Used Sanding machines for sale (11)

Condition: used, Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Noljt Tqy Eshcdw Iecr Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Condition: good (used), Functionality: fully functional, Double-sided grinding machine / grinding machine top/bottom Manufacturer Löwer Type DSM 3000 with workpiece return Nolhcdjv Auf Iow Iocr Working width: 290 mm Grinding thickness: 2-200 mm Shortest workpiece length: approx. 320 mm Equipped with: 1x grinding unit from above, 7.5 kW 1x brushing unit from above, 0.37 kW 1x grinding unit from below, 7.5 kW 1x brushing unit from below, 0.37 kW Grinding belt dimensions: 300 x 1800 mm Electric height adjustment, 0.37 kW Adjustable feed, 6/11/16 m/min. Compressed air: 6-8 bar Dimensions approx. 2700 x 1100 x 1900 mm Weight approx. 1600 kg

Year of construction: 1986, Condition: excellent (used), I sell Profile Grinding Machine Reckmann LM 161. Grinder in very good condition, little used. Ncslhcdouyg Rnjw Isr

Condition: excellent (used), 3 motors with 0.37 kW each Roll width 13.5 cm Ncelot Ama Hohcdw Ier Working area 220 x 98 cm Overall dimensions 141 x 132 cm 2 working fish Adjustable roller speed

Condition: used, Number of sanding units 2 st. sanding width 190 mm Sanding height max. 4-180 mm Ncolsv D Rg Djhcdw Ijr HESS - GLORIA 2 BELT SINGLE WOOD SANDING MACHINE ----- Machine is being checked! Manufacturer's description: ----- Compact design designed according to modern principles. Quiet and vibration-free operation thanks to rigid, stable machine housing and special insulation. Work safety device in accordance with the EC Machinery Directive with the "dust-tested" certificate. Offset grinding units with large-dimensioned tension rollers for good heat dissipation and stable sanding belt guidance. Sanding units with forced sanding belt oscillation. 2-point sanding dust extraction directly on the sanding roller. Airborne dust extraction on the large tension rollers. Integrated sanding belt blower for longer service life of the sanding belts. Integrated brushing and finishing device, adjustable via threaded spindle, with large dust extraction. Motorized grinding thickness adjustment of the entire upper unit via precision threaded spindles and linear ball sets on hardened and ground precision shafts with dust and dirt protection. Electronic digital display for workpiece thickness (resolution 0.1 mm). Contact roller and grinding shoe in a balanced ratio to the grinding belt grain load. Hardened and ground grinding rollers. Maintenance-free and wear-free oxide ceramic grinding shoes (DBGM) with excellent sliding properties, good heat dissipation and high dimensional accuracy. Grinding belt tension via pneumatic cylinder. Grinding belt change via pneumatically controlled belt relaxation. Ability to adjust the grinding belt run when changing the belt. Electro-pneumatic pressure monitoring of the compressed air supply with visual fault display. Automatic machine stop triggered when sanding belt breaks and by run-in protection with integrated wood thickness control. Optical display on the control panel. Feed device and proven, calibrated non-slip and non-adhesive transport belts on precisely ground tables and spring-loaded pressure rollers. Cardan shaft drive for even wood transport. Feed speed continuously adjustable. Chip removal adjustment bottom via precision threaded spindle with dimension display via scale ring (resolution 0.1 mm) Ergonomic arrangement of the operating and setting elements on the machine front: sanding unit and brush device at the top, sanding unit and brush device at the bottom, workpiece transport device, sanding thickness setting, operating display, fault display. Control and operating unit with lockable main switch built into the machine housing. All motors electrically protected against overload. Technical data: ----- Grinding belt speed: 24 m/sec. Grinding width: 190 mm Grinding thickness: 4 - 180 mm Shortest workpiece length: 300 mm Feed speed: Continuously adjustable 5 - 25 m/min. Sanding belt dimensions: 200 mm wide 1600 mm long Electrical connection: 400 V, 3/N PE, 50 HZ Grinding units: 2 x 4 kW Feed: 0.75 kW Height adjustment: 0.18 kW Pneumatic connection: R 3/8", 80 NL, 8 bar Extraction air volume: 2 x 2000 - 2500 m3/h 20 - 25 m/sec. Extraction connection nozzle: 2 x 160 mm diameter at the top of the machine housing External dimensions: Length: 1600 mm Width: 1030 mm Height: 1820 mm Height with extraction...

Condition: new, Number of sanding units 2 St. sanding width 190 mm Sanding height max. 2-180 mm LÖWER double-sided grinding machine DSM 2000 ----- Double-sided single wood sander for sanding Solid wood such as window wood etc. Stable top quality Guide with long casting tables, brushing and finishing equipment and conveyor belt feed. Suitable for high continuous loads even with higher chip removals. - Staggered sanding and finishing units at the top and bottom - Directly driven rubberized grinding rollers for slip-free power transmission - Combined grinding via roller and shoe for high chip removal at the same time flat intervention zone - Maintenance and wear-free CERMET-coated sanding shoes with very good thermal conductivity and absolute Dimensional accuracy - External cooling of the grinding zones for cooler grinding and higher grinding Grinding belt service life - Forced pneumatically controlled sanding belt oscillation - effective sanding dust extraction directly on the sanding rollers Airborne dust extraction on the tension rollers - Integrated brushing and finishing device with large sanding dust extraction - Motorized grinding thickness adjustment via precision threaded spindles and large-sized linear ball bearing sets on hardened and ground precision shafts with dust and dirt protection - Adjustment of the chip removal at the bottom using a precision threaded spindle Dimension display via scale ring (resolution 0.1mm) - Sanding belt tension via pneumatic cylinders with constant clamping pressure - Sanding belt change with pneumatic belt relaxation in seconds - Adjustment of the sanding belt run when changing the belt - electro-pneumatic compressed air monitoring - Run-in protection via contact roller for workpieces that are too thick - Workpiece transport via calibrated non-slip and non-stick conveyor belts over heavy, 1000mm long cast tables with a finely planed surface and Spring-loaded pressure rollers with fine adjustment - Cardan shaft drive for smooth and even workpiece transport - Feed gear motor with three different feed speeds for quick adaptation to different types of wood - all motors electrically protected - Ergonomically arranged controls on the workpiece inlet side - automatic workpiece thickness scanning (no previous measurement necessary) - Digital thickness display (resolution 0.1mm) with modern magnetic tape system Technical data: - Sanding belt speed: 22 m/s - Sanding belt length: 1800mm - Sanding belt width: 200mm - Working width: 190mm - Grinding thickness: 2-180mm Njlhjvu Hdtocdw Iocr - two brake motors for drive: 5.5 kW - Feed motor: 1.0 kW - Feed speed: 6, 11 and 16 m/min. - automatic height adjustment: 0.37 kW - two brush units with fiber brushes D 120 x 200mm at 0.37 kW - Suction nozzle: 2 x 120mm and 2 x 150mm - Pneumatic connection 6 bar - Working height: 850mm - Length: 2105mm - Length with control panel 2490mm - Width: 880mm - Height: 1910mm - Weight: approx. 1500 kg - Operating voltage: 400 volts, 50 Hz, 3P - CE version ----- ----- Basic price of the machine on request! ----- ----- Special accessories with surcharge: continuous feed 4-20 m/min. for speed adjustment to the previous machine Price on request Workpiece blow-off - using nozzles from above and below at the machine ...

Condition: used, Number of sanding units 4 St. sanding width 190 mm Sanding height max. 180 mm Control ja weight 3300 kg Dimensions (L/W/H) 2600x920x1890 mm Dust suction hood 2x180, 2x120 mm Double sided grinding machine Löwer DSM 2004 Double-sided four-band single-wood sanding machine for sanding Solid wood, e.g. Window wood etc. Highly stable top model with innovative details. Suitable for high Continuous load even at higher chip removal rates. - Successively arranged grinding units for rough grinding, fine grinding and finish sanding, each from above and below 1. Belt sanding unit with heavy steel roller 2. Belt sanding unit with rubberised roller and shoe 3.Finish aggregate with fiber brush - Direct driven wheels for slip-free power transmission - Maintenance and wear-free CERMET-coated sanding shoes with very good thermal conductivity and absolute dimensional accuracy - Foreign cooling of the grinding zones for a cooler grinding and higher Sanding belt life - positively driven pneumatically controlled grinding belt oscillation - effective sanding dust extraction directly on the sanding rollers - Dust extraction on the tension rollers - integrated brushing and finishing device with large sanding dust extraction - Motorized grinding thickness adjustment via precision threaded spindles and large dimensioned linear ball bearing sets on hardened and ground precision shafts with dust and dirt protection - Adjustment of chip removal below via precision threaded spindle with dimension display via scale ring (resolution 0,1mm) - Grinding belt tension via pneumatic cylinder with constant clamping pressure - Abrasive belt change with pneumatic belt release in seconds - Adjustment of the grinding belt when changing the belt - Electropneumatic compressed air monitoring - Overflow protection via contact roller for workpieces that are too thick - Workpiece transport via calibrated non-slip and adhesive conveyor belts Nolhevu Hgbocdw Ijcr over heavy, cast tables with finely planed surface and sprung Pinch rollers with fine adjustment - Cardan shaft drive for jerk-free and uniform workpiece transport - Feed gear motor with stepless speed 4-20 m / min - all motors are electrically protected - ergonomically arranged controls - digital strength display (resolution 0.1mm) with modern magnetic tape system Technical specifications: - Sanding belt speed 22 m / s - Sanding belt length 1800mm - Sanding belt width 200mm - Working width 190mm - Abrasive thickness 2-180mm - four brake motors for drive 5.5 kW - Feed motor 1.5 kW - Feed rate 4-20 m / min. - automatic height adjustment 0.37 kW - two brush sets with fiber brushes D 120 x 200mm à 0.37 kW - Exhaust nozzle 2 x 180mm 2 x 120mm - Extraction air speed 20 m / s - Pneumatic connection 6 bar - Working height 870mm - Length (with Softdisc 2740mm) 2600mm - Length with control panel (with Softdisc 3035mm) 2985mm - width 880mm - height 1910mm - Weight about 3300 kg - Operating voltage 400 volts, 50 Hz, 3P - CE version Equipped with the following options: - Sanding belt blow 4-band via nozzles directly at the radii of the tensioning rollers within the extraction system arranged, separately switchable - Disc unit for defibering - two grinding disc discs with 200 mm diameter (maximum grinding width 180 mm) - adjustable laterally and in delivery - including frequency converter for stepless speed regulation instead ...

Condition: new, Number of sanding units 8 st. sanding width 180 (260) mm Sanding height max. 160 mm Dimensions (L/W/H) 3065x1600x1900 mm weight of the machine ca. 1500 kg LÖWER Leistomat SD ----- Automatic fine grinding machine for wood grinding (smoothing, defibering and Edge breaking) or intermediate sanding of profiled window bars. With soft disc Technology for the visible surfaces as well as automatically safe profile and Width adjustment. - 2 lamella roller units on the side, each 0.75kW, L=120mm, D=200mm 1 softisc unit Ø=200mm above 0.75kW, 1 slat roller unit L=200mm top 0.75kW, 1 soft disc unit Ø=200mm bottom 0.75kW, 1 slat roller unit L=200mm bottom 0.75kW, 2 lamella roller units on the side, each 0.75kW, L=120mm, D=200mm - Linear guidance of all grinding units Linear ball bearing sets on hardened shafts - time-controlled immersion of all lamella roller units directly above the incoming workpiece edges. By the It is possible to immerse the aggregates deeper into the profiles to be able to deliver. - Motorized workpiece thickness adjustment of the machine - variable grinding flap speed via frequency converter for adjusting the grinding intensity using frequency converters (separate for discs, surface rollers and side rollers) - Disc aggregates as soft discs with Velcro fastener for Grinding wheels (wood pulp) - Feed via three lower and one upper conveyor belts and Spring-loaded pressure rollers with infinitely variable speed 4-15m/min - Parameters that can be set using the touch panel are workpiece thickness, Workpiece width (left side units individually), immersion depth Side units, spindle speed, feed speed - Saving the parameters as machine programs in program mode - Working in automatic mode with non-contact Workpiece width detection and profile detection as well as automatic Adjustment of the sanding units to the workpiece width and the Profile shape (workpiece height is set in advance) - pneumatically clocked driven feed roller, automatic Clamping of the workpiece and feeding in after unit adjustment - Red/green indicator lights to indicate operational readiness - shortest workpiece length 380mm - Transport belt width 200mm - max. workpiece width 180mm (260mm in the envelope process) Nolhcdwovnv Uhs Ijcr - Workpiece height 12-160mm - Suction connection 4 x 100mm and 2x80mm diameter - Sensor-controlled tool blow-off directly on the discs - Length (case) x width x height (mm): 3065x 1600 x 1900 Complete length: 4365mm (including roller conveyor with integrated workpiece width detection) - Weight: 1500kg - Operating voltage 400V, 50Hz, 3P, air connection 6 bar - CE version ----- Price of the above machine on request! ----- Special accessories with additional costs: Set of replacement slats for Leistomat SD-200 consisting of Area aggregates: 30 strips EH45 / 200 - 7 (rolls) 30 strips EH45 / 200 - 20 (rolls) Folding units: 96 strips M55 / 120 - 4 SmartFlex slat disc Ø200 solid with 30 grooves 50mm long Set of replacement slats for SmartFlex slat disc consisting of 60 strip M35 / 50 K 180-7 p Sandpaper disc VB for soft disc D=200mm grit 220 with velor backing (Velcro), pack of 100. Sandpaper disc VB for soft disc D=200mm grit 280 with velor backing (Velcro), pack of 100. ----- Price of the above-mentioned special accessories on request! -----...

Condition: new, Number of sanding units 4 St. sanding width 190 mm Sanding height max. 180 mm LÖWER-DoubleSander Solid DSM 2004 ----- Double-sided four-belt single wood sander for Sanding solid wood such as window frames etc. Highly stable top design with innovative details. Suitable for high continuous loads even with higher chip removals. - sanding units arranged one after the other for pre-grinding, Fine sanding and finishing sanding, each from above and below 1. Belt sanding unit with heavy steel roller 2. Belt sanding unit with rubberized roller and shoe Nelhsvnv Tqocdw Ijcr 3. Finishing unit with fiber brush - Directly driven grinding rollers for slip-free Power transmission - maintenance and wear-free CERMET-coated grinding wheels shoes with very good thermal conductivity and absolute Dimensional accuracy - External cooling of the grinding zones for cooler grinding and longer sanding belt service life - force-guided pneumatically controlled sanding belt oscillation - effective sanding dust extraction directly on the Grinding rollers - Airborne dust extraction on the tension rollers - Integrated brushing and finishing device with large Grinding dust extraction - motorized grinding thickness adjustment via precision threaded spindles and large-sized linear ball screws bearing sets on hardened and ground precision shafts with dust and dirt protection - Adjustment of the chip removal at the bottom via precision Threaded spindle with dimension display via scale ring (Resolution 0.1mm) - Sanding belt tension via pneumatic cylinder constant clamping pressure - Sanding belt change with pneumatic belt relaxation Within seconds - Adjustment option for the sanding belt run Band change - electro-pneumatic compressed air monitoring - Anti-running protection via contact roller if it is too thick workpieces - Workpiece transport via calibrated non-slip and non-stick fixed conveyor belts over heavy, cast tables Finely planed surface and spring-loaded pressure rollers with fine adjustment - Cardan shaft drive for smooth and consistent Workpiece transport - Feed gear motor with stepless speed 4-20 m/min - all motors electrically protected - ergonomically arranged controls - digital thickness display (resolution 0.1mm) with modern Magnetic tape system Technical data: - Sanding belt speed 22 m/s - Sanding belt length 1800mm - Sanding belt width 200mm - Working width 190mm - Grinding thickness 2-180mm - four brake motors for 5.5 kW drive - Feed motor 1.5 kW - Feed speed 4-20 m/min. - automatic height adjustment 0.37 kW - two brush units with fiber brushes D 120 x 200mm at 0.37 kW - Suction nozzle 2 x 180mm 2 x 120mm - Extraction air speed 20 m/s - Pneumatic connection 6 bar - Working height 870mm - Length (with soft disc 2740mm) 2600mm - Length with control panel (with soft disc 3035mm) 2985mm - Width 880mm - Height 1910mm - Weight approx. 3300 kg - Operating voltage 400 volts, 50 Hz, 3P - CE version ----- Price of the above machine on request! ----- Special accessories with additional charge: Workpiece blow-off - using nozzles from above and below at the machine outlet arranged, pneumatically controlled 4-belt sanding belt blowout via nozzles directly on the radii of the tension rollers inside the suction arranged, timer controlled on/off 5 seconds each, can be switched on separately Di...

Condition: used, Number of sanding units 8 st. sanding width 180 (260) mm Sanding height max. 160 mm Dimensions (length / width) 3065x1600x1900 mm weight of the machine ca. 1500 kg Löwer Leistomad SD Window single wood intermediate sanding machine ----- Machine factory tested by Löwer! Automatic fine grinding machine for wood grinding (smoothing, defibering and Edge breaking) or intermediate sanding of profiled window bars. With soft disc Technology for the visible surfaces as well as automatically safe profile and Width adjustment. - 2 lamella roller units on the side, each 0.37kW, L=100mm, D=200mm - 1 softisc unit Ø=200mm above 0.75kW, - 1 slat roller unit L=200mm above 0.75kW - 1 soft disc unit Ø=200mm below 0.75kW, - 1 lamella roller unit L=200mm below 0.75kW, - 2 lamella roller units on the side, each 0.37kW, L=100mm, D=200mm - Linear guidance of all grinding units via linear ball bearing sets hardened waves - Time-controlled immersion of all lamella roller units directly above the incoming workpiece edges. By immersing it is possible To be able to deliver aggregates deeper into the profiles. - Motorized workpiece thickness adjustment of the machine - variable grinding flap speed via frequency converter to adjust the Grinding intensity using frequency converters (separately for discs, surface rollers and side rollers) - Disc aggregates as soft discs with Velcro fasteners for grinding discs (wood pulp) - Feed via three lower and one upper conveyor belt and spring-loaded Pressure rollers with continuous speed 5-15m/min - Parameters that can be set using the touch panel are workpiece thickness and workpiece width (left side units individually), immersion depth of side units, Spindle speed, feed speed - Saving the parameters as machine programs in program mode - Working in automatic mode with non-contact Workpiece width detection and profile detection as well as automatic Adjustment of the sanding units to the workpiece width and profile shape Nelhcdwsvnv Two Ijcr (Workpiece height is set in advance) - pneumatically clocked driven feed roller, automatic clamping of the workpiece as well as retraction after unit adjustment - Red/green indicator lights to indicate operational readiness - shortest workpiece length 380mm - Transport belt width 200mm - max. workpiece width 180mm - Workpiece height 12-120mm - Suction connection 5 x 100mm diameter - Sensor-controlled tool blow-off directly on the discs - Length (housing) x width x height (mm): 3065x 1500 x 1600, complete length: 3800mm (including inlet roller conveyor with stop for Leistomat SD) - Weight: approx. 1500 kg - Operating voltage 400V, 50Hz, 3P, air connection 6 bar - CE version ----- Included options: Adjust the machine as follows: - max. workpiece thickness: 160mm - max. workpiece width: 260mm (in the transshipment process, workpieces must be 2x be allowed through) Transport belt width remains at 200mm - Side units with grinding height 120mm instead of 100mm - more powerful engines for side units 0.75kw instead of 0.37 - larger frequency converters for the side units Quick release disc spindle side for quick tool changes for DiscMaster 4TD or CrossMaster 2TD (only for clockwise rotation) Quick release disc tool for Softdisc, Combidisc or Mediumdisc Ø 250mm (only for clockwise rotation) -----...

Condition: used, Number of sanding units 2 st. sanding width 190 mm Sanding height max. 4-150 mm Hess Junior single wood sander ----- basic structure: Stable, heavy welded construction made of thick-walled rectangular hollow profiles with additional, statically calculated bracing for optimal vibration damping. Staggered grinding units with large dimensioned Belt drive drums for slip-free belt travel. Two-point suction for direct and airborne dust extraction with integrated blow-off device. grinding units in heavy steel plate construction as the basis for vibration-damped, quiet belt run. All guides as a ball linear set on hardened and polished waves. Lasting precision thanks to protection against dust and dirt of the sphere linear sets. Contact roller and sanding pad in a balanced ratio to the grinding belt grain load. The large dimensioned drive drums guarantee the full transmission of the 5.5 kW drive power of the grinding motors on the grinding belt. This means the strongest chip removal possible. Automatic machine stop triggering if the tape breaks. Optical display on control panel. Sanding shoe for finish made of special material with optimal Heat dissipation and additional sliding lining. Easy to use pad change. Abrasive belt tension over appropriately dimensioned compression springs. Sanding belt relaxation for belt change by means of pneumatic Device for sensitive, distortion-free loading of new tapes. Upper Grinding unit and brush device (additional equipment) centrally motorized adjustable. Timber guide in the entry area for hard guide and guide rails supported on both sides pinch rollers. Tilt-proof transport of profiled workpieces calibrated conveyor belts with continuously adjustable feed rate. Nelhcot Tqylodw Iecr Automatic machine stop triggering by wood thickness control device. Optical display of the control panel. Infeed table via fine, precise threaded spindle for lower Grinding chip removal manually adjustable via scale (resolution 0.1 mm). The length Column table guidance guarantees an absolute parallel adjustment. The Adjustment of the flight circle to the outfeed table is achieved by adjusting the height of the lower one Grinding unit via precise threaded spindle and scale display (resolution 0.1 mm) accomplished. Clear, user-friendly arrangement of all electrical functional, operating and display elements on the front of the machine: grinding unit below, Grinding unit above, workpiece transport device, Grinding thickness setting, brushing device above/below, belt utilization, Operating display, fault display. All motors are against overload electrically secured. Technical specifications : ----- Sanding belt speed: 25 m/sec. Grinding width: 190 mm Grinding thickness: 4 - 150 mm Shortest workpiece length: 280 mm Feed speed, continuously adjustable 5 - 25 m/min. Sanding belt dimensions: 200 mm width, 1850 mm length Electrical equipment according to VDE Electrical connection : 400 V., 3/N, 50 Hz. Pneumatic connection: R 3/8", 6 bar, 80 NL grinding units: 2 x 5.5 kW feed: 0.75 kW height adjustment : 0.18 kW Pneumatic connection: R 3/8", 80 NL, min. 6 bar, max. 8 bar Extraction air quantity: 2 x 2000 to 2500 m3/h 20 - 25 m/sec. Extraction connection piece: 2 x 180 mm dia, on top of the machine housing External dimensions: without control cabinet 1750 mm wide, 1850 mm high, 1000 m...