Used other process engineering equipment for sale (77)

Condition: used, Year of construction: 2021, functionality: fully functional, Dürr Ecopure VAR 2206 Thermal Oxidizer with Flue Gas Cleaning (2021) For burning liquid and gaseous waste streams including fluorinated gases, e.g. PFAS, and recovery of aqueous hydrogen fluoride Emissions limits SO2 ≤ 100 mg/Nm³ NOX ≤ 30 mg/Nm³ Lhsdpfsz Ai Tpox Al Tol CO ≤ 50 mg/Nm³ CF4 ≤ 70 mg/Nm³ HF ≤ 1 mg/Nm³ NH3 ≤ 2 mg/Nm³ Comprising Direct fired thermal oxidizer Hot gas cooling and acid recovery Alkaline wet scrubber Honeycomb selective catalytic reduction deNOx system >1M cost spare parts Direct fired thermal oxidizer Including 2x natural gas combustion chambers and burners - High calorific liquid waste requires safe ignition supplemental hydrogen supply for acid formation - Gaseous waste streams injected via nozzles downstream and close to the burner - 1.5MW multi-fuel natural gas & liquid waste (minor fuel stream) burner with natural gas capacity up to 200Nm3/h - 1400C normal, 1540C max allowable temperature destruction of pollutants to reduce emissions with 3.28 MW thermal energy transfer - 2 seconds minimum residence time in combustion chamber at 1400C - 1,800mm combustion chamber internal dia. - Approx 300mm refractory lining - 2,400mm combustion chamber external dia. - 12,000mm combustion chamber internal length - 3.28MW maximum thermal capacity - 4,900Nm3/h, 60mbar, 14kW combustion air fans One chamber is active, the other one is on standby and can be prepared, repaired, or maintained. This allows minimizing shutdown and changeover time to only several days Wet scrubber hot gas cooling and acid recovery SGL Carbon Diabon HT-PQ 850 graphite pipe quencher - 6,000 Nm3/h capacity flow - 1,100 mm dia. - 2,000mm high - pumps SGL Carbon Diabon THX-RS falling film absorber shell & tube heat exchanger - 1,100mm dia. - 4,500mm tube length - 595 no. tubes - 22mm tube internal dia. - Graphite, carbon steel - pumps Quench vessel - PP/FRP - 1,100mm dia. - Approx. 6,000mm high 2x Scrubber absorber columns, each - Shell FRP/PP - Internals PP - 1,000mm dia. - 11,000mm high - Pumps - Dosing station FRP 5m3 Emergency water tank - 1,600mm dia. - 3,000mm high - 3kW heating 2x Teblick 100,000L HDPE hydrofluoric acid tanks (2019) Honeycomb selective catalytic reduction deNOx system - 5,900Nm3/h, 130mbar, 42kW induced draft fan - 320 kW gas/gas heat exchanger - 500 kW capacity reheat burner - 1.2m deNOx honeycomb catalyst Clean gas outflow Stack with flow & temperature measurement Spare parts include - 200 items of sensors, pumps, valves, gaskets, joints etc. - Graphite quencher - Falling film absorber With the redesign and maintenance support of Dürr, the system could also - be adapted to other halogenated gases with bricks to be selected according to gas application - cope with the presence of VOCs or contaminated air - larger volumes with the addition of a small lance for 15kg/h liquid injection

Condition: used, Used Gericke type N450x800 MK2 nibbler. Unit has mild steel body with stainless steel 4-blade rotor, screen frame & screen. Unit direct driven with motor/gearbox. Has approximate throughput capacity of 30,000 l/h (product dependent). Ljdpfxjzvybwe Al Tjhl

Condition: used, Large Industrial Plate Heat Exchanger – AISI 316 Stainless Steel Plates Heavy-duty industrial plate heat exchanger equipped with a large plate pack made of AISI 316 stainless steel. Product details: Equipment: Plate heat exchanger Plate material: AISI 316 stainless steel Large industrial plate pack Heavy-duty steel frame Flanged process connections Condition: Used industrial surplus Identification/marking: 316 Lodpfx Aez Di D Iel Tehl The heat exchanger is dismantled and available from stock in Rotterdam, The Netherlands. Manufacturer, exact model, capacity and other technical specifications are currently unknown. Please refer to the pictures for the configuration and condition. This equipment is industrial surplus and is sold as-is, without warranty or claims. Please contact us for additional information or to make an offer.

Year of construction: 2020, condition: used, Product: Sylysia 350, Gasil 23 D, Precarb 800, Calcilit, Benzophenone (partially lumpy), Lo-Vel 8100, Syloid 7000, bulk density: 0.08-0.73kg/l, particle size: powder, product temperature: 5-30°C, moisture: dry, consistency: free-flowing, non-sticky and non-agglomerated, system capacity: according to customer-provided container handling, operating mode: 3-shift operation, installation location: indoors/heated, ambient temperature: 5-30°C, power supply: 400V, 3Ph,N, 50Hz, control voltage: 24VDC, compressed air supply: 4-6bar, oil-free, max. surface temperature: 200°C, with documentation. An on-site inspection is possible, not connected to power. Lhedpjz D Hzqjfx Al Tjl

Condition: used, Used Cuccolini model VPM900 2/X stainless steel 3-deck screen. Screen measures approximately 900mm diameter. Unit has 0.73Kw, 1440rpm BOMEC vibrator motor. Weight: Estimated: Kg200.0 Dimensions: 1100mm X 1100mm Equipped With: Lsdjygvncjpfx Al Tshl Fitted with 300 micron & 500 micron ball tray screens. Can also include spare 710micron ball tray screen.

Year of construction: 2013, condition: used, Goudsmit rotary magnetic separator Ljdpexc Ew Dofx Al Tshl Article number: SCRZ2020018 Year of manufacture: 2013 Excludes rotor with magnetic bars (can be supplied by the manufacturer Goudsmit magnetic systems) Dimensions: 200mm x 200mm See our other ads VMA Wekerom

Condition: excellent (used), the plant is consisting of: - 2 chain separators - 2 55 cbm³ silos with discharge screws - 2 discharge screws - 4 mixing and homogenising chambers, - 5 conveyor belts - 2 double-shaft extruders connected in parallel Lodpfx Aslxzl Eol Tohl - 1 double shaft mixers - container for liquid extracts, etc.

Year of construction: 2012, condition: used, film width: 450 mm, roll width: 500 mm, machine/vehicle number: BA-18609, Equipment: CE marking, Coating Line Used for coating of battery electrodes Lhodpfx Ajzzpqrol Tsl - Roll width 500 mm - max. Web width 450 mm - max. Coating width 400 mm - Web speed 0.1-5 m/min - Various substrate films such as copper, aluminium, PET and PES - Doctor blade & slot die coating - Web guide system - Corona pre-treatment - integrated x-Ray areal weight measurement - 1x infrared oven - 2x convection oven Length coater: 14 m The buyer is responsible for the proper disassembly and pickup of the machinery.

Year of construction: 1989, condition: used, Used shredder Manufacturer: Seybert & Rahier Type: RST 413 Lhjdpfx Aleil Aquo Tjl Serial no.: 158282 Year of construction: 1989 Q: l/h 0-1000 H: mWS 33 Buffer liquid: 500 cm3

Condition: used, Lamella separator 2 pieces identical in construction: - Manufacturer and year of manufacture unknown (probably late 70s) - Rectangular design, with discharge screws to the funnel - Dimensions: Length 9700mm, width 3500mm, height 6100mm Lhsdpfx Aot Ay Scjl Tol

Year of construction: 1989, condition: used, Used shredder Manufacturer: Seybert & Rahier Type: RST 413 Serial no.: 158283 Year of construction: 1989 Q: l/h 0-1000 H: mWS 33 Ljdpfeil Aqqsx Al Tshl Buffer liquid: 500 cm3

Condition: used, Used cutter suction excavator Z-243 Operating hours: approx. 600 Application: self-maneuvering cutter suction dredger for cleaning water bodies, sludge removal from water bodies Pumping capacity: up to approx. 350 m3/h Suction dredger depth: approx. 5 m Total length with extension: 13,20 m Overall width: 2.90 m Overall height: 2.70 m Depth: 0.75 / 1.18 m Draught: ready for operation 0.62 m Suction pipe diameter: 150 mm Excavator depth at an angle: 45° for extension 5.0 m Fuel capacity: 300 liters Cutting speed (variable speed): 0-90 rpm and vice versa Cutting power: 10 kW / 13 hp Deutz main engine: 90 kW / 120 hp Transportable on the road: Yes Lhjdpfx Alorq I I Nj Tjl Largest part for transport: (main pontoon with extension) 11.60 x 2.50 x 2.50 m, approx. 10 tons Cabin: One-man operation in comfortable, low-noise cabin Transport: Can be dismantled and transported by road, overseas transport in containers Pontoons: The hull consists of several pontoons connected by a proven coupling system Coating: Marine coating system and cathodic protection for optimum protection Consumption: Low fuel consumption and low total cost of ownership System: Closed throat cooling system

Condition: good (used), Attachment: Lamella separator Condition: pre-owned m³/h up to 80 m Ljdpfxjb D Etko Al Tehl Usage: Separation of solids and liquids by sedimentation. Lamella separator as a preliminary stage before filter presses are often used for thickening. The filter press in relation to the filter surface can be sized smaller through a thin slurry before thickening. The plant is in good condition and available for rent and for sale. Visit us at the factory is like possible agreement.

Year of construction: 1992, condition: used, Plant used separation / separation system Manufacturer: Schauenburg Lodpfx Aob Swr Njl Tjhl Type: MAB 125 Engine type: 1130-1190 Year of construction: 1992 Power: 125 m ³/h Speed: 1000 rpm KW: 2.7

Condition: used, Used Crusher for Filter Cake / Lump Breaker Ledpfx Alsbpia De Tohl Drive: Lenze The crusher for filter cake or lump breaker consists of two horizontal rotating shafts.

Condition: used, Plant: lamella separator, lamella clarifier, lamella separator Lodpfoppyhtox Al Tohl Condition: used, up to 120 m³/h depending on medium Design: robust, powerful design Material: VA on conatin frame, 30 ' container, scraper plates: in PP dimensions: LXBXH 7580X2435X3000 mm Weight: approx. 8000 kg Principle: The dirty water is fed to the inlet of the lamella separator and flows downwards in it. Due to the arrangement of the lamella plates in the lamella separator, the dirty water is diverted below the lamellae and flows upwards through the lamellae. Thus, the solids sink to the bottom of the lamellas. The purified water is transported to the outlet. The solids on the lamellas gradually slide down along the lamella plates. This is where the sludge funnel is located. Scraper: Optionally, we offer the lamella separator with a scraper, which keeps the sludge flowable. Application: Separation of solids and liquids by sedimentation. Lamella separators are often used as a preliminary stage before filter presses or decanters for thickening. By pre-thickening a thin sludge, the filter press can be sized smaller in terms of filter area. The plant is in good condition and is available for rent or purchase. An inspection at our plant is possible by arrangement. We also offer new lamella separators with a delivery time of approx. 8 to 10 weeks !

Year of construction: 2011, condition: used, functionality: unexamined, US welding system with UPS 20L - Ultrasonic generator Martin Walter MW 2000 WMI - The previously installed printer is missing Lhodszlnb Ropfx Al Tjl - One or two air hoses are leaking - A test camera is missing - Shipping is possible for an additional charge.

Year of construction: 2021, condition: ready for operation (used), functionality: fully functional, FLOW & THERMAL Regenerative Thermal Oxidizer (RTO), 18,000 Nm³/h (2021) Complete industrial system for the treatment of process water containing Volatile Organic Compounds (VOCs), consisting of stripping columns and a three-chamber Regenerative Thermal Oxidizer. Manufactured by Flow & Thermal Solutions / TECAM in 2021, the equipment was installed at a PET production plant and remained operational until the factory closed on 27 November 2025. The system removes VOCs from the water by means of air stripping and subsequently destroys them in the RTO through high-temperature thermal oxidation. Heat recovery through ceramic media helps reduce natural gas consumption. Main features • Manufacturer: Flow & Thermal Solutions / TECAM • Year: 2021 • Serial number: F002 • RTO nominal capacity: 18,000 Nm³/h • Configuration: three-chamber regenerative RTO • Fuel: natural gas • Honeywell / Eclipse TJ 200 burner • Burner output: 58–586 kW • Electrical supply: 400 V, 50 Hz • Electrical power stated on the nameplate: 40 kW Ledpezvcknjfx Al Tjhl • 30 kW Soler & Palau ATEX main fan • Siemens PLC automation with HMI touchscreen • LEL monitoring, purge, dilution, bypass and pneumatic valve systems • Vertical stack: 10 m high, diameter: 800 mm • CE marked Performance and operation The equipment operated at actual flow rates close to its nominal capacity, with recorded values ranging from approximately 16,400 to 17,900 Nm³/h. The latest available emissions test, carried out by DEKRA in December 2023, recorded the following values: • TOC: 13 mgC/Nm³ • NOx: 3–4 mg/Nm³ • CO: 125–153 mg/Nm³ During the tests, the equipment operated at an approximate temperature of 775–780 °C, with a treated water flow rate of 3.5 m³/h. Stripping columns The system includes: • Original stripping column, designed for approximately 6 m³/h. • Second Tecnium SLFKK9 stripping column, manufactured in PPH, with a nominal capacity of 8 m³/h and a maximum capacity of 10 m³/h. The second column was installed, but it is currently dismantled and lying on the ground after being knocked down by strong winds during the winter. It has a hole in the base which, according to the available information, is considered potentially repairable. The Tecnium column is equipped with internal packing, distributors, a mist eliminator, connections, drainage and provisions for integration with the existing control system. Condition and maintenance The system remained operational until the final closure of the plant in November 2025. The latest preventive maintenance was carried out by TECAM in June 2025 and included mechanical and electrical inspection, burner, fans, stripping columns, instrumentation, valves and functional testing. The equipment was operational, although maintenance work is required before recommissioning, mainly involving: • Process valves • Internal insulation of the towers • Ductwork and seals • Main fan impeller and expansion joints • Repair of the base of the second stripping column TECAM technical documentation is available regarding the recommended works, and several spare parts are also available. Scope of supply The system includes: • Three-chamber RTO • Combustion chamber • Burner and gas train • Main fan • Two stripping columns • Dilution and purge system • Hot bypass • LEL analysers • Stack • Ductwork • Electrical cabinets and controls • Platforms, ladders and support structures • Available spare parts

Condition: excellent (used), flowmeter Endress-Hauser Pulsmag V + Variomag measuring range:0,0420 m3/sec Power 0 - 20 mA Lhsdpfefcb Nbsx Al Tol Temperature max. 80 °C lining material: HG Connections DN 150 /PN16 Voltage 220 V measuring range Frequency 50 Hz Length 220 mm Width 260 mm Height 350 mm Weight 13 kg

Condition: excellent (used), Flow meter Endress-Hauser promag 10w80 Temperature.-20 - + 80 ° C ps: 16 bar Materials PU Lhodpfxofcb Nno Al Tel DN 80 / PN16 connections Voltage 220 V. Min-max measuring range: 90 ... 3000 dm3 / min Frequency 50 H IP67 Length 248 mm Width 180 mm Height 200 mm

Condition: new, Zum Verkauf stehen 70 Stück Edelstahl Rückschlagventile. – Material: 1.4408 (AISI 316) – Nennweite: DN15 / 1/2" – Druckstufe: PN63 – Zustand: neu, unbenutzt (Lagerware) Die Ventile stammen aus industriellem Lagerbestand und wurden nie installiert. Geeignet für: – Chemische Industrie – Lebensmittelindustrie – Wasseraufbereitung – Prozessanlagen – Wartung und Ersatzteile Sehr interessanter Posten für Industrie und Handel. Verkauf einzeln oder als Komplettpaket möglich. Preis: 49 € pro Stück Mindestabnahme: 5 Stück Komplettpreis für 70 Stück: 2.800 € Standort: Slowakei (EU) Versand europaweit möglich For sale: 70 stainless steel check valves – Material: 1.4408 (AISI 316) – Size: DN15 / 1/2" – Pressure rating: PN63 – Condition: new, unused (warehouse stock) The valves originate from industrial stock and were never installed. Suitable for: – chemical industry – food processing – water treatment – process engineering – maintenance and spare parts Very attractive lot for industrial users or resellers. Available individually or as a complete lot. Price: 49 € per unit Minimum order: 5 units Full lot price (70 units): 2,800 € Lsdpeyxqq Dsfx Al Tehl Location: Slovakia (EU) Worldwide shipping possible

Year of construction: 2003, condition: good (used), functionality: fully functional, X-TEK RTR160UF: X-TEK Systems Ltd., England Model: RTR160UF Type: Ultra Focus X-Ray System Max. X-ray voltage: 160 kV Max. power: 60 W Focus size: 5 (Ultra Focus) Manipulator: 50 kg, 5 axes Power supply: 230 VAC, 50/60 Hz Lhjdpozl Scrofx Al Tjl Serial number: RTR/124 Model: RTR160UF X-ray source: 160 kV, 60 W, 5 m Ultra Focus Manipulator: 50 kg, 5-axis Serial No.: RTR/124 Supply: 230 VAC, 50/60 Hz Specified cabinet leakage: < 1.0 Sv/hr at any point on the cabinet surface under the stated test conditions. This is an industrial cabinet X-ray inspection system, designed for high-resolution non-destructive testing (NDT) of components, electronics, castings, solder joints, and similar items. The 5 m ultra-focus source is intended for very high-resolution imaging.

Condition: used, Two Ystral inline mixers are for sale. Ljdpoga D I Ujfx Al Tehl Mixer data: RPM: 1465 V: 230 / 400 kW: 11 Shaft length: 560 mm Overall length: 1220 mm Impeller diameter: 360 mm For more information, see the data sheet.

Year of construction: 1993, condition: used, Two-stage plate heat exchanger. First stage - Heating: hot water / product Product inlet approx 61-62°C, outlet approx 72°C, flow rate 600 hl/h; Hot water inlet approx 72,5°C, flow rate 750 hl/h Second stage - Regeneration: product / product Product inlet approx. 0-4°C, product outlet approx. 61-62°C, flow rate 600 hl/h; Product inlet approx. 72°C, product outlet approx. 11-14°C, flow rate 600 hl/h Additional title: 2-stage heat exchanger Capacity: 600 hl/h Hot water: 750 hl/h Operating pressure: 21 bar Lhsdpoztzckefx Al Tjl Operating temperature: 100 °C Length: 2,15 m Width: 0,95 m Height: 2,15 m Weight: 5000 kg Material: EPDM HT / NBR / 1.4439

Year of construction: 2006, condition: used, This plate heat exchanger from APV offers efficient and reliable heat transfer with a capacity of up to 240 hl/h in two stages. With a generous heat exchange area of 134 m² and a robust design for operating pressures up to 23 bar, this unit is well suited for demanding applications in breweries and the beverage industry. Thanks to its solid construction and compact design, it can be easily integrated into existing systems while ensuring high thermal performance and energy efficiency. An excellent and cost-effective solution for wort cooling, product heating, or other process applications. Our team at VBW Asset Trade will be happy to answer your questions. Ljdpfx Aloztzbys Tehl Capacity: 240 hl/h 2 stages Heat exchange area: 134 m² plate tracery min. 880 mm, max. 910 mm, actual 885 mm Operating pressure: 23 bar Length: 2000 mm Width: 700 mm Height: 2000 mm