Angle roll shaft diameter 130 mm

FACCIN RCMI 130

Condition: excellent (used), Year of construction: 2013, controller manufacturer: ELFRAN Digital Read Out, number of rollers: 3, shaft diameter: 130 mm, overall weight: 5,800 kg, total length: 2,200 mm, total width: 2,400 mm, total height: 2,000 mm, Profile bending machine FACCIN - RCMI 130 MACH-ID 9451 Make: FACCIN Type: RCMI 130 Control: ELFRAN Digital Read Out Year: 2013 3 rolls driven 2 lateral guide rolls Digital readout for position rolls Set hardned universal rolls Set hardned profile rolls Horizontal and vertical:|Horizontal and Vertical Shaft Ø: 130mm Number of rolls: 3 Capacity flat: 240 x 30 x 1000mm Capacity Tube: 140 x 5 x 1500Ø x mm Iaedpfeyrq Dvex Af Ujt Capacity bar: 80 x 80 x 900mm Capacity T-Profile: 140 x 15 x 1400mm Capacity HEA-Profile: 160 x 1700mm Working speed: 0 - 6000mm/min. Side supports: 2 x Hydraulic side arms Length: 2200mm Width: 2400mm Height: 2000mm Weight: 5800kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 2009, condition: good (used), machine/vehicle number: 120P1109, OFFER 21407 Mot. tank-boiler turning device with rail trolley Technical data: - Total payload driven + travelling unit 40000 kg. - payload per vessel device 20000 kg - workpiece diameter approx. 500 - 3500 mm - Centre distance of the support rollers adjustable via trapezoidal thread spindle - roller diameter 500 mm - roller width 150 mm - driven unit with drive on both sides - infinitely variable rotational speed - manual remote control for Re- and Li.-run - drive 400 V - Both units are mounted on rail trolleys - space requirement with running unit approx. W 3800 x H 1150 x D 1350 mm - Space requirement with running unit approx. W 3600 x H 1150 x D 1350 mm Iaedpfx Afohcnhmj Ust - Weight attached unit approx. 2500 kg - Weight with running unit approx. 1800 kg

Year of construction: 1978, condition: used, pressure 100 t throat 380 mm stroke 400 mm power capacity 22 kW Iasdpfx Afslp U Dpo Ust dayligth 600 mm ram surface 600x500 mm table surface area 720x600 mm weight of the machine ca. 9 t

Condition: excellent (used), Year of construction: 2014, sheet width 2600 mm plate thickness 10.0 mm ST pre-bending 8.0 mm ST diameter of upper rolls ~ 220 mm side roll diameter ~ 170 mm diameter of lower rolls ~ 190 mm Isdpfxeylpz Hs Af Ueat Control konv. oil volume 80.0 Liter voltage 380 V total power requirement 5.5 kW weight ca. 5000 kg Dimensions (only the machine) ca. 3500 x 1550 x 1400 mm very good condition (!!) current new price incl. accessories approx. 120.000 Euro special price on request Equipment: - robust electro-hydraulic 4-roll round bending machine - 4-roll concept offers a wide range of bending and rounding options - Swivel-mounted control unit * Operation - control of all rollers or machine axes * Digital position display of the side rollers * Manual operation via JOY sticks - Two central rollers are driven directly via hydraulic motors - Conical rolling possible by tilting the rollers - Parallelism of the side rollers via torsion shafts - Bending on both sides - diameters of up to 1.1 times the top roller diameter are possible - Forged and hardened rollers with a hardness of 53-55 HRC - Low-maintenance, stable machine concept - Permanent lubrication of all bearings - Sturdy welded steel construction - electro-hydraulic hinged bearing for easy pipe removal - pressure gauge / pressure display for the rollers - Safety device (safety line with switch unit) - operating instructions * Special accessories included : - ROCCI height-adjustable center support * for large pipe diameters - ROCCI electro-motorized material feed table * motorized sheet feeding material support surface

Condition: used, Power source for orbital welding machine MESSER GRIESHEIM - POLYSOUDE PS204 Water cooling unit for orbital welding machine MESSER GRIESHEIM - POLYSOUDE RC200 Welding power source, inverter welding machine POLYSOUDE PS 204 + RC 200 Year of manufacture: 1997 Power source serial no.: 9885186 Cooling unit serial no.: 97861? Output: 200 amps = 20% duty cycle 90 amps = 100% duty cycle Power supply: 230 volts, 50 Hz, Schuko plug - Remote control cable type BP 1436 with 7.5 m connection cable - Adjustable output from 1 to 200 amps - DC only - HF ignition - Cooling water unit for torch cooling - 44,895 operating hours (read) - Operating and maintenance manual included Space requirements welding machine (L x W x H): 550 x 360 x 500 mm Space requirements cooling unit (L x W x H): 550 x 360 x 550 mm Weight welding machine: 45 kg Weight cooling unit: 25 kg Good condition Isdjt Awm Djpfx Af Ujat Sold without accessories The price refers to a set consisting of 1x power source and 1x water cooler.

Condition: used, Single-column hydraulic press, straightening press, punching frame ECKOLD Press frame with hydraulic cylinder, mobile press, punching unit Type RSD 1500 - 125 Machine. No. 317 / 690 Year of construction approx. 1986 Compressive force 150 ton. throat 125 mm ram stroke 35 mm Table size 280 x 210 mm Plunger surface Ø 125 mm Installation height (ram to table) max. 265 mm Table height above floor 403 mm Hydraulic operating pressure max. 500 bar - without hydraulic unit - Plunger surface with 4 M16 threads and 20 mm guide groove, central centering hole Ø 15 mm - 1 high-pressure hydraulic hose with external thread M30x1.5 mm, hose length 4 meters - 1 high-pressure hydraulic hose with union nut M30x1.5 mm, hose length 4 meters Space requirement L x W x H 700 x 300 x 1450 mm Ijdpfxjd Swtaj Af Usat Weight 1250 kg Good condition

Condition: used, Year of construction: 1993, Technical details: sheet width: 3050 mm plate thickness: 6,0 mm distance between columns: 3460 mm no. of strokes: min./max.: 9 / 17 Hub/min back gauge: 750 mm (motorisch) mm cutting angle: 0,5° - 3,0° ° cutting gap adjustment: manuell mm down holder: 18 Stück (hydraulisch) Stück Table dimensions: 380 x 3100 mm total connected load: 7,5 kW weight of the machine ca.: 4,56 t dimensions of machine: L: 3,64 x B: 2,55 x H: 1,58 m Equipment: With side stop L: 1000 × W: 100 × H: 60 mm and stop bar 990 mm, with 8 supports Operation via control panel and foot switch Cutting zone lighting Stroke counter Machine feet Iajdpfeu Rni Hsx Af Uot *

Condition: used, Rotary vane vacuum pump Two-stage Oil lubricated Iajdpfocu Tlpex Af Ust Manufacturer: Pfeiffer Type: DUO 250 Cat.-No.: PK D27 602 / K141 Status: Used (functional!) (A general overhaul is also offered) Suction capacity: approx. 250 m³/h final pressure: > 5x10e-3 mbar Warranty: 12 months (with general overhaul) Included: manual and oil Delivery time: ex works

Condition: used, Year of construction: 2002, fuel type: gas, Number of working hours 3184 h weight max. 8 t Iajdpswx R T Eefx Af Ujt weight of the machine ca. 13400 kg

Condition: like new (used), Year of construction: 2024, As-new polishing machine OPTIMUM OPTIpolish GZ40P with variable-speed conversion featuring Siemens inverter and cyclone extraction system. For polishing wheels with a diameter of up to 350mm, maximum wheel width 35mm, wheel bore 20mm. Suitable for continuous and intensive industrial use. Heavy-duty industrial polishing machine; its high dead weight absorbs the already minimal vibrations. Iaodpfjyglkyjx Af Uot Maintenance-free, long-life induction motor with smooth operation, cast iron housing. Additionally equipped with: Variable speed drive using Siemens Sinamics V20 inverter. Circumferential speed adjustable from 34 m/s down to 6 m/s. Sturdy base with cyclone extraction integrated in the base, thus requiring minimal space. Sound-insulated. The base must be filled with concrete by the customer. Automatic start/stop feature: When the external device is powered on or off, the extraction system automatically switches on or off with a 2-3 sec delay. There is no need to operate the extraction system separately. According to hazardous substance regulations, residual dust is extracted after the machine shuts down. The machine is located at 71334 Waiblingen-Beinstein and can, of course, be inspected by appointment. Please contact us for further information.