Tube bender

Zopf BB 60

Condition: new, Year of construction: 2026, The CORMAK HBS275 band saw for cutting tubes, profiles and bars is widely used in all locksmith and metalworking workshops where precision, quality and cutting speed matter. The model is equipped with a 0-60° swivel arm; the saw guides are based on sintered carbide. The frame construction ensures accurate and quiet operation. Machine characteristics The horizontal metal band saw with swivel arm enables cutting in a plane perpendicular to the axis of the material being cut and at any angle within the range from 0 to 60°. The material to be cut can be fed manually or by any mechanical device, while the tool feed is automatic. The blade guides are equipped with special carbide plates and bearings. This has a major impact on blade guidance, service life, straightness, accuracy and cutting quality. Carbide guidance greatly reduces wear of the machine and blade. The machine is equipped with an efficient coolant pump with a closed coolant circuit. The saw arm is made of a single cast-iron casting and, together with the 27 mm wide cutting blade used in this saw, fully enables multi-series cutting of both profiles and solid materials. The vice is located in an adjustable bed and is equipped with a quick clamp. The blade guides are equipped with hard metal plates – sintered carbide and a rolling bearing system. It is precisely the SINTERED CARBIDE GUIDES that are responsible for the precision and straightness of the cut. The arm has been inclined at an angle of 25°, which increases blade durability and improves cutting conditions. A cleaning brush is mounted at the bottom of the arm to achieve excellent cleanliness and blade operation. The machine drive is transmitted via a worm gearbox. The machine has a three-phase motor with two cutting speeds and motor thermal protection. The shape of the upper part of the base forms a tray for draining coolant and collecting chips generated during material cutting. A cast-iron work table with a swivel arm and a control panel on a separate arm is mounted to the base. In the cutting process, the main cutting movement is the movement of the cutting blade, while the feed is the lowering of the arm. The arm lowering speed (cutting speed) is regulated by a hydraulic cylinder. The feed speed is adjusted on the saw control panel. Two cutting blade speeds are available: 37.5 and 75m/min. In the lower position of the arm (after cutting the material), the cutting blade drive is switched off automatically. Safety is ensured by cutting blade guards and micro-switches that stop the motor after the cutting cycle is completed or when any guard is opened; additional protection consists of automatic shutdown of the saw in the event of cutting blade breakage. The machine drive is transmitted by a motor with a worm gearbox. The motor with thermal fuse protects against overheating during operation. Technical data TOTAL POWER 1.5kW POWER SUPPLY 400V 50Hz ARM LOWERING ADJUSTMENT hydraulic cylinder BLADE LENGTH 2450 x 27 x 0.9 mm Nedpfx Apsudi Unohslg BLADE SPEED 37.5 / 75m/min VICE BASE HEIGHT 900 mm MACHINE DIMENSIONS (WITH ARM RAISED) (L x W x H) 1720 x 800 x 1800 mm WEIGHT 215 kg

Condition: excellent (used), functionality: fully functional, Year of construction: 2003, control type: manual, degree of automation: manual, actuation type: hydraulic, controller manufacturer: Tauring, controller model: digital readout, number of rollers: 3, shaft diameter: 70 mm, roller diameter: 245 mm, pipe diameter (max.): 100 mm, tube wall thickness (max.): 6 mm, overall weight: 1,300 kg, total length: 1,640 mm, total width: 1,220 mm, total height: 1,580 mm, power: 5.5 kW (7.48 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, Equipment: CE marking, documentation/manual, emergency stop, foot remote control, hardened rollers, Profile bending roll Tauring Alfa 70H2 year 2003 -Hydraulic section bending machine with digital readout -3 rolls powered driven - -dual pre-pinch pyramid roll configuration Shafts output 70 mm – Size of universal rollers 245 mm Lateral correctors left/right side hydraulic motorized operated Machine reversible can work with shafts vertical/horizontal Tooling: Nsdsyx Dg Sepfx Aphslg -Set of universal rolls and spacers Pipe bending rolls set for tube 22,5 – 61 – 76 - ( see photos of the rolls in enclosed ) Power total installed 5,5Kw Vac 380/50 Dimension 1640 x 1220 x H1580 mm Weight 1300 kgs -CAPACITY CHART IN ENCLOSED

Condition: new, Year of construction: 2026, Mandrel-free pipe bending machine RB 54 - NC-controlled, with large program memory Article number: 4300054 NC control for setting the bending angle Up to 50 programs can be saved High-quality, robust design Fast tool change Purely motor drive Automatically returns to the starting position TECHNICAL DATA General information Bending radius max. 162mm Bending angle max. 210° Bending speed(s) 2rpm Torque 2341Nm Dimensions and weights Length (product) approx. 600mm Width/depth (product) approx. 220mm Height (product) approx. 470mm Weight (net) approx. 107kg Bending performance Nsdpfx Ajvk Scgophjlg Bending performance of pipe material 420 N/mm² (Ø x wall thickness) 54 x 4mm Bending performance of pipe material 350 N/mm² (Ø x wall thickness) 54 x 4mm Bending performance of pipe material 650 N/mm² (Ø x wall thickness) 42 x 3mm Electrical data Drive motor power 1.1kW Connection voltage 400V Mains frequency 50Hz Location: from stock - available immediately -

Condition: good (used), functionality: fully functional, Year of construction: 2007, machine/vehicle number: CA90H2 PIPE BENDING ROLL, shaft diameter: 90 mm, roller diameter: 260 mm, rotational speed (min.): 8 rpm, rotational speed (max.): 8 rpm, overall weight: 1,000 kg, total length: 1,260 mm, total width: 1,000 mm, total height: 1,260 mm, power: 3.68 kW (5.00 HP), input voltage: 380 V, type of input current: three-phase, operating speed: 8 mm/s, roll diameter: 260 mm, Equipment: documentation/manual, emergency stop, PROFILE BENDING ROLL SHAFTS OUTPUT 90 MM - PIPE BENDING ROLL MARGI CA90H2 YEAR 2007 Nledpfjwkrr Tox Aphog SHATS OUTPUT SIZE 90 MM SET OF UNIVERSAL ROLLERS SIZE 260 MM LATERAL CORRECTOR ROLLERS LEFT/RIGHT SIDE SCREW ADJUST 4 SET OF ROLLERS FOR TUBE BENDING MM 61 - 78 – 90 – 116- CONSOLE ELECTRIC MOVABLE ON WHEELS ALL THE CONTROLS CENTRALIZED DIGITAL POSITION READOUT OF BENDING ROLLS UPPER ROLL DRIVEN MOTORIZED ELECTRIC POWERED WITH GEAR UNIT SIDE ROLLERS HYDRAULIC ADJUSTMENT POWERED INDEPENDENT WITH PISTON MACHINE REVERSIBLE CAN WORK WITH SHAFTS VERTICAL/HORIZONTAL. SAFETY AND EMERGENCY STOP EQUIPMENT INSTALLED WITH THE MACHINE MANUALS AND SCHEMATICS IN ORIGINAL ALONG WITH THE MACHINE WEIGHT 1000 KG DIMENSION 1260 X 1000 X H 1260 MM

Condition: good (used), Year of construction: 2018, machine/vehicle number: 431-92, Offer 26142 Technical data: - Cutting range at 90°: round 350 mm - Cutting range at 90°: flat 320 x 460 mm - Miter angle adjustable from 90° to 30° - Cutting range at 45°: round 280 mm - Cutting range at 45°: flat 350 x 280 mm - Cutting range at 45°: round 180 mm - Material feed system Njdpfezc Izasx Apholg - Material support height approx. 740 mm - Saw band dimensions 4350 x 34 x 1.1 mm - Cutting speed adjustable from 25 to 90 m/min - Hydraulic lifting and lowering of the saw frame - Cutting pressure continuously adjustable - Material clamping device - 3 roller conveyors, total length 1400 mm - 1 roller stand - Total motor power 400 V / 4.8 kW - Space requirement approx. W 1400 x H 1400 x D 2200 mm - Weight approx. 1900 kg

Condition: new, neu ca. 4 Wochen ab Auftragse Italien 3620 € 38 mm 245 mm 300 mm 320 mm 23 kg 19 cm³ 38 x 1,5 mm 38 x 1,5 mm 35 x 3 mm 30 x 2 mm 35 x 1,5 mm 42 x 1,5 mm 42 x 1,5 mm 50 x 2 mm 50 x 2 mm 50 x 4 mm 20 mm 10 x 25 mm 25 x 20 (stehend), 25 x 1 mm 180 mm 36 mm 10 mm Nsdjwiqxiopfx Apholg 2,8 U/min 0.9 kW digital adjustment of the bending angle from 0 - 180 ° single phase motor 220V / 900W electric engine brake indicator light for indicating overload basement made of cast iron, suitable for mounting a tripod (tripod not included) 90° bend in 6 seconds foot pedal without tools OPTIONAL EQUIPMENT: tripod € 345,-

Condition: excellent (used), Year of construction: 2016, Cutting Capacity 0° round (tube): 300 mm Cutting Capacity 0° round (solid material): 180 mm Cutting Capacity 0° rectangular horizontal (hollow section): 320 x 290 mm Cutting Capacity 0° bundle (tube): 320 x 160 mm Cutting Capacity -45° round (tube): 300 mm Cutting Capacity -45° round (solid material): 110 mm Cutting Capacity -45° rectangular horizontal (hollow section): 300 x 280 mm Cutting Capacity -60° round (tube): 200 mm Cutting Capacity -60° round (solid material): 80 mm Cutting Capacity -60° rectangular horizontal (hollow section): 190 x 200 mm Cutting Capacity +45° round (tube): 270 mm Cutting Capacity +45° round (solid material): 110 mm Cutting Capacity +45° rectangular horizontal (hollow section): 270 x 200 mm Table height, material feed: 800 mm Main motor: 2.6 kW Cutting speed, stepless: 20 - 100 m/min Saw blade size: 3660 x 27 x 0.9 mm Machine dimensions (L x W x H): approx. 1800 x 950 x 1400 mm Net weight: 585 kg Accessories / Special features: • Semi-automatic swing-frame metal band saw • After the cutting cycle is started, the vice clamps automatically – after completion, it returns to its starting position • For mitre cuts from +60° to -45° with frequency inverter • Suitable for cutting stainless steel, tool steel, hollow profiles, and solid materials • Fully hydraulically controlled sawing functions • Saw drive with low-maintenance, oil-lubricated worm gear • Robust three-phase motor • Motor equipped with overload protection • Ball-bearing turntable • Saw arm inclined at 25°, resulting in longer saw blade service life • Saw arm swivels from +60° to -45° • Chip removal brush for optimal saw blade cleaning and maintenance • Frequency inverter: allows stepless adjustment of saw blade speed from 20 - 100 m/min • BRP – Saw band monitoring • Hydraulic vice with manual quick-release for lateral adjustment • Limit switches control upper and lower saw arm positions • No need to set the upper end point • Length stop with scale, left-side removal 3 m • Cut detector • Swivelling control panel • Micro-spray device • 2 x roller conveyors: 3 m discharge left, 6 m feed right • CE compliant Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 Njdpfx Aexz Dqmophelg DE - 44143 Dortmund - Wambel

Condition: good (used), Year of construction: 1977, machine/vehicle number: 22247, Offered 23250 Technical data: - Bending performance - Pipe at 45 kg / mm² Ø 6 - 48 mm - Max. bending angle 180 ° - Max. bending radius 145 mm - Drive 400 V / 1.7 kW - Space requirement approx. W 900 x H 1100 x D 1400 mm Nledjv Hzr Nopfx Aphsg - Weight approx. 600 kg - with - Pipe circular saw - Inside and outside pipe deburring device - Pipe necking device - Without tools

Condition: used, Year of construction: 1996, 4.0 mm 3.0 mm 30 - 120 Grad blade length 150 x 150 mm work height max. 900 mm table: 1000 x 650 mm engine output 3.0 kW weight 850 kg range L-W-H 1250 x 1000 x 1160 mm Furnishing: - Notching machine with angle adjustment 30° - 120° - Simple and functional "Touch Pad" control panel * Set-up stroke * Single stroke * continuous stroke - Plexiglas protection for better transparency - hardened knives also for cutting stainless steel - planed table surface * to avoid 'tilting' or 'slipping' of the metal sheet - adjustable lift height adjustment - Waste bin - free-moving footswitch - Operation manual BOSCHERT angle adjustment: - the one-piece 30° upper knife is within one Njdpfx Asxabpdspholg tool both with a left and directly connected to a right lower knife - once for each notch over 30° left and once on the right. - the swivel adjustment becomes pneumatic, immediately after completion of the first notch, lightning fast carried out.

Condition: used, Year of construction: 1982, Technical details: cutting diameter: 120 mm dimensions of saw-blade: 425 x 30 mm Nodpsu Nilaofx Apholg cutting range 90 degrees: round: 120 mm height over floor: 800 mm electrical connection: 380 V / Hz. strokes per minute: 60 / 92 / 140 Hübe/min. total power requirement: 1,5 kW Overall size: ca. L:1,2 x B: 0,75 x H: 1,10 (Bügel angehoben) m Vice adjustable in longitudinal direction by loosening the nuts. Mitre cut and straight cut: 45° and 90° with cutting pressure and lifting hydraulics After the cut is completed, the machine switches off and the saw blade remains in the lowest position. Workpiece holder via fixed jaw and clamping jaw, with hand crank Coolant device in the base limit stop *