Ergotech - system 250/280-80

DEMAG

Condition: ready for operation (used), Year of construction: 2005, clamping force: 5,000 kN, screw diameter: 70 mm, injection weight: 1,230 g, This 3-axis DEMAG Erdotech 500-3300 hydraulic injection moulding machine was manufactured in 2005. It features a screw diameter of 70 mm and a shot weight of 1,230 g. The machine has a maximum daylight of 1,450 mm and includes a handling system with a Wittmann linear robot. If you are looking to get high-quality injection moulding capabilities, consider the DEMAG Erdotech 500-3300 machine we have for sale. Contact us for further details. • Distance between tie bars: 900 mm • Min. mould installation height: 400 mm Hjdpsyycu Defx Abwjk • Max. daylight (distance between platens): 1,450 mm • Centering ring: 160 mm • Core pull: 2-circuit core pull control (plus 1 extra core pull mentioned) • Control system: Demag NC4 Additional equipment • Handling unit: Wittmann linear robot, 3 axes (X/Y/Z linear) • Granule feeder: Wittmann, Typ VITMAX A312-Y (24 V, 1 A) • Hot runner controller: Gammaflux, Typ GM1G030F012S4EJ

Condition: good (used), Crane remote control, crane control, crane control, pendant control, control switch, control cylinder -Manufacturer: Demag, control switch for crane remote control with cable Hodpfx Ajxzqp Aobwsk -Type: DST 6 -Connector: 16-pin -Crane remote control: 2 steps below the switch each -Transport dimensions: 870/360/H140 mm -Weight: 6.1 kg

Condition: used, Crane remote control, crane control, crane control, pendant control, control switch, control cylinder Hedpfxjxzq Sqj Abwok -Handover: in its current condition as seen, see photos -Condition: the switching elements are missing -Manufacturer: Demag, control switch for crane remote control with cable -Type: DSE -Connector: 16-pin -Transport dimensions: 600/330/H140 mm -Weight: 3.5 kg

Condition: used, Low-priced from company liquidation Hodpfx Asyyarmobwek

Condition: ready for operation (used), Year of construction: 2001, clamping force: 3,500 kN, screw diameter: 70 mm, injection weight: 800 g, This 3-axis DEMAG Ergotech 350/710-2300 was manufactured in 2001. It features a screw diameter of 70 mm and a maximum daylight of 1,080 mm. The machine includes a handling system with a Wittmann Linear Robot and a granule feeder. If you are looking to get high-quality injection moulding capabilities, consider the DEMAG Ergotech 350/710-2300 hydraulic injection moulding machine we have for sale. Contact us for further details. • Distance between tie bars: 710 mm • Min. mould installation height: 330 mm • Max. daylight (distance between platens): 1,080 mm • Centering ring: 160 mm • Core pull: 2-circuit core pull control (+1 extra core pull mentioned) • Control system: Demag NC4 Additional equipment • Handling unit: Wittmann linear robot Hodpoyx Unajfx Abwsk • Granule feeder: Wittmann VITMAX A308 DPV-40 (24 V, 1 A, 11.5 kW), year 2008

Condition: excellent (used), Year of construction: 2015, clamping force: 1,000 kN, Clamping force: 100 t Hedpjx Tdp Nefx Abwjk Opening max: 500 mm Mould heigh: 250 mm Platen size: 590x600mm Distance between tie bars V: 420 mm Distance between tie bars H: 420 mm Type: Horizontal Drive: Hydraulic Screw diameter: 30 mm Injection weight: 103 g Injection volume: 115 cm3 Injection pressure: 2755 extra equipment: 1. 2 hydraulic core pull circuits on moving platen (proportional valves) 2. Additional connections for 2 core pulls on fixed platen 3. Pneumatic core pull (2 circuits) on moving platen 4. 4-zone cooling water flow controller with temperature display 5. Compressed air blow valves on fixed and moving platens (programmable) 6. Integrated hot runner control, 8 zones 7. Interfaces for external nozzle heating bands 8. Interface for integrated temperature control units (up to 6 circuits) 9. Interface for mould temperature monitoring (2 circuits) 10. EUROMAP 67 for automation equipment

Condition: ready for operation (used), Bridge Crane 5t, Demag Bridge Crane 5t, Crane 5t, Used Machine Manufacturer: Demag Overall dimensions: 10,700 x 3,000 mm Electrical data: 400 V; 50 Hz, total current = 18 Amps Hoisting unit: Demag P35 Load capacity: 5,000 kg / 5t Rope length / lifting height: 8 m - Wired remote control - Crane travel motor refurbished - Trolley motor refurbished Hodpfx Abswd Hhcewjk

Year of construction: 1999, condition: ready for operation (used), Hydraulic injection moulding machine manufactured in 1999. This DEMAG Ergotech 150-610 Viva features a screw diameter of 45 mm and a maximum daylight between platens of 850 mm. It has a shot weight of 260 g and a maximum mold installation height of 250 mm. If you are looking to get high-quality injection moulding capabilities, consider the DEMAG Ergotech 150-610 Viva machine we have for sale. Contact us for further details. Hjdpfx Abeyxrt Tewjk

Condition: used, Year of construction: 1978, Technical details: lifting capacity: 0,25 t height lower edge cantilever arm: 3450 mm cantilever arm length from center column: 3000 mm column diameter: 194 mm rotation: ca. 100 ° There are 3 column-mounted slewing cranes available for sale from Leipzig. ( price per piece) 2 column-mounted slewing jib cranes (No. 3 and No. 4) refurbished and 1 column-mounted slewing jib crane (No. 5) as is/is, without refurbishment. Demag-PK2 N-F hoist, 250kg lifting speed 10 m/min; fine lift 2.5 m/min. Load chain single chain; see type plate; control via pendant control, mobile manual Hsdpfx Aou Szhpebwjk at column base no. 3 and no. 5 is foot plate with 580 x 580 x 20 mm and at no. 4 foot plate 400 x 400 mm beam Column i.D. *

Condition: used, Demag Ergocontrol IBED NC4- removed from Demag Ergotech El-Exis S 60/370-310 - removed from running machine Hsdpjyxg Swefx Abwjk - 1 cover missing - no effect on functionality - fully functionalmanufacturer: Demag type: NC4 spare part no.: 89380065 manufacturer no.: DIf the spare part is traded in an exchange procedure, a partial credit note will be issued after receipt of the defective part and inspection by the manufacturer. We reserve the right to refuse a credit note based on the condition or age of the returned part. The defective part must be in a repairable condition; the credit note will be issued after feedback from the manufacturer.