Used Gesan Dpr 100 for sale (23,448)

Condition: excellent (used), CTS Type: TSS-70/130 Water-cooled refrigeration unit For sale is a high-quality thermal shock test chamber by CTS (Clima Temperatur Systeme), model TSS-70/130. This device is designed for performing thermal shock tests and is typically used in industry, research, and quality assurance. Application Areas: - Material testing - Aging tests - Electronics and component testing - Thermal shock and temperature cycling tests Technical Specifications: Type: TSS-70/130 Test volume: 130 liters Temperature range: - Hot chamber: +50°C to +200°C - Cold chamber: -80°C to +100°C Heating rate: approx. 6 K/min from ambient temperature to +180°C Cooling rate: approx. 4 K/min from ambient temperature to -60°C Temperature deviation: - ±1 K over time - ±2 K spatially Temperature change rate: - max. 100 K/min average for shock test mode (no radiant heat) Transfer time between chambers: - ≤ 15 min for -65°C to +200°C with 10 kg ICs Changeover time: - < 10 seconds Electrical Specifications: Connection: 400 V, 3/N, 50 Hz Nominal power: approx. 17.2 kW Nominal current: approx. 29 A Site fuse: 32 A slow-blow Connection: Cekon 32 Refrigeration System: Refrigerant: R404A / R23 Water-cooled, low noise, fully hermetic Features/Equipment: - CTS control panel - Microprocessor-controlled regulation and monitoring system - Programmable operation (up to 100 test programs) - Digital setpoint and actual value display - RS232 interface - 2 free switching channels for external device control - Fault notification via volt-free contact (Loadable up to 30 V DC, 2 A) - EMC tested Technical Construction: Njdpfx Ahey Hkd He Nsla - Hot and cold chambers - Transfer basket with spindle drive - Test chamber/transfer basket made of stainless steel (material no. 1.4301) - Stainless steel wire insert basket - Tube port NW 50 with sealing plug - Compressed air connection 1/4" male - Non-pressurized condensate drain R 1/2" female thread - Safety door locking - Lockable door with window Dimensions (according to installation diagram): External dimensions approx.: 2335 x 940 x 1820 mm Installation clearance approx.: 1990 x 940 x 1652 mm Test chamber internal dimensions: height approx. 410 mm, width approx. 480 mm, depth approx. 660 mm Window: 300 x 300 mm Additional Data: Protection class: IP 22 Sound pressure level: < 60 dB(A) Weight: approx. 950 kg Average consumption during test cycle: approx. 8 kWh Important information for your safety as a buyer! The following points are performed on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. If required, refill with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, chambers undergo a documented test run. Condition: used Scope of delivery: see photos (Specifications subject to change and errors excepted.) For further questions, please feel free to contact us by phone.

Condition: good (used), functionality: fully functional, Door lock milling machine SL 100 - with milling motors for faceplate and handle - with pneumatic clamps Nledpfxoygm Awe Ah Noa - 1.7 kW Transport available at extra cost!

Condition: used, Year of construction: 2014, Suitable for extracting oil mist. Nominal volume flow: 950 m³/h noise level: 71 dB (A) number of revolutions: 2850 rpm Dimensions W x D x H approx.: 525 x 592 x 781 mm Weight approx.: 55 kg Nodpfjwnprxox Ah Nela Connected load approx.: 0.75 kW (400 V / 50 Hz), colour: Grey

Condition: used, net belt width ± 600 mm total electrical power 33 kW thermal connection: NW32 2x5 tiers product height: ± 100 mm cooking time min/max : 4-40 min max. temperature: 200°C automatic elevator with belt wash system Nlodpfxsy Emtuj Ah Nja suitable for CIP-cleaning suitable for steam injection (heating and product yield): 4-8 bar, connection: NW 40 turning to the left

Condition: used, Year of construction: 2005, Horizon brochure production line consisting of: VAC-100 vacuum collating tower (2 units) SPF-20A stapling and folding module FC-20A front trimmer Technical data: Horizon VAC-100 – vacuum collating tower Function: Collating printed sheets Number of stations per tower: 10 (20 in total with 2 towers) Paper format: min. 120 × 148 mm, max. 350 × 500 mm Paper weight: 52–208 g/m² (up to 300 g/m² in some cases) Stack height per compartment: 55 mm Production speed: up to 9,900 sets/hour Control: touchscreen control panel Horizon SPF-20A – Stapling and folding module Function: Stapling and folding brochures Stapling heads: 2 × Hohner 48/5 Paper size: 120 × 180 mm to 350 × 500 mm Final format: 90 × 120 mm to 250 × 350 mm Stapling thickness: max. 4 mm (stapling only), max. 2 mm (stapling + folding) Stapling distance: 73–160 mm Wire diameter: 0.5 mm Nlsdpfxexpv Ado Ah Nja Production speed: up to 4,050 brochures/hour (A5), approx. 3,200 brochures/hour (A4) Power consumption: approx. 450 W Dimensions: 271 × 81 × 110 cm Weight: approx. 490 kg Horizon FC-20A – Front trimmer Function: Front edge trimming of brochures Brochure size: max. 250 × 20 mm; min. 85 mm Trim size: max. 20 mm Processing: min. 4 pages / max. 88 pages (at 80 g/m²) Production speed: up to 3,400 cycles/h Power supply: 230 V / 50 Hz, 0.2 kW Dimensions: 610 × 810 × 1,070 mm Weight: approx. 240 kg

Condition: excellent (used), Year of construction: 1998, Haffner Door Lock Mortising Machine used, in good condition Manufacturer: Haffner Model: SL 100 Machine No.: 5372 Column-type machine Chain mortising unit Door support Workpiece support Nledpfeyuty Ssx Ah Nja Spindle for lever hole Spindle for faceplate Lubrication device Extraction port D 80/100 mm Required space approx. 1200 mm x 700 mm x 2000 mm Weight approx. 300 kg Location: 54634 Bitburg Delivery in as-inspected condition, without warranty or guarantee

Condition: used, Year of construction: 1997, operating hours: 3,861 h, overall weight: 1,500 kg, rotor diameter: 235 mm, total length: 2,500 mm, total height: 2,500 mm, total width: 1,500 mm, rotor width: 794 mm, power: 11 kW (14.96 HP), filling opening width: 800 mm, filling opening length: 1,000 mm, No. 04527 Single-shaft shredder Vecoplan VAZ 100/80 U40 Used, year of construction 1997, 3861 operating hours The waste shredder VAZ 100/80 is designed for shredding wood waste, pallets, crates, particleboard and fiberboard, paper and cardboard, plastics, etc. The machine is most commonly used to produce fuel chips from wood waste, wood scraps, and pallets. Feed opening 1000 x 800 mm LW Universal rotor, tool size 40 Connected load 13 kW, drive power 11 kW Throughput capacity for logs 250 - 350 kg/h Throughput capacity for particleboard 800 - 1000 kg/h Screen hole size (diameter) 25 mm Rotor diameter 235 mm, rotor width 794 mm, speed 95 rpm Rotor mounted in self-aligning roller bearings with steel housing Feed unit made of channel steel, driven by hydraulic cylinders Guided in brass rails, with rollers on the sides Main drive via gear motor with two-stage worm gear Motor speed 95 rpm Automatic foreign object breakage protection PLC control, automatic mode / manual mode Hydraulic unit with 2 operating speeds 2 suction connections on the sides, 200 mm each Currently, the machine is designed so that the wood chips fall downward. If the opening at the bottom is closed, an extraction system could be connected. Includes 1 new counter blade, various cutting blades, complete technical documentation Transport dimensions approx. 2500 x 1500 x 2500 mm LWH Weight approx. 1500 kg To avoid possible misunderstandings, an on-site inspection is possible and recommended by appointment Sold as is Nljdpoy Hlgiefx Ah Noa Technical specifications, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “sold as seen” Terms of payment: Prices plus VAT, payment before collection or shipping Terms of delivery: ex warehouse

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, tool type: HSK 100, We are offering a comprehensive lot of approximately 200 HSK-100 tool holders in various versions for sale. Njdpfx Aey Hfnmoh Nola These tool holders come from productive use on a WFL Millturn M 100 and were utilized there for a range of turning, drilling, and milling operations. The inventory includes tool holders from different years of manufacture, approximately from 2006 to 2020. The scope of supply includes tool holders and systems from renowned manufacturers such as BENZ, Gühring, Wohlhaupter, and other established brands. Included are various types, such as milling holders, drilling and boring tools, special holders, adapters, and other HSK-100 tooling devices. The attached photos show the tool holders both in their previous mounted use on the machine or at the operator station, as well as in their current stored condition in our warehouse. This lot is especially suitable for operators of WFL Millturn machines or other comparable machining centers equipped with HSK-100 interfaces. An inspection can be arranged by appointment. Additional detailed photos of individual tool holders, manufacturer markings, or nameplates can be provided upon serious inquiry.

Condition: excellent (used), Desposer kitchen waste disposal unit, waste shredder, garbage chute -Power: 0.75 kW -Voltage: 230/460 V -Speed: 1725 rpm (60Hz) -Connection: Ø 170 mm -Quantity: 2 available Price: per piece Nedpeb A Hp Iefx Ah Nsla -Dimensions: 230/H440 mm -Weight: 20 kg

Condition: like new (used), Year of construction: 2008, Retrofitted: 2026 Nlsdpfx Ajyvwchoh Nea Numerical control: SIEMENS 840D Technical features Dimensions Table dimensions: OptionalMaximum weight on table (kg/m2): OptionalNumber of T slots: UndefinedT slots dimensions: Undefined Traverses of axis X axis traverse: 10000 mmY axis traverse: 1500 mmZ axis traverse: 2500 mmVertical capacity (VC): 0 - 2500 mm (adjustable) Milling head Head type: Universal Auto-indexing UAD (0,1º)Tool clamping system: HydraulicTaper nose: ISO 50 (DIN 69871) / Pull stud: DIN 69872Speed range: 20 - 6000 rpmSpindle power: 30 kW Feedrates Rapid feedrate (X / Y-Z): 30000 mm/min Weight and dimensions Machine weight approx.: 70000 kgMachine dimensions approx.: 17560 x 12800 x 4270 mm Accessories Guarding: pendular with automatic front door and peripheral safety fenceAutomatic tool changer: ATC80 with electrical motorsChip conveyor: 1 front longitudinal and 1 transversalExternal coolant high-pressure coolant through spindleElectronic handwheel: 6FX2007-1AE14 SiemensOperator´s cabinet: adjustable in vertical traverse Other technical features 2 ROTARY TABLES:Model:   DEMMELER DRLTS1800Table surface: 2400 x 1800 mmMaximum load on table: 40 TT slots number: 9T slots dimensions: 22 mmRotary axis: HydrostaticMaximun speed (S1/S6): 3.4 / 5.4 r.p.m.Clamped tangencial torque: 175000 NmW axis: 1500 imum feedrate: 20000 mm/ntity of guideway (W axis): 4 Sale conditions Warranty: 6 months mechanical partsPrice and sale conditions: On request View all technical features

Condition: used, Year of construction: 2019, Incl. tools CNC-CONTROLLED MACHINING CENTER morbidelli m100 Drilling and milling made for you! This numerically controlled machining center is equipped with a wide range of milling and drilling tools to meet every woodworking requirement. - Highly powerful - with 8,000 rpm drilling spindles and . technology, the most stable spindle available on the market, with more than 1,000 maintenance-free hours of use. - Optimally and comprehensively equipped - the vacuum cleaners can be individually configured with the TV FLEX work table to customize the machine to meet individual requirements. - Easy and understandable programming thanks to the integrated Cad-Cam MAESTRO CNC software - Easy to operate; the lowered machine frame makes the work table accessible at all times. The control cabinet and vacuum pump are integrated into the machine bed, and in the PRO SPACE version, no additional structural protective measures are necessary. Supporting structureThe supporting structure consists of a particularly strong monolithic steel base, ribbed and very robust. The particularly wide support was specifically designed to give the machine stability, ensuring constant precision in all working conditions. The machine does not need to be anchored to the ground. The base provides a large and solid support for the mobile column: the work unit is equipped with a balanced, stable and resistant support that can withstand the most extreme stresses, ensuring superior performance and greater precision. The mobile gantry consists of a solid single part anchored to the base and the work unit is fixed to it and moves along Y and Z axes, also on prismatic guides with ball return sliding blocks of the highest quality. The movement of the lower moving unit (X-axis) and the working unit along the crosshead of the moving unit (Y-axis) is achieved thanks to the power transmission via a rack and pinion with helical teeth; This creates a greater tooth-to-tooth thrust, which achieves greater acceleration and higher speed along the X and Y axes. The specially designed helical gearing ensures less wear on the mechanical components and less noise. The vertical Z axis is driven by a screw with ball return, which ensures perfect balance with dynamic loading and strong acceleration and deceleration. The main milling unit is directly coupled to the Z axis carriage and ensures very high quality finishing as vibrations are completely eliminated. Translation along the X-Y-Z axes is carried out by brushless motors driven by static inverters. These ensure:- Reduced machining times thanks to improved acceleration- Better positioning accuracy thanks to the high resolution encoder- Elimination of setup operations when switching on the machine thanks to absolute encoders- Elimination of general maintenance operations as there are no brushes with the "brushless" systemThe management of the axis displacement and in general of the working elements of the machine is done via e Nlodpfx Aovvi Scjh Nea

Condition: excellent (used), Machining Center MASTERWOOD TF 100 2.0 -used- Through-feed processing, Ball screw spindles on all axes, Network card for remote maintenance, Integrated control cabinet, Saw unit for grooving in X-direction, Pick-up tool changer, Automatic central lubrication, Panel measuring sensor, New drill set, New grooving saw blade, Clamex option available, Door processing option available ----- Technical Data ----- Min. workpiece length X: unlimited, Min. workpiece length Y: 1,000 mm, Nsdpfxsy Eylws Ah Njla Min. workpiece thickness: 60 mm, Number of vertical drilling spindles: 10 pcs, Number of horizontal double drilling spindles in X-direction: 2 pcs, Number of horizontal double drilling spindles in Y-direction: 1 pc, Saw blade diameter of saw unit: 120 mm, Number of tools in the changer: 6 pcs, Extraction port diameter: 150 mm, Compressed air connection: 6-8 bar, Dimensions (LxWxH): 1,920 x 2,818 x 1,620 mm, Weight: 1,500 kg Quality Information: - Full basic cleaning - Electrical system checked - Pneumatic system checked - Set according to manufacturer's specifications - Immediately ready for operation

Condition: new, Year of construction: 2025, pressure 100 t stroke 380 mm table surface area 1100x424 mm Njdpfx Ahexu Nv Io Nsla dayligth 180/750 mm distance between columns 1100 mm diameter of piston 90 mm

Condition: used, machine/vehicle number: 005836, X axis working area: 3000 mm Y axis working area: 1000 mm Main Electrospindle power: 3.5 KW Number of controlled axes: 3 axes Total number of drilling spindles: 82 Nlsdpfx Ahewuckuj Noa

Condition: used, Year of construction: 2002, functionality: fully functional, input voltage: 380 V, input frequency: 50 Hz, pressing force: 100 t, stroke length: 130 mm, overall weight: 9,500 kg, Model: PREN-100 Year: 2002 Weight: 9,500 kg Nlodpfx Ahsy E Hccj Nja Nominal force: 100 t Type: Eccentric press with pneumatic clutch Stop position: 580 mm Shut height: 450 mm Max. flywheel RPM: 500 Stroke: 13-130 mm Max. slider adjustment: 80 mm Motor: 11 kW 380 V 50 Hz Min. air pressure: 3.5 - 6 bar Stop time: 285 ms Safety distance: 486 mm

Condition: good (used), electric motor, three-phase motor Nledpfxsy D Ikxe Ah Noa -Manufacturer: AEG, electric motor type AM 100 LT6 -Power: 1.5 kW -Speed: 920 rpm -Shaft: Ø 28 x 60 mm -Protection rating: IP54 -Design: B3 -Dimensions: 365/250/H210 mm -Weight: 23 kg

Condition: used, functionality: fully functional, Year of construction: 2021, operating hours: 1,220 h, load capacity: 2,000 kg, fuel type: electric, fork length: 1,150 mm, empty load weight: 700 kg, total length: 670 mm, drive type: Elektro, construction width: 730 mm, Low lift pallet truck Load center: 600 mm Mast type: None Technical condition: very good Front tires type: Polyurethane Front tires condition: 100% Rear tires type: Polyurethane Nsdpjykvxijfx Ah Nela Rear tires condition: 100% Battery voltage: 24V Battery capacity: 400Ah Battery manufacturer: Kapatest 100% Battery year: 2021 Description: Factory-refurbished used equipment from Toyota, including new inspection and new approval according to FEM (formerly UVV). Pulse control, CE certificate,

Condition: good (used), Year of construction: 2011, functionality: fully functional, pressing force: 100 t, stroke length: 315 mm, overall weight: 8,000 kg, Hydraulic Press Brake Manufacturer: BYSTRONIC Model: Xpert 100/2050 Year of manufacture: 2011 Technical Data Make: BYSTRONIC Model: Xpert 100/2050 Year: 2011 Press Force: 100 t Bending Length: 2000 mm Stroke: max. 315 mm Motor Power: 7.5 kW Dimensions: approx. L 3.10 x W 1.90 (plus support arms) x H 2.85 m Weight: approx. 8 t Equipment: • Controlled axes: Y1, Y2, X, R, Z1, Z2 • PILZ Fast Bend light barrier • Controller: MMC BYBEND • Hydraulic tool clamping (top and bottom) • Hydraulic pressing table!!! • Movable support arms • CNC-controlled crowning • 1 upper tool, gooseneck, H 150mm, 80°, segmented Nlsdpfx Ajy Ef Rxoh Nja • 1 lower tool V12 All information is supplied without liability. A demonstration in our showroom is possible at any time.

Condition: used, functionality: fully functional, Year of construction: 2018, operating hours: 380 h, load capacity: 200 kg, empty load weight: 2,650 kg, construction height: 1,990 mm, fuel type: electric, total length: 2,820 mm, drive type: Elektro, arm reach: 3,000 mm, construction width: 990 mm, working height: 9,900 mm, Vertical lift platform Technical condition: good Front tyres type: solid (bandage) Front tyres size: 16-5-11 1/4 Front tyres condition: 80 - 100% Rear tyres type: solid (bandage) Rear tyres size: 16-5-11 1/4 Rear tyres condition: 80 - 100% Battery voltage: 24V Battery capacity: 250Ah Battery type: PzS Nledpey Etzfofx Ah Nsa Battery year: 2018 Battery condition: 80 - 100%

Condition: not inspected (used), Year of construction: 1989, functionality: unexamined, machine/vehicle number: 1616, travel distance X-axis: 300 mm, travel distance Y-axis: 300 mm, travel distance Z-axis: 300 mm, feed rate X-axis: 450 m/min, spindle speed (max.): 2,500 rpm, No reserve price - guaranteed sale to the highest bidder! Placing a bid commits you to collect the item within the scheduled period between 23.06.2026 and 26.06.2026! TECHNICAL DETAILS Travel X-axis: approx. 300 mm Travel Y-axis: approx. 300 mm Travel Z-axis: approx. 300 mm Spindle speed range: 40 to 2,500 rpm Table dimensions: 600 x 210 mm Number of feeds: 16 Feed rates: 28 to 450 mm/min Number of slots: 4 Nodpfx Ahoy D Shno Nela Tool holder: SK 40 MACHINE DETAILS Dimensions & weight Dimensions (L x W x H): 2,000 x 1,200 x 1,700 mm Machine weight: 1,000 kg EQUIPMENT Mounted vice (jaw width: 110 mm) Set of tool holders Milling cutters Collets Three-axis digital readout (manufacturer: FAGOR) External reference: 10

Condition: new, Year of construction: 2025, New machine Year of manufacture: 2025 Features and technical data: Planing width: 630 mm Planing height: 3 - 300 mm Maximum cutting depth: 8 mm Table length: 1100 mm Cutterhead speed: 5000 rpm Feed motor power: 0.55 / 0.75 kW / 0.8 / 1.0 HP Extraction port Ø 160 mm, usable on left and right Feed speed: 7 + 14 m/min Main motor power: 7.5 kW / 10 HP Voltage: 400 V / 50 Hz Space requirement approx. 1070 x 1200 x 1060 mm Net weight approx. 1050 kg TECHNICAL DESCRIPTION Robust German engineering. For thickness planing with a planing width up to 630 mm and planing height from 3 to 300 mm, compact and ergonomic machine dimensions. PANHANS solid steel cutterhead Ø 125 mm with 4 Tersa reversible knives. Pendulum-mounted feed rollers. Segmented rubber infeed and outfeed rollers with Ø 90 mm ensure smooth and secure workpiece feed. With segmented pressure bar. Electric height adjustment of the thicknessing table, tilt-resistant on 4 trapezoidal thread spindles. With finely planed thickness table. Positioning control 4.3" touchscreen. Automatic star-delta start. Mechanical motor brake. Extraction port 160 mm, usable on left and right. Machine calibrated at the factory. CE compliant GS tested Standard equipment as follows: Solid steel cutterhead with 4 Tersa reversible knives Standard quality for 630 mm planing width Rubber infeed roller Nsdpey Eizuefx Ah Njla Rubber outfeed roller Thickness table without table glide rollers Positioning control 4.3" touchscreen 2 feed speeds 7 + 14 m/min Touch panel 4.3" Location: Flörsheim Availability: Immediately

Condition: ready for operation (used), Year of construction: 2008, This 3-axis Baublys Control Laser UL 65QR/NC 100 50 50 SOMA was manufactured in 2008. It features a Q-switched solid-state Nd:YAG laser, capable of reaching frequencies up to 50 kHz. The machine includes a round transfer table of approximately 75 cm and is housed in a 2.4 x 2.6 meters enclosure. If you are looking to get high-quality laser marking capabilities consider the Baublys Control Laser UL 65QR/NC 100 50 50 SOMA machine we have for tact us for more information. Nlodpfx Asx Sz Efoh Nsa • Laser type: Q-switched solid-state laser • Laser medium: Nd:YAG • Wavelength: 1064 nm • Beam quality (M²): 13 (6 kHz, MM);

Condition: excellent (used), Catalogue number 7972 TECHNICAL DATA - Inlet width: 300mm - Inlet height: 100mm - Shaft width: 330mm - Knife length: 330mm - Number of knives: 2 pcs - Screen dimensions: 30x30mm - Lower toothed feed shaft - Lower shaft motor: 1.5kW - Upper toothed feed shaft - Upper shaft motor: 1.5kW - Vibrating chute - Vibrating chute length: 1960mm Nlsdpfx Ahoy E Iwze Nea - Vibrating chute width: 300mm - Vibrating chute motor approx. 0.75kW - Main motor: 22kW - Auto-reverse (adjustable) - Extraction nozzle diameter: 200mm - Overall machine dimensions (L/W/H): 1550x1050x840mm - Overall vibrating chute dimensions (L/W/H): 1960x490x570mm - Weight: 1150kg ADVANTAGES – German-made – Auto-reverse (adjustable) – protects the machine from blockage and damage in case of overload – DTR documentation – Used chipper, in very good condition Net price: 39,900 PLN Net price: 9,500 EUR (depending on exchange rate of 4.2 EUR) (Prices may change with significant fluctuations)

Condition: good (used), Year of construction: 2008, Ref. -No.: 10624 Manufacturer: HEDELIUS Type: RS 100 MAGNUM Year of construction: 2008 Type of control: CNC Control: HEIDENHAIN 530i Storage location: Halberstadt Country of origin: Germany X-Travel: 3500 mm Y-Travel: 1000 mm Z-Travel: 770 mm Main spindle drive power: 55 kW Table Load: 4000 kg Max. Tool Weight: 20 kg Max. Tool Length: 330 mm Max. Tool Diameter: 125 mm Tool Taper: SK 50 Tool Piece Magazine With: 50 Pcs./pcs. Turning Speeds: 6000 RPM Feed Speeds X/Y/Z Axis: 30000 mm / min Further information: - With rotary/swivel table (1.00 x 0.80 m) - Guide rail cover replaced The machine can be viewed while powered up. Nljdoy Ed Rwopfx Ah Nja

Condition: good (used), Year of construction: 1997, pressure 100 t stroke 300 mm table surface area 500 x 1520 mm column travel between the guideways 1520 mm dayligth 680 mm pressure max. 244 bar weight of tools max. 270 kg ajustment speed 8.0 mm/sec working feed 5.0 mm/sec return speed 10.0 mm/sec oil volume 90.0 l Nlsdpsy Dh Nzefx Ah Nsa voltage 400 V total power requirement 7.5 kW weight of the machine ca. 2700 kg dimensions of the machine ca. 2630 x 1000 x 2350 mm current new price approx. 18.000 euros special price on request according to previous owner rarely in use Equipment: - robust electro-hydraulic workshop/bending press * left right guided - with fixed working cylinder - Pressing depth adjustable by cams - Height-adjustable work table - 2x locking bolts for table fixation - 3x directional control valve supply-empty-return - Stepless adjustment of working pressure - 1x freely movable 2-hand operation - Original operating instructions