Used Belflex Bf812 Sc M for sale (72,922)

Condition: used, Pay-off and take-up decoiler for coil material WANZKE CAMU Type SC 515/M Serial no. 8487 Year of manufacture: 2006 Coil weight approx. 1,500 kg Maximum coil width: 600 mm Coil inner diameter: 370 - 640 mm Maximum coil outer diameter: 1,800 mm Mandrel shaft diameter: 90 mm Lsdpfswvv Rqjx Al Tehl Distance from mandrel crown center to mandrel base: 950 mm Mandrel crown speed: 13 rpm Motor speed: 920 rpm Gearbox transmission ratio: 1:70 Mandrel drive motor power: 1.1 kW Power supply: 400 Volt, 50 Hz - Mechanical expansion of the mandrel crown with hand crank - Drive via geared motor with worm gearbox, directly mounted on the mandrel shaft - Geared motor with electric brake - Mandrel shaft with mechanical slip clutch, pre-tensioned and adjustable via disc springs - Mandrel crown without strip travel arms - Without electrical control system and without loop switch Space requirement (L x W x H): 1300 x 800 x 1230 mm Weight: 380 kg Good condition

Condition: new, functionality: fully functional, Manual equipment to cut the corners of the box blanks and make V & U-shape grooves. Ideal for mock-up samples and short runs. Corner sizes: max. 150 x 150 mm Cardboard sizes: max. 700 x 700 mm (box) max. 1000 x 700mm (cardboard cover) Lhjdew Ad N Ujpfx Al Tel Cardboard thickness: min. 1 mm – max. 4 mm Tools: Nr.1 for “V” shape groove from 80° to 100° Nr.1 for “V” shape groove from 100° to 130° Nr.1 for “U” shape groove from 6 mm to 8 mm (optional) Wheelbase: no limit

Condition: used, Year of construction: 2009, Roll production line WP Multimatic MUS Rollmeister SC 51 Year of manufacture: 2009 Suitable for sliced rolls, round rolls, and long rolls Maximum hourly output: approx. 5,100 pieces Weight range (without proofing): 30-90g Weight range (sliced rolls): 40-65g Pre-proofing cabinet I (before long rolling): 6 minutes Pre-proofing cabinet II (after long rolling, before cutting): 6 minutes Dough divider and rounding machine Multimatic MUS, 4-row Pressure roller on spreading belts after the head machine Long rounding station Pressure roller before the cutting station, height-adjustable Cutting station Bypass for green operation without proofing cabinet Discharge device for Euro pallet sizes With heating and humidification Lhsdjz A Sd Iopfx Al Tol With tunnel dryer

Condition: used, functionality: fully functional, Year of construction: 2003, operating hours: 45,500 h, punching force: 30 t, punching diameter: 89 mm, sheet thickness (max.): 5 mm, sheet thickness steel (max.): 4 mm, sheet thickness aluminum (max.): 5 mm, overall weight: 22,000 kg, total length: 17,000 mm, total width: 7,000 mm, total height: 3,500 mm, travel distance X-axis: 2,584 mm, travel distance Y-axis: 1,560 mm, workpiece weight (max.): 200 kg, compressed air connection: 6 bar, space requirement height: 3,500 mm, space requirement length: 17,000 mm, space requirement width: 7,000 mm, travel speed (max.): 10,800 mm/min, Equipment: safety light barrier, Finn Power punching machine 3000 x 1500 with an angle shear of 800 x 1500 mm and a stacker for 4 pallets. Loading table for sheets of 3000 x 1500. Punching up to 8 mm thickness, angle shear up to 5 mm thickness. Turret with 20 stations, including 1 multi-tool 10-16 and 1 multi-tool 24-8, 2 * Di, 3 * Ci, 2 * Bi. Lodpfx Alozdc Iqs Tshl Also has 2 forming stations, Bf and Cf. Always used for thin sheet metal, max. 2 mm. A tapping head TU6 is included, but it displays an error message. Must be sold urgently due to a lack of space.

Condition: used, Year of construction: 2011, Overview This M+F KEG-Technik MICROMAT M 1/1-F KeyKeg is a semi-automatic filling machine for one-way KeyKegs, built in 2011 by M+F KEG-Technik (Bottrop, Germany) and used in a Belgian brewery. The machine fills 20 l and 30 l KeyKegs at 50-60 kegs per hour. It became redundant when the brewery switched its production from one-way KeyKegs back to returnable stainless steel kegs. It has already been dismantled, is in storage and can be inspected on request. Technical data Ledpezrihxjfx Al Tjhl - Manufacturer: M+F KEG-Technik - Model: MICROMAT M 1/1-F KeyKeg - Year of manufacture: 2011 - Machine type: semi-automatic KeyKEG filling machine - Capacity: 50-60 KeyKegs per hour - Container formats: 20 l and 30 l KeyKEG - Fitting type: KeyKEG fitting - Connection voltage: 230/400 V, 50 Hz Equipment - EC Declaration of Conformity (Machinery Directive 2006/42/EC) - Technical documentation Condition Used. The machine has already been dismantled and is stored. Availability Immediately available. Location: Belgium. Handling and truck loading are included.

Condition: excellent (used), Year of construction: 2016, operating hours: 4,742 h, "RSA High-Performance Sawing, Deburring, Cleaning, and Drying Center" for Steel Tubes The processing center consists of: 1) RSA Precision High-Speed Saw RASACUT SC 3000 with bundle loader 2) RSA transfer system between the RSA Precision High-Speed Saw RASACUT and the RSA Deburring System RASAPLAN XY 3000 3) RSA Deburring System RASAPLAN XY 3000 4) Extraction system/wet separator for the RSA Deburring System RASAPLAN XY 3000 5) RSA Cleaning System RASACLEAN ET 3000 6) RSA Drying System TURBODRY Bundle loader extended for tubes up to 6,200 mm TECHNICAL DATA Tube diameter: 6 mm to 55 mm Wall thickness: 1 - 6 mm Bar weight: max. 10 kg/m Material: steel Magnetism: max. 3 Gauss Output length: 6,200 mm Sawable lengths: 150 - 3,000 mm Restriction: Ø 6 – 7.9 mm max. length: 1,200 mm Ø 8 – 9.9 mm max. length: 1,500 mm Ø 10 – 12 mm max. length: 2,000 mm Length tolerance: Ø 6 - 49 mm +/- 0.2; Ø 50 - 55 mm +/- 0.25 SAW BLADE DATA Saw blade diameter: max. 315 mm Bore: 40 mm Auxiliary holes: 4 x 12 mm Pitch circle: 64 mm Ledpfx Alsy E Iype Tshl NEW PRICE: €390,000

Condition: good (used), Year of construction: 2000, functionality: fully functional, travel distance X-axis: 1,000 mm, travel distance Y-axis: 350 mm, travel distance Z-axis: 480 mm, rotational speed (max.): 6,000 rpm, spindle speed (max.): 3,500 rpm, type of input current: AC, Equipment: rotational speed infinitely variable, AXA VSC 1-1000 M/K – Vertical CNC Machining Center Technical Data Feature | Specification Manufacturer | AXA Entwicklungs- und Maschinenbau GmbH Model | VSC 1-1000 M/K Year of Manufacture | 1991 Machine Type | Vertical Traveling Column Machining Center Control | Siemens 810 M/GA3 Axes | 3 axes, prepared for 4th axis Tool Changer | Automatic Tool Interface | SK 40 DIN 69871 A / 69872 A Tool Magazine | 22-position chain magazine Travel X | 1,000 mm Travel Y | 350 mm Travel Z | 480 mm Table Size | 2,350 × 500 mm T-Slots | 3 × 14 H9 Table Load | 500 kg per 1,000 mm Working Area Height | 230 – 710 mm Distance Spindle Center – Column | 425 mm Spindle Speed | 30 – 3,000 min⁻¹ Spindle Power | 11 kW (100% ED) / 14 kW (60% ED) Torque | 150 Nm (100% ED) / 180 Nm (60% ED) Rapid Traverse X/Y | 15 m/min Rapid Traverse Z | 10 m/min Feed Rate Range | 1 – 999 mm/min Repeatability | ± 0.0075 mm Positioning Accuracy | ± 0.015 mm Lodpfxjxp Hmaj Al Tshl Measuring Systems | Direct linear measuring systems in all axes Axis Drives | Siemens AC servo motors Ball Screws | In all axes Coolant System | 100 l tank, 40 l/min at 2 bar Chip Conveyor | Hinged belt conveyor, discharge height approx. 1,200 mm Central Lubrication | Automatic Optional Axis | NC rotary table RTA 200, Ø 300 mm Equipment Siemens 810 M/GA3 CNC control 9" monitor with softkeys 48 tool offset pairs Drilling and milling cycles Subprogram technique Teach-in and playback function Programming possible during running machining Full enclosure with splash guard Automatic spindle orientation Operating hour counter Complete machine documentation available

Year of construction: 2004, condition: used, functionality: fully functional, maximum load weight: 125 kg, loading space volume: 2.5 m³, machine/vehicle number: 3881 and 3690, Lot of 2 – TUPESA SC 125 V Industrial Steam Tumble Dryers (2004) Two High-Capacity Steam-Heated Tilting Drum Dryers An excellent opportunity to acquire two heavy-duty TUPESA SC 125 V industrial steam tumble dryers manufactured by TUPESA Maquinaria Textil, Spain. These industrial dryers are designed for continuous, high-capacity textile and garment drying, making them ideal for denim manufacturing, garment finishing, industrial laundries, and textile processing plants. Both units were previously installed in the MASI Jeans factory and formed part of a professional industrial laundry and finishing line. The machines are sold together as one lot. Unit K550 is operational. Unit K551 requires radiator replacement Technical Specifications • Manufacturer: TUPESA Maquinaria Textil • Model: SC 125 V • Machine Type: Industrial Steam-Heated Tilting Drum Tumble Dryer • Quantity: 2 Machines • Year of Manufacture: 2004 • Manufacturing Date: 17.12.2004 • Country of Manufacture: Spain • Power Supply: 380 V, 3-Phase, 50 Hz • Heating System: External Steam Supply • Variable Speed Drive: Danfoss VLT 2800 Inverter • Drum Type: Hydraulic Tilting Drum Machine Details Unit K550 • Internal Reference: K550 • Serial Number: 3881 • Operational Unit K551 • Internal Reference: K551 • Serial Number: 3690 • Requires inspection / suitable for spare parts or refurbishment Key Features • Two industrial steam-heated tumble dryers • Large-capacity tilting drum design • Hydraulic drum tilting for ergonomic loading and unloading • Steam-heated drying system • Danfoss variable-speed inverter drive • Industrial electrical control panel • Heavy-duty construction for continuous production • Designed for large-scale laundry and garment processing Includes • 2 × TUPESA SC 125 V tumble dryers • Danfoss inverter drives • Electrical control cabinets • Main drive motors • Steam connection valves • Exhaust fan assemblies • Industrial support frames Applications • Industrial laundry operations • Garment manufacturing • Denim production • Textile processing • Garment finishing • Commercial drying facilities • Heavy textile processing Condition • Sold as one lot consisting of two machines • One machine fully operational • Second machine requires approx.. 1000 euro radiator replacement. • Previously used in professional industrial production • Both machines are externally complete • Good overall industrial condition • Normal cosmetic wear consistent with factory use • Available for inspection before dismantling Location Valga, Estonia Dismantling & Transport Buyer is responsible for dismantling, loading, transportation, and all related costs. Lhsdjzkv R Dspfx Al Tsl Professional dismantling and lifting equipment are recommended due to the size and weight of the machines. Sales Terms Sold as-is, where-is, without warranty. Part of the MASI JEANS factory liquidation. The machines are available as this two-machine package or together with the complete industrial laundry and finishing line.

Condition: used, Year of construction: 2013, Overview Lodpsyq Ia Ejfx Al Tshl This KeyKeg filling machine, MICROMAT M1/1‑F KeyKeg, was manufactured in 2013 by Germany m+f KEG Technik. The machine is designed for filling KeyKegs and was used in a brewery. The equipment is no longer required by the seller and can be visited at any time on request. Technical data  - Formats: KeyKeg - Application: KEG filling - Operating pressure: 5.5 bar - Electrical supply: 230/400 VAC - Control voltage: 24 VDC - Frequency: 50 Hz  

Condition: excellent (used), Year of construction: 2011, operating hours: 5,303 h, functionality: fully functional, machine/vehicle number: 5847, travel distance X-axis: 600 mm, travel distance Y-axis: 580 mm, travel distance Z-axis: 360 mm, feed rate X-axis: 30 m/min, feed rate Y-axis: 30 m/min, feed rate Z-axis: 30 m/min, spindle speed (max.): 42,000 rpm, spindle speed (min.): 5 rpm, rapid traverse X-axis: 30,000 m/min, rapid traverse Y-axis: 30,000 m/min, rapid traverse Z-axis: 30,000 m/min, table width: 550 mm, table length: 450 mm, type of input current: three-phase, table load: 350 kg, overall weight: 5,500 kg, workpiece weight (max.): 350 kg, input frequency: 50 Hz, controller manufacturer: Heidenhain, controller model: TNCi530i, operating hours of spindle: 5,303 h, Equipment: documentation/manual, rotational speed infinitely variable, High-Speed Milling Machine HSC500/3 HSC500 - 3 Axis Annual maintenance Spindle operating hours HVC140: 5303h Travel range X/Y/Z: 700/590x580x360 mm Actual machining area: 580x530 mm Table area: 550x450 mm Workpiece weight: 350 kg Distance table to spindle nose: 160/520 mm Machine dimensions (W x D x H): 3200x2250x3000 mm Rapid traverse: 30 m/min Equipment: Heidenhain iTNC530i control Prepared for dust extraction Tool changer with 60 stations, HSK40 (Minimum quantity lubrication) Ljdpfxoy R U Aze Al Tjhl Adjustable air nozzle Tool length measurement with Blum laser Workpiece measurement with Renishaw OMP-400 touch probe Additional lighting Electronic handwheel with enabling switch Milling spindle: Steptec HVC140-15/42 42,000 rpm, 5303 operating hours MMS Lubtools 3 kW cooling system Loading door at rear of machine Length compensation, temperature compensation for accuracy package Warranty: 3 months (milling spindle excluded) Transport, commissioning, training Options on request

Condition: like new (used), Year of construction: 2025, operating hours: 100 h, functionality: fully functional, turning height: 1,500 mm, workpiece weight (max.): 8,000 kg, turning diameter: 1,700 mm, feed length X-axis: 1,100 mm, feed length Z-axis: 1,200 mm, faceplate diameter: 1,450 mm, feed rate Y-axis: 300 m/min, feed rate Z-axis: 300 m/min, total width: 5,000 mm, total length: 5,500 mm, rapid traverse X-axis: 4,000 m/min, rapid traverse Y-axis: 4,000 m/min, type of input current: three-phase, rotational speed (max.): 200 rpm, rotational speed (min.): 200 rpm, spindle speed (max.): 200 rpm, table load: 8,000 kg, year of last overhaul: 2025, travel distance X-axis: 1,200 mm, travel distance Z-axis: 1,200 mm, stroke length: 1,200 mm, disc diameter: 1,450 mm, overall weight: 21,000 kg, tool weight: 3,000 g, power of the servo motor: 40,000 W, repeat accuracy: 0.01 mm, Equipment: documentation/manual, CNC vertical lathe SC17, completely modernized in 2025 with Fanuc control. The machine is in very good condition, fully functional, live and available for inspection and testing. Technical specifications: Maximum turning diameter: 1700 mm Maximum workpiece height: 1500 mm CNC: Fanuc (complete modernization in 2025) Condition: functional, live Type: vertical turret lathe Advantages: Recent modernization - no additional investment required Reliable Fanuc control system Suitable for large workpieces Video available on request. Price on request Lodpfxoyxfgmo Al Tjhl

Condition: used, Year of construction: 2009, functionality: limited functionality, turning diameter over cross slide: 830 mm, turning length: 1,250 mm, turning diameter: 580 mm, spindle bore: 103 mm, spindle speed (max.): 2,000 rpm, spindle speed (min.): 8 rpm, Equipment: rotational speed infinitely variable, Complete CNC component set Siemens 802 D – bed and guide rails ground Description: CNC component set / machine construction kit with Siemens Sinumerik 802D control. The machine is in an advanced state of reconstruction. Sold as pictured as a DIY project for completion. All components are present. Key highlights: • Mechanics: The machine bed and support have already been freshly ground and painted in RAL 5015. • Geometry: The mechanical geometry has already been professionally restored (optimal basis for high precision). • Control: Includes a functional Siemens Sinumerik 802D CNC control. • Feed drive SIEMENS, main motor regulator from Siemens • Completeness: All related parts and assemblies are in stock and ready. Perfectly suited for the reconstruction of a precise CNC machine. Sold ex-works as inspected, without warranty. Technical data of the metal lathe MEXPOL TUB 830 C in the condition it was in before being disassembled: • Maximum turning diameter over bed: 830 mm • Maximum turning diameter over slide: 580 mm • Maximum bar diameter: 103 mm • Maximum turning length between centers: 1250 mm • Rapid traverse rate in X/Z axis: 10 m/min • Spindle speed range: 8–2000 rpm • Number of steps for adjusting the spindle speed: 3 • Diameter of the front spindle bearing: 140 mm • Power of the spindle drive: 15 kW • Maximum spindle torque: 2100 Nm • Bed width: 520 mm • Height of the centers above the bed guides: 420 mm Lhjdpfxey Sub Ho Al Tsl • Diameter of the tailstock quill: 105 mm • Extension of the tailstock quill: 200 mm • Taper of the tailstock quill: Morse 6 • Drive of the X-axis: SIEMENS motor (torque X-axis: 11 Nm) • Drive of the Z-axis: SIEMENS motor (torque Z-axis: 18 Nm) • Coolant pump capacity: 25 l/min • Power of the coolant pump motor: 0.18 kW • Speed of the coolant pump motor (50 Hz): 2800 rpm • Installed power: 22 kW • Power supply: 3x 400 V; 50 Hz Equipment of the lathe TUB 830C: • CNC control: SIEMENS SINUMERIK 802D Sales and delivery conditions: • Loading: Loading onto your transport vehicle is included in the price. • Delivery: Ex-works Hilden. • Validity: The offer is subject to change – subject to prior sale (valid only while stocks last).

Condition: like new (used), Year of construction: 2019, Technical Data: Cross-cutting line with punching unit Strip running direction from the operator's side: right to left Coil changing side in strip running direction: left Operator's side, straightening machine in strip running direction: left Raw material: • cold-rolled strip: S320GD; S350GD; S380GD (strip-galvanized structural steels) • plastic-coated steel strip • aluminum • basically dry surface or commercially oiled • laminated strip • stainless steel Uncoiler: Type: Power Coil M-BS 1600 2 coil loading stations The coil storage track is designed so that a distance of 900 mm remains between 2 coils with an outer diameter of 1600 mm Loading semi-automatic Strip width 200 – 1600 mm Max. coil weight: 16 tons Coil diameter inside uncoiler: 508 - 610 mm Coil diameter outside uncoiler: 900 - 1600 mm Spreading range 470 – 625 mm Machine frame movable on linear guides Spreading hydraulically Strip withdrawal from the coil automatically Coil side guidance automatically, 4-point coil side guidance Press roller, rubberized, centrally positioned on the strip, hydraulically Electrical locking of lifting and traversing movement Control system: Control concept LBF – Control Concept LSV SCHULER Cross-cutting shear: Type: SCHULER HSU-1600 Shear gap adjustment is carried out by motor The shear is used to cut the strip end at a right angle before processing the first part of a production sequence. Bridging roller bed: Arrangement of the bridging roller bed upstream of the straightening machine Type: VOMA C1600 N Passage, max. strip width 1600 mm Length of bridging roller bed 1050 mm Material running height in the straightening machine 1600 mm Straightening machine: Type: SCHULER SVH 12-53-70-96 / 160-1600 Straightening speed max. 60 m/min. Straightening speed min. 5 m/min. Number of straightening rollers 12 pcs. Diameter of infeed rollers 160 mm Diameter of straightening rollers 3 x 53 mm, 3 x 70 mm, 6 x 96 mm Loop radius 1600 mm Material running height in the straightening machine 1600 mm Strip side guidance automatically Support rollers to prevent roller deflection All-roller drive Looping unit: Threading process in the direction of roller feed via looping bridge, remote-controlled Automatic loop control for continuous straightening process Loop depth below floor approx. 2,500 mm Lhjdpozzrutjfx Al Tel 4-point guidance through 2 sequentially arranged strip side guides To increase feed accuracy, the feed length is recorded by means of a measuring wheel (arranged in front of the feed rollers) Roller feed: Type: SCHULER AC-RP-160-1600 Feed rollers, diameter 160 mm Loop radius 1600 mm Material running height above floor 1200 mm Drive, upper and lower roller, servo drive via a common distributor gear Special coating of the feed rollers Max. acceleration 15 m/s² Brake rollers: Brake rollers generate the strip pull during the rewinding of the strip material from the system onto the coil, in a generator-like manner Adjustment system hydraulically Punching unit with NC tool holder: Type: SCHULER HSU-1600 Design: Double C-frame Punching unit designed as 2 C-frame units, which can be traversed transversely to the strip direction by means of 2 servomotors, for accommodating the punching tools Number of punching tools per side max. 6 pcs. Punching tool, servomotor-driven, 90° rotatable 1 punching cylinder per punching tool Punching force min. 580 kN Max. hole diameter ∅ 90 mm for material thickness 4 mm Manufacturer of punching tools: WILSON TOOL Elevating table: Type: LAWE

Condition: like new (used), Year of construction: 2020, functionality: fully functional, power: 2 kW (2.72 HP), input frequency: 60 Hz, input voltage: 575 V, overall weight: 750 kg, Brand new twin-shaft batch mixer from BHS-Sonthofen for the intensive and homogeneous mixing of various bulk materials. Technical data: Lodpfx Ajzumpxsl Tshl Type: DKXC 180 Year of manufacture: 2020 Nominal capacity: 180 liters / 0.18 m³ Drive: 2 × 5.5 kW Voltage: 575 V / 60 Hz Weight: approx. 750 kg pneumatically operated discharge flap Location: Canada The electrical control system was manufactured according to Canadian regulations and must be inspected for operation in Europe and, if necessary, modified to comply with European regulations. The mixer has never been used. Technical specifications are subject to change without notice and are offered for sale subject to prior sale.

Condition: used, Year of construction: 2005, functionality: fully functional, input voltage: 400 V, RONDO SCM 50 Croissomat – Automatic croissant line Compact, professional line for cutting, separating, and automatically rolling croissants from a sheet of dough. Production up to 4,500 pieces/hour, depending on the format. Working width approx. 530–560 mm Automatic cutting of triangles Interchangeable dies according to the desired format Automatic separation of rows Automatic transfer to the rolling unit Adjustment of croissant tightness Suitable for different croissant formats and rolled products Ledpfx Asz Aux Dol Tshl Belt speed up to 9 m/min Compact design, ideal for high-volume artisan bakeries and semi-industrial facilities.

Condition: used, Year of construction: 2003, functionality: fully functional, Well-maintained slicer. Lhodpfx Ajzfizxol Tol

Condition: good (used), Year of construction: 2019, functionality: fully functional, New price including transport and installation approx. €850,000 net. The machine was professionally disassembled by qualified technicians and subsequently stored. An inspection at the location in the Netherlands is possible after prior appointment. Technical data: Lhedpfx Ajz Aquhol Tjl Manufacturer: SCM Stefani Type: One 108 Cell Year of construction: 2019 Operating hours: approx. 5,600 Feed speed: 10–40 m/min Maximum speed with pickback: 30 m/min Workpiece length: approx. 250–3,000 mm Workpiece width: approx. 130–1,200 mm Workpiece thickness: 10–60 mm Maximum workpiece weight pickback: 80 kg Machine length edge banding machine: approx. 11,550 mm Installation area of the complete cell according to layout: approx. 30,270 × 13,166 mm Working height: approx. 970 mm Connection: 400 V / 50 Hz with neutral conductor Workpiece feed: Motorized feed roller table Easy Order BN+ automatic workpiece feed Automatic alignment for longitudinal and transverse processing Servo-controlled workpiece centering Automatic adjustment to different workpiece dimensions Large lateral workpiece support Edge and glue system: Nordson AltaPUR 4HO PUR hot melt unit Melt-on-demand technology Melting capacity up to approx. 6 kg/h SGP glue reservoir with CNC-controlled glue metering Additional interchangeable SGP glue reservoir Separate preheating trolley for one glue reservoir Workpiece edge preheating Automatic positioning of the edge guide and pressure rollers 12-position vertical edge magazine with automatic edge changing Processing of roll material up to 3 mm Designed for thin edge, 20° bevel, and radii R1, R1.5 and R2 Machining units: Pre-milling unit RT-H/RT-X with 2 × 4 kW Electronic positioning of the pre-milling unit Trimming unit YU/SP-1000 with automatic saw blade inclination Flush-cutting and pre-milling unit R-E CNC-controlled RSU-E Hi-Drive Multiedge fine milling unit Processing of thin edge and R1, R1.5 and R2 Round 4 four-motor corner rounding unit Automatic selection of four profiles MX80 HSK milling unit with 10 kW CNC-controlled horizontal and vertical positioning Automatic pivoting from 0–90° Suitable for continuous or recessed grooves on the top, bottom and workpiece edge CNC-controlled RCS-E Multiedge radius drawing blade unit Edge sanding unit GT with oscillating sanding belt Two glue seam drawing blade units RCA/2C Polishing unit SP/F with oscillating Riepe polishing pads Spraying devices: Release agent spraying device at the machine infeed Antistatic and coolant spraying device Spraying device for sensitive or foiled edges Cleaning agent spraying devices for the glue seam drawing blades Spraying device for the first pressure roller Automatic pickback return: Gantry return system with three servo-controlled axes Workpiece pick-up via vacuum gripper Automatic rotation by 0°, 90°, -90° and 180° Automatic return to the machine infeed Up to 10 return cycles per minute without rotation Up to 9 return cycles per minute with 90° rotation Motorized conveyor belts Additional second unloading station Central control via the machine control system Location: Netherlands Inspection: possible after prior appointment Condition: professionally disassembled and stored Availability: short notice Price: on request The technical data were compiled based on the available original documents. Errors, changes and prior sale are reserved.

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, turning diameter over cross slide: 550 mm, turning length: 520 mm, turning diameter: 350 mm, spindle bore: 76 mm, spindle speed (max.): 4,500 rpm, travel distance X-axis: 210 mm, travel distance Z-axis: 579 mm, spindle motor power: 18,500 W, total height: 1,700 mm, total length: 3,000 mm, total width: 1,600 mm, overall weight: 4,500 kg, chuck outer diameter: 250 mm, spindle nose: A2-6, bar diameter (max.): 76 mm, controller model: FANUC 18i-TB, Equipment: documentation/manual, CNC turning center with FANUC 18i-TB control. Main spindle with 10" chuck, equiped with subspindle and Live tool (C-axis) max turning diameter ~13.8" (350 mm), max turning length ~20.5" (520 mm), bar capacity ~3.0" (76 mm), and spindle bore ~4.0" (102 mm). Lodpsyywufjfx Al Tohl

Condition: excellent (used), Year of construction: 1995, functionality: fully functional, Equipment: documentation/manual, CNC-controlled vertical machining center AXA VSC-3-3000-M Year of manufacture: 1995 Control system: Heidenhain TNC 407 Technical data: X-axis travel: 3000 mm Y-axis travel: 420 mm Z-axis travel: 480 mm Table size: approx. 3000 x 500 mm Spindle connection: SK40 Speed range: up to 6000 rpm 22-tool automatic tool changer Coolant system Heavy-duty frame construction Special features: Additional angular/universal milling head 4-/5-axis machining possible Flexible machining of complex workpieces Ideal for toolmaking, mechanical engineering and single-part production Lsdpfx Aloy U Hy Te Tjhl The machine is in good condition. Inspection under power is possible by arrangement.

Year of construction: 2007, condition: used, functionality: fully functional, machine/vehicle number: 301599, Rampf DC-CNC Working area: 800x400x200 mm Lodozzb Hljpfx Al Tohl Number of components: 3 (see photos) 1 x Isocyanate 2 x Polyol Temperature control unit Complete documentation available Details upon request.

Year of construction: 2013, condition: ready for operation (used), Portable 7-axis coordinate measuring system ROMER Infinite 1.0 SC 5028SC. Measuring range diameter: 2800mm, point repeatability: approx. +/-0.045mm - 0.050mm, volumetric length measurement uncertainty: approx. +/-0.064mm - 0.075mm, wireless communication: Wi-Fi 802.11b/g, battery operation, software base: WinRDS driver compatible with measurement software solutions PolyWorks, PC-DMIS, PowerInspect, Metrolog. Including integrated balancer, transport case, probe set 6mm, 15mm, tip, mounting plate with 3 magnets, calibration bar with calibration certificate. Inspection by appointment possible. Ljdpfx Aoyk Hcrel Tshl

Condition: good (used), Year of construction: 1999, power: 5.5 kW (7.48 HP), Equipment: CE marking, For sale is a robust and precise jointer and thicknesser from the German quality manufacturer Panhans. The machine is equipped with a Centrofix cutterblock. This quick-change system – similar to the Tersa cutterblock – allows for easy cutter replacement without time-consuming adjustment of the cutter knives. Technical data and features: +Manufacturer: Panhans +Type: AD 440/445-B +Year of manufacture: 1999 +Planing width: 630 mm +Motor power: 5.5 kW +Operating voltage: 400 V +Total length of the jointer tables: approx. 2,300 mm +Centrofix cutterblock +Cutterblock speed: approx. 5,000 rpm +Digital display for planing thickness +Electromotive adjustment of the thickness table with the push of a button +Two rollers in the thickness table +Automatic workpiece feed +Two feed speeds +Massive, finely planed cast iron tables +Folding jointer tables +Swiveling fence up to 45° +Dust extraction connection +Motor brake +CE version Ledezz Nk Eepfx Al Tohl The robust Panhans construction ensures smooth operation and clean planing results. The digital display, the electric thickness table adjustment, and the Centrofix cutterblock allow the machine to be operated comfortably, quickly, and precisely. Ideally suited for professional use in carpentry shops, joineries, and woodworking shops. The machine can be demonstrated under power by prior arrangement. Shipping via freight forwarder is possible. You will receive an invoice with VAT shown. Price: €13,685 including VAT - €11,500 net Subject to prior sale and errors in the technical data.

Condition: used, Year of construction: 2008, Technical details: turning diameter: 410 mm turning length: 500 mm control: Fanuc 21i TB standard turning diameter: 275 mm travel -x axis: 277 mm travel -y axis: 82 (±41) mm travel -z axis: 500 mm Spindle 1 RPM: 4500 1/min Spindle 1 Power: 18,5/18,5/15 kW Spindle 1 max. bar diameter: 65 mm turret stations / rotary tool stations: 12/12 Power rotary tools: 5,5 kW RPM of rotary tools: 6000 1/min total power requirement: 39,2 kVA weight of the machine ca.: 6,2 t dimensions of the machine ca.: 3,1 x 2,0 x 2,2 m collet chuck: Hainbuch Accerories Chip conveyor Robot interface High precision Turning and Milling Centre with Y-axis and robot loading. Stäubli Robot for shaft loading. Lsdpjzd Un Isfx Al Tohl *

Condition: good (used), Year of construction: 2012, Lightly used mixing, dispensing, and adhesive application system with a gear pump in good condition: t-s-i mastermix gear basic – Mixing and dispensing system for 2-component silicone adhesives – Two-component gear pump dispensing system – Hose set, 2.5 m, 2-component dispensing gun – Siemens S7-200 control system – Overpressure/underpressure cut-off – Pot life monitoring with acoustic warning – 200-liter component A container – 20-liter component B container Lodpfx Aszq S Ifel Tshl – Swivel arm extension 800 mm – Swivel arm height increase 300 mm – Hose set extension 1000 mm – Automatic dispensing when in the "parking" position – Year of manufacture 2012, rebuilt by T-S-I in 2016/17 – System was lightly used – Sale from location Karlsruhe / Southern Germany – Inspection possible by arrangement

Condition: used, Year of construction: 1999, operating hours: 36,151 h, functionality: fully functional, Disassembly, loading, and transport are the responsibility of the buyer. Ledpozzvxcsfx Al Tshl Sale only within the EU.