Mandrel tube bending machine

Transfluid DB 648 K

Condition: new, Cesurbend Mandrel Bending Machine/Tube Bending Machine PBNC-65 A Technical Specifications Max. tube diameter (mild steel) 63 mm Max. wall thickness (mm) 3 Max. bending angle (°) 190 Tube bending speed (d/min) 7-10 Max. hydraulic pressure (bar) 200 Max. bending radius (mm) 250 Min. bending radius (mm) 45 Tube length (mm) 4000 Bending tolerances (mm) ±0.25 mm Bending motor power (kW) 7.5 Hydraulic motor power (kW) 4 Oil tank capacity (l) 50 Machine width (mm) 1500 Machine length (mm) 6200 Machine height (mm) 1500 Machine weight (kg) 2000 Features Crsdpexvzt Ujfx Aqtoh • The machine is equipped with 5 cylinders • On our standard NC machines, positioning and rotation after bending are achieved using the operator assistance and parallelism device. • You can bend faster and error-free by monitoring the progress and rotational positions of bends carried out with our machines equipped with an NC Car System.

Condition: new, maximum load weight: 23,800 kg, overall weight: 30,000 kg, axle configuration: 3 axles, Equipment: ABS, You can find our complete vehicle inventory with vehicles available for immediate and short-term delivery on our website. Excerpt from the equipment list. Complete equipment available upon request. Frame * Steel welded construction with front frame curve and rear bevel * Access ramp with excavator bucket recess in the center = recess in the rear between the longitudinal beams * Approximately 2,300 mm long Integrated into the outer frame * 5 pairs of approximately 4-tonne lashing points (4 x in the low bed and 1 x on the raised platform) * 7 pairs of recessed, pull-out approximately 10-tonne lashing rings (4 x in the low bed, 1 x in the access ramp, and 2 x on the raised platform) * Standard ball-bearing swivel frame attachments * Extendable widening elements on both sides of the low bed platform with softwood boards, approximately 50 mm thick * (The track width of the construction machinery to be transported must not exceed the outer frame width of approximately 2,550 mm) * 4 pairs of fold-up approximately 10-tonne lashing rings * Arrangement: 1 pair at the front on the raised platform, inside the longitudinal beams * 1 pair at the very back in the excavator bucket recess, left and right * 1 pair at the front on the raised platform, in front of the curve, inside the longitudinal beams * 1 pair in the low bed at the rear, in front of the access ramp, in the bucket recess on the left and right. Towing device * Fixed drawbar with pivoting drawbar eye, approximately 40 + 50 mm, curved design, silent block mounting, drawbar retaining spring with tensioner * Truck coupling height from approximately 840 mm to approximately 1,030 mm PP004059B Drawbar length approximately 1,800 mm Support system * 2 automatic folding supports at the rear Axles * SAF air suspension low loader axles with drum brakes, load capacity 11 t/axle, S-cam brake approximately 300/200 mm, automatic brake linkage adjuster Crodpjz Ed Auofx Aqtoh Wheels * 12 tires 235/75 R 17.5, 141J, manufacturer according to factory selection Braking system/Suspension * According to ECE regulation R13 * Dual-circuit compressed air braking system * Braking system manufacturer Wabco, EBS system 4S3M, 1st and 2nd axles monitored RSS/RSP * Stability program * Spring-loaded parking brake on 2nd and 3rd axles * Steel air tank * Brake/air connection lines with 2 single coupling heads, yellow/red EBS/ABS connection cable * Rubber band as a holder for EBS and electrical plugs * Air suspension with raising and lowering device (only on rear axles), automatic adjustment of the driving level from 15 km/h (RTR), with axle stop on the front axle Floor * Softwood floor, approximately 50 mm thick, impregnated, protruding approximately 5 - 10 mm above the frame Steel tear plate cover over wheels Ramps * 2 foldable, one-piece, lightweight steel access ramps * Length approximately 2,800 mm, width approximately 750 mm, with hardwood floor approximately 35 mm, impregnated * Ramps can be shifted in width from an intermediate distance of approximately 350 mm to a maximum overall width of approximately 3,000 mm * Ramps can be locked in the driving position by chains with tensioners * Ramp lifting aid with coil spring * Ramps can be shifted manually from the side with a rod * Square ribs welded on the outside on the ramps and rear access ramp Painting * Steel granulate cleaning * Hot-dip galvanizing * Multi-layer epoxy zinc phosphate primer and spray painting with 2-component polyurethane * Topcoat chassis = RAL 3002 carmine red *