Edge banding machine

Lange B 590K-PUR

Condition: excellent (used), SINGLE-SIDE EDGE BANDER (LEFT-side) Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 - in stips / lippings mm max 1 Panels thickness (min/max) mm 14 / 60 (LASER - Max 50) Numerical Control ICOS Open Feeding speed (adjustable) m/min 6 - 30 Top pressure system with rubber belt Spraying unit (Anti-sticking liquid) Guedpfsi Hn Srox Acfec In-feed fence, adjustable by N.C. Panels in-feed (servo) system A1 / 15 Pre-milling Unit (vertical joint trimmers) 08.378 (2 x Kw 4,5) adjustable by N.C. Glueing Unit (P.U.R. Glue + Quick Melt unit) 283.201 + 283.203 Glueing Unit (Thermofusion with Laser) Laser System LASERLINE Spraying Unit (for anti-release liquid) Band Pressure zone + Edge coils supporting unit (No. 36 + 12 reels) Snipping (end-cutting) 08.42 (Kw 0,2 x 2) work speed up to 30 m/min (0°-25°) Rough Trimming unit 08.0555 HS/LS1 (Kw 1 x 2) Fine Trimming unit (Multi-profile, by N.C. adjustment, for 4 profiles) 08.0587 (Kw 0,66 x 1) Multi-Profile Copying unit by N.C (fine + contour trimming) KFA 30 (Kw 0,5 x 1) max 30 m/min Profile Scraping unit (Multi-profile, by N.C. adjustment, for 4 profiles) 08.0516 Glue scraping unit 08.521 Spraying Unit (for polishing liquid) Buffing unit 08.614 (Kw 0.25 x 4) No. 2 Milling grooving units 08.190 (Kw 4,5 x 2) swivelling 90°/180°/270° (adjustable by CN)

Condition: excellent (used), FULL LINE of 4 Side Sizing-Milling & Edge Banding (also SOFTFORMING), through-feed drilling and splitting of panels. Complete with fast automatic handling. Composed of the following machines: A) Loader (Bridge-Frame) "RBO (BIESSE)" Mod. Winner C (1) B) 1st Double-side Sizing & Edge Bander "BIESSE" Mod. Stream SB1 11.0 Softforming C) 1st 90° Turning device (Lengthwise to Crosswise) "RBO (BIESSE)" Mod. GPK-1 D) 2nd Double-side Sizing & Edge Bander "BIESSE" Mod. Stream SB 2 9.5 E) 2nd 90° Turning device "RBO (BIESSE)" Mod. GPK-2 (straight or Crosswise to Lengthwise) F) Multi-Borer with CN "BIESSE" Mod. Techno FDT CN (with 2 horizontal working units, 6 vertical bottom working units and 3 vertical top working units) Gedpottgy Hjfx Acfjuc G) Multi-Borer with CN "BIESSE" Mod. Techno FDT CN (with 2 horizontal working units, 6 vertical bottom working units and 3 vertical top working units) H) 3rd 90° Turning device "RBO (BIESSE)" Mod. GPK-3 (straight or Crosswise to Lengthwise) I) Splitting Saw (Splitter) Lengthwise "GM (for BIESSE)" Mod. Split 4-84 LT L) Stacker (Bridge-Frame) "RBO (BIESSE)" Mod. Winner SC (2)

Condition: new, Year of construction: 2026, Comparable to: e.g. Emmegi Double mitre saw for steel Cutting length: 5,000 mm Equipped with 7 NC axes for length positioning, outward and inward saw blade inclination, saw blade feed, and saw motor speed control Torsion-free welded construction with longitudinal linear guideways 2 x saw motors, each 4.5 kW Saw blade speed: 0–250 rpm Saw feed motorized from rear to front Feed speed infinitely adjustable Godoyinu Hopfx Acfeuc Motorized angle adjustment between 135° and 45° Suitable for HSS circular saw blades, Ø 400 mm Pneumatic protective covers Water cooling with pump and coolant tank Left saw unit fixed to the base frame, right unit motorized and traversable Positioning accuracy: ± 0.15 mm Max. traverse speed: 25 m/min Length positioning compensates for saw angles and profile height Each saw head fitted with three horizontal and vertical profile clamps; in the event of pressure loss, the horizontal cylinders remain clamped Pneumatically swivelable material support between the saw heads 15” touchscreen Single cut processing Processing of cutting lists Creation of cutting lists via keyboard Import of cutting lists via USB flash drive or network interface Corner cutting Overlength cutting Short cuts from 5 mm cutting length Crosscuts Available options: Micro-spraying unit Saw head inward inclination increased to 150° Label printer Barcode scanner Additional network interface and teleservice agreement

Condition: new, • Working capacity 3300mm X, 200mmY, 180mm Z Gsdpfxjn Nv S Ts Acfouc • 1 x vertical electro-spindle 7kw with saw • 1 x vertical electro- spindle 7kw 12 – 18000 rpm • 1 x electro-spindle kw1.7 with point to point vertical / horizontal drilling group • 1 x horizontal electro-spindle 5.6kw 12-18000 rpm • 4+4 work piece holding benches moveable on the X axis/ Each fitted with adjustable pneumatic workpiece clamps • L/H and R/H retractable work piece reference stops • Stand alone electrical control cabinet with hand held remote control for machine set up • Simple parametric programming with 3D working models • Perimeter safety cabin with front doors, vertical operation, synchronised with machine cycle

Condition: new, Year of construction: 2025, Table milling machine minimax tw 45c With aluminum sliding carriage and swiveling milling spindle - high performance for a low investment Item number 5502045 Brand Holzkraft / SCM TECHNICAL DATA Dimensions and weights Guedpfehp Rcyex Acfjc weight (net) ca. 290kg Connection suction suction connection diameter 2 x 120mm Working table Working table length 1000mm Sliding carriage length 1000mm working table width 435mm sliding carriage width 270mm table height 900mm Installation information Space requirement length 1945mm machine body width/depth 710mm Space requirement width/depth 2220mm Working area length 1600mm Explanation of space requirements The dimensions take into account maximum travels or useful lengths. Working area Width/depth 1600mm Machine body Length 1000mm Explanation Working area Please add the dimensions given with the space requirement to obtain the free installation area recommended for the machine. Electrical data Supply voltage 400V Power drive motor 5,0kW Mains frequency 50Hz Milling spindle Spindle inclination 0 to -45° Spindle speed(s) 3500/7000/10000min¯¹ Useful length of spindle 100mm Spindle mandrel diameter 30mm spindle protrusion max. over table 130mm Milling tool diameter max. Tool diameter max. lowerable 180mm Tool diameter max. tenon milling 275mm tool diameter max. profile milling 210mm SUPPLY Arch milling protection hood Anodized aluminum sliding carriage Telescopic miter fence Aluminum stop jaws

Condition: refurbished (used), functionality: fully functional, edge thickness (max.): 15 mm, overall weight: 4,000 kg, OTT edge banding machine type Strom+ Optional with return system TransCompakt or TransLift. The machine is factory reconditioned and is sold with warranty in Germany. New tools, new chain plates and belts. For PUR glue and EVA glue. Alternatively, we also have access to a Tornado+ and StrongEdge, both factory reconditioned. Guodpoyn Am Ijfx Acfec

Condition: new, - New -Description:- For sawing, milling, surface planing, thickness planingand optional slot drilling- The work tables made of heavily ribbed gray cast ironand the underframe made of welded steel guaranteeTorsion resistance and vibration-free work- Unique in this performance class: smootherAluminum format slide, anodized, with ball contact system- Swiveling saw blade from 90 ° - 45 °- Table bracket with graduated scale and aluminum crosscut fencefor angled cuts on plates and large workpieces- Planing unit with TERSA quick change systemwith three planer knives- Helical-toothed steel feed roller for constantWorkpiece infeed when thicknessing- curved milling protection hood for profiling,with fine adjustment as standard- Milling unit with two speeds- The units are driven by three independent motors- Made in Italy qualityTechnical specifications:Dimensions and weightsWeight (net) approx. 245 kgDressingPlaning table width 300 mmPlaning table length 1200 mmAngle of inclination saw / planer fence 90/45 °Chip removal ssing 3 mmConnection suctionExtraction nozzle diameter 4 x 120 mmSuction nozzle diameter of the saw blade guard 60 mmInstallation informationRequired space length 2460 mmSpace requirement width / depth 2155 mmExplanation of space requirements: Take the dimensions into accountmaximum travels or useful cknessThickness table length 450 mmThickness table width 300 mmWorking height thickness min. 3 mmWorking height thickness max. 200 mmChip removal max. Thickness 3 mmElectrical dataConnection voltage 400 VMains frequency 50 HzNominal operating mode drive motor S6Duty cycle of drive motor 40%Drive motor power 3 x 1.8 kWSliding carriage and tableFormat sliding carriage length 1140 mmFormat sliding carriage width 201 mmFormat sliding carriage height 70 mmTable length 1024 mmTable width 224 mmTable height 900 mmMilling spindleSpindle inclination 0 °Spindle mandrel diameter 30 mmUsable length of the spindle 75 mmSpindle speed (s) 5000 - 7500 min? ¹Milling tool diameter l diameter max. 160 mmTool diameter can be lowered 180 mmTool diameter max. Tenon milling 275 mmPlaner knife shaftPlaner shaft type TERSAPlane shaft diameter 62 mmNumber of planing knives 3 pcsCircular saw unitTrimming length 1200 mmCutting width with rip fence 540 mmMax. Cutting width to the left of the saw blade 1200 mmSaw blade inclination 90 - 45 °Max. Cutting height at 90 ° 67 mmMax. Cutting height at 45 ° 40 mmMax. Saw blade projection 90 ° 75 mmMax. Saw blade projection 45 ° 60 mmFeedFeed speed 6 m / minScope of delivery:- Tersa quick-change planer knife shaft- anodized aluminum sliding table- Multifunctional stop for parallel cuts and surface planing- Table extension arm with crosscut fence and stop jaw- Eccentric clamping armItem no .: 5500030 Gjdsvwf Enopfx Acfsuc

Condition: excellent (used), SINGLE-SIDE EDGE BANDER (LEFT-side) Edges (band in rolls) thickness (Min/Max) mm 0,3 - 3 Panels thickness (min/max) mm 8 - 60 Numerical Control ICOS open compact Feeding speed (adjustable) m/min 6 - 30 Top pressure system with rubber belt, Spraying unit (Anti-sticking liquid) Automatic and accurate Panels in-feed system Mod. A1 / 15 In-feed fence, adjustable by N.C. Panels in-feed system Bar Code Reader Pre-milling Unit (vertical joint trimmers) by N.C. 08.379 (2 x Kw 4,0) Lamps to heat the workpieces side Glueing Unit (P.U.R. Glue + Quick Melt system) VTG + 283.203 Band Pressure zone. Height adjustment of the band by N.C. Edge coils supporting unit (reels N°) 12 Godpfx Asltmnlscfouc Snipping (end-cutting) unit 08.42 / 30 / B (Kw 0,66 x 2) (PNEU 0°-25°) 30m / min Rough Trimming unit 08.0555 (Kw 1 x 2) Fine Trimming unit (Multi-profile, by N.C.) 08.0587 (Kw 0,66 x 2) 4 PROFILES HSK 25 Spraying Unit (for sliding liquid) Multi-Profile Copying unit by N.C (fine and contour trimming) KFA 30 (Kw 0,5 x 1) 30m/min Profile edge scraping unit (Multi-profile, by N.C.) 08.516 (4 PROFILES) Glue scraping unit 08.521 Spraying Unit (for polishing liquid) Buffing unit 08.617 (Kw 0,25 x 4). Free space Milling grooving unit 08.190 (Kw 4,5 x 1)

Condition: new, Year of construction: 2025, CNC-controlled drilling, gluing, and dowel insertion machine Complete in standard configuration with: - Support with linear guide consisting of: 1 pc. single-spindle horizontal drilling unit, motor 0.65 kW, stroke 70 mm Tool speed selectable via operator software (3000/5000/8000 rpm) 1 pc. blow-out, gluing, and dowel insertion station for dowels Ø 8 mm, dowel length 25–50 mm - Fully automatic, electronically controlled central lubrication - X-axis NC controlled, with working length 700 mm, max. traversing speed 95 m/min - Z-axis manually adjustable via mechanical digital counter, position on support table 5–40 mm - Dowel insertion projection adjustable from 7–20 mm via mechanical digital counter, drilling depth 0–35 mm (with drill length TL 70 mm), automatically set with insertion projection - Closed glue system with 6 bar glue pressure via glue nozzle, for glues with viscosity from 150 to 350 mPas - Glue quantity steplessly adjustable via operator software - Selector switch GLUE/WATER to flush glue system, each with: 1 stainless steel container for 7.5 kg glue and 7.5 l water - Indicator lamp for residual glue level in glue container - 1 pc. left side stop, 1 pc. right side stop (all removable) - 2 pcs. start buttons for individual operation with 1–2 workpieces - 2 pcs. pneumatic angled clamping cylinders 10° for workpiece thickness up to max. 80 mm, workpiece length (Y) min. 70 mm - 1 pc. extraction funnel, connection Ø 80 mm - 1 pc. TCT controller with: Integrated industrial PC, incl. Beckhoff TwinCAT soft PLC, operating temperature range 0–50°C, 15" capacitive touchscreen TFT industrial display, operating system: WINDOWS 10 IoT LTSC (long term support channel) - Programming via menu-guided user software, drilling distances freely programmable with Godpew Sgm Hofx Acfeuc ABSOLUTE, RELATIVE, or GRID dimensioning, automatic workpiece mirroring and process optimization, 2 working fields assignable with different programs, graphical workpiece display, parametric programming, zero-point shift, programmable work lists, plain text error diagnosis - Integrated options: - Electronic optical glue monitoring system G.I.C. (Glue Insert Control) for 1 pc. glue nozzle, art. no. 0470-0810 - 1 EASY CLEAN system, for automatic test glue shots before starting the drilling/gluing/dowel insertion program. E.C.S. for 1 pc. glue nozzle, art. no. 0471-Z010 - 1 single-spindle vertical drilling unit from ABOVE, 0.65 kW, (3000/5000/8000 rpm), position (Y) manually adjusted via mechanical digital counter Adjustable from 5–40 mm, drilling depth (Z) max. 30 mm (with drill length TL 57 mm) Workpiece thickness (Z) max. 50 mm, workpiece length (Y) min. 130 mm (incl. drilling depth compensation, e.g., for Häfele Minifix) Art. No. 0471-0830 - 4 vertical angled clamping cylinders 10° with mount, additional, Art. no. 0470-0850 Available: short notice

Condition: new, Bore diameter variabel mm Number of heads horizontal 3 St. Number of heads vertical 4 St. weight 1500 kg Dimensions (L/W/H) 4800x1600x2400 mm Width mit Auflage 2300 mm Götzinger Power Drill Type BF 297 With the Götzinger PowerDrill you can, depending on the type and design: Griffoliven drill on the loose frame part or for finished wings, with multi-spindle drilling head, quick-change, also for milling of the lock case for WK 2 or intermediate gear Ecklager drill on loose frame part, with Mehrspindelbohrkopf, quick-change, corner-oriented over stop or custom made (tilt window) Drill vertically from above for fitting, pre-drill for clip on loose frame part Milling vertically from above for pushers, profile cylinders, 3-D hinges Horizontal drilling with 2 drilling units, different drilling diameters, Dowel drill front and long side, plywood / fighter, sprouts, Corner connection, front door etc. Milling horizontally for lock case / fitting etc. machine description Base frame in stable welded construction, linear guide for the X-axis Table top 3,000 x 200 mm Guedpjd Ih Hqjfx Acfec 6 clamping cylinder pneumatic with auto. Ausweichhub 2 side stops for machining on the front side, manually swiveling in and out 2 longitudinal stops can be manually swiveled in and out Travel: X-axis - 3,000 mm working length Y-axis - 120 mm Z-axis - 105 mm Aggregate: 1 drilling unit (unit 1) vertically from above, drill motor 1,1 KW Speed ??1,500 - 12,000 rpm, 1 spindle, collet holder ER 20 1 Bohraggreagt (unit 2) vertically from above, drill motor 1,1 KW Speed ??3,000 rpm, with drill head quick change device 1 boring head BKF 3, olives, quick-change 1 boring head BKF 3/2 corner bearing, quick-change 1 milling unit (Agg.3) vertically from above, milling motor 2 KW, 1,500 - 16,000 rpm, collet holder ER 25 2 horizontal drilling units (Agg.4 and 5) 1.0 KW, 1.500 - 12.000 U / min, Collet holder ER 20 1 milling unit horizontal (Agg.3) 2.0 KW, 1.500 - 16.000U / min, Collet holder ER 20 Electro-pneumatic control with 3-axis control X, Y, Z NC positioning controller make B + R input via TFT display 10 " Machine complete with 1 set of drilling tools dm 6, 8, 10 and 12, 2 roughing carbide cutters HM dm 16, CE compliant, ready for connection Suction connection: 1 x dm 120 Power connection: 1 x 400 V, 16 amps Air connection: 1 x LW 9 mm OPTION: Longitudinal stops right / left with NC axis high / low programmatically, thus dimension input by folding / light measure possible, Dimension: LxWxH = 4.80 x 1.60 x 2.40 m - weight machine 1,500 kg (technical data according to manufacturer - without guarantee!)