Condition: used, Number of sanding units 2 st. sanding width 190 mm Sanding height max. 4-150 mm Hess Junior single wood sander ----- basic structure: Stable, heavy welded construction made of thick-walled rectangular hollow profiles with additional, statically calculated bracing for optimal vibration damping. Staggered grinding units with large dimensioned Belt drive drums for slip-free belt travel. Two-point suction for direct and airborne dust extraction with integrated blow-off device. grinding units in heavy steel plate construction as the basis for vibration-damped, quiet belt run. All guides as a ball linear set on hardened and polished waves. Lasting precision thanks to protection against dust and dirt of the sphere linear sets. Contact roller and sanding pad in a balanced ratio to the grinding belt grain load. The large dimensioned drive drums guarantee the full transmission of the 5.5 kW drive power of the grinding motors on the grinding belt. This means the strongest chip removal possible. Automatic machine stop triggering if the tape breaks. Optical display on control panel. Sanding shoe for finish made of special material with optimal Heat dissipation and additional sliding lining. Easy to use pad change. Abrasive belt tension over appropriately dimensioned compression springs. Sanding belt relaxation for belt change by means of pneumatic Device for sensitive, distortion-free loading of new tapes. Upper Grinding unit and brush device (additional equipment) centrally motorized adjustable. Timber guide in the entry area for hard guide and guide rails supported on both sides pinch rollers. Tilt-proof transport of profiled workpieces calibrated conveyor belts with continuously adjustable feed rate. Automatic machine stop triggering by wood thickness control device. Optical display of the control panel. Infeed table via fine, precise threaded spindle for lower Grinding chip removal manually adjustable via scale (resolution 0.1 mm). The length Column table guidance guarantees an absolute parallel adjustment. The Adjustment of the flight circle to the outfeed table is achieved by adjusting the height of the lower one Grinding unit via precise threaded spindle and scale display (resolution 0.1 mm) accomplished. Clear, user-friendly arrangement of all electrical functional, operating and display elements on the front of the machine: grinding unit below, Grinding unit above, workpiece transport device, Grinding thickness setting, brushing device above/below, belt utilization, Operating display, fault display. All motors are against overload electrically secured. Dkjlnjt Tqyls T Hypel Technical specifications : ----- Sanding belt speed: 25 m/sec. Grinding width: 190 mm Grinding thickness: 4 - 150 mm Shortest workpiece length: 280 mm Feed speed, continuously adjustable 5 - 25 m/min. Sanding belt dimensions: 200 mm width, 1850 mm length Electrical equipment according to VDE Electrical connection : 400 V., 3/N, 50 Hz. Pneumatic connection: R 3/8", 6 bar, 80 NL grinding units: 2 x 5.5 kW feed: 0.75 kW height adjustment : 0.18 kW Pneumatic connection: R 3/8", 80 NL, min. 6 bar, max. 8 bar Extraction air quantity: 2 x 2000 to 2500 m3/h 20 - 25 m/sec. Extraction connection piece: 2 x 180 mm dia, on top of the machine housing External dimensions: without control cabinet 1750 mm wide, 1850 mm high, 1000 m...

Condition: used, Year of construction: 1993, ANGULAR PROFILING MACHINING CENTER Brand: SAC Model: P4 Serial number: 9304 Dksln Terx Tcgs Hypsl Year: 1993 Model: F5 Serial number: 93030 Year: 1993 Machines visible in our workshops CHARACTERISTICS : - Cutter rotation speed: 6000 rpm

Year of construction: 1986, Condition: excellent (used), I sell Profile Grinding Machine Reckmann LM 161. Grinder in very good condition, little used. Dkeln Teuyg Rns Hypol

Condition: good (used), working width 230mm working height 120mm Dkeln T Hyevtt Ayepel spindle diameter 40mm 4 heads + unit for cutting glazing bead control from ATS panel head adjustment in two axes electric adjustment of the pressure beam smooth adjustment of feed speed The machine worked in line with other machines.

Condition: good (used), Gold / Stehle / Fantacci / Leitz Dkoln T Hsixtudjypjl house window - tool used different type, on request

Condition: used, Leitz HM - IV 66 window set with faceplate and front door set. Sold in "as is" condition, tool has not been resharpened, ex location Seevetal, without transport, subject to prior sale, Doln Tehzgy Nj Hypskl

Condition: refurbished (used), Functionality: fully functional, SCM four-sided planer, Model Compact 22 4 spindles Dolnsvuk Ags T Hypekl Electro thickness lifting Traction roller speed variator Input traction roller 23 cm working width 12 cm working height The machine is in excellent condition

Condition: excellent (used), Year of construction: 2015, Functionality: fully functional, overall weight: 1,050 kg, MEK wooden windows sash processing center The device was used for processing MEK windows (fixed wooden windows). This production device has an automatic optimization (6000 mm long workpiece is cut and end connections are made according to the program) The device is also equipped with a labelmaker Device is in good condition. The price of the device is to be offered by the buyer. Buyer is responsible for transportation and dismantling. Doln T Hyju E St Sepskl If you have any further questions, please contact us about the production equipmen

Condition: excellent (used), Roller conveyors in lengths 5000 +6000 mm width 600mm with felt or oil tracks for laying. several times available! Please request Dkolsmt D Rasn T Hypjl

Condition: excellent (used), 3 motors with 0.37 kW each Roll width 13.5 cm Working area 220 x 98 cm Dkeln Tst Ama He Hypsl Overall dimensions 141 x 132 cm 2 working fish Adjustable roller speed

Year of construction: 2014, Condition: used, PROLOGIC window construction software FenOffice 14 Dkeln T Horci S Seypjl Conturex

Year of construction: 1998, Condition: excellent (used), I sell the window tenoning profiling centre Weinig Unitec 10 Year 1998. Moulding heads OERTLI. Available immediately. Unit price 8.500 euro. 3 pcs. available. Condition very good ! Dkjlnjfzzhko T Hypel

Condition: used, Year of construction: 2001, Functionality: unexamined, spindle stroke: 40 mm, Weinig Unicontrol 10 window production line Dkoln Tsu A Ixfe Hypsl

Condition: excellent (used), Year of construction: 2011, Functionality: fully functional, machine/vehicle number: W 115375, We are selling a Conturex 2 C 124 for milling, drilling and profiling work - special window construction machine. Previously used for the production of playground equipment. Workpiece length 250 - 6000 mm Dsln T Hot Ira Ajypekl Workpiece width 40 x 250 mm Workpiece height 20 - 150 mm 1 x 4-axis main spindle 20 kW; 1 x 5-axis universal spindle 24 kW 2 x 24-position tool changer Axis-controlled part insertion with insertion table Precise workpiece measurement with barcode reader Automatic workpiece transfer from Power-Grip clamp table 1 to clamp table 2 Adjustment speeds: X-axis 110 m/min, Y-axis 120 m/min, Z-axis 60 m/min Automatic outfeed and unloading of workpieces Very well maintained and well cared for machine

Condition: excellent (used), Roller conveyor with roller bars in the plant section, type RU-RD 30, length approx. 3000 mm, turning device 360°, locking device of the turning device, movable on rails, rollers 8 x 70 mm = 580 mm deep multiple available! Dkjln T Hyemt D Ifepjl

Condition: excellent (used), Motor 7.5 kW 2 kW 0.37 kw Saw 450mm 30mm Spindle height 42cm The horizontal working width of the saw is 15 cm Electric feed Dsln Tsurt Hfo Hypokl Table width 32 m Pneumatic pressure

Condition: excellent (used), Tool OERTLI for SCM WINDOR Deln T Hyehmpn Hepokl IV 70 MM wooden window IV 95 MM wooden window Wood Alu 70 MM More pictures/ sketch on request

Year of construction: 1997, Condition: excellent (used), I sell the complete window profile production line: 1pc. 5-spindle fourside moulder with saw aggregate Weinig Unimat 23EL. - without HESS sanding machine - another machine for change available on agreement 2pcs. tenoning profiling centre Weinig Unitec 10 2pcs. profiling automat centre Weinig Univar 10 1pc. CNC drilling machine KOCH WinDoor - set of complete Weinig automation feeders and conveyors Year 1997. Profile heads OERTLI. Available immediately. Uninstalled and loaded on original Pallets. Deln Tefzzide Hypskl Condition very good !

Condition: excellent (used), Year of construction: 2011, Functionality: fully functional, Unicontrol 12 Consisting of: Cut-off unit (item A), Tenon and slotted spindle (item C), Transfer belt (Pos. I), profiling spindle (Pos L), profiling spindle (Pos. N), Profile shaving unit vertical right (Pos. P) For the production of individual parts and elements in frame-by-frame or serial production. Consisting of a cross processing unit and a longitudinal processing unit connected to a transfer belt. Working width 40-140mm (See pressure ruler left 40 - 140 mm) Working height 40-120mm Workpiece length min. approx. 275 mm + 1 x end profile length Long machining: approx. 220 mm + 2 x end profile length Workpiece length max. 3500 mm The part dimensions depend on the machine equipment, production type and tool assignment. A final definition of the part dimensions is only possible after receipt, inspection and approval of the complete and final layout drawings. Cross machining: Table feed Motor power 0.3 kW (0.4 HP) Pre-set feed speed for cutting, profiling and return 3-25 m/min Doln T Hsumci Seypokl Vario table with (studio window production possible) The clamping length of all tenoning and slotting spindles can be used without a tool blank. Workpiece clamping by means of a clamping bridge. Operated by a clamping cylinder installed under the table. NC-controlled long fence mounted on the slotting table. Studio window device Swivel angle max. +/- 75° The minimum workpiece length for slanted windows depends on the angle and the width of the wood. Possible part dimensions for slanted window production Angle Max. Min. Working width Workpiece length +/-75° 80 mm 800 mm +/-70° 120 mm 490 mm +/-60° 240 mm 360 mm +/-90° 350 mm 185 mm For angles greater than 60° only counter processing Commission not documented 1)NC automatic angle adjustment for machining angled parts Splinter protection by means of overtravel counter Over the entire spindle length of the tenoning and slotting spindle for 90° machining Manually trackable counter-rail for angled part machining 2) Additional counter-rails

Condition: used, Year of construction: 1991, CNC Machining Center weinig UNICONTROL 10 Location Gorzów Wlkp. Conditions of delivery OWN RECEIVING Cost of delivery to be negotiated Startup type to be negotiated Description Comments Dkeln Tjdm Umls Hypsl Longitudinal saw: 2800 rpm min., 3 kW, power take-off and slot spindle: 5 x 100 mm, 11 kW, 2.800 rpm. min., 1 spindle profiling: 6000 rpm. min., 11 kW, 2. Spindle profiling: 6000 rpm. min, 11 kW. "Angle windows, machining center WEINIG UNICONTROL 10 Number of spindle spindles: 1 Number of spindles molding: 2 Length of the spindle spindle mm: 300 Xrwk8iolx Length of profiled spindle mm: 295 Separate shaft grooves: yes Continuous stroke mm: 100 Spindle diameter mm: 50 Cutting tool cutting wheel mm: 232 Cutting wheel for perforation mm tool: 360 Length of material max mm: 2,600 Equipped for profiling: yes Automatic kontherholz: yes Glaucoma: Yes Workpiece rotation: Roller transport Main engine power kW: 11 Max feed rate m / min: 8 Control: Spindle ON / OFF only Working condition: dismantled / stored "

Year of construction: 1998, Condition: excellent (used), I sell the window profiling automat centre Weinig Univar 10 Djln T Hsfzzhrsypokl Year 1998. Moulding heads OERTLI. Available immediately. Unit price 8.500 euro. 4 pcs. available. Condition very good !

Condition: good (used), Year of construction: 1990, I sell the combined tenonging machine with drilling head BALESTRINI I2F 1 tilting table with pneumatic material pressure. Automatic cutting saw from bottom. Tenoning milling head able to do the finger-joint as well. Dsln T Hyohw Dfnspokl Drilling head for dowel holes production 3 spindles. Revolving 360° enabling any position. Feeding automatic. Positioning on end-sensors. Available immediately.

Year of construction: 2005, Condition: excellent (used), I sell the window angular centre Colombo Angelo Figli AM33/AF. Year 2005. Tenoning side saw blade + 620mm spindle fully servomotorical. Deloh Txkqen T Hypjkl Profiling side 3 spindles + glass-strip cut aggregate fully servomotorical. Moulding heads VYDONA WOOD EU78-92. Wood-Alu 92, all programmed in the machine and included / possible to count out when you dont buy them. Total power 50KW Total weight 6000kg. Compact dimension, suitable also for small workshops. Available immediately on stock. Very good condition. Complete set with tools / possible to count out when you dont buy them. Please contact me for more photos and information.

Year of construction: 2000, Condition: excellent (used), I sell the window angular centre SCM Multiflex. Moulding heads VIVALDI EU68mm. Cutting + Tenoning spinde right side / Tenoning side. 2 pcs. Profiling spindles + glass strip cutting machine left / Profiling side. Available immediately. Dkolnehw Dfyj T Hypjl

Year of construction: 1998, Condition: excellent (used), I sell the window production set: 1pc. tenoning profiling centre Weinig Unitec 10 1pc. profiling automat centre Weinig Univar 10 Year 1998. Moulding heads OERTLI. Available immediately. Total price 17.000 euro. Condition very good ! Dkolnofzzhyo T Hypjl