Profile bending machine

Ercolina CE40H3

Condition: new, Year of construction: 2026, The CORMAK HBS275 band saw for cutting tubes, profiles and bars is widely used in all locksmith and metalworking workshops where precision, quality and cutting speed matter. The model is equipped with a 0-60° swivel arm; the saw guides are based on sintered carbide. The frame construction ensures accurate and quiet operation. Machine characteristics The horizontal metal band saw with swivel arm enables cutting in a plane perpendicular to the axis of the material being cut and at any angle within the range from 0 to 60°. The material to be cut can be fed manually or by any mechanical device, while the tool feed is automatic. The blade guides are equipped with special carbide plates and bearings. This has a major impact on blade guidance, service life, straightness, accuracy and cutting quality. Carbide guidance greatly reduces wear of the machine and blade. The machine is equipped with an efficient coolant pump with a closed coolant circuit. The saw arm is made of a single cast-iron casting and, together with the 27 mm wide cutting blade used in this saw, fully enables multi-series cutting of both profiles and solid materials. The vice is located in an adjustable bed and is equipped with a quick clamp. The blade guides are equipped with hard metal plates – sintered carbide and a rolling bearing system. It is precisely the SINTERED CARBIDE GUIDES that are responsible for the precision and straightness of the cut. The arm has been inclined at an angle of 25°, which increases blade durability and improves cutting conditions. A cleaning brush is mounted at the bottom of the arm to achieve excellent cleanliness and blade operation. The machine drive is transmitted via a worm gearbox. The machine has a three-phase motor with two cutting speeds and motor thermal protection. The shape of the upper part of the base forms a tray for draining coolant and collecting chips generated during material cutting. A cast-iron work table with a swivel arm and a control panel on a separate arm is mounted to the base. In the cutting process, the main cutting movement is the movement of the cutting blade, while the feed is the lowering of the arm. The arm lowering speed (cutting speed) is regulated by a hydraulic cylinder. The feed speed is adjusted on the saw control panel. Two cutting blade speeds are available: 37.5 and 75m/min. In the lower position of the arm (after cutting the material), the cutting blade drive is switched off automatically. Safety is ensured by cutting blade guards and micro-switches that stop the motor after the cutting cycle is completed or when any guard is opened; additional protection consists of automatic shutdown of the saw in the event of cutting blade breakage. The machine drive is transmitted by a motor with a worm gearbox. The motor with thermal fuse protects against overheating during operation. Technical data TOTAL POWER 1.5kW POWER SUPPLY 400V 50Hz ARM LOWERING ADJUSTMENT hydraulic cylinder BLADE LENGTH 2450 x 27 x 0.9 mm BLADE SPEED Hedpfx Ajudi Unoa Dot 37.5 / 75m/min VICE BASE HEIGHT 900 mm MACHINE DIMENSIONS (WITH ARM RAISED) (L x W x H) 1720 x 800 x 1800 mm WEIGHT 215 kg

Condition: new, Year of construction: 2024, 1050 mm 5.5 mm 5.0 mm roll diameter 130 / 195 mm 2.2 kW 1050 kg 2150 x 900 x 1200 mm - 2 central rollers driven by an electric motor Hedpfoq Sz Ahsx Aa Dot - Swing-out upper beam - Conical bending device - separate control panel - self-braking main motor - CE mark/Declaration of Conformity Special equipment included in the price: - hardened rollers - Motorized rear roller adjustment

Condition: good (used), Ring bending machine, profile bending machine, bending machine, pipe bending tool, pipe bender, pipe bending machine, mandrel bending machine -Manufacturer: Dako Gedore, electro-hydraulic pipe bender on a mobile base -Pipe diameter: 3/8" to 3" -Stroke: 320 mm -Motor: AEG 1.5 kW -Accessories: incl. bending jaws up to 2,5" (see photos) -Transport dimensions: 1140/1045/H1200 mm Total weight: 389 kg Hjdpfxjx Nfhrj Aa Dot

Condition: new, functionality: fully functional, Year of construction: 2025, laser power: 1,500 W, positioning speed: 80 m/min, repeat accuracy: 0.03 mm, input frequency: 50 Hz, warranty duration: 24 months, working range: 6,000 mm, Equipment: cooling unit, safety light barrier, G-12A Hedpfxeuc Sifj Aa Dst HIGH SPEED PROFESSIONAL TUBE LASER CUTTING MACHINE 1500-3000W The G series is equipped with many high-quality components with extreme performance and powerful cutting functions,suitable for tube cutting of various types and diameters ● The Highest Standards of Chucks in the Industry ● Two Methods for Fewer-tailing Cutting ● Variable Diameter Wheel Supporting ● Automatic Unloading Device ● Super Dust Removal System ● Patented Dust Baffle ● High-strength Cage Structure Welded Machine Bed Technical Parameter: Power: 1500W-3000W Maximum Tube Processing Size: 6000mm*φ120mm Max. Rotating Speed of Chucks: 160r/min X/Y-axis Positioning Accuracy≤0.05mm X/Y-axis Repositioning Accuracy≤±0.03mm Maximum positioning speed: 80m/min Max. Acceleration: 1.5G Round Tube Processing Dim: Φ10mm-Φ120mm Square Tube Processing Dim: 10mm*120mm Overall Dimensions: 9000mm*2700mm The Highest Standards of Chucks in the Industry The highest standards of chucks in the industry with strong clamping force, high rigidity, high speed, and stable performance Two Methods for Fewer-tailing Cutting Support two fewer-tailing cutting methods , choose one of them on the software interface according to different tube diameters Chuck double jaws: standard double jaws, small tube cutting precision is guaranteed Support: 2 sets of variable diameter wheel support standard (optional to increase to 3 sets)/optional servo support Unloading: [3M/4M] cylinder unloading rack/optional-[3M/4M] servo unloading rack/optional Loading: [Fully automatic loading rack/simple fully automatic loading rack/semi-automatic loading rack]/optional Dust removal: standard rear card hollow dust removal Short tail: chuck fixed, crossbeam fixed, short tail, front card open, rear card Continue to move forward, shorten the tail, ≥80 mm; if the short tail function is not used, the tail is about 200 mm Variable Diameter Wheel Supporting G Series has a wide range of cutting for various types and diameters of tubes, supported by the variable diameter wheel Automatic Unloading Device Efficient automatic unloading, saving time and labor costs, greatly improving production efficiency Super Dust Removal System The super dust removal system with ventilation design inside the chuck and the tube reduces the slag hanging in the tube, which is independently researched and developed by Glorystar Patented Dust Baffle Patented dust baffle protects important components from pollution and ensures stable performance High-strength Cage Structure Welded Machine Bed The industry’s highest-quality high strength cage structure welded machine bed with long life, anti-vibration, anti-torsion and anti-deformation

Condition: good (used), functionality: fully functional, Year of construction: 2007, machine/vehicle number: CA90H2 PIPE BENDING ROLL, shaft diameter: 90 mm, roller diameter: 260 mm, rotational speed (min.): 8 rpm, rotational speed (max.): 8 rpm, overall weight: 1,000 kg, total length: 1,260 mm, total width: 1,000 mm, total height: 1,260 mm, power: 3.68 kW (5.00 HP), input voltage: 380 V, type of input current: three-phase, operating speed: 8 mm/s, roll diameter: 260 mm, Equipment: documentation/manual, emergency stop, PROFILE BENDING ROLL SHAFTS OUTPUT 90 MM - PIPE BENDING ROLL MARGI CA90H2 YEAR 2007 SHATS OUTPUT SIZE 90 MM SET OF UNIVERSAL ROLLERS SIZE 260 MM LATERAL CORRECTOR ROLLERS LEFT/RIGHT SIDE SCREW ADJUST Hsdowkrr Tepfx Aa Det 4 SET OF ROLLERS FOR TUBE BENDING MM 61 - 78 – 90 – 116- CONSOLE ELECTRIC MOVABLE ON WHEELS ALL THE CONTROLS CENTRALIZED DIGITAL POSITION READOUT OF BENDING ROLLS UPPER ROLL DRIVEN MOTORIZED ELECTRIC POWERED WITH GEAR UNIT SIDE ROLLERS HYDRAULIC ADJUSTMENT POWERED INDEPENDENT WITH PISTON MACHINE REVERSIBLE CAN WORK WITH SHAFTS VERTICAL/HORIZONTAL. SAFETY AND EMERGENCY STOP EQUIPMENT INSTALLED WITH THE MACHINE MANUALS AND SCHEMATICS IN ORIGINAL ALONG WITH THE MACHINE WEIGHT 1000 KG DIMENSION 1260 X 1000 X H 1260 MM

Condition: new, Tubend hydraulic profile ring bending machine HPK 50 3 driven rollers Digital display Incl. standard roller set steel Hydraulic / motorized ring bending machine Can be used horizontally and vertically with 3 driven rollers 3 motor-driven rollers Hydraulic infeed of the top roller Hydraulic: 8 tons Rollers are hardened Left/right rotation via foot pedal Mounting: shaft 50 mm Hsdpfxeum R U Ao Aa Dst Roller Ø 162 mm Speed: 4.5 m/min Motor power: 1.1 kW Electrical connection 400 V According to CE standard Weight 510 kg L.W.H. 810 x 950 x 1500mm Power table see PDF file

Condition: excellent (used), functionality: fully functional, Year of construction: 2003, control type: manual, degree of automation: manual, actuation type: hydraulic, controller manufacturer: Tauring, controller model: digital readout, number of rollers: 3, shaft diameter: 70 mm, roller diameter: 245 mm, pipe diameter (max.): 100 mm, tube wall thickness (max.): 6 mm, overall weight: 1,300 kg, total length: 1,640 mm, total width: 1,220 mm, total height: 1,580 mm, power: 5.5 kW (7.48 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, Equipment: CE marking, documentation/manual, emergency stop, foot remote control, hardened rollers, Profile bending roll Tauring Alfa 70H2 year 2003 -Hydraulic section bending machine with digital readout -3 rolls powered driven - -dual pre-pinch pyramid roll configuration Shafts output 70 mm – Size of universal rollers 245 mm Lateral correctors left/right side hydraulic motorized operated Machine reversible can work with shafts vertical/horizontal Tooling: -Set of universal rolls and spacers Pipe bending rolls set for tube 22,5 – 61 – 76 - ( see photos of the rolls in enclosed ) Power total installed 5,5Kw Vac 380/50 Dimension 1640 x 1220 x H1580 mm Hjdoyx Dg Sepfx Aa Det Weight 1300 kgs -CAPACITY CHART IN ENCLOSED

Condition: used, functionality: fully functional, Year of construction: 2001, pipe diameter (max.): 60 mm, power: 1.85 kW (2.52 HP), I-Beam steel, flat 100 x 15 (Ø 500) mm I-Beam steel, upright 50 x 10 (Ø 500) mm Angle steel 50 x 6.0 (Ø 600) mm Round material 35.0 (Ø 500) mm Max. tube diameter 60 x 2.0 (Ø 1200) mm Square material 50 x 50 x 3 (Ø 1000) mm Bending speed 10.0 rpm Top roller diameter 165 mm Bore 40.0 mm Dimensions (L-W-H) 560 x 1430 x 980 mm Adjustment range: upper roller 124 mm Total power requirement 1.85 kW Weight 275 kg Low usage (!!) Manufacturer's list price incl. accessories approx. €12,500 Special price on request Equipment: - electro-hydraulic ring/profile bending machine - heavy and robust machine body - 2x powered rollers (MR2 series) - segmented roller dies - digital position display for top roller (0.1 mm) - manual upper roller adjustment - forward / reverse operation of bending rollers - Bending speed approx. 20% higher than comparable machines in its class Hsdpswvrazefx Aa Det - shafts made of forged & ground chrome-nickel steel - machine base frame - suitable for horizontal and vertical operation - mobile control panel - CE marking

Condition: used, Technical details: welding current - continuous: 320 / 100 A protection class: IP21 total power requirement: 17 kVA kVA weight of the machine approx.: 132 kg dimensions of machine: 1,3 x 0,5 x 0,9 m - TIG welding with direct current - TIG welding with pulsed current Hodpfsu Nwa Ssx Aa Det - E-hand welding Control switchover 2/4 cycle spot welding, stepless New components like: -hose package 4,0 meter, water cooled -ground tongs and ground cable 4,0 meter -pressure reducer -TIG welding torch ERGO 301 *

Condition: excellent (used), Year of construction: 2016, Cutting Capacity 0° round (tube): 300 mm Cutting Capacity 0° round (solid material): 180 mm Cutting Capacity 0° rectangular horizontal (hollow section): 320 x 290 mm Cutting Capacity 0° bundle (tube): 320 x 160 mm Cutting Capacity -45° round (tube): 300 mm Cutting Capacity -45° round (solid material): 110 mm Cutting Capacity -45° rectangular horizontal (hollow section): 300 x 280 mm Cutting Capacity -60° round (tube): 200 mm Cutting Capacity -60° round (solid material): 80 mm Hsdpexz Dqmsfx Aa Dst Cutting Capacity -60° rectangular horizontal (hollow section): 190 x 200 mm Cutting Capacity +45° round (tube): 270 mm Cutting Capacity +45° round (solid material): 110 mm Cutting Capacity +45° rectangular horizontal (hollow section): 270 x 200 mm Table height, material feed: 800 mm Main motor: 2.6 kW Cutting speed, stepless: 20 - 100 m/min Saw blade size: 3660 x 27 x 0.9 mm Machine dimensions (L x W x H): approx. 1800 x 950 x 1400 mm Net weight: 585 kg Accessories / Special features: • Semi-automatic swing-frame metal band saw • After the cutting cycle is started, the vice clamps automatically – after completion, it returns to its starting position • For mitre cuts from +60° to -45° with frequency inverter • Suitable for cutting stainless steel, tool steel, hollow profiles, and solid materials • Fully hydraulically controlled sawing functions • Saw drive with low-maintenance, oil-lubricated worm gear • Robust three-phase motor • Motor equipped with overload protection • Ball-bearing turntable • Saw arm inclined at 25°, resulting in longer saw blade service life • Saw arm swivels from +60° to -45° • Chip removal brush for optimal saw blade cleaning and maintenance • Frequency inverter: allows stepless adjustment of saw blade speed from 20 - 100 m/min • BRP – Saw band monitoring • Hydraulic vice with manual quick-release for lateral adjustment • Limit switches control upper and lower saw arm positions • No need to set the upper end point • Length stop with scale, left-side removal 3 m • Cut detector • Swivelling control panel • Micro-spray device • 2 x roller conveyors: 3 m discharge left, 6 m feed right • CE compliant Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel