully functional, power: 15 kW (20.39 HP), pressing force: 200 t, table width: 800 mm, table length: 1,100 mm, throat depth: 440 mm, distance table to ram: 400 mm, total length: 37,200 mm, total width: 24,000 mm, total height: 18,200 mm, overall weight: 12,600 kg, ram adjustment: 110 mm, ram stroke: 40-180 mm incl. Helmerding feed, 400 mm x 4 mm Bedpfjtu Hvwex Acfjlp Strokes: 40 + 60 1/min Distance table/ram - adjustment top/stroke bottom: 400 mm Table opening: 450 mm diameter

Condition: refurbished (used), Year of construction: 2000, functionality: fully functional, Equipment: documentation/manual, TECHNICAL CHARACTERISTICS: Press Model: T160 CNR6 Serial number: 160/0/46/00 Year of construction: 2000 Nominal force: 1600 kN Weight: 13,800 kg Nominal number of strokes: 55 C/min. Min./max. number of strokes: 10/55 C/min. Max. number of insertions: 17 C/min. Min./max. clutch pressure: BAR 4.0÷5.5 Max. stop time: 0.22 s Safety distance: 355 mm. Energy (i=15% nominal strokes): 14,500 KJ Min./max. stroke: 10/200 mm Ram adjustment: 110 mm. PMI high adjustment: 430 mm Maximum extraction stroke: 60 mm Work surface dimensions (H, D, L): 78/750/1250 mm Ram dimensions (D, L): 600/850 Shank diameter: 60 mm Protrusion from the center: 370 mm Maximum mold size: 600/850 mm Bedpfxowaiw Ss Acfelp Maximum mold head weight: 344 daN Operating air pressure: BAR 5.5÷6 Stop position: TDC Voltage: V 380 Frequency: 50Hz Auxiliary voltage: V 24 NEW COMPONENTS INSTALLED: • Safety guards with safety keys; • Clutch plates; • Clutch pins and brite; • Flywheel bearings; • Flywheel oil seals; • Stroke change nose; • Balancing cylinder gasket kit; • Air pressure gauges; • Electrical panel; • Inverter (speed variator); • Motor; • Motor pulley; • Work surface revived on CNC machine Supplied with six (6) months warranty, technical documentation and CE conformity Twelve (12) months electrical panel warranty.

Year of construction: 1966, condition: used, pressure 100 t throat 410 mm stroke 8-112 mm no. of strokes doubel-strokes per min. 55 / 82 ram - range of adjustment 80 mm table surface area 950 x 700 mm ram surface 700x450 mm hole in the table Ø 280 mm table height 850 mm tool hole in ram Ø 50 mm Bjdpfxslp U D Eo Acfolp weight of the machine ca. 7,0 t dimensions of the machine ca. 1400x2200x2800 mm

Condition: excellent (used), Year of construction: 1988, functionality: fully functional, Equippment: 1 Grip feeder system right hand side 1 Eccentricpress 70 kN Bljdstmtzkspfx Acfsp 3 Narrow slide units 1 Control shaft Working range: wire diameter range: 0,5 - 3,0 mm strip metal width: max. 40 mm feeding length: max. 240 mm output: max 400/min

Year of construction: 1977, condition: used, pressure 100 t throat 410 mm stroke 8-112 mm no. of strokes 55/82 Hub/min ram - range of adjustment 80 mm table surface area 950x700 mm ram surface 700x450 mm hole in the table Ø 280 mm table height 800 mm total power requirement 11 kW weight of the machine ca. 7,5 t dimensions of the machine ca. BxTxH 1600x2200x3000 m Bjdpfx Aolp U Dajcfslp

Year of construction: 1970, condition: used, pressure 100 t throat 415 mm stroke 8-140 mm no. of strokes 48 Hub/min ram - range of adjustment 80 mm table surface area 920x670 mm ram surface 700x450 mm table height 800 mm Bedelp U Spspfx Acfslp tool hole in ram Ø 50 mm weight of the machine ca. 8 t dimensions of the machine ca. BxTxH 1500x2000x2800 mm