Mitre band saw automatic machine

KARMETAL 350 ODG-PLC

Condition: new, Year of construction: 2026, The CORMAK HBS275 band saw for cutting tubes, profiles and bars is widely used in all locksmith and metalworking workshops where precision, quality and cutting speed matter. The model is equipped with a 0-60° swivel arm; the saw guides are based on sintered carbide. The frame construction ensures accurate and quiet operation. Machine characteristics Hnedpfxsudi Uns Aiget The horizontal metal band saw with swivel arm enables cutting in a plane perpendicular to the axis of the material being cut and at any angle within the range from 0 to 60°. The material to be cut can be fed manually or by any mechanical device, while the tool feed is automatic. The blade guides are equipped with special carbide plates and bearings. This has a major impact on blade guidance, service life, straightness, accuracy and cutting quality. Carbide guidance greatly reduces wear of the machine and blade. The machine is equipped with an efficient coolant pump with a closed coolant circuit. The saw arm is made of a single cast-iron casting and, together with the 27 mm wide cutting blade used in this saw, fully enables multi-series cutting of both profiles and solid materials. The vice is located in an adjustable bed and is equipped with a quick clamp. The blade guides are equipped with hard metal plates – sintered carbide and a rolling bearing system. It is precisely the SINTERED CARBIDE GUIDES that are responsible for the precision and straightness of the cut. The arm has been inclined at an angle of 25°, which increases blade durability and improves cutting conditions. A cleaning brush is mounted at the bottom of the arm to achieve excellent cleanliness and blade operation. The machine drive is transmitted via a worm gearbox. The machine has a three-phase motor with two cutting speeds and motor thermal protection. The shape of the upper part of the base forms a tray for draining coolant and collecting chips generated during material cutting. A cast-iron work table with a swivel arm and a control panel on a separate arm is mounted to the base. In the cutting process, the main cutting movement is the movement of the cutting blade, while the feed is the lowering of the arm. The arm lowering speed (cutting speed) is regulated by a hydraulic cylinder. The feed speed is adjusted on the saw control panel. Two cutting blade speeds are available: 37.5 and 75m/min. In the lower position of the arm (after cutting the material), the cutting blade drive is switched off automatically. Safety is ensured by cutting blade guards and micro-switches that stop the motor after the cutting cycle is completed or when any guard is opened; additional protection consists of automatic shutdown of the saw in the event of cutting blade breakage. The machine drive is transmitted by a motor with a worm gearbox. The motor with thermal fuse protects against overheating during operation. Technical data TOTAL POWER 1.5kW POWER SUPPLY 400V 50Hz ARM LOWERING ADJUSTMENT hydraulic cylinder BLADE LENGTH 2450 x 27 x 0.9 mm BLADE SPEED 37.5 / 75m/min VICE BASE HEIGHT 900 mm MACHINE DIMENSIONS (WITH ARM RAISED) (L x W x H) 1720 x 800 x 1800 mm WEIGHT 215 kg

Condition: excellent (used), functionality: fully functional, Year of construction: 2003, control type: manual, degree of automation: manual, actuation type: hydraulic, controller manufacturer: Tauring, controller model: digital readout, number of rollers: 3, shaft diameter: 70 mm, roller diameter: 245 mm, pipe diameter (max.): 100 mm, tube wall thickness (max.): 6 mm, overall weight: 1,300 kg, total length: 1,640 mm, total width: 1,220 mm, total height: 1,580 mm, power: 5.5 kW (7.48 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, Equipment: CE marking, documentation/manual, emergency stop, foot remote control, hardened rollers, Profile bending roll Tauring Alfa 70H2 year 2003 -Hydraulic section bending machine with digital readout -3 rolls powered driven - -dual pre-pinch pyramid roll configuration Shafts output 70 mm – Size of universal rollers 245 mm Lateral correctors left/right side hydraulic motorized operated Machine reversible can work with shafts vertical/horizontal Tooling: Hnodpfx Aieyx Dg Segjt -Set of universal rolls and spacers Pipe bending rolls set for tube 22,5 – 61 – 76 - ( see photos of the rolls in enclosed ) Power total installed 5,5Kw Vac 380/50 Dimension 1640 x 1220 x H1580 mm Weight 1300 kgs -CAPACITY CHART IN ENCLOSED

Condition: good (used), functionality: fully functional, Year of construction: 2007, machine/vehicle number: CA90H2 PIPE BENDING ROLL, shaft diameter: 90 mm, roller diameter: 260 mm, rotational speed (min.): 8 rpm, rotational speed (max.): 8 rpm, overall weight: 1,000 kg, total length: 1,260 mm, total width: 1,000 mm, total height: 1,260 mm, power: 3.68 kW (5.00 HP), input voltage: 380 V, type of input current: three-phase, operating speed: 8 mm/s, roll diameter: 260 mm, Equipment: documentation/manual, emergency stop, PROFILE BENDING ROLL SHAFTS OUTPUT 90 MM - PIPE BENDING ROLL MARGI CA90H2 YEAR 2007 SHATS OUTPUT SIZE 90 MM SET OF UNIVERSAL ROLLERS SIZE 260 MM LATERAL CORRECTOR ROLLERS LEFT/RIGHT SIDE SCREW ADJUST 4 SET OF ROLLERS FOR TUBE BENDING MM 61 - 78 – 90 – 116- CONSOLE ELECTRIC MOVABLE ON WHEELS ALL THE CONTROLS CENTRALIZED DIGITAL POSITION READOUT OF BENDING ROLLS UPPER ROLL DRIVEN MOTORIZED ELECTRIC POWERED WITH GEAR UNIT SIDE ROLLERS HYDRAULIC ADJUSTMENT POWERED INDEPENDENT WITH PISTON MACHINE REVERSIBLE CAN WORK WITH SHAFTS VERTICAL/HORIZONTAL. SAFETY AND EMERGENCY STOP EQUIPMENT INSTALLED WITH THE MACHINE MANUALS AND SCHEMATICS IN ORIGINAL ALONG WITH THE MACHINE Hnsdpfxjwkrr Te Aigot WEIGHT 1000 KG DIMENSION 1260 X 1000 X H 1260 MM

Condition: excellent (used), Year of construction: 2016, Cutting Capacity 0° round (tube): 300 mm Cutting Capacity 0° round (solid material): 180 mm Cutting Capacity 0° rectangular horizontal (hollow section): 320 x 290 mm Cutting Capacity 0° bundle (tube): 320 x 160 mm Cutting Capacity -45° round (tube): 300 mm Cutting Capacity -45° round (solid material): 110 mm Cutting Capacity -45° rectangular horizontal (hollow section): 300 x 280 mm Cutting Capacity -60° round (tube): 200 mm Cutting Capacity -60° round (solid material): 80 mm Cutting Capacity -60° rectangular horizontal (hollow section): 190 x 200 mm Cutting Capacity +45° round (tube): 270 mm Cutting Capacity +45° round (solid material): 110 mm Cutting Capacity +45° rectangular horizontal (hollow section): 270 x 200 mm Table height, material feed: 800 mm Main motor: 2.6 kW Cutting speed, stepless: 20 - 100 m/min Saw blade size: 3660 x 27 x 0.9 mm Machine dimensions (L x W x H): approx. 1800 x 950 x 1400 mm Net weight: 585 kg Accessories / Special features: • Semi-automatic swing-frame metal band saw • After the cutting cycle is started, the vice clamps automatically – after completion, it returns to its starting position • For mitre cuts from +60° to -45° with frequency inverter • Suitable for cutting stainless steel, tool steel, hollow profiles, and solid materials • Fully hydraulically controlled sawing functions • Saw drive with low-maintenance, oil-lubricated worm gear • Robust three-phase motor • Motor equipped with overload protection • Ball-bearing turntable • Saw arm inclined at 25°, resulting in longer saw blade service life • Saw arm swivels from +60° to -45° • Chip removal brush for optimal saw blade cleaning and maintenance • Frequency inverter: allows stepless adjustment of saw blade speed from 20 - 100 m/min • BRP – Saw band monitoring • Hydraulic vice with manual quick-release for lateral adjustment Hsdpsxz Dqmjfx Aigjnt • Limit switches control upper and lower saw arm positions • No need to set the upper end point • Length stop with scale, left-side removal 3 m • Cut detector • Swivelling control panel • Micro-spray device • 2 x roller conveyors: 3 m discharge left, 6 m feed right • CE compliant Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: good (used), Year of construction: 1996, Offer 24407 Technical Data: - 2 motor-driven rollers - Hydraulic adjustment of the top roller; pressing force: 18 t - Shaft diameter: 60 mm - Shaft rotation speed: 6 rpm - Roller diameter: 215 mm - Bending capacity: - Flat bar R 300 vertical: 80 x 15 mm - Flat bar R 300 horizontal: 120 x 25 mm - Square material R 300: 50 mm - Round tube R 900: 100 x 2 mm - Drive: 400 V / 1.5 kW - Includes: separate control panel with digital readout + foot switch - Forward / reverse operation - Side guide rollers Hnedpfxjy Ddrfe Aiget - Standard bending set for flat and angle material - Weight: approx. 1200 kg - Space requirement: approx. W 1000 x H 1750 x D 1250 mm

Condition: new, pressure 40.0 t stroke 285 mm flat steel 250 x 24 mm working feed 10.0 mm/sec return speed 10.0 mm/min work height max. 930 mm table: 660 x 1250 mm total power requirement 4.0 kW motor 400 Volt 50 Hz oil volume 40.0 l weight 800 kg range L-W-H 1450 x 800 x 1300 mm Furnishing : - electro-hydraulic horizontal bending machine - large, robust machine table made of hardened steel Hsdpfoxabhmox Aigont - Machine made of hardened and ground forged steel - Digital display for stroke setting * * Programming of 1x bend end point & 1x retract point possible - 1x tool set (1x bending punch / 1x 1V die) - infinitely variable adjustment of the bending speed and pressing force - 1x manual material stop - Free-moving dual footswitch - Machine can be moved with a pallet truck/stacker - Operation manual

Condition: new, Year of construction: 2026, Metal Cutting Band Saw CORMAK S-200RH The CORMAK S-200RH metal cutting band saw is a modern semi-automatic band saw designed for intensive operation in the metalworking industry. It enables cutting at angles from -45° to +60°, providing high precision, repeatability, and efficiency even when processing heavy sections. The machine combines precise blade guidance with automation of key functions, including hydraulic arm lifting/lowering and hydraulic vice control. Main advantages of the machine Hydraulic arm movement control (up/down) with smooth adjustment of lowering speed. Arm position memory function – automatic return to a predefined height. Swivelling saw arm from -45° to +60° with a clear angle scale. Hydraulic quick-clamping vice – suitable for cutting profiles and solid materials. Heavy cast iron saw arm – ensures rigidity and operational stability. Efficient coolant pump with closed-loop cooling system. CE safety system – including limit switches and emergency stop button. Construction and technology The band saw is built on a stable steel base with an integrated hydraulic unit and coolant tank. The saw arm is made from a single-piece cast iron construction, providing high resistance to vibration and twisting, which directly improves cutting quality. The blade guides are equipped with carbide inserts and roller bearings, ensuring accurate alignment and straight cutting of processed materials. A high-performance ABB M3V series motor and worm gear transmission provide two cutting speeds for optimal adaptation to different materials. Precision and work efficiency The machine enables fast and repeatable cutting of pipes, profiles, and solid materials, including very small sections starting from Ø5 mm. Automation of the cutting process (arm movement and hydraulic vice operation) significantly reduces operating time and minimizes operator involvement. The integrated blade cleaning brush maintains proper working conditions and extends blade service life. Applications The CORMAK S-200RH model is designed for: production workshops, steel construction plants, machine manufacturing industries, maintenance departments. Hodpfxji D D A So Aigent It is particularly suitable as a band saw for pipes and profiles in serial production and applications requiring high cutting accuracy and repeatability. Standard equipment Control console mounted on a separate pedestal Integrated hydraulic power unit Hydraulic vice Automatic arm lifting and lowering with position memory function Blade cleaning brush Coolant system with pump Bimetallic band saw blade Technical documentation (DTR) and CE declaration of conformity Optional equipment Material feeding rollers Laser cutting line guidance system Extended cutting length measurement system Semi-Automatic Metal Cutting Band Saw CORMAK S200RH Technical data Parameter Value Machine type Semi-automatic band saw Arm lifting and lowering Hydraulic, smooth adjustment Blade speed 36 / 70 m/min Angular cutting range -45° to +60° Vice Hydraulic Minimum cutting diameter Ø5 mm Minimum material length in vice 30 mm Vice base height 780 mm Cutting blade dimensions 27 × 0.9 × 2910 mm Total motor power 2.1 kW Machine dimensions (L × W × H) 1600 × 800 × 1400 mm Weight 530 kg

Condition: used, Year of construction: 1982, Technical details: cutting diameter: 120 mm dimensions of saw-blade: 425 x 30 mm cutting range 90 degrees: round: 120 mm height over floor: 800 mm electrical connection: 380 V / Hz. strokes per minute: 60 / 92 / 140 Hübe/min. total power requirement: 1,5 kW Overall size: ca. L:1,2 x B: 0,75 x H: 1,10 (Bügel angehoben) m Vice adjustable in longitudinal direction by loosening the nuts. Mitre cut and straight cut: 45° and 90° with cutting pressure and lifting hydraulics After the cut is completed, the machine switches off and the saw blade remains in the lowest position. Hnsdsu Nilaspfx Aigst Workpiece holder via fixed jaw and clamping jaw, with hand crank Coolant device in the base limit stop *

Condition: used, mileage: 187,000 km, power: 96 kW (130.52 HP), first registration: 11/2019, overall weight: 3,500 kg, next inspection (TÜV): 03/2026, color: white, emission class: euro6, number of seats: 3, loading space volume: 18 m³, loading space length: 4,180 mm, loading space width: 2,040 mm, loading space height: 2,130 mm, Year of construction: 2019, Equipment: ABS, air conditioning, central locking, soot filter, tail-lift, ISUZU M21 with tail lift from our own fleet, with a history that can be checked. Equipment: cruise control, air conditioning, retarder, ABS, double fuel tank, on-board computer, electric windows, etc. Please call us at WhatsUp/Viber also) E-mail: Hnodpjxp Tndofx Aigst

Condition: used, Technical details: cutting diameter: 310 mm cutting width: 360 mm total power requirement: ca. 1,8 kW Miter cutting possible Workpiece clamping hydraulic bracket lowering hydraulic incl. roller conveyor entrance approx. 2100mm and exit approx. 2700mm * Hjdpfx Aou Niifoigont