5984 Three rolls profile bending machine

VEB RV16

Condition: good (used), Technical specifications: Working width: 4050 mm Max. bending capacity: 6.0 mm Max. pre-bending: 4.0 mm Top roller diameter: 210 mm Side lower roller diameter: 210 mm Middle lower roller diameter: 210 mm Conical bending device by tilting the two side rollers Hydraulic folding bearings Pivoting control panel with digital display Dimensions (length x width x height): approx. 6900 x 2300 x 1800 mm Weight: approx. 14 tons Dodewkaalepfx Aa Iski The seller is not liable for typographical or data transmission errors. The machine's appearance, technology, and wear are consistent with its age; used machines are sold without any warranty.

Condition: good (used), turning length: 6,000 mm, spindle bore: 260 mm, Swing over bed Ø: 850mm Swing over cross slide Ø:500mm DBC Turning Length: 6000mm Spindle bore: 260mm Spindle power: 28kW Dkodpfx Aajwvtg As Iji Bed width: 650mm Stroke pinole: 300mm Spindle taper: 6Mk Workpiece weight: 5000 Length: 10000mm Width: 2100mm Height: 2600mm Weight: 12800kg

Condition: new, Year of construction: 2024, machine/vehicle number: 302340, Profile Bending machine KB Türkei model MB 30 bottom shaft 30 mm top shaft 35 mm two rollers driven with basement capacity: up to round tube 48 x 3,0 mm flat material 50x10 mm square tube 40x40x3,0 mm weight 170 kg Dkjdod S Uf Sepfx Aa Ioi motor 0,75 kw 400 Volt 50 Hz 3 ph.

Condition: excellent (used), Tacchi HD/1450 X 4M Large Spindle Bore (515mm) Year 2002 Siemens CNC Control Swing over bed 1450mm Swing over saddle 1000mm Hollow spindle 515mm Chucks front and rear of Headstock Speed range 1.5 – 450 rpm 15,000kg weight between centres Baruffaldi 4 way Auto Toolpost Dedexg Ivdspfx Aa Ioki 2 x 3 point steadies

Condition: new, functionality: fully functional, Year of construction: 2025, operating hours: 0 h, machine/vehicle number: plate roll, control type: CNC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: MG EVO, controller model: EVO 4 AXIS, number of rollers: 4, roller (bottom) diameter: 140 mm, roller (top) diameter: 160 mm, side roll diameter: 150 mm, roller diameter: 200 mm, roller length: 2,050 mm, working width: 2,000 mm, working height: 700 mm, sheet thickness (max.): 6 mm, sheet thickness steel (max.): 6 mm, sheet thickness stainless steel (max.): 6 mm, sheet thickness aluminum (max.): 6 mm, overall weight: 2,200 kg, total length: 3,200 mm, total width: 1,100 mm, total height: 1,200 mm, power: 4 kW (5.44 HP), input voltage: 400 V, number of digital displays: 4, warranty duration: 12 months, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, 4 ROLL BRAND MG ITALY, HYDRAULIC MODEL M2006P EVO_CNC PLATE BENDING ROLL PLANETARY DESIGN DOUBLE PINCH PRE-BENDING CNC_EVO PROGRAMMABLE AUTOCALCULATION AUTOMATIC PLATE ROLLING Capacity: -Width of plate: 2000 mm -Thickness of plate rolling 6 mm -Thickness of plate pre-bending 4 mm Rolls -useful width mm. 2050 -Top roll mm. 160 - Lower roll mm. 140 Configuration installed: • Surface hardening of the four rolls, smooth finishing suitable for stainless plates rolling • Dual pre-pinch, with adjustable force upon the input of plate thickness • Conical bending hydraulic attachment - hardened contrast pad. • Power driven rolls rotation top/bottom gearbox axial direct drive hydraulic each roll. • Calibration system for re-rolling of welded shells rounding. • Console electric independent with centralized commands joysticks and CNC screen readout. Djdpfew Dnd Sox Aa Ieki • CNC controller on touch screen 15” , CAD/CAM interface 4 axis auto calculation software package. with digital readout of the axis for use in manual rolling, semiautomatic and fully automatic programmable. • Opening front side hydraulic drop-end to unload closed shells. • Variable working speed step-less axis interpolation. • Safety installation with emergency stop. • Instruction manuals for operation and service.

Condition: like new (used), functionality: fully functional, Year of construction: 2016, operating hours: 10 h, Includes: Special iron turning tool ATRC 18 Special scroll bending tool ATAR 305 Spiral bending device ATSC Demonstration machine, no 10h worked! TECHNICAL DATA Shaft diameter mm. 30 Roller diameter mm. 128 Roller revolutions per minute rpm. 8.5 - 17 Drive motor Kw. 0.75 Main switch with release coil and built-in emergency (CP30 - CP30 R) - Reversing gear and double speed switch are mounted on a separate console (CP30 - CP30 R) - Foot switch Foot switch rotation control L/R with built-in emergency - (CP 30 PR) - Two-speed selector (CP 30 PR) - Mechanical regulation of the upper roller Mechanical regulation of the upper roller with position reading on display - Two traction rollers with ribbed surface Internal machine body made of steel - Steel shafts Dksdpfx Ajt Akxasa Isi steel shafts, hardened and ground - Gear wheels made of special special steel with ground teeth - Rollers made of special steel with a hardness of 59/60 HRC - Outer cover in ABS - Working position horizontal (CP 30) Horizontal working position (CP 30) - Horizontal and vertical working position vertical (CP 30 R - CP 30 PR) Weight: CP 30 PR 240 kg. External dimensions mm: CP30 PR Base 680 x 800 - Height 825 ACCESSORIES Straightening rollers with two positions - Universal rollers ( standard ) - Operating key Operating key - Operating instructions

Condition: ready for operation (used), total length: 3,620 mm, total width: 1,380 mm, total height: 1,250 mm, empty load weight: 5,000 kg, nominal power: 7.5 kW (10.20 HP), digitale uitlezing conische buiging Dodpsx Dd Htsfx Aa Ioki Number of rolls: 4 rolls - 2 roll driven Roll capacity cold: 2100 x 8/10 mm Roll dia upside: 190 mm Dia under roll - side rolls: 150 mm

Condition: excellent (used), Year of construction: 2001, turning length: 8,000 mm, turning diameter over bed slide: 2,000 mm, workpiece weight (max.): 25,000 kg, turning diameter over top slide: 1,550 mm, Swing over bed Ø: 2000mm Swing over cross slide Ø:1550mm DBC Turning Length: 8000mm Spindle bore: 150mm Spindle power: 95kW Bed width: 1400mm Tailstock spindle Ø: 260Ø Stroke pinole: 200mm Spindle taper: Metric 80Mk Workpiece weight: 25000 Power: 95A Speeds / ranges: 360Rpm Feed rate X-Axis: 0 - 6000mm/min. Feed rate Z-Axis: 0 - 6000mm/min. Length: 16000mm Width: 5000mm Height: 3800mm Weight: 80000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details! Dsdsxxxbzjpfx Aa Iski

Condition: like new (used), functionality: fully functional, Year of construction: 2024, control type: NC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: SIEMENS, controller model: PLC, number of rollers: 4, roller (bottom) diameter: 150 mm, roller (top) diameter: 150 mm, side roll diameter: 140 mm, roller diameter: 150 mm, roller length: 2,050 mm, working width: 2,000 mm, roller height adjustment: 18 mm, working height: 800 mm, sheet thickness (max.): 6 mm, sheet thickness steel (max.): 6 mm, sheet thickness stainless steel (max.): 4 mm, sheet thickness aluminum (max.): 6 mm, sheet thickness brass (max.): 6 mm, sheet thickness copper (max.): 6 mm, overall weight: 2,800 kg, total length: 3,800 mm, total width: 1,200 mm, total height: 1,100 mm, power: 3 kW (4.08 HP), input voltage: 400 V, input frequency: 50 Hz, number of digital displays: 4, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, 4 ROLL BENDING MACHINE NC HYDRAULIC MODEL 2000X6 MM / 4 MM PREBEND PROGRAMMABLE AUTOMATIC ROLLING NC 4 AXIS CONTROLLER Capacity: plate width 2000 mm thickness rolling 6 mm pre-bending 4 mm minimum diameter of rolling D= 180 mm depending on the plate thickness and strength Rollers length 2050 mm Upper roll size 150 mm Lower roll size 150 mm Rollers hardened surface high strength smooth surface finishing suitable for rolling stainless steel quality plates Conical plate rolling attachment Rotation electric powered on central rollers for bending traction of the plate Pre-pinch load variable upon plate thickness and strength Console electric commands push buttons with digital readout of the 4 rollers on the screen. NC programmable 4-axis to set automatic rolling with save 200 programs in memory front side hydraulic opening to remove the rolled shells Djdpsw Hpzwefx Aa Ijki speed slow/fast variable safety installation with emergency stop. Instruction manuals for operation and service. Layout mm 3800x1200xH1100 mm Weight 2800 Kgs

Condition: used, MAKE – TUSCAN MODEL – TL29 YEAR – 2002 CONTROL – FANUC OT TURRET – 8 POSITION WITH LOADS OF HOLDERS SWING OVER BED – 740 mm SWING OVER CROSS SLIDE – 420 mm CENTRE DISTANCE – 4000 mm SPINDLE BORE – 250 mm TRAVERSES – X-AXIS 500 mm/Z-AXIS 3700 mm SPEED – 15-700 RPM Dsdowmlcdepfx Aa Ioki MOTOR – 3 SPEED GEARBOX MOTOR 30KW SWARF CONVEYOR 4 JAW CHUCK SWARF CONVEYOR