Edge banding

Brandt Optimat KDN 330

Condition: used, Year of construction: 2004, Used machine Year of manufacture: 2004 with gluing unit for hot-melt adhesive granules Glue reservoir located below the glue roller Glue application to the workpiece via glue roller in both co-rotating and counter-rotating modes automatic edge magazine for coil material and fixed lengths Pressure zone with pneumatically-driven main pressure roller and special post-pressure rollers to compact the upper and lower glue joint Centrally adjustable upper pressure Central manual chain conveyor lubrication Control panel at machine infeed End trimming unit (saw aggregates) for front and rear edge overhang with high-precision linear guides 2 motors, each 0.18 kW Swivel range for straight and bevel cutting 0–15 degrees Flush-milling unit, top and bottom, with vertical and horizontal tracing Swivel range 0–15 degrees with 2 milling motors, each with replaceable insert cutter combinations (straight/radius) Digital counters enable rapid and precise, i.e., repeatable, settings Gtedpfx Agsxya Rto Sot Two-point pneumatic adjustment for upper and lower milling motors Scraper unit for finishing processing with horizontal/vertical tracing Support table extendable up to 350 mm Integrated section control for contactless operation of processing functions. Settings via keyboard and LED display Workpiece thickness: 8–50 mm Edge thickness: 0.4–3 mm Feed speed: approx. 9 m/min Connected load: 4.1 kW Compressed air connection: 6 bar Weight: approx. 750 kg Machine length: 3,150 mm Availability: short term Location: Flörsheim

Condition: used, Year of construction: 1997, - edge banding unit Gtedpfxsd Inkte Ag Sst - Cross-cutting unit - Milling unit - Fine trimming unit - scraper - buffing unit

Condition: good (used), overall weight: 5,000 kg, working width: 1,300 mm, plate width: 1,350 mm, Veneer Press Bürkle U140 Working surfaces: 5 pcs. Intermediate plates: 4 pcs. Plate dimensions: 3050 x 1350 mm Working dimensions: 3000 x 1300 mm 8 hydraulic cylinders Max. surface pressure: 5 kp/cm2 Gtodpfexn Um Esx Ag Set Max. operating pressure: 348 bar Heating medium – hot water from central heating Cooling – cooling circuit with WILO pump, expansion tank, piping Weight approx. 5000 kg Good technical condition of plates and hydraulics

Condition: ready for operation (used), Year of construction: 2005, functionality: fully functional, Single-sided edge banding machine Gtodpfx Aoxl Ufveg Set Manufacturer: Brandt Model: KDF 660 Year of manufacture: 2005 Max. edge thickness: approx. 12 mm Max. workpiece thickness: 60 mm Max. coil material thickness: 3 mm Equipped with: - Pre-milling unit - Coil magazine - Glue application unit - End trimming unit - Top/bottom flush and radius milling - Top/bottom radius milling with front/rear edge copying - Radius scraper - Buffing station Feed speed max. approx. 16 m/min. Connection: 400 V, 50 Hz, 3 Ph Total connected load: approx. 15 kW

Condition: used, Year of construction: 2018, Used machine Year of manufacture: 2018 Special feature: Machine for up to 100 mm edge height! Condition: Factory-inspected by Lange Maschinenbau Equipment and technical data: - Machine table with 13 running rollers for improved workpiece guidance - Edge feeding, synchronous with belt feed - Edge thickness adjustable via digital counter - Pneumatic roller separation with knife (for cuttable edges) - Three pressure rollers - Belt feed: - 0.25 kW - approx. 1250 mm long - approx. 6.0 m/min - 50 mm wide toothed belt with thick, workpiece-friendly rubber top - Digital counter for height adjustment - Direct glue application to the workpiece: drip-proof glue pot with glue supply from below and rapid heat-up time after standstill - Flush cutting unit: - for front and rear workpiece edges - automatic sensing at the workpiece - pneumatic cutting with knife for cuttable edges - Flush trimming unit - with vertical sensing and horizontal guidance - reproducible setting using digital counters - 2 powerful 0.4 kW high-frequency motors - stepless speed adjustment from 4000 to 18000 rpm - Cutter Ø 70 mm, Z4, radius 2 mm/15° - central extraction nozzle Ø 100 mm - 2 chip extraction hoods with hose Ø 60 mm - Automatic height adjustment of the upper cutter with belt feed - Continuous workpiece support approx. 1800 mm long - Workpiece support rail, extendable by approx. 300 mm - Rotatable foil dispenser Ø: 800 mm - Workpiece width: min. approx. 80 mm - Workpiece thickness: 10 – 100 mm - Workpiece length: min. approx. 220 mm - Edge thickness: 0.4 – 2.0 mm - Roller separation: max. 1.0 x 55 mm, 2 x 45 mm - Glue pot heating capacity: 2.7 kW - Heat-up time: approx. 10 minutes - Working height: approx. 880 mm - Electrical connection: 400V, 50 Hz, 3Ph + N - Total connected load: 3.8 kW - Pneumatic connection: 6 Bar Dimensions (without foil dispenser): approx. 1800 x 700 x 1300 mm Weight: approx. 260 kg Gtjdpfxjwka S Is Ag Set Availability: short-term Location: Flörsheim

Condition: used, Year of construction: 2017, Used machine Year of manufacture: 2017 Equipment and technical specifications: Factory-refurbished by Lange Maschinenbau Minimum workpiece width: approx. 75 mm Workpiece thickness: 8 - 50 mm Minimum workpiece length: approx. 120 mm / 180 mm for corner copying Edge thickness: 0.4 - 2 mm Jointing unit shaving removal: 0 - 2.0 mm, infinitely adjustable Jointing unit with 2 counter-rotating, application-controlled jointing motors Diamond tooling height = 55 mm Direct glue application to the workpiece Glue pot with 1.5 kg capacity EVA/PUR glue pot with discharge function Pressure unit End trimming unit with high-frequency motor, 2 saw blades and high-precision linear guides Combined milling station for radius and bevel milling Corner copying unit Flush trimming unit Gtodow Sbbljpfx Ag Sot Extraction pipe system with 90° bend and manual slide valve mounted on the machine Machine length: 3273 mm Dimensions: 320x110x200 Availability: short-term Location: Flörsheim

Condition: good (used), Year of construction: 2006, functionality: fully functional, machine/vehicle number: 288, I am selling a Cehisa SYSTEM 4 edge bander, manufactured in 2006, first owner. Excellent condition. Technical parameters in the attachment. Gsdpfxov Hc Dge Ag Sstt

Condition: used, Year of construction: 2016, Used machine Year of manufacture: 2016 Condition: Currently still in production Gtedpfxsw Rtade Ag Sjt Equipment and technical data: Glue pot Pressure zone Cut-off saw Combination milling (radius 2 mm), flush trimming Workpiece thickness: 8 - 50 mm Minimum workpiece width: approx. 75 mm Minimum workpiece length: approx. 120 mm Edge thickness: 0.4 - 3.0/5.0 mm Maximum edge height = workpiece height + 4 mm (2+2) Electrical connection: 400V, 50 Hz, 3-phase Total connected load: 3.2 kW Feed speed: 8.0 m/min Pneumatic connection: 6 bar Net weight: 550 kg Optional retrofits for the machine: Radius scraper Flat scraper Buffing unit Location: NRW Availability: Approx. December 2025

Condition: used, Year of construction: 1970, Year of manufacture: 1970 Total pressing force at 320 atü: 80 tons Pressing cylinder: 6 pistons Motor power: 1.1 kW Heating-up time approx. 20 min. Price ex works. Gtjdpfx Agswx Rrnj Set

Condition: excellent (used), Year of construction: 2000, I sell the format sliding table saw with scoring SCM SI 300N, year 2000. Sliding table length 3200mm. Max. cutting width on cross fence 1950 / 2850mm. Max. cutting width on parallel fence 1270mm. Motor 5,5 kW. Max. saw blade diameter fi.300x30mm Max. scoring saw blade diameter fi.120x20mm Main blade (scoring blade) 4000 (8000) rpm. Condition very good. Avialable immediately. Please contact for more photos and details. Gtodpfx Asiu Awbjg Sot